Академический Документы
Профессиональный Документы
Культура Документы
Product Specification
) Preliminary Specification
( ) Final Specification
Title
BUYER MODEL General
*When you obtain standard approval, please use the above model name without suffix SIGNATURE DATE
APPROVED BY /
APPROVED BY
SIGNATURE DATE
REVIEWED BY
PREPARED BY
Please return 1 copy for your confirmation with your signature and comments.
Ver. 1.0
1 / 44
LC470WUD
Product Specification
CONTENTS
Number
COVER CONTENTS RECORD OF REVISIONS 1 2 3 3-1 3-2 3-3 3-4 3-5 3-6 4 5 6 7 7-1 7-2 8 8-1 8-2 9 9-1 9-2 9-3 9-4 9-5 9-6 GENERAL DESCRIPTION ABSOLUTE MAXIMUM RATINGS ELECTRICAL SPECIFICATIONS ELECTRICAL CHARACTERISTICS INTERFACE CONNECTIONS SIGNAL TIMING SPECIFICATIONS SIGNAL TIMING WAVEFORMS COLOR DATA REFERENCE POWER SEQUENCE OPTICAL SPECIFICATIONS MECHANICAL CHARACTERISTICS RELIABILITY INTERNATIONAL STANDARDS SAFETY EMC PACKING Information of LCM Label PACKING FORM PRECAUTIONS MOUNTING PRECAUTIONS OPERATING PRECAUTIONS ELECTROSTATIC DISCHARGE CONTROL PRECAUTIONS FOR STRONG LIGHT EXPOSURE STORAGE HANDLING PRECAUTIONS FOR PROTECTION FILM
ITEM
Page
1 2 3 4 5 6 6 10 12 14 15 16 17 22 24 25 25 25 26 26 26 27 27 27 28 28 28 28
Ver. 1.0
2 / 44
LC470WUD
Product Specification
RECORD OF REVISIONS
Revision No.
0.1 1.0
Revision Date
Oct.09, 2008 Feb.16, 2009
Page
-
Description
Preliminary Specification (First Draft) Final Specification (Update TBD Item)
Ver. 1.0
3 / 44
LC470WUD
Product Specification
1. General Description
LC470WUD is a Color Active Matrix Liquid Crystal Display with an Cold Cathode Fluorescent Lamp(CCFL) backlight system. The matrix employs a-Si Thin Film Transistor as the active element. It is a transmissive type display operating in the normally black mode. It has a 46.96 inch diagonally measured active display area with WUXGA resolution (1080 vertical by 1920 horizontal pixel array) Each pixel is divided into Red, Green and Blue sub-pixels or dots which are arranged in vertical stripes. Gray scale or the luminance of the sub-pixel color is determined with a 10-bit gray scale signal for each dot, thus presenting a palette of more than 1.06Billion(FRC) of colors. It has been designed to apply the 10-bit 4 port LVDS interface. It is intended to support LCD TV, PCTV where high brightness, super wide viewing angle, high color gamut, high color depth and fast moving picture response time are important.
CN2 LVDS
(41pin)
Mini-LVDS(RGB)
2Port
+12.0V
Timing Controller
LVDS
3PinX1CN(High) 3PinX1CN(High)
General Features
Active Screen Size Outline Dimension Pixel Pitch Pixel Format Color Depth Luminance, White Viewing Angle (CR>10) Power Consumption Weight Display Mode Surface Treatment 46.96 inch (1192.87mm) diagonal 1075.6(H) x 620.8 (V) x 33.8 mm (D) (Typ.) 0.5415 mm x 0.5415 mm x RGB 1920 horiz. by 1080 vert. Pixels, RGB stripe arrangement 10Bit(D), 1.06 Billion colors 500 cd/m2 (Center 1 point ,Typ.) Viewing angle free ( R/L 178 (Min.), U/D 178 (Min.)) Total 221W (Typ.) (Logic= 8.06W, Inverter=213W [VBR-A=1.65V] 14.5 Kg (Typ.) Transmissive mode, Normally black Hard coating(3H), Anti-glare treatment of the front polarizer(Haze10%)
4 / 44
Ver. 1.0
LC470WUD
Product Specification
Symbol
VLCD VBL VON/OFF VBR TOP TST HOP HST
Value Min
-0.3 -0.3 -0.3 0 0 -20 10 10
Max
+14.0 +27.0 +5.5 +5.0 +50 +60 90 90
Unit
VDC VDC VDC VDC
Remark
at 25 2 C
ON/OFF Control Voltage Brightness Control Voltage Operating Temperature Storage Temperature Operating Ambient Humidity Storage Humidity
C C
%RH %RH Note 1,2
Note : 1. Temperature and relative humidity range are shown in the figure below. Wet bulb temperature should be Max 39 C and no condensation of water. 2. Gravity mura can be guaranteed below 40C condition.
90% 60 60% Humidity [(%)RH] 50 Wet Bulb Temperature [C] 40 40% 30 20 10 0 10% 10 20 30 40 50 60 70 80 Storage
Operation
-20
Ver. 1.0
5 / 44
LC470WUD
Product Specification
Notes : 1. The specified current and power consumption are under the VLCD=12.0V, 25 2C, fV=120Hz condition whereas mosaic pattern(8 x 6) is displayed and fV is the frame frequency. 2. The current is specified at the maximum current pattern. 3. The duration of rush current is about 2ms and rising time of power input is 0.5ms (min.).
Mosaic Pattern(8 x 6)
Ver. 1.0
6 / 44
LC470WUD
Product Specification
Table 3. ELECTRICAL CHARACTERISTICS (Continue)
Values Parameter Inverter : Power Supply Input Voltage After Aging Power Supply Input Current Before Aging IBL_B Power Supply Input Current (In-Rush) Power Consumption Brightness Adjust On/Off Input Voltage for Control System Signals On Off Irush PBL VBR-A V on V off ExtVBR-B PAL NTSC High Level Low Level 0.0 2.5 -0.3 VBL IBL_A 22.8 24.0 25.2 Vdc A A A A A W Vdc Vdc Vdc % Hz Hz Vdc Vdc On Duty 5 5 HIGH: Lamp on LOW:Lamp off 1 VBR-A = 1.65V 1 VBR-A = 3.3V 1 VBR-A = 1.65V 2 VBR-A = 3.3V 2 VBL = 22.8V Ext VBR-B = 100% VBR-A = 1.65V VBR-A = 1.65V 1 Symbol Min Typ Max Unit Notes
8.9 10 10 11
-
10 11 11 12 15 240
3.3 5.0 0.8 100 102 122 5.0
213
1.65 0.0 100 120 -
Brightness Adjust PWM Frequency for NTSC & PAL Pulse Duty Level(PWM) (Burst mode)
30
98 118 2.5 0.0
0.8
3
Lamp:
Ts
50,000
min Hrs
3 4
Notes : 1. Electrical characteristics are determined after the unit has been ON and stable for approximately 120 minutes at 252C. The specified current and power consumption are under the typical supply Input voltage 24Vand VBR (VBR-A : 1.65V & ExtVBR-B : 100%), it is total power consumption. 2. Electrical characteristics are determined within 30 minutes at 252C. The specified currents are under the typical supply Input voltage 24V. 3. The brightness of the lamp after lighted for 5minutes is defined as 100%. TS is the time required for the brightness of the center of the lamp to be not less than 95% at typical current. The screen of LCD module may be partially dark by the time the brightness of lamp is stable after turn on. 4. Specified Values are for a single lamp which is aligned horizontally. The life time is determined as the time which luminance of the lamp is 50% compared to that of initial value at the typical lamp current (VBR-A : 1.65V & ExtVBR-B :100%), on condition of continuous operating at 25 2C 5. LGD recommend that the PWM freq. is synchronized with One time harmonic of Vsync signal of system. 6. The duration of rush current is about 10ms.
Ver. 1.0
7 / 44
LC470WUD
Product Specification
Notes : 1. All GND(ground) pins should be connected together to the LCD modules metal frame. 2. All VLCD (power input) pins should be connected together. 3. All Input levels of LVDS signals are based on the EIA 644 Standard. (Please see the Appendix X) 4. Specific pins(pin No. #2~#6) are used for internal data process of the LCD module. If not used, these pins are no connection. 5. Specific pins(pin No. #8~#10) are used for OPC function of the LCD module. If not used, these pins are no connection. (Please see the Appendix V for more information.) 6. LVDS pin (pin No. #24,25,40,41) are used for 10Bit(D) of the LCD module. If used for 8Bit(R), these pins are no connection. 7. Specific pin No. #44 is used for No signal detection of system signal interface. It should be GND for NSB(No Signal Black) during the system interface signal is not. If this pin is H, LCD Module displays AGP(Auto Generation Pattern).
Ver. 1.0 8 / 44
LC470WUD
Product Specification
Symbol
NC NC NC NC NC NC NC NC GND R3AN R3AP R3BN R3BP R3CN R3CP GND R3CLKN R3CLKP GND R3DN R3DP
Description
No connection(Reserved) No connection No connection No connection No connection No connection No connection No connection Ground THIRD LVDS Receiver Signal (A-) THIRD LVDS Receiver Signal (A+) THIRD LVDS Receiver Signal (B-) THIRD LVDS Receiver Signal (B+) THIRD LVDS Receiver Signal (C-) THIRD LVDS Receiver Signal (C+) Ground THIRD LVDS Receiver Clock Signal(-) THIRD LVDS Receiver Clock Signal(+) Ground THIRD LVDS Receiver Signal (D-) THIRD LVDS Receiver Signal (D+)
No
22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 -
Symbol
R3EN R3EP GND GND R4AN R4AP R4BN R4BP R4CN R4CP GND R4CLKN R4CLKP GND R4DN R4DP R4EN R4EP GND GND
Description
THIRD LVDS Receiver Signal (E-) THIRD LVDS Receiver Signal (E+) Ground Ground FORTH LVDS Receiver Signal (A-) FORTH LVDS Receiver Signal (A+) FORTH LVDS Receiver Signal (B-) FORTH LVDS Receiver Signal (B+) FORTH LVDS Receiver Signal (C-) FORTH LVDS Receiver Signal (C+) Ground FORTH LVDS Receiver Clock Signal(-) FORTH LVDS Receiver Clock Signal(+) Ground FORTH LVDS Receiver Signal (D-) FORTH LVDS Receiver Signal (D+) FORTH LVDS Receiver Signal (E-) FORTH LVDS Receiver Signal (E+) Ground Ground
Notes : 1. All GND(ground) pins should be connected together to the LCD modules metal frame. 2. LVDS pin (pin No. #22,23,38,39) are used for 10Bit(D) of the LCD module. If used for 8Bit(R), these pins are no connection.
#1
CN1
#51
#1
CN2
#41
#1
#51
#1
#41
[CN1] - Part/No. : FI-RE51S-HF(JAE) - Mating connector : FI-RE51HL (Manufactured by JAE) [CN2] - Part/No. : FI-RE41S-HF(JAE) - Mating connector : FI-RE41HL (Manufactured by JAE)
Ver. 1.0
9 / 44
LC470WUD
Product Specification
3-2-2. Backlight Inverter Master -Inverter Connector : 20022WR-14B1(Yeonho) or Equivalent - Mating Connector : 20022HS-14 or Equivalent Table 5. INVERTER CONNECTOR PIN CONFIGULATION Pin No 1 2 3 4 5 6 7 8 9 10 11 12 13 14 Symbol
VBL VBL VBL VBL VBL GND GND GND GND GND VBR-A VON/OFF EXTVBR-B Status
Description
Power Supply +24.0V Power Supply +24.0V Power Supply +24.0V Power Supply +24.0V Power Supply +24.0V Backlight Ground Backlight Ground Backlight Ground Backlight Ground Backlight Ground Analog Dimming Backlight ON/OFF control External PWM Lamp Status
Master
VBL VBL VBL VBL VBL GND GND GND GND GND VBR-A VON/OFF EXTVBR-B Status
Slave
VBL VBL VBL VBL VBL GND GND GND GND GND Dont care Dont care -
Note
Notes : 1. GND should be connected to the LCD modules metal frame. 2. Minimum Brightness : 0.0V / Maximum Brightness : 3.3V / OPEN : 1.65V 3. Normal : Low (under 0.7V) / Abnormal : High (upper 3.0V) Please see Appendix VI for more information. 4. Each impedance of pin #11, and 13 is 190[K] and 50[K].
PCB 1
12 <Slave>
10 / 44
LC470WUD
Product Specification
Table 6. TIMING TABLE for NTSC/ATSC (DE Only Mode) ITEM Display Period Horizontal Blank Total Display Period Vertical Blank Total Symbol Min 480 40 520 1080 10 1090 Typ 480 70 550 1080 45 1125 Max 480 200 680 1080 86 1166 Unit Note 1920/4 1
Unit
Note
fCLK fH fV
MHz KHz Hz
2 2
Notes : 1. The Input of HSYNC & VSYNC signal does not have an effect on normal operation(DE Only Mode). If you use spread spectrum for EMI, add some additional clock to minimum value for clock margin. 2. The performance of the electro-optical characteristics may be influenced by variance of the vertical refresh rate and the horizontal frequency.
Ver. 1.0
11 / 44
LC470WUD
Product Specification
Table 7 shows the signal timing required at the input of the LVDS transmitter. All of the interface signal timing should be satisfied with the following specification for normal operation.
Table7. TIMING TABLE for DVB/PAL (DE Only Mode) ITEM Display Period Horizontal Blank Total Display Period Vertical Blank Total Symbol Min 480 40 520 1080 228 1308 Typ 480 70 550 1080 270 1350 Max 480 200 680 1080 300 1380 Unit Note 1920/4 1
Unit
Note
fCLK fH fV
MHz KHz Hz
2 2
Notes : 1. The Input of HSYNC & VSYNC signal does not have an effect on normal operation(DE Only Mode). If you use spread spectrum for EMI, add some additional clock to minimum value for clock margin. 2. The performance of the electro-optical characteristics may be influenced by variance of the vertical refresh rate and the horizontal frequency.
Ver. 1.0
12 / 44
LC470WUD
Product Specification
tCLK
0.5 VDD
Invalid data
Pixel 0
Pixel 4
Invalid data
Invalid data
Pixel 1
Pixel 5
Invalid data
Invalid data
Pixel 2
Pixel 6
Invalid data
Invalid data
Pixel 3
Pixel 7
Invalid data
DE(Data Enable)
tHFP
DE(Data Enable)
Ver. 1.0
13 / 44
LC470WUD
Product Specification
R9 R8 R7 R6 R5 R4 R3 R2 R1 R0
G9 G8 G7 G6 G5 G4 G3 G2 G1 G0 0 0 1 0 1 0 1 1 0 0 0 0 1 0 1 0 1 1 0 0 0 0 1 0 1 0 1 1 0 0 0 0 1 0 1 0 1 1 0 0 0 0 1 0 1 0 1 1 0 0 0 0 1 0 1 0 1 1 0 0 0 0 1 0 1 0 1 1 0 0 0 0 1 0 1 0 1 1 0 0 0 0 1 0 1 0 1 1 0 0 0 0 1 0 1 0 1 1 0 0
B9 B8 B7 B6 B5 B4 B3 B2 B1 B0 0 0 0 1 1 1 0 1 0 0 0 0 0 1 1 1 0 1 0 0 0 0 0 1 1 1 0 1 0 0 0 0 0 1 1 1 0 1 0 0 0 0 0 1 1 1 0 1 0 0 0 0 0 1 1 1 0 1 0 0 0 0 0 1 1 1 0 1 0 0 0 0 0 1 1 1 0 1 0 0 0 0 0 1 1 1 0 1 0 0 0 0 0 1 1 1 0 1 0 0
Black Red (1023) Green (1023) Basic Color Blue (1023) Cyan Magenta Yellow White RED (000) RED (001) RED ... RED (1022) RED (1023) GREEN (000) GREEN (001) GREEN ... GREEN (1022) GREEN (1023) BLUE (000) BLUE (001) BLUE ... BLUE (1022) BLUE (1023)
0 1 0 0 0 1 1 1
0 1 0 0 0 1 1 1
0 1 0 0 0 1 1 1
0 1 0 0 0 1 1 1
0 1 0 0 0 1 1 1
0 1 0 0 0 1 1 1
0 1 0 0 0 1 1 1
0 1 0 0 0 1 1 1
0 1 0 0 0 1 1 1
0 1 0 0 0 1 1 1
0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 ... 1 1 1 1 1 1 1 1 1 0 1 1 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
... 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
... 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 ...
... 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
... 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
1 1 1 1 1 1 1 1 1 0 1 1 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 ...
... 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
... 0 0 0 0 0 0 0 0 0 0 0 0
1 1 1 1 1 1 1 1 1 0 1 1 1 1 1 1 1 1 1 1
Ver. 1.0
14 / 44
LC470WUD
Product Specification
0V
10%
T1 T2
T6
Valid Data
T5
Invalid Data Invalid Data
30% 0V
T3
T4 T8
T7
Note :
1. Please avoid floating state of interface signal at invalid period. 2. When the interface signal is invalid, be sure to pull down the power supply VLCD to 0V. 3. The T3/T4 is recommended value, the case when failed to meet a minimum specification, abnormal display would be shown. There is no reliability problem. 4. If the on time of signals(Interface signal and Option signals) precedes the on time of Power(VLCD), it will be happened abnormal display. 5. T6 should be measured after the Module has been fully discharged between power off and on period.
Ver. 1.0
15 / 44
LC470WUD
Product Specification
3-6-2. Sequence for Inverter Power Supply For Inverter
24V (typ.) 90%
VBL
10% 0V 0.7V
T1
T2
1000ms (Min)
T5
T3
T2
1000ms (Min)
VON/OFF
Lamp ON
T4 T4
VBL(Typ.) x 0.8
Notes : 1. T1 describes rising time of 0V to 24V and this parameter does not applied at restarting time. 2. T4(max) is less than T2. 3. In T7 section, EXTVBR-B is recommended 100%.
Ver. 1.0
16 / 44
LC470WUD
Product Specification
4. Optical Specification
Optical characteristics are determined after the unit has been ON and stable in a dark environment at 252C. The values specified are at an approximate distance 50cm from the LCD surface at a viewing angle of and equal to 0 . FIG. 1 shows additional information concerning the measurement equipment and method. Optical Stage(x,y) LCD Module Pritchard 880 or equivalent
50cm FIG. 1 Optical Characteristic Measurement Equipment and Method Table 11. OPTICAL CHARACTERISTICS Parameter
Contrast Ratio Surface Luminance, white Luminance Variation G to G MPRT Uniformity Uniformity RED GREEN Color Coordinates [CIE1931] BLUE WHITE Viewing Angle (CR>10) x axis, right(=0) x axis, left (=180) y axis, up (=90) y axis, down (=270) Gray Scale Ver. 1.0 r l u d 89 89 89 89 2.2 8 17 / 44 degree 7 Ta= 252C, VLCD=12.0V, fV=120Hz, Dclk=74.25MHz VBR_A=1.65V, EXTVBR_B=100%
Symbol
CR LWH WHITE
-
Value Min
1000 400
Typ
1400 500
Max
-
Unit
Note
1
cd/m 1.3 8 12 1 1 ms ms
2 3 4 5 6 6
5P 5 8 0.636 0.334 0.290 Typ -0.03 0.608 0.145 0.064 0.279 0.292
Response Time
MPRT G TO G Rx Ry Gx Gy Bx By Wx Wy
Typ +0.03
LC470WUD
Product Specification
Notes :1. Contrast Ratio(CR) is defined mathematically as : CR(Contrast Ratio) = Maximum CRn (n=1, 2, 3, 4, 5) Surface Luminance at position n with all white pixels CRn = Surface Luminance at position n with all black pixels n = the Position number(1, 2, 3, 4, 5). For more information, see FIG 2. 2. Surface luminance is determined after the unit has been ON and 1Hour after lighting the backlight in a dark environment at 252C. Surface luminance is the luminance value at center 1-point across the LCD surface 50cm from the surface with all pixels displaying white. For more information see the FIG. 2. 3. The variation in surface luminance , WHITE is defined as : WHITE(5P) = Maximum(Lon1,Lon2, Lon3, Lon4, Lon5) / Minimum(Lon1,Lon2, Lon3, Lon4, Lon5) Where Lon1 to Lon5 are the luminance with all pixels displaying white at 5 locations . For more information, see the FIG. 2. 4. Response time is the time required for the display to transit from G(N) to G(M) (Rise Time, TrR) and from G(M) to G(N) (Decay Time, TrD). For additional information see the FIG. 3. (N<M) G to G Spec stands for average value of all measured points. Photo Detector : RD-80S / Field : 2 5. MPRT is defined as the 10% to 90% blur-edge width Bij(pixels) and scroll speed U(pixels/frame)at the moving picture. For more information, see FIG 4 6. Gray to Gray Response time uniformity is Reference data. Please see Appendix XII. 7. Viewing angle is the angle at which the contrast ratio is greater than 10. The angles are determined for the horizontal or x axis and the vertical or y axis with respect to the z axis which is normal to the LCD module surface. For more information, see the FIG. 5. 8. Gray scale specification Gamma Value is approximately 2.2. For more information, see the Table 12. Table 12. GRAY SCALE SPECIFICATION
Gray Level L0 L63 L127 L191 L255 L319 L383 L447 L511 L575 L639 L703 L767 L831 L895 L959 L1023 Ver. 1.0 Luminance [%] (Typ.) 0.07 0.27 1.04 2.49 4.68 7.66 11.5 16.1 21.6 28.1 35.4 43.7 53.0 63.2 74.5 86.7 100 18 / 44
LC470WUD
Product Specification
Measuring point for surface luminance & measuring point for luminance variation.
H A
B V
Response time is defined as the following figure and shall be measured by switching the input signal for Gray(N) and Gray(M).
T rR 100 90
T rD
Optical Response
Ver. 1.0
19 / 44
LC470WUD
Product Specification
MPRT is defined as the 10% to 90% blur-edge with Bij(pixels) and scroll speed U(pixels/frame)at the moving picture.
M=
1 U
Lj
Bij (i=j)
90%
Example) Bij = 12pixels, U = 10pixels / 120Hz M = 12pixels / (10pixels / 120Hz) = 12pixels / {10pixels / (1/120)s} i = 12 / 1,200 s = 10 ms FIG. 4 MPRT
10%
Bij
Normal E Y = 90 , Up
= 180 , Left
= 0 , Right
= 270 , Down
FIG. 5 Viewing angle
Ver. 1.0
20 / 44
LC470WUD
Product Specification
5. Mechanical Characteristics
Table 13 provides general mechanical characteristics. Table 13. MECHANICAL CHARACTERISTICS Item Horizontal Outline Dimension Vertical Depth Horizontal Bezel Area Vertical Horizontal Active Display Area Vertical Weight 584.82 mm 14.5 Kg (Typ.), 15.0 kg (Max.) 592.8 mm 1039.68 mm Value 1075.6 mm 620.8 mm 33.8 mm 1047.6 mm
Note : Please refer to a mechanical drawing in terms of tolerance at the next page.
Ver. 1.0
21 / 44
LC470WUD
Product Specification
<FRONT VIEW>
Ver. 1.0
22 / 44
LC470WUD
Product Specification
<REAR VIEW>
Ver. 1.0
23 / 44
LC470WUD
Product Specification
6. Reliability
Table 14. ENVIRONMENT TEST CONDITION No.
1 2 3 4
Test Item
High temperature storage test Low temperature storage test High temperature operation test Low temperature operation test Ta= 60C 240h Ta= -20C 240h Ta= 50C 50%RH Ta= 0C 240h
Condition
240h
Wave form : random Vibration level : 1.0G RMS Bandwidth : 10-300Hz Duration : X,Y,Z Each direction per 10 min. Shock level :50G(X,Y axis) , 35G(Z axis) Waveform : half sine wave, 11ms Direction : X, Y, Z One time each direction Ta= 40 C, 90%RH 0 - 15,000 feet 0 - 40,000 feet
8 9
Note : Before and after Reliability test, LCM should be operated with normal function
Ver. 1.0
24 / 44
LC470WUD
Product Specification
7-2. EMC
a) ANSI C63.4 Methods of Measurement of Radio-Noise Emissions from Low-Voltage Electrical and Electrical Equipment in the Range of 9kHZ to 40GHz. American National Standards Institute(ANSI), 1992 b) CISPR13 "Limits and Methods of Measurement of Radio interference characteristics of Sound and Television broadcast receivers and associated equipment" CISPR22 "Limits and Methods of Measurement of Radio interference characteristics of Information Technology Equipment" International Special Committee on Radio Interference. c) EN55013 "Limits and Methods of Measurement of Radio interference characteristics of Sound and Television broadcast receivers and associated equipment" EN55022 "Limits and Methods of Measurement of Radio interference characteristics of Information Technology Equipment" European Committee for Electro Technical Standardization.(CENELEC), 1988(Including A1:2000)
Ver. 1.0
25 / 44
LC470WUD
Product Specification
Note 1. YEAR
Year Mark 2001 1 2002 2 2003 3 2004 4 2005 5 2006 6 2007 7 2008 8 2009 9 2010 0
2. MONTH
Month Mark Jan 1 Feb 2 Mar 4 Apr 4 May 5 Jun 6 Jul 7 Aug 8 Sep 9 Oct A Nov B Dec C
b) Location of Lot Mark Serial NO. is printed on the label. The label is attached to the backside of the LCD module. This is subject to change without prior notice.
Ver. 1.0
26 / 44
LC470WUD
Product Specification
9. Precautions
Please pay attention to the followings when you use this TFT LCD module.
LC470WUD
Product Specification
9-5. Storage
When storing modules as spares for a long time, the following precautions are necessary. (1) Store them in a dark place. Do not expose the module to sunlight or fluorescent light. Keep the temperature between 5C and 35C at normal humidity. (2) The polarizer surface should not come in contact with any other object. It is recommended that they be stored in the container in which they were shipped.
Ver. 1.0
28 / 44
LC470WUD
Product Specification
# APPENDIX- I-1 Required signal assignment for Flat Link (Thine : THC63LVD103) Transmitter (Pin7=L or NC)
Host System 30 Bit RED0 RED1 RED2 RED3 RED4 RED5 RED6 RED7 RED8 RED9 GREEN0 GREEN1 GREEN2 GREEN3 GREEN4 GREEN5 GREEN6 GREEN7 GREEN8 GREEN9 BLUE0 BLUE1 BLUE2 BLUE3 BLUE4 BLUE5 BLUE6 BLUE7 BLUE8 BLUE9 Hsync Vsync Data Enable CLOCK 33 34 35 36 37 38 59 61 4 5 40 41 42 44 45 46 62 63 6 8 48 49 50 52 53 54 64 1 9 11 55 57 58 12
Timing Controller
31 30 29 28 25 24 23 22 21 20 19 18
12 13 14 15 16 17 19 20 22 23 24 25 7
100
100
100
RC1P RCLK1N
100
RCLK1P RD1N
100
RD1P RE1N
100
LCM Module
Notes: 1. The LCD module uses a 100 Ohm() resistor between positive and negative lines of each receiver input. 2. Refer to LVDS transmitter data sheet for detail descriptions. (THC63LVD103 or Compatible) 3. 9 means MSB and 0 means LSB at R,G,B pixel data.
Ver. 1.0 29 / 44
GND
LC470WUD
Product Specification
# APPENDIX- 1-2 Required signal assignment for Flat Link (Thine : THC63LVD103) Transmitter (Pin7=H)
Host System 30 Bit RED0 RED1 RED2 RED3 RED4 RED5 RED6 RED7 RED8 RED9 GREEN0 GREEN1 GREEN2 GREEN3 GREEN4 GREEN5 GREEN6 GREEN7 GREEN8 GREEN9 BLUE0 BLUE1 BLUE2 BLUE3 BLUE4 BLUE5 BLUE6 BLUE7 BLUE8 BLUE9 Hsync Vsync Data Enable CLOCK
Timing Controller
31 30 29 28 25 24 23 22 21 20 19 18
12 13 14 15 16 17 19 20 22 23 24 25 7
100
100
100
RC1P RCLK1N
100
RCLK1P RD1N
100
RD1P RE1N
100
LCM Module
Notes: 1. The LCD module uses a 100 Ohm() resistor between positive and negative lines of each receiver input. 2. Refer to LVDS transmitter data sheet for detail descriptions. (THC63LVD103 or Compatible) 3. 9 means MSB and 0 means LSB at R,G,B pixel data.
Ver. 1.0 30 / 44
VCC
LC470WUD
Product Specification
NO. 1 2 3 4 5 6 7 8 9 10 11 12
DESCRIPTION LCD Module BAG TAPE PALLET PACKING,BOTTOM PACKING,TOP ANGLE,POST ANGLE,PACKING ANGLE,COVER BAND,CLIP BAND LABEL 47INCH
MATERIAL
MASKING PAPER 1300X1140X130MM EPS EPS PAPER PAPER PAPER STEEL PP YUPO 80G 100X100
31 / 44
Ver. 1.0
LC470WUD
Product Specification
Model
LC470WUD (SB)(T1)
Serial No. Origin
Ver. 1.0
32 / 44
LC470WUD
Product Specification
LC470WUD SBT1
16 PCS 001/01-01 RoHS Verified MADE IN KOREA
Ver. 1.0
33 / 44
LC470WUD
Product Specification
# APPENDIX- V
T-Con
#8 : VBR-B Input #9 : OPC-OUT
#1
System
LCM Master Inverter
14 VBR-B PWM ( Async. or Sync.) OPC Off OPC On
LCM
12V 3.3V
Slave Inverter
12
PWM Specification ( VDD = 3.3V ) @ OPC 1. PWM High Voltage Range : 2.5V~3.6V 2. PWM Low Voltage Range : 0.0V~0.8V
VDD VDD*0.9
Rising Time Falling Time
VDD*0.1 0
Ver. 1.0
34 / 44
LC470WUD
Product Specification
# APPENDIX- VI
Normal Mode
System Von
Lamp turn on
System Von
Lamp turn on
System
VON/OFF [12pin]
VON
Restart VON
More than 0.1sec
Backlight
Fail
Lamp ON
Inverter
Status [14pin] Inverter pin map
Pin No 11 12 13
Status
1~4sec
Symbol
VBR-A VON/OFF
Description
Analog dimming Control (DC) On/Off Control
14
Status
Ver. 1.0
35 / 44
LC470WUD
Product Specification
# APPENDIX- VII-1
1K
Selector (Pin 7) Selector
50K
ASIC (TCON)
System Side
LCM Side
VCC 1K 1K
Selector (Pin 27)
VCC 25K~75K
Selector
1K
ASIC (TCON)
System Side
LCM Side
Ver. 1.0
36 / 44
LC470WUD
Product Specification
VCC R1 1K
Selector (Pin 10)
R2 1K
R5 25K~75K
Selector
R3 4.7K
R4 OPEN
ASIC (TCON)
System Side
R1 1K
LCM Side
Ver. 1.0
37 / 44
LC470WUD
Product Specification
# APPENDIX- VIII-1
Description LVDS Single end Voltage LVDS Common mode Voltage LVDS Input Voltage Range Change in common mode Voltage
Unit mV V V mV
Notes -
2. AC Specification
LVDS Clock
A
LVDS Data
tSKEW tSKEW
A
Tclk
80%
20% tRF
Tskew_min Tskew_max
Description LVDS Clock to Data Skew Margin LVDS Clock/DATA Rising/Falling time Effective time of LVDS
Min
Max (0.25*Tclk)/7
Unit ps ps ps
Notes 2 -
260 360
Tclk
Notes : 1. All Input levels of LVDS signals are based on the EIA 644 Standard. 2. If tRF isnt enough, teff should be meet the range.
Ver. 1.0 38 / 44
LC470WUD
Product Specification
# APPENDIX- VIII-2
Vcm
VID
Vfsw
Vdata
360ps teff
V+ clk
Vcm
Vclk
Ver. 1.0
39 / 44
LC470WUD
Product Specification
# APPENDIX- IX-1
Ver. 1.0
40 / 44
LC470WUD
Product Specification
# APPENDIX- IX-2
Ver. 1.0
41 / 44
LC470WUD
Product Specification
# APPENDIX- X-1
The deep dimming must be used very carefully due to limitation of lamp characteristics and specification. 1) For stable lamp on, its duty condition should follow below the condition. After Inverter ON signal, T0 duration should be sustained.
Output current
T0 = Min 1 [sec] Min 3[min]
Max duty
2) Low duty(0%~20%) of the inverter output current, B/L may not satisfy some of LCM specification. - Duration : the low duty operation(0 ~ 20%) must be limited within 10 minutes for one time operation. - Ratio : the period of the low duty operation must be less than 1/5 compare to that of the high duty operation(20~100%) in a certain period to prevent unwanted operation. - FOS : partial darkness or darkness of center area during the low duty might be happened due to insufficient lamp current. - Warm up : the low duty must be used 3 min after the lamps ON. In case of low temperature, more warm up time may be needed.
Ver. 1.0
42 / 44
LC470WUD
Product Specification
# APPENDIX- X-2
T0
T1
T2
T3
T2
Value Parameter Min T1 T2 T3 3 T2 x 5 Typ Max 10 min min min Output Current Duty [20%~Max duty] Output Current Duty [0~20%] Output Current Duty [20%~Max duty] Unit Note
3) The output current duty may not be same as input PWM duty due to rise/fall time of output. 4) Following the recommended conditions as aforementioned, there is no difference of lamp lifetime between conventional method and new one.
Ver. 1.0
43 / 44
LC470WUD
Product Specification
# APPENDIX- XII
*Maximum (GtoG) means maximum value of measured time (N, M = 0 (Black) ~ 1023(White), 128 gray step). 0Gray 0Gray 127Gray 255Gray 895Gray 1023Gray
TrD:127G 0G TrD:255G 0G TrD:895G 0G TrD:1023G TrD:255G 127G TrD:895G 127G TrD:895G 255G 255G TrD:1023G 895G
127ray
TrR:0G 127G
255Gray
TrR:0G 255G TrR:127G 255G
895Gray
TrR:0G 895G TrR:127G 895G TrR:255G 895G
1023Gray
TrR:0G 1023G TrR:127G 1023G TrR:255G 1023G TrR:895G 1023G
0G TrD:1023G
127G TrD:1023G
3. Sampling Size : 2 pcs 4. Measurement Method : Follow the same rule as optical characteristics measurement. 5. Current Status Below table is actual data of production on 2009.01.23 ( LGD RV Event Sample)
G to G Response Time [ms] Uniformity Min. #1 #2 3.9 3.8 Max. 6.9 6.7 0.38 0.34
<#1>
Ver. 1.0
<#2>
44 / 44