Академический Документы
Профессиональный Документы
Культура Документы
A PROJECT REPORT ON
CERTIFICATE
EXTERNAL EXAMINER
ACKNOWLEDGEMENT
The satisfaction and euphoria that accompany the successful completion of any task would be incomplete without the mentioning of the people whose constant guidance and encouragement made it possible. We take pleasure in presenting before you, our project, which is result of studied blend of both research and knowledge.
We express our earnest gratitude to our internal guide, Assistant Professor ___________, Department of ECE, our project guide, for his constant support, encouragement and guidance. We are grateful for his cooperation and his valuable suggestions.
DECLARATION
___________ ___________
___________ ____________
__________ ___________
CONTENTS
1. ABSTRACT 2. INTRODUCTION TO EMBEDDED SYSTEMS 3. BLOCK DIAGRAM 4. HARDWARE REQUIREMENTS 4.1 TRANSFORMERS 4.2 VOLTAGE REGULATOR (LM7805) 4.3 RECTIFIER 4.4 FILTER 4.5 MICROCONTROLLER (AT89S52/C51) 4.6 ADC0808 4.7 4.8 4.9 MAX232 ULN2003 RELAY DRIVER
PAGE NO.
13 13 15
17 19
22
4.15 CAPACITORS 5. SOFTWARE REQUIREMENTS 5.1 IDE 5.2 CONCEPT OF COMPILER 5.3 CONCEPT OF CROSS COMPILER 5.4 KEIL C CROSS COMPILER 57 57 58 59
6
59
5.6 CREATING YOUR OWN APPLICATION IN UVISION2 59 5.7 DEBUGGING AN APPLICATION IN UVISION2 5.8 STARTING UVISION2 & CREATING A PROJECT 5.9 WINDOWS_ FILES 5.10 BUILDING PROJECTS & CREATING HEX FILES 5.11 CPU SIMULATION 5.12 DATABASE SELECTION 5.13 START DEBUGGING 5.14 DISASSEMBLY WINDOW 5.15 EMBEDDED C 6. SCHEMATIC DIAGRAM 6.1 DESCRIPTION 7. LAYOUT DIAGRAM 8. BILL OF MATERIALS 9. CODING 9.1 COMPILER 9.2 SOURCE CODE 10. HARDWARE TESTING 10.1 CONTINUITY TEST 10.2 POWER ON TEST 11. RESULTS 12. CONCLUSION 60 61 61 61 62 62 63 63 64 66 67 71 72 75 76 84 88 88 89 69 93
7
13. BIBLIOGRAPHY
94
LIST OF FIGURES
2(a) EMBEDDED DESIGN CALLS 2(b) V DIAGRAM 3. BLOCK DIAGRAM OF THE PROJECT 4.1 A TYPICAL TRANSFORMER 4.2 BLOCK DIAGRAM OF VOLTAGE REGULATOR 4.2(a) PERFORMANCE CHARACTERISTICS OF VOLTAGE REGULATOR 4.5 BLOCK DIAGRAM OF AT89S52 4.5(b) PIN DIAGRAM OF AT89S52 4.5(c) OSCILLATOR CONNECTIONS 4.5(d) EXTERNAL CLOCK DRIVE CONFIG. 4.6 ADC0808 4.8(a) LOGIC DIAGRAM OF ULN2003 4.8(b) SCHEMATIC DIAGRAM OF ULN2003
PAGE NO.
17
20
21 24 25 29 30 31 37 38 39 42
4.8(c) RELAY SHOWING COIL & SWITCH CONTACTS 6. SCHEMATIC DIAGRAM OF THE PROJECT 7. PROJECT LAYOUT
64 66
ABSTRACT
{PLEASE REFER CD}
and hardware layout designed for the specific purpose. Examples Small controllers and devices in our everyday life like Washing Machine, Microwave Ovens, where they are embedded in.
Embedded systems have a microprocessor/ microcontroller and a memory. Some have a serial port or a network connection. They usually do not have keyboards, screens or disk drives.
2) C om m u ni c at i o n Ap p l i c at i on s 3) In d us t ri al aut om at i o n and p ro c es s co nt r ol s o ft w a r e 4) Mastering the complexity of applications. 5) Reduction of product design time. 6) Real time processing of ever increasing amounts of data. 7) Intelligent, autonomous sensors.
CLASSIFICATION Real Time Systems. RTS is one which has to respond to events within a specified deadline. A right answer after the dead line is a wrong answer
RTS CLASSIFICATION Hard Real Time Systems Soft Real Time System
HARD REAL TIME SYSTEM "Hard" real-time systems have very narrow response time. Example: Nuclear power system, Cardiac pacemaker.
SOFT REAL TIME SYSTEM "Soft" real-time systems have reduced constrains on "lateness" but still must operate very quickly and repeatable. Example: Railway reservation system takes a few extra seconds the data remains valid.
13
3. BLOCK DIAGRAM
14
4. HARDWARE REQUIREMENTS
HARDWARE COMPONENTS:
1. TRANSFORMER (230 12 V AC) 2. VOLTAGE REGULATOR (LM 7805) 3. FILTER 4. RECTIFIER 5. MICROCONTROLLER (AT89S52/AT89C51) 6. ADC0808
15
7. MAX232 8. RELAYS
9. DB9 CONNECTOR 10. LM35 TEMPERATURE SENSOR 11. ULN2003 12. LED 13. IN4007 14. RESISTORS 15. CAPACITORS
4.1 TRANSFORMER
Transformers convert AC electricity from one voltage to another with a little loss of power. Step-up transformers increase voltage, step-down transformers reduce voltage. Most power supplies use a step-down transformer to reduce the dangerously high voltage to a safer low voltage.
16
The input coil is called the primary and the output coil is called the secondary. There is no electrical connection between the two coils; instead they are linked by an alternating magnetic field created in the soft-iron core of the transformer. The two lines in the middle of the circuit symbol represent the core. Transformers waste very little power so the power out is (almost) equal to the power in. Note that as voltage is stepped down and current is stepped up. The ratio of the number of turns on each coil, called the turns ratio, determines the ratio of the voltages. A step-down transformer has a large number of turns on its primary (input) coil which is connected to the high voltage mains supply, and a small number of turns on its secondary (output) coil to give a low output voltage. TURNS RATIO = (Vp / Vs) = ( Np / Ns ) Where, Vp = primary (input) voltage. Vs = secondary (output) voltage Np = number of turns on primary coil Ns = number of turns on secondary coil Ip = primary (input) current Is = secondary (output) current.
17
The ideal transformer as a circuit element If the secondary coil is attached to a load that allows current to flow, electrical power is transmitted from the primary circuit to the secondary circuit. Ideally, the transformer is perfectly efficient; all the incoming energy is transformed from the primary circuit to the magnetic field and into the secondary circuit. If this condition is met, the incoming electric power must equal the outgoing power:
Transformers normally have high efficiency, so this formula is a reasonable approximation. If the voltage is increased, then the current is decreased by the same factor. The impedance in one circuit is transformed by the square of the turns ratio. For example, if an impedance Zs is attached across the terminals of the secondary coil, it appears to the primary circuit to have an impedance of (Np/Ns)2Zs. This relationship is reciprocal, so that the impedance Zp of the primary circuit appears to the secondary to be (Ns/Np)2Zp.
18
Description The LM78XX/LM78XXA series of three-terminal positive regulators are available in the TO-220/D-PAK package and with several fixed output voltages, making them useful in a Wide range of applications. Each type employs internal current limiting, thermal shutdown and safe operating area protection, making it essentially indestructible. If adequate heat sinking is provided, they can deliver over 1A output Current. Although designed primarily as fixed voltage regulators, these devices can be used with external components to obtain adjustable voltages and currents.
19
20
4.3 RECTIFIER
A rectifier is an electrical device that converts alternating current (AC), which periodically reverses direction, to direct current (DC), current that flows in only one direction, a process known as rectification. Rectifiers have many uses including as components of power supplies and as detectors of radio signals. Rectifiers may be made of solid state diodes, vacuum tube diodes, mercury arc valves, and other components. The output from the transformer is fed to the rectifier. It converts A.C. into pulsating D.C. The rectifier may be a half wave or a full wave rectifier. In this project, a bridge rectifier is used because of its merits like good stability and full wave rectification. In positive half cycle only two diodes( 1 set of parallel diodes) will conduct, in negative half cycle remaining two diodes will conduct and they will conduct only in forward bias only.
21
4.4 FILTER
Capacitive filter is used in this project. It removes the ripples from the output of rectifier and smoothens the D.C. Output received from this filter is constant until the mains voltage and load is maintained constant. However, if either of the two is varied, D.C. voltage received at this point changes. Therefore a regulator is applied at the output stage. The simple capacitor filter is the most basic type of power supply filter. The use of this filter is very limited. It is sometimes used on extremely high-voltage, low-current power supplies for cathode-ray and similar electron tubes that require very little load current from the supply. This filter is also used in circuits where the power-supply ripple frequency is not critical and can be relatively high. Below figure can show how the capacitor charges and discharges.
22
23
system to continue functioning. The Power-down mode saves the RAM contents but freezes the oscillator, disabling all other chip functions until the next interrupt or hardware reset.
Features:
Compatible with MCS-51 Products 8K Bytes of In-System Programmable (ISP) Flash Memory Endurance: 10,000 Write/Erase Cycles 4.0V to 5.5V Operating Range Fully Static Operation: 0 Hz to 33 MHz Three-level Program Memory Lock 256 x 8-bit Internal RAM 32 Programmable I/O Lines Three 16-bit Timer/Counters Eight Interrupt Sources Full Duplex UART Serial Channel Low-power Idle and Power-down Modes Interrupt Recovery from Power-down Mode Watchdog Timer Dual Data Pointer Power-off Flag Fast Programming Time Flexible ISP Programming (Byte and Page Mode) Green (Pb/Halide-free) Packaging Option
24
low will source current (IIL) because of the internal pull-ups. In addition, P1.0 and P1.1 can be configured to be the timer/counter 2 external count input (P1.0/T2) and the timer/counter 2 trigger input (P1.1/T2EX). Port 2: Port 2 is an 8-bit bidirectional I/O port with internal pull-ups. The Port 2 output buffers can sink/source four TTL inputs. When 1s are written to Port 2 pins, they are pulled high by the internal pull-ups and can be used as inputs. As inputs, Port 2 pins that are externally being pulled low will source current (IIL) because of the internal pull-ups. Port 2 emits the high-order address byte during fetches from external program memory and during accesses to external data memory that use 16-bit addresses (MOVX @ DPTR). In this application, Port 2 uses strong internal pullups when emitting 1s. During accesses to external data memory that use 8-bit addresses (MOVX @ RI), Port 2 emits the contents of the P2 Special Function Register. Port 3: Port 3 is an 8-bit bidirectional I/O port with internal pull-ups. The Port 3 output buffers can sink/source four TTL inputs. When 1s are written to Port 3 pins, they are pulled high by the internal pull-ups and can be used as inputs. As inputs, Port 3 pins that are externally being pulled low will source current (IIL) because of the pull-ups. RST: Reset input. A high on this pin for two machine cycles while the oscillator is running resets the device. This pin drives high for 98 oscillator periods after the Watchdog times out. The DISRTO bit in SFR AUXR (address 8EH) can be used to disable this feature. In the default state of bit DISRTO, the RESET HIGH out feature is enabled. ALE/PROG: Address Latch Enable (ALE) is an output pulse for latching the low byte of the address during accesses to external memory. This pin is also the program pulse input (PROG) during Flash programming. In normal operation, ALE is emitted at a constant rate of 1/6 the oscillator frequency and may be used for external timing or clocking purposes. Note, however, that one ALE pulse is skipped during each access to external data memory.
27
PSEN: Program Store Enable (PSEN) is the read strobe to external program memory. When the AT89S52 is executing code from external program memory, PSEN is activated twice each machine cycle, except that two PSEN activations are skipped during each access to external data memory. EA/VPP: External Access Enable. EA must be strapped to GND in order to enable the device to fetch code from external program memory locations starting at 0000H up to FFFFH. Note, however, that if lock bit 1 is programmed, EA will be internally latched on reset. EA should be strapped to VCC for internal program executions. This pin also receives the 12-volt programming enable voltage (VPP) during Flash programming.
XTAL1: Input to the inverting oscillator amplifier and input to the internal clock operating circuit. XTAL2: Output from the inverting oscillator amplifier
Oscillator Characteristics: XTAL1 and XTAL2 are the input and output, respectively, of an inverting amplifier which can be configured for use as an on-chip oscillator, as shown in Figure 1. Either a quartz crystal or ceramic resonator may be used. To drive the device from an external clock source, XTAL2 should be left unconnected while XTAL1 is driven as shown in Figure 6.2. There are no requirements on the duty cycle of the external clock signal, since the input to the internal clocking circuitry is through a divide-by-two flip-flop, but minimum and maximum voltage high and low time specifications must be observed.
28
Idle Mode In idle mode, the CPU puts itself to sleep while all the on chip peripherals remain active. The mode is invoked by software. The content of the on-chip RAM and all the special functions registers remain unchanged during this mode. The idle mode can be terminated by any enabled interrupt or by a hardware reset. Power down Mode In the power down mode the oscillator is stopped, and the instruction that invokes power down is the last instruction executed. The on-chip RAM and Special Function Registers retain their values until the power down mode is terminated. The only exit from power down is a hardware reset. Reset redefines the SFRs but does not change the on-chip RAM. The reset should not be activated before VCC is restored to its normal operating level and must be held active long enough to allow the oscillator to restart and stabilize.
29
Very compact and light Low power consumption No geometric distortion Little or no flicker depending on backlight technology Not affected by screen burn-in No high voltage or other hazards present during repair/service Can be made in almost any size or shape No theoretical resolution limit
LCD Background:
Frequently, an 8051 program must interact with the outside world using input and output devices that communicate directly with a human being. One of the most common devices attached to an 8051 is an LCD display. Some of the most common LCDs connected to the 8051 are 16x2 and 20x2 displays. This means 16 characters per line by 2 lines and 20 characters per line by 2 lines, respectively.
Fortunately, a very popular standard exists which allows us to communicate with the vast majority of LCDs regardless of their manufacturer. The standard is referred to as HD44780U, which refers to the controller chip which receives data from an external source (in this case, the 8051) and communicates directly with the LCD.
30
44780 LCD BACKGROUND The 44780 standard requires 3 control lines as well as either 4 or 8 I/O lines for the data bus. The user may select whether the LCD is to operate with a 4-bit data bus or an 8-bit data bus. If a 4-bit data bus is used the LCD will require a total of 7 data lines (3 control lines plus the 4 lines for the data bus). If an 8-bit data bus is used the LCD will require a total of 11 data lines (3 control lines plus the 8 lines for the data bus).
The three control lines are referred to as EN, RS, and RW.
31
The EN line is called "Enable." This control line is used to tell the LCD that you are sending it data. To send data to the LCD, your program should make sure this line is low (0) and then set the other two control lines and/or put data on the data bus. When the other lines are completely ready, bring EN high (1) and wait for the minimum amount of time required by the LCD datasheet (this varies from LCD to LCD), and end by bringing it low (0) again. The RS line is the "Register Select" line. When RS is low (0), the data is to be treated as a command or special instruction (such as clear screen, position cursor, etc.). When RS is high (1), the data being sent is text data which should be displayed on the screen. For example, to display the letter "T" on the screen you would set RS high. The RW line is the "Read/Write" control line. When RW is low (0), the information on the data bus is being written to the LCD. When RW is high (1), the program is effectively querying (or reading) the LCD. Only one instruction ("Get LCD status") is a read command. All others are write commands--so RW will almost always be low .Finally, the data bus consists of 4 or 8 lines (depending on the mode of operation selected by the user). In the case of an 8-bit data bus, the lines are referred to as DB0, DB1, DB2, DB3, DB4, DB5, DB6, and DB7.
4.6 ADC0808
Features Easy interface to all microprocessors Operates ratio metrically or with 5 VDC or analog span adjusted voltage reference No zero or full-scale adjust required 8-channel multiplexer with address logic 0V to 5V input range with single 5V power supply Outputs meet TTL voltage level specifications Standard hermetic or molded 28-pin DIP package 28-pin molded chip carrier package ADC0808 equivalent to MM74C949 ADC0809 equivalent to MM74C949-1
32
Key Specifications Resolution 8 Bits Total Unadjusted Error 12 LSB and 1 LSB Single Supply 5 VDC Low Power 15 mW Conversion Time 100 s
33
The ADC0808, ADC0809 data acquisition component is a monolithic CMOS device with an 8-bit analog-to-digital converter, 8-channel multiplexer and microprocessor compatible control logic. The 8-bit A/D converter uses successive approximation as the conversion technique. The converter features a high impedance chopper stabilized comparator, a 256R voltage divider with analog switch tree and a successive approximation register.
Fig 4.6 ADC0808 The 8-channel multiplexer can directly access any of 8-single-ended analog signals. The device eliminates the need for external zero and full-scale adjustments. Easy interfacing to microprocessors is provided by the latched and decoded multiplexer address inputs and latched TTL TRI-STATE outputs. The design of the ADC0808, ADC0809 has been optimized by incorporating the most desirable aspects of several A/D conversion techniques. The ADC0808, ADC0809 offers high speed, high accuracy, minimal temperature dependence, excellent longterm accuracy and repeatability, and consumes minimal power. These features make this device ideally suited to applications from process and machine control to consumer and automotive applications. The ADC0808/ADC0809 Data Acquisition Devices (DAD) implement on a single chip most the elements of the standard data acquisition system. They contain an 8-bit A/D Converter, 8-channel multiplexer with an address input latch, and associated control logic. These devices
34
provide most of the logic to interface to a variety of microcontrollers with the addition of a minimum number of parts. These circuits are implemented using a standard metal-gate CMOS process. This process is particularly suitable to applications. Where both analog and digital functions must be implemented on the same chip. These two converters, the ADC0808 and ADC0809, are functionally identical except that the ADC0808 has a total unadjusted error of 12 LSB and the ADC0809 has an unadjusted error of 1 LSB. All these converters will typically do a conversion in100 s when using a 640 kHz clock, but can convert a single input in as little as 50 s.
Functional Description The ADC0808/ADC0809, shown in the above figure, can be functionally divided into 2 basic sub circuits. These two sub circuits are an analog multiplexer and an A/D converter. The multiplexer uses 8 standard CMOS analog switches to provide for up to 8 analog inputs. The switches are selectively turned on, depending on the data latched into a 3-bit multiplexer address register. The second function block, the successive approximation A/D converter, transforms the analog output of the multiplexer to an 8-bit digital word. The output of the multiplexer goes to one of two comparator inputs. The other input is derived from a 256R resistor ladder, which is tapped by a MOSFET transistor switch tree. The converter control logic controls the switch tree,
35
funneling a particular tap voltage to the comparator. Based on the result of this comparison, the control logic and the successive approximation register (SAR) will decide whether the next tap to be selected should be higher or lower than the present tap on the resistor ladder. This algorithm is executed 8 times per conversion, once every 8 clock periods, yielding a total conversion time of 64 clock periods. When the conversion cycle is complete the resulting data is loaded into the TRI-STATE output latch. The data in the output latch can then be read by the host system any time before the end of the next conversion. The TRI-STATE capability of the latch allows easy interface to bus oriented systems. The operation of these converters by a microprocessor or some control logic is very simple. The controlling device first selects the desired input channel. To do this, a 3-bit channel address is placed on the A, B, C input pins; and the ALE input is pulsed positively, clocking the address into the multiplexer address register. To begin the conversion, the START pin is pulsed. On the rising edge of this pulse the internal registers are cleared and on the falling edge the start conversion initiated. There are 8 clock periods per approximation. Even though there is no conversion in progress the ADC0808/ADC0809 is still internally cycling through these 8 clock periods. A start pulse can occur any time during this cycle but the conversion will not actually begin until the converter internally cycles to the beginning of the next 8 clock period sequence. As long as the start pin is held high no conversion begins, but when the start pin is taken low the conversion will start within 8 clock periods. The EOC output is triggered on the rising edge of the start pulse. It, too, is controlled by the 8 clock period cycle, so it will go low within 8 clock periods of the rising edge of the start pulse. One can see that it is entirely possible for EOC to go low before the conversion starts internally, but this is not important, since the positive transition of EOC, which occurs at the end of a conversion, is what the control logic is looking for. Once EOC does go high this signals the interface logic that the data resulting from the conversion is ready to be read. The output enable (OE) is then raised high. This enables the TRISTATE outputs, allowing the data to be read.
36
communication timing. It should be connected to any TTL/CMOS logic serial RXD and TXD lines and can support baud-rate of 9600bps, 19200bps, 38400bps and 57600bps. It also supports 4 unique RF channel selections to reduce congestions on the same channel during peer-to-peer communication.
37
Pin-out Info Pin 1- Ground Pin 2- VCC (4.25V to 12.0V regulated power) Pin 3- Transmit Serial Data Output from Module (3.3V TTL) Pin 4- Receive Serial Data Input from External Device (3.3V to 5V TTL) Baud Jumper Info Default No Baud Jumper 9600bps Baud 1 Jumper 19200bps Baud 2 Jumper 38400bps Baud 1 & Baud 2 Jumper 57600bps Freq Jumper Info Default No Freq Jumper 2433MHz Freq 1 Jumper 2438MHz Freq 2 Jumper 2443MHz Freq 1 & Freq 2 Jumper 2450MHz LED Info PWR LED power supply present TX LED RF transmission of data RX LED RF reception of data
Features
No configuration needed for out-of-the-box RF communications Standard Serial Communication Socket for easy integration Fast 250 kbps RF air-data rate to the end node 2.4 GHz for worldwide deployment Baud-rate selection and channel frequency selection Up to 100meters outdoor open air node-to-node range
Applications
Wireless telemetry for transmitting sensor data Remote control applications with fast response requirements Wireless Home Networking applications Point-to-point and point-to-multipoint network topologies Wireless mouse, wireless keyboard and other wireless user interface devices Wireless data logging applications
38
Audience response systems UAV communication and control Swarm Robotics Wireless Audio transmission applications
4.10 RELAY
A relay is an electrically operated switch. Many relays use an electromagnet to operate a switching mechanism mechanically, but other operating principles are also used. Relays are used where it is necessary to control a circuit by a low-power signal (with complete electrical isolation between control and controlled circuits), or where several circuits must be controlled by one signal.
A relay is an electrically operated switch. Current flowing through the coil of the relay creates a magnetic field which attracts a lever and changes the switch contacts. The coil current can be on or off so relays have two switch positions and most have double throw (changeover) switch contacts as shown in the diagram.
39
Relays allow one circuit to switch a second circuit which can be completely separate from the first. For example a low voltage battery circuit can use a relay to switch a 230V AC mains circuit. There is no electrical connection inside the relay between the two circuits; the link is magnetic and mechanical.
The coil of a relay passes a relatively large current, typically 30mA for a 12V relay, but it can be as much as 100mA for relays designed to operate from lower voltages. Most ICs (chips) cannot provide this current and a transistor is usually used to amplify the small IC current to the larger value required for the relay coil. The maximum output current for the popular 555 timer IC is 200mA so these devices can supply relay coils directly without amplification.
Relays are usually SPDT or DPDT but they can have many more sets of switch contacts, for example relays with 4 sets of changeover contacts are readily available. For further information about switch contacts and the terms used to describe them please see the page on switches.
Most relays are designed for PCB mounting but you can solder wires directly to the pins providing you take care to avoid melting the plastic case of the relay.
The supplier's catalogue should show you the relay's connections. The coil will be obvious and it may be connected either way round. Relay coils produce brief high voltage 'spikes' when they are switched off and this can destroy transistors and ICs in the circuit. To prevent damage you must connect a protection diode across the relay coil.
The figure shows a relay with its coil and switch contacts. You can see a lever on the left being attracted by magnetism when the coil is switched on. This lever moves the switch contacts.
40
There is one set of contacts (SPDT) in the foreground and another behind them, making the relay DPDT. The relay's switch connections are usually labelled COM, NC and NO:
COM = Common, always connect to this; it is the moving part of the switch. NC = Normally Closed, COM is connected to this when the relay coil is off. NO = Normally Open, COM is connected to this when the relay coil is on.
41
Applications of relays
Relays are used to and for:
Control a high-voltage circuit with a low-voltage signal, as in some types of modems or audio amplifiers.
Control a high-current circuit with a low-current signal, as in the starter solenoid of an automobile.
Detect and isolate faults on transmission and distribution lines by opening and closing circuit breakers.
Time delay functions. Relays can be modified to delay opening or delay closing a set of contacts. A very short (a fraction of a second) delay would use a copper disk between the armature and moving blade assembly. Current flowing in the disk maintains magnetic field for a short time, lengthening release time. For a slightly longer (up to a minute) delay, a dashpot is used. A dashpot is a piston filled with fluid that is allowed to escape slowly. The time period can be varied by increasing or decreasing the flow rate. For longer time periods, a mechanical clockwork timer is installed.
n Nonlinearity only 14C typical n Low impedance output, 0.1 for 1 mA load
The LM35 series are precision integrated-circuit temperature sensors, whose output voltage is linearly proportional to the Celsius (Centigrade) temperature. The LM35 thus has an advantage over linear temperature sensors calibrated in Kelvin, as the user is not required to subtract a large constant voltage from its output to obtain convenient
Centigrade scaling. The LM35 does not require any external calibration or trimming to provide typical accuracies of 14C at room temperature and 34C over a full 55 to +150C temperature range. Low cost is assured by trimming and calibration at the wafer level. The LM35s low output impedance, linear output, and precise inherent calibration make interfacing to readout or control circuitry especially easy. It can be used with single power supplies, or with plus and minus supplies. As it draws only 60 A from its supply, it has very low selfheating, less than 0.1C in still air. The LM35 is rated to operate over a 55 to +150C temperature range, while the LM35C is rated for a 40 to +110C range (10 with improved accuracy). The LM35 series is available packaged in hermetic TO-46 transistor packages, while the LM35C, LM35CA, and LM35D are also available in the plastic TO-92 transistor package. The LM35D is also avail- able in an 8-lead surface mount small outline package and a plastic TO-220 package.
Applications: The LM35 can be applied easily in the same way as other integrated circuit temperature sensors. It can be glued or cemented to a surface and its temperature will be within about 0.01C of the surface temperature.
43
This presumes that the ambient air temperature is almost the same as the surface temperature; if the air temperature were much higher or lower than the surface temperature, the actual temperature of the LM35 die would be at an intermediate temperature between the surface temperature and the air temperature. This is especially true for the TO-92 plastic package, where the copper leads are the principal thermal path to carry heat into the device, so its temperature might be closer to the air temperature than to the surface temperature.
To minimize this problem, be sure that the wiring to the LM35, as it leaves
the device, is held at the same temperature as the surface of interest. The easiest way to do this is to cover up these wires with a bead of epoxy which will insure that the leads and wires are all at the same temperature as the surface, and that the LM35 dies temperature will not be affected by the air temperature.
4.12 LED
A light-emitting diode (LED) is a semiconductor light source. LEDs are used as indicator lamps in many devices, and are increasingly used for lighting. When a light-emitting diode is forward biased (switched on), electrons are able to recombine with holes within the device, releasing energy in the form of photons. This effect is called electroluminescence and the color of the light (corresponding to the energy of the photon) is determined by the energy gap of the semiconductor. An LED is often small in area (less than 1 mm2), and integrated optical components may be used to shape its radiation pattern. LEDs present many advantages over incandescent light sources including lower energy consumption, longer lifetime, improved robustness, smaller size, faster switching, and greater durability and reliability.
44
Types of LEDS
Light-emitting diodes are used in applications as diverse as replacements for aviation lighting, automotive lighting as well as in traffic signals. The compact size, the possibility of narrow bandwidth, switching speed, and extreme reliability of LEDs has allowed new text and video displays and sensors to be developed, while their high switching rates are also useful in advanced communications technology.
Electronic Symbol:
Fig 4.12(b): symbol of LED Colors and materials of LEDS Conventional LEDs are made from a variety of inorganic semiconductor materials, the following table shows the available colors with wavelength range, voltage drop and material.
White LEDS Light Emitting Diodes (LED) have recently become available that are both white and bright, so bright that they seriously compete with incandescent lamps in lighting applications. They are still pretty expensive as compared to a GOW lamp but draw much less current and project a fairly well focused beam.
45
When run within their ratings, they are more reliable than lamps as well. Red LEDs are now being used in automotive and truck tail lights and in red traffic signal lights. You will be able to detect them because they look like an array of point sources and they go on and off instantly as compared to conventional incandescent lamps.
LEDs are monochromatic (one color) devices. The color is determined by the band gap of the semiconductor used to make them. Red, green, yellow and blue LEDs are fairly common. White light contains all colors and cannot be directly created by a single LED. The most common form of "white" LED really isn't white. It is a Gallium Nitride blue LED coated with a phosphor that, when excited by the blue LED light, emits a broad range spectrum that in addition to the blue emission, makes a fairly white light. There is a claim that these white LED's have a limited life. After 1000 hours or so of operation, they tend to yellow and dim to some extent. Running the LEDs at more than their rated current will certainly accelerate this process. There are two primary ways of producing high intensity white-light using LEDs. One is to use individual LEDs that emit three primary coloursred, green, and blueand then mix all the colours to form white light. The other is to use a phosphor material to convert monochromatic light from a blue or UV LED to broad-spectrum white light, much in the same way a fluorescent light bulb works. Due to metamerism, it is possible to have quite different spectra that appear white.
4.13 IN4007
46
Diodes are used to convert AC into DC these are used as half wave rectifier or full wave rectifier. Three points must he kept in mind while using any type of diode. 1. Maximum forward current capacity 2. Maximum reverse voltage capacity 3. Maximum forward voltage capacity
Diodes of number IN4001, IN4002, IN4003, IN4004, IN4005, IN4006 and IN4007 have maximum reverse bias voltage capacity of 50V and maximum forward current capacity of 1 Amp.
Diode of same capacities can be used in place of one another. Besides this diode of more capacity can be used in place of diode of low capacity but diode of low capacity cannot be used in place of diode of high capacity. For example, in place of IN4002; IN4001 or IN4007 can be used but IN4001 or IN4002 cannot be used in place of IN4007.The diode BY125made by company BEL is equivalent of diode from IN4001 to IN4003. BY 126 is equivalent to diodes IN4004 to 4006 and BY 127 is equivalent to diode IN4007.
47
PN JUNCTION OPERATION Now that you are familiar with P- and N-type materials, how these materials are joined together to form a diode, and the function of the diode, let us continue our discussion with the operation of the PN junction. But before we can understand how the PN junction works, we must first consider current flow in the materials that make up the junction and what happens initially within the junction when these two materials are joined together.
repelled by the negative side of the battery and move through the crystal toward the positive side of the battery.
4.14 RESISTORS
A resistor is a two-terminal electronic component designed to oppose an electric current by producing a voltage drop between its terminals in proportion to the current, that is, in accordance with Ohm's law: V = IR Resistors are used as part of electrical networks and electronic circuits. They are extremely commonplace in most electronic equipment. Practical resistors can be made of various compounds and films, as well as resistance wire (wire made of a high-resistivity alloy, such as nickel/chrome). The primary characteristics of resistors are their resistance and the power they can dissipate. Other characteristics include temperature coefficient, noise, and inductance. Less wellknown is critical resistance, the value below which power dissipation limits the maximum permitted current flow, and above which the limit is applied voltage. Critical resistance depends upon the materials constituting the resistor as well as its physical dimensions; it's determined by design. Resistors can be integrated into hybrid and printed circuits, as well as integrated circuits. Size, and position of leads (or terminals) are relevant to equipment designers; resistors must be physically large enough not to overheat when dissipating their power.
49
A resistor is a two-terminal passive electronic component which implements electrical resistance as a circuit element. When a voltage V is applied across the terminals of a resistor, a current I will flow through the resistor in direct proportion to that voltage. The reciprocal of the constant of proportionality is known as the resistance R, since, with a given voltage V, a larger value of R further "resists" the flow of current I as given by Ohm's law:
Resistors are common elements of electrical networks and electronic circuits and are ubiquitous in most electronic equipment. Practical resistors can be made of various compounds and films, as well as resistance wire (wire made of a high-resistivity alloy, such as nickelchrome). Resistors are also implemented within integrated circuits, particularly analog devices, and can also be integrated into hybrid and printed circuits. The electrical functionality of a resistor is specified by its resistance: common commercial resistors are manufactured over a range of more than 9 orders of magnitude. When specifying that resistance in an electronic design, the required precision of the resistance may require attention to the manufacturing tolerance of the chosen resistor, according to its specific application. The temperature coefficient of the resistance may also be of concern in some precision applications. Practical resistors are also specified as having a maximum power rating which must exceed the anticipated power dissipation of that resistor in a particular circuit: this is mainly of concern in power electronics applications. Resistors with higher power ratings are physically larger and may require heat sinking. In a high voltage circuit, attention must sometimes be paid to the rated maximum working voltage of the resistor. The series inductance of a practical resistor causes its behavior to depart from ohms law; this specification can be important in some high-frequency applications for smaller values of
50
resistance. In a low-noise amplifier or pre-amp the noise characteristics of a resistor may be an issue. The unwanted inductance, excess noise, and temperature coefficient are mainly dependent on the technology used in manufacturing the resistor. They are not normally specified individually for a particular family of resistors manufactured using a particular technology. A family of discrete resistors is also characterized according to its form factor, that is, the size of the device and position of its leads (or terminals) which is relevant in the practical manufacturing of circuits using them. Units The ohm (symbol: ) is the SI unit of electrical resistance, named after Georg Simon Ohm. An ohm is equivalent to a volt per ampere. Since resistors are specified and manufactured over a very large range of values, the derived units of milliohm (1 m = 103 ), kilohm (1 k = 103 ), and megohm (1 M = 106 ) are also in common usage. The reciprocal of resistance R is called conductance G = 1/R and is measured in Siemens (SI unit), sometimes referred to as a mho. Thus a Siemens is the reciprocal of an ohm: S = 1. Although the concept of conductance is often used in circuit analysis, practical resistors are always specified in terms of their resistance (ohms) rather than conductance.
VARIABLE RESISTORS
Adjustable resistors
A resistor may have one or more fixed tapping points so that the resistance can be changed by moving the connecting wires to different terminals. Some wire wound power resistors have a tapping point that can slide along the resistance element, allowing a larger or smaller part of the resistance to be used. Where continuous adjustment of the resistance value during operation of equipment is required, the sliding resistance tap can be connected to a knob accessible to an operator. Such a device is called a rheostat and has two terminals.
Potentiometer A potentiometer is a manually adjustable resistor. The way this device works is relatively simple. One terminal of the potentiometer is connected to a power source. Another is hooked up to ground (a point with no voltage or resistance and which serves as a neutral reference point), while the third
51
terminal runs across a strip of resistive material. This resistive strip generally has a low resistance at one end; its resistance gradually increases to a maximum resistance at the other end. The third terminal serves as the connection between the power source and ground, and is usually interfaced to the user by means of a knob or lever. The user can adjust the position of the third terminal along the resistive strip in order to manually increase or decrease resistance. By controlling resistance, a potentiometer can determine how much current flow through a circuit. When used to regulate current, the potentiometer is limited by the maximum resistivity of the strip.
The power of this simple device is not to be underestimated. In most analog devices, a potentiometer is what establishes the levels of output. In a loud speaker, for example, a potentiometer directly adjusts volume; in a television monitor, it controls brightness.
A potentiometer can also be used to control the potential difference, or voltage, across a circuit. The setup involved in utilizing a potentiometer for this purpose is a little bit more complicated. It involves two circuits: the first circuit consists of a cell and a resistor. At one end, the cell is connected in series to the second circuit, and at the other end it is connected to a potentiometer in parallel with the second circuit. The potentiometer in this arrangement drops the voltage by an amount equal to the ratio between the resistance allowed by the position of the third terminal and the highest possible resistivity of the strip. In other words, if the knob controlling the resistance is positioned at the exact halfway point on the resistive strip, then the output voltage will drop by exactly fifty percent, no matter how high the potentiometer's input voltage. Unlike with current regulation, voltage regulation is not limited by the maximum resistivity of the strip
4.15 CAPACITORS
52
A capacitor or condenser is a passive electronic component consisting of a pair of conductors separated by a dielectric. When a voltage potential difference exists between the conductors, an electric field is present in the dielectric. This field stores energy and produces a mechanical force between the plates. The effect is greatest between wide, flat, parallel, narrowly separated conductors. An ideal capacitor is characterized by a single constant value, capacitance, which is measured in farads. This is the ratio of the electric charge on each conductor to the potential difference between them. In practice, the dielectric between the plates passes a small amount of leakage current. The conductors and leads introduce an equivalent series resistance and the dielectric has an electric field strength limit resulting in a breakdown voltage. The properties of capacitors in a circuit may determine the resonant frequency and quality factor of a resonant circuit, power dissipation and operating frequency in a digital logic circuit, energy capacity in a high-power system, and many other important aspects.
A capacitor (formerly known as condenser) is a device for storing electric charge. The forms of practical capacitors vary widely, but all contain at least two conductors separated by a non-conductor. Capacitors used as parts of electrical systems, for example, consist of metal foils separated by a layer of insulating film. Capacitors are widely used in electronic circuits for blocking direct current while allowing alternating current to pass, in filter networks, for smoothing the output of power supplies, in the resonant circuits that tune radios to particular frequencies and for many other purposes.
53
A capacitor is a passive electronic component consisting of a pair of conductors separated by a dielectric (insulator). When there is a potential difference (voltage) across the conductors, a static electric field develops in the dielectric that stores energy and produces a mechanical force between the conductors. An ideal capacitor is characterized by a single constant value, capacitance, measured in farads. This is the ratio of the electric charge on each conductor to the potential difference between them. The capacitance is greatest when there is a narrow separation between large areas of conductor, hence capacitor conductors are often called "plates", referring to an early means of construction. In practice the dielectric between the plates passes a small amount of leakage current and also has an electric field strength limit, resulting in a breakdown voltage, while the conductors and leads introduce an undesired inductance and resistance.
Charge separation in a parallel-plate capacitor causes an internal electric field. A dielectric (orange) reduces the field and increases the capacitance.
54
A simple demonstration of a parallel-plate capacitor A capacitor consists of two conductors separated by a non-conductive region. The nonconductive region is called the dielectric or sometimes the dielectric medium. In simpler terms, the dielectric is just an electrical insulator. Examples of dielectric mediums are glass, air, paper, vacuum, and even a semiconductor depletion region chemically identical to the conductors. A capacitor is assumed to be self-contained and isolated, with no net electric charge and no influence from any external electric field. The conductors thus hold equal and opposite charges on their facing surfaces, and the dielectric develops an electric field. In SI units, a capacitance of one farad means that one coulomb of charge on each conductor causes a voltage of one volt across the device. The capacitor is a reasonably general model for electric fields within electric circuits. An ideal capacitor is wholly characterized by a constant capacitance C, defined as the ratio of charge Q on each conductor to the voltage V between them:
Sometimes charge build-up affects the capacitor mechanically, causing its capacitance to vary. In this case, capacitance is defined in terms of incremental changes:
Energy storage Work must be done by an external influence to "move" charge between the conductors in a capacitor. When the external influence is removed the charge separation persists in the electric field and energy is stored to be released when the charge is allowed to return to its equilibrium position. The work done in establishing the electric field, and hence the amount of energy stored, is given by:
Current-voltage relation The current i(t) through any component in an electric circuit is defined as the rate of flow of a charge q(t) passing through it, but actual charges, electrons, cannot pass through the dielectric
55
layer of a capacitor, rather an electron accumulates on the negative plate for each one that leaves the positive plate, resulting in an electron depletion and consequent positive charge on one electrode that is equal and opposite to the accumulated negative charge on the other. Thus the charge on the electrodes is equal to the integral of the current as well as proportional to the voltage as discussed above. As with any ant derivative, a constant of integration is added to represent the initial voltage v (t0). This is the integral form of the capacitor equation,
. Taking the derivative of this, and multiplying by C, yields the derivative form,
. The dual of the capacitor is the inductor, which stores energy in the magnetic field rather than the electric field. Its current-voltage relation is obtained by exchanging current and voltage in the capacitor equations and replacing C with the inductance L. DC circuits RC circuit
A simple resistor-capacitor circuit demonstrates charging of a capacitor. A series circuit containing only a resistor, a capacitor, a switch and a constant DC source of voltage V0 is known as a charging circuit. If the capacitor is initially uncharged while the switch is open, and the switch is closed at t = 0, it follows from Kirchhoff's voltage law that
56
At t = 0, the voltage across the capacitor is zero and the voltage across the resistor is V0. The initial current is then i (0) =V0 /R. With this assumption, the differential equation yields
where 0 = RC is the time constant of the system. As the capacitor reaches equilibrium with the source voltage, the voltage across the resistor and the current through the entire circuit decay exponentially. The case of discharging a charged capacitor likewise demonstrates exponential decay, but with the initial capacitor voltage replacing V0 and the final voltage being zero. AC circuits See also: reactance (electronics) and electrical impedance deriving the device specific impedances Impedance, the vector sum of reactance and resistance, describes the phase difference and the ratio of amplitudes between sinusoidally varying voltage and sinusoidally varying current at a given frequency. Fourier analysis allows any signal to be constructed from a spectrum of frequencies, whence the circuit's reaction to the various frequencies may be found. The reactance and impedance of a capacitor are respectively
where j is the imaginary unit and is the angular velocity of the sinusoidal signal. The - j phase indicates that the AC voltage V = Z I lags the AC current by 90: the positive current phase corresponds to increasing voltage as the capacitor charges; zero current corresponds to instantaneous constant voltage, etc. Note that impedance decreases with increasing capacitance and increasing frequency. This implies that a higher-frequency signal or a larger capacitor results in a lower voltage amplitude per current amplitudean AC "short circuit" or AC coupling. Conversely, for very low
57
frequencies, the reactance will be high, so that a capacitor is nearly an open circuit in AC analysisthose frequencies have been "filtered out". Capacitors are different from resistors and inductors in that the impedance is inversely proportional to the defining characteristic, i.e. capacitance. Parallel plate model
Dielectric is placed between two conducting plates, each of area A and with a separation of d. The simplest capacitor consists of two parallel conductive plates separated by a dielectric with permittivity (such as air). The model may also be used to make qualitative predictions for other device geometries. The plates are considered to extend uniformly over an area A and a charge density = Q/A exists on their surface. Assuming that the width of the plates is much greater than their separation d, the electric field near the centre of the device will be uniform with the magnitude E = /. The voltage is defined as the line integral of the electric field between the plates
Solving this for C = Q/V reveals that capacitance increases with area and decreases with separation . The capacitance is therefore greatest in devices made from materials with a high permittivity.
58
Several capacitors in parallel. Networks See also: Series and parallel circuits For capacitors in parallel Capacitors in a parallel configuration each have the same applied voltage. Their capacitances add up. Charge is apportioned among them by size. Using the schematic diagram to visualize parallel plates, it is apparent that each capacitor contributes to the total surface area.
Several capacitors in series. Connected in series, the schematic diagram reveals that the separation distance, not the plate area, adds up. The capacitors each store instantaneous charge build-up equal to that of every other capacitor in the series. The total voltage difference from end to end is apportioned to each capacitor according to the inverse of its capacitance. The entire series acts as a capacitor smaller than any of its components.
Capacitors are combined in series to achieve a higher working voltage, for example for smoothing a high voltage power supply. The voltage ratings, which are based on plate separation, add up. In such an application, several series connections may in turn be
59
connected in parallel, forming a matrix. The goal is to maximize the energy storage utility of each capacitor without overloading it. Series connection is also used to adapt electrolytic capacitors for AC use. Non-ideal behaviour Capacitors deviate from the ideal capacitor equation in a number of ways. Some of these, such as leakage current and parasitic effects are linear, or can be assumed to be linear, and can be dealt with by adding virtual components to the equivalent circuit of the capacitor. The usual methods of network analysis can then be applied. In other cases, such as with breakdown voltage, the effect is non-linear and normal (i.e., linear) network analysis cannot be used, the effect must be dealt with separately. There is yet another group, which may be linear but invalidate the assumption in the analysis that capacitance is a constant. Such an example is temperature dependence. Breakdown voltage Main article: Breakdown voltage Above a particular electric field, known as the dielectric strength Eds, the dielectric in a capacitor becomes conductive. The voltage at which this occurs is called the breakdown voltage of the device, and is given by the product of the dielectric strength and the separation between the conductors, Vbd = Edsd
The maximum energy that can be stored safely in a capacitor is limited by the breakdown voltage. Due to the scaling of capacitance and breakdown voltage with dielectric thickness, all capacitors made with a particular dielectric have approximately equal maximum energy density, to the extent that the dielectric dominates their volume. For air dielectric capacitors the breakdown field strength is of the order 2 to 5 MV/m; for mica the breakdown is 100 to 300 MV/m, for oil 15 to 25 MV/m, and can be much less when other materials are used for the dielectric. The dielectric is used in very thin layers and so absolute breakdown voltage of capacitors is limited. Typical ratings for capacitors used for general electronics applications range from a few volts to 100V or so. As the voltage increases, the dielectric must be thicker, making high-voltage capacitors larger than those rated for lower voltages. The breakdown voltage is critically affected by factors such as the geometry of the capacitor conductive parts; sharp edges or points increase the electric field strength at that point and can lead to a local breakdown. Once this starts to happen, the breakdown will quickly "track"
60
through the dielectric till it reaches the opposite plate and cause a short circuit. The usual breakdown route is that the field strength becomes large enough to pull electrons in the dielectric from their atoms thus causing conduction. Other scenarios are possible, such as impurities in the dielectric, and, if the dielectric is of a crystalline nature, imperfections in the crystal structure can result in an avalanche breakdown as seen in semi-conductor devices. Breakdown voltage is also affected by pressure, humidity and temperature. Equivalent circuit
Two different circuit models of a real capacitor An ideal capacitor only stores and releases electrical energy, without dissipating any. In reality, all capacitors have imperfections within the capacitor's material that create resistance. This is specified as the equivalent series resistance or ESR of a component. This adds a real component to the impedance:
As frequency approaches infinity, the capacitive impedance (or reactance) approaches zero and the ESR becomes significant. As the reactance becomes negligible, power dissipation approaches PRMS = VRMS /RESR. Similarly to ESR, the capacitor's leads add equivalent series inductance or ESL to the component. This is usually significant only at relatively high frequencies. As inductive reactance is positive and increases with frequency, above a certain frequency capacitance will be canceled by inductance. High-frequency engineering involves accounting for the inductance of all connections and components.
61
If the conductors are separated by a material with a small conductivity rather than a perfect dielectric, then a small leakage current flows directly between them. The capacitor therefore has a finite parallel resistance, and slowly discharges over time (time may vary greatly depending on the capacitor material and quality).
62
5. SOFTWARE REQUIREMENTS
63
64
The Keil ARM tool kit includes three main tools, assembler, compiler and linker. An assembler is used to assemble the ARM assembly program. A compiler is used to compile the C source code into an object file. A linker is used to create an absolute object module suitable for our in-circuit emulator.
65
Project1. Vision2 creates a new project file with the name PROJECT1.UV2 which contains a default target and file group name. You can see these names in the Project.
After you have tested your application, it is required to create an Intel HEX file to download the software into an EPROM programmer or simulator. Vision2 creates HEX files with each build process when Create HEX files under Options for Target Output is enabled. You may start your PROM programming utility after the make process when you specify the program under the option Run User Program #1.
You have made when you create your project target. Refer to page 58 for more Information about selecting a device. You may select and display the on-chip peripheral components using the Debug menu. You can also change the aspects of each peripheral using the controls in the dialog boxes.
68
debugging. Numerous example programs are included to help you get started with the most popular embedded 8051 devices. The Keil Vision Debugger accurately simulates on-chip peripherals (IC, CAN, UART, SPI, Interrupts, I/O Ports, A/D Converter, D/A Converter, and PWM Modules) of your 8051 device. Simulation helps you understand hardware configurations and avoids time wasted on setup problems. Additionally, with simulation, you can write and test applications before target hardware is available.
5.15 EMBEDDED C
Use of embedded processors in passenger cars, mobile phones, medical equipment, aerospace systems and defense systems is widespread, and even everyday domestic appliances such as dish washers, televisions, washing machines and video recorders now include at least one such device. Because most embedded projects have severe cost constraints, they tend to use low-cost processors like the 8051 family of devices considered in this book. These popular chips have very limited resources available most such devices have around 256 bytes (not megabytes!) of RAM, and the available processor power is around 1000 times less than that of a desktop processor. As a result, developing embedded software presents significant new challenges, even for experienced desktop programmers. If you have some programming experience - in C, C++ or Java - then this book and its accompanying CD will help make your move to the embedded world as quick and painless as possible.
6. SCHEMATIC DIAGRAM
69
70
ATMEL series of 8051 family of micro controllers need certain standard connections. The actual number of the Microcontroller could be 89C51 , 89C52, 89S51, 89S52, and as regards to 20 pin configuration a number of 89C2051. The 4 set of I/O ports are used based on the project requirement. Every microcontroller requires a timing reference for its internal program execution therefore an oscillator needs to be functional with a desired frequency to obtain the timing reference as t =1/f. A crystal ranging from 2 to 20 MHz is required to be used at its pin number 18 and 19 for the internal oscillator. It may be noted here the crystal is not to be understood as crystal oscillator It is just a crystal, while connected to the appropriate pin of the microcontroller it results in oscillator function inside the microcontroller. Typically 11.0592 MHz crystal is used in general for most of the circuits using 8051 series microcontroller. Two small value ceramic capacitors of 33pF each is used as a standard connection for the crystal as shown in the circuit diagram.
RESET
Pin no 9 is provided with an resset arrangement by a combination of an electrolytic capacitor and a register forming RC time constant. At the time of switch on, the capacitor gets charged, and it behaves as a full short circuit from the positive to the pin number 9. After the capacitor gets fully charged the current stops flowing and pin number 9 goes low which is pulled down by a 10k resistor to the ground. This arrangement of reset at pin 9 going high initially and then to logic 0 i.e., low helps the program execution to start from the beginning. In absence of this the program execution could have taken place arbitrarily anywhere from the program cycle. A pushbutton switch is connected across the capacitor so that at any given time as desired it can be pressed such that it discharges the capacitor and while released the capacitor starts charging again and then pin number 9 goes to high and then back to low, to enable the program execution from the beginning. This operation of high to low of the reset pin takes place in fraction of a second as decided by the time constant R and C. For example: A 10F capacitor and a 10k resistor would render a 100ms time to pin number 9 from logic high to low, there after the pin number 9 remains low.
71
External Access(EA): Pin no 31 of 40 pin 8051 microcontroller termed as EA is required to be connected to 5V for accessing the program form the on-chip program memory. If it is connected to ground then the controller accesses the program from external memory. However as we are using the internal memory it is always connected to +5V.
8. BILL OF MATERIALS
72
9. CODING
73
3. 4.
Click on the Project menu from the title bar Then Click on New Project
74
5.
Save the Project by typing suitable project name with no extension in u r own folder sited in either C:\ or D:\
6. 7. 8.
Then Click on save button above. Select the component for u r project. i.e. Atmel Click on the + Symbol beside of Atmel
9.
10. 11.
12.
13. 14.
Now your project is ready to USE. Now double click on the Target1, you would get another option Source group 1 as shown in next page.
15.
Click on the file option from menu bar and select new.
16.
The next screen will be as shown in next page, and just maximize it by double clicking on its blue boarder.
77
17. 18.
Now start writing program in either in EMBEDDED C or ASM. For a program written in Assembly, then save it with extension . asm and for EMBEDDED C based program save it with extension .C
19.
Now right click on Source group 1 and click on Add files to Group Source.
78
20.
Now you will get another window, on which by default EMBEDDED C files will appear.
Now select as per your file extension given while saving the file Click only one time on option ADD. Now Press function key F7 to compile. Any error will appear if so happen.
79
24. 25.
If the file contains no error, then press Control+F5 simultaneously. The new window is as follows
26. 27.
Then Click OK. Now click on the Peripherals from menu bar, and check your required port as shown in fig below.
80
28.
29. 30.
Now keep Pressing function key F11 slowly and observe. You are running your program successfully.
81
10 .HARDWARE TESTING
10.1 CONTINUITY TEST:
In electronics, a continuity test is the checking of an electric circuit to see if current flows (that it is in fact a complete circuit). A continuity test is performed by placing a small voltage (wired in series with an LED or noise-producing component such as a piezoelectric speaker) across the chosen path. If electron flow is inhibited by broken conductors, damaged components, or excessive resistance, the circuit is "open". Devices that can be used to perform continuity tests include multi meters which measure current and specialized continuity testers which are cheaper, more basic devices, generally with a simple light bulb that lights up when current flows. An important application is the continuity test of a bundle of wires so as to find the two ends belonging to a particular one of these wires; there will be a negligible resistance between the "right" ends, and only between the "right" ends. This test is the performed just after the hardware soldering and configuration has been completed. This test aims at finding any electrical open paths in the circuit after the soldering. Many a times, the electrical continuity in the circuit is lost due to improper soldering, wrong and rough handling of the PCB, improper usage of the soldering iron, component failures and presence of bugs in the circuit diagram. We use a multi meter to perform this test. We keep the multi meter in buzzer mode and connect the ground terminal of the multi meter to the ground. We connect both the terminals across the path that needs to be checked. If there is continuation then you will hear the beep sound.
Then we apply this voltage to the power supply circuit. Note that we do this test without microcontroller because if there is any excessive voltage, this may lead to damaging the controller. We check for the input to the voltage regulator i.e., are we getting an input of 12v and an output of 5v. This 5v output is given to the microcontrollers 40th pin. Hence we check for the voltage level at 40th pin. Similarly, we check for the other terminals for the required voltage. In this way we can assure that the voltage at all the terminals is as per the requirement.
83
84
11. RESULTS
85
12 .CONCLUSION
Hence this project has been designed and data from different analog loads has been acquisited and digitally displayed on an LCD. Several loads have been monitored in real time.
Infrastructure processes may be public or private, and include water treatment and distribution, wastewater collection and treatment, oil and gas pipelines, electrical power transmission and distribution, civil defense siren systems, and large communication systems.
86
13. BIBLIOGRAPHY
TEXT BOOKS REFERED:
1. The 8051 Microcontroller and Embedded systems by Muhammad Ali Mazidi and Janice Gillispie Mazidi , Pearson Education. 2. ATMEL 89S52 Data Sheets.
WEBSITES
87