Вы находитесь на странице: 1из 13

DEPARTMENT OF ELECTRONICS AND COMMUNICATION

ENGINEERING
QUESTION BANK
SUBJECT CODE
: EC1402
SEM / YEAR :
VII/ IV
SUBJECT NAME : OPTICAL COMMUNICATION
UNIT - I
INTRODUCTION TO OPTICAL FIBERS
PART- A ( 2 marks)
1. Among Microwaves and light waves which have high bit rate distance product?Why?
2. Mention the three advantages of optical fiber as waveguide over conventional
metallic waveguide?
3. What is meant by mode and index profile?
4. Mention the advantages of Graded Index fiber.
5. Write the expression for the refractive index in Graded index fiber.
6. Define Numerical Aperture of step index fiber.
7. Give the expression of the effective number of modes that are guided by a curved
multimode fiber of radius ' a'.
8. State Snells Law.
9. Define Critical angle?
10.Define TIR?
11.What is the need of Cladding?
12.Define core index difference.
13.Define refractive index?
14.What are leaky modes in optical fibers?
15.Define External reflection of light rays?


EC1402 OPTICAL COMMUNICATIONS
Kings College Of Engineering - Punalkulam
16.What is meant by modes of waveguide?
17.Define V number?
18.What is relation between V number and power flow in cladding?
19.What is the fundamental parameter of SM fiber?
20.Give the relation between rays and modes?
21.What are the advantages and disadvantages of SM fiber?
22.What are the advantages and disadvantages of MM fiber?
23.Define skew rays and merdional rays?
24.Define cutoff conditions?
25.What is meant by Degenerate modes?
26.What is meant by linearly polarized modes?
27.Define MFD?
28.Define Bi refrigence and beat length?
29.A point source of light is 12cm below the surface of a large body of water (n=1.33).
What is the radius of the largest circle on the water surface through which the lights
can emerge?
30.Consider a parabolic index waveguide with n
1
=1.75,n
2
=1.677 and core radius 52um.
Calculate the numerical aperture at the axis and at a point 20um from the axis.
31.Why do we prefer step index single mode fiber for long distance communication?
32.Why do we use LP
01
mode for long distance communications?
33.What are three operating windows?
34.Alight ray is incident from glass to air. Calculate critical angle?
PART - B
1. What are Fiber modes? Explain mode theory for optical fiber in detail?
(16)
2. Compare SM fiber and Graded index fiber. Explain the requirements for fiber
materials?
(16)
3. Discuss the theory of GI fiber. Derive the expression for the numerical aperture of GI
fiber?
(16)
4. Derive an expression for number of modes propagating in GI fiber from the first
principle .
(16)
5. i) Mention the advantages of optical communication systems?
(8)
ii) Draw the elements of an optical communication systems?
(8)


EC1402 OPTICAL COMMUNICATIONS
Kings College Of Engineering - Punalkulam
6. i) Discuss the propagation modes in SM fiber
(8)
ii)Briefly explain the evolution of fiber optic systems?
(8)
6. i)Compare the configurations of different types of fibers?
(8)
ii) Discuss the modes in Step index fiber?
(8)
7. i)Derive the wave equations for step index fiber and explain?
(8)
ii)Sketch and explain the electric field distributions of low order guided modes in
symmetrical slab waveguide?
(8)
8. A fiber has normalized frequency is 26.6 and wavelength is 1300nm.If the
radius of core is 25um.Compute numerical aperture?
(16)
9. a) A multimode step index fiber with core diameter of 80um and index difference of
1.5% at wavelength of 0.85um.If the refractive is 1.48,find normalized frequency and
no of modes?
(8)
b) Derive the expression for power flow in step index fiber?
(8)
10.a)Explain Linearly polarized modes?
(8)
b)The relative index difference in graded index fiber is 0.7% ,core refractive is
1.45.Find numerical aperture when index profile is triangular.
(8)
11 a).Derive modal equation.
(8)
b) Compare single and multimode fiber.
(8)
UNIT II
SIGNAL DEGRADATION OPTICAL FBERS
PART- A ( 2 marks)
1. An optical signal has lost 55% of its power after traversing 3.5 km of fiber. What is
the loss in dB/km of this fiber?
2. Define mode-field diameter.
3. What are the causes of absorption?
4. Define normalized propagation constant.
5. List the basic attenuation mechanisms in an optical fiber.
6. What is meant be mode coupling ? What causes it ?
7. Mention the two causes of intramodal dispersion.
8. Define fiber loss.


EC1402 OPTICAL COMMUNICATIONS
Kings College Of Engineering - Punalkulam
9. What do you mean be polarization mode dispersion?
10.Commonly available single mode fibers have beat lengths in the range 10cm
<2m. What range of refractive index differences does this correspond to?
11.Find the coupling loss for two fibers having core refractive index profiles
E
=2.0
and
R
=1.5
12.Define Raleigh Scattering loss.
13.Define Mie Scattering loss.
14.When the mean optical power launched into an 8 km length of fiber is 120 uw.
Determine the overall signal attenuation or loss in decibels.
15.How are micro bending losses reduced?
16.Distinguish intrinsic and extrinsic absorption.
17.Distinguish dispersion shifted and dispersion flattened fibers.
PART-B
1. What is meant by waveguide dispersion ? Derive the expression for the same. (16)
2. What is meant be material dispersion ? Derive the expression for the pulse
broadening due to material dispersion.
(16)
3. Discuss the signal distortion in single mode fibers.
(16)
4. Sketch the fundamental mode field in a curved optical wave guide and explain how
bending losses occur.
(16)
5. Explain with suitable diagrams the different mechanisms that contribute to attenuation
in optical fibers.
(16)
6. When the mean optical power launched into an 8km length of fiber is 120 uW, the
mean optical power at the fiber output is 3u W.
Determine
(1) Overall signal attenuation in dB/km and
(8)
(2) The overall signal attenuation for a 10km intervals, each giving an attenuation of
1dB.
(8)
7. Explain in detail mode coupling and design optimization of single mode fibers. (16)
8. Discuss in detail intermodal dispersion of multimode step index fiber with relevant
expression and diagrams.
(16)
9. What is mode coupling ? Discuss pulse broadening in GI fibers.
(16)


EC1402 OPTICAL COMMUNICATIONS
Kings College Of Engineering - Punalkulam
10.Discuss various kinds of losses that an optical signal might suffer while propagating
through fiber. Which is most important one? What is the effect of these losses on
light power and pulse shape?
(16)
11.A 6 km optical link consists of multimode step index with a core refractive index of 1.5
and a relative refractive index difference of 1%. Estimate the delay difference
between the slowest and fastest modes at the fiber output and the rms broadening
due to intermodal dispersion on the link. Also derive the expression involved in it.
(16)
UNIT III
FIBER OPTCAL SOURCES AND COUPLING
PART- A ( 2 marks)
1.
Define radiance.
2.
What is meant by " population inversion"?
3.
what is meant by heterojunction?
4.
What is meant by indirect band gap semiconductor material?
5.
Draw the three key transition processes involved in laser action.
6.
Give examples for direct and indirect semiconductor materials.
7.
Define internal quantum efficiency of an LED.
8.
Name few splicing methods in fiber optics.
9.
Compare LED and LASER.
10.
What so you mean by heterojunction ? Mention its advantages.
a. List the different types of mechanical misalignments that can occur between
two joined fibers.
b. Calculate the ratio of stimulated emission rata to the spontaneous emission
rate for a lamp operating at a temperature of 1000 K. Assume average
operating wavelength is 0.5um.
11.
Define lambertian pattern .
12.
Define FWHM.
13.
Define Modal or speckle noise.


EC1402 OPTICAL COMMUNICATIONS
Kings College Of Engineering - Punalkulam
14.
Define " Kinks".
15.
Define Mode partition noise.
16.
Define Lensing Schemes.
17.
Define Splicing ? What are types of Splicing.?
18.
What are the Characteristics of Light Source .
PART - B
1. Draw the two basic LED configurations and discuss the principle.
(16)
2. Discuss the principle of optical feedback and LASER oscillation.
(16)
3. Derive the threshold condition for LASER oscillation.
(16)
4. Explain various fiber splicing techniques.
(16)
5. Write technical notes on optical fiber connectors.
(16)
6. Discuss the laser diode structures and radiation patterns.(16)
7. Draw the structures of edge - emitting LED and surface emitting LED and
explain the operation.
(16)
8. Discuss the LASER diode principle , modes and threshold conditions.
(16)
9. Explain various types of fiber splicing techniques and fiber connectors.
(16)
10. Derive the threshold condition for LASER
(16)
11. Explain the laser action with neat diagrams.
(16)
12.a) A GaAs laser operating at 850 nm has a 500 um length and a refractive index
n = 3.7. What are the frequency and wavelength spacings?
(6)
b) With neat diagram explain the construction and working of high radiance surface
Emitting LED.
(10)
13. Discuss about modulation of laser diodes. Why thermoelectric coolers are used in
laser diodes.
(16)
14.Discuss in detail fiber splicing and connectors. Explain the operation principles of
WDM.
(16)
15.Draw and explain the LED structures based double hetero structure configuration.(16)
16.Discuss the principles of operation of laser diodes. What are the effects of temperature
on the performance of a laser diode?
(16)
17.Explain in different lensing schemes available to improve the power coupling
efficiency.
(16)


EC1402 OPTICAL COMMUNICATIONS
18.Explain the fiber splicing techniques with necessary diagrams.
(16)
UNIT - IV
FIBER OPTICAL RECEIVERS
PART- A ( 2 marks)
1. Define diffusion length.
2. Define avalanche effect .
3. Define responsivity.
4. Define Quantum efficiency of photo detector.
5. Write the noise sources in the receiver section.
6.Define Quantum limit.
7.What are the desired features of photo detector.
8.A photo diode is constructed of GaAs which has a bandgap energy of 1.43Ev at 300k.
What is meant by long wavelength cutoff?
9.What are the benefits of trans impedance amplifier.
10.Define long wave length cutoff related photo diode.
11.What is meant by bulk dark current?
12.A photo diode has a capacitance of 6pf.Calculate the max load resistance which allows
an 8MHz post defection BW.
13. What is meant by impact ionization. In APD?
14.What is transit time of photo carriers?
15.What is meant by ionization rate?
16. Define avalanche multiplication?
17.Define S/N ratio of an optical receiver?What are the conditions are required
to achieve high S/N?
18.Define BER?
19.Define Extinction ratio?


EC1402 OPTICAL COMMUNICATIONS
Kings College Of Engineering - Punalkulam
20. Define photo current?
21. What is p+ pn+ reach through structure?
22.Define excess noise factor?
23. What is meant by Pre amplifier? What are the advantages of pre amplifier?
24.Whar are the draw backs of high impedance amplifier?
PART - B
1. Describe the working principle of PIN photo detector and explain the characteristics
of pin diode.
(16)
2. Explain with neat diagram, construction and working of APD. Compare photo
detectors.
(16)
3. Discuss the different noise sources and disturbances in the optical pulse detection
mechanism and derive the expression of S/N ratio.
(16)
4. a) Explain the fundamental receiver operation in optical communication.
(6)
b)Derive an expression for the bit error rate of an optical receiver.
(10)
5. Discuss the source of errors in optical receivers
(16)
6. The Quantum efficency of a RAPD is 80% for thr detection of radiation at 0.9um,
when incident optical power is 0.5uw.The output current from the device(after
avalance gain) is 11 uA. Determine avalanche multiplication factor?
(16)
UNIT - V
DIGITAL TRANSMISSION SYSTEM
PART- A ( 2 marks)
1. List out the requirements that are to be considered in analyzing a link
2. Differentiate link power budget and rise time budget.
3. What is SONET? How does it differ from SDH?
4. What are solitons?
5. What is meant by 'modal noise'?


EC1402 OPTICAL COMMUNICATIONS
Kings College Of Engineering - Punalkulam
PART-B
1. Write notes on LINK POWER BUDGET.
(16)
2. Write notes on RISE TIME BUDGET.
(16)
3. Write notes on SONET.
(16)
4. List out the WDM components. Explain them briefly.
(16)
5. Discuss the principles, requirements and applications of WDM.
(16


Part-A


1. A point sorce of ligth is 12 cm below the surface of a large body of water (n =
1.33). What is the radius of the largest circle on the water surface through
whichthe light can emerge?
2. Consider a parabolic index waveguide with n1 =1.75 ,n2 = 1.677 and core
radius
25 micro meter. Calculate the numerical aperture at the axis and at a point 20
micro meter from the axis
3. Define numerical aperture of a step index fiber
4. Define mode-field diameter
5. Commonly available single mode fibers have beat lengths in the range 10 cm <
Lp <2 m . What range of refractive index diffrences does this correspond to? (for
wavelength = 1300 nm)
6. Define mode field diameter
7. What is the fundamental parameter of a single mode fiber?
8. A step index fiber has a normalized frequency V = 26.6 at 1300 nm wavelength.
If the core radius is 25 pm, find the numerical aperture
.
Part-B


9. (i) Diacuss the signal distortion in single mode fibers
(ii) Discuss pulse broadening in graded index fibers with necessary equations
10. (I) Discuss the propagation modes in single -mode fiber
(ii) Discuss the structure of graded index fiber
11. (i) What is meant by 'material dispersion'? Derive its expression
(ii) Discuss the pulse broadening in graded index fiberss
12. (a) What are fiber modes? Explain mode theory for optical fibers in detail.
Or
(b) Compare Single mode fibers and Graded index fibers. Explain the requirements
for fiber materials.










Unit-2


13. Write the expression for the effective number of modes guided by a curved
multimode fiber of radius 'a'
14. Define normalized propagation constant
15. Give expression for the effective number of modes guided by a curved
multimode fiber
16. What are the causes of absorption
17. Find the coupling loss for two fibers having core refractive index profiles alpha
E = 2.0 and alpha R = 1.5 .
18. What causes mode coupling
19. Mention the two causes of intra-modal dispersion.
20. Define fiber loss.
21. (i) Briefly explain the evolution of fiber optic system
(ii) Compare the configuration of different types of fibers .
or
22. (b)(i) Derive modal equation
23. (ii) Discuss the modes in step- index fibers
24. (a) (i) What is meant by material dispersion?
(ii) Derive an expression for material dispersion
(iii) Derive the expression for wave guide dispersion
OR
(b) Discuss the pulse broadening in graded index fibers
25. (i) List the advantages of optical fiber comminication
(ii) Draw the elements of an optical fiber transmission link and explain
26. OR
27. (i) Discuss the mode theory of circular waveguide
28. (a) Discuss various kinds of losses that an optical signal might suffer while
propagating through fiber, Which is most important one? What is the effect of
these losses on light power and pulse shape?


(b) What is mode coupling? Discuss pulse broadening in Gl fibers.


1. Unit-3
29. Draw the three key transistion process involved in laser action
30. Write the concept of indirect bandgap semiconductor materials
31. What is meant by hetero junction?
32. What is meant by indirect band gap semi conductor material?
33. Give example for direct and indirect semiconductor materials
34. Calculate the ratio of stimulated emission rate to the spontaneous emission
rate for a lamp operating at a temperature of 100 K . Assume average operating
wavelength is 0.5 micro meter


35. Compare LED and LASER.
36. What is meant by population inversion
37. (a) Draw the structures of edge-emitting LED and surface emitting LED and
explain the operation
OR
(b) (i)Discuss the LASER diode principle , modes and threshold conditions


38. (a) Draw the structure of edge emitting and surface emitting LEDs and explain
OR
(b) Discuss the laser diode structures and radiation patterns
39. (a)(i) What is meant by heterojunction ? Give example.
(ii) Derive the internal quantum efficiency of an LED
OR
40. (b) (i) Explain optical feedback and laser oscillation.
41. (ii) Derive the threshold condition for lasing
42. (a) With neat diagram explain the construction and working of high radiance
surface emitting LED.
Or
(b) Discuss about modulation of Laser diodes. Why thermoelectric cooler are used
in Laser diodes?
Unit-4
43. Define responsivity of photodiode.
44. Define quantum efficiency of a photodetector
45. Define responsivity
46. A given APD has a quantum efficiency of 65 % at a wavelength of 90 nm . If 0.5
micro watt of optical power produces a multiplied photocurrent of 10 micro
Ampere, find the multiplication


47. Define long wavelength cutoff of a photodiode
48. What is meant by quantum limit?
49. A photodiode is constructed of GaAs, which has band gap energy of 1.43 eV at
300 K. What is meant by long wavelength cutoff?
50. What are the benefits of a trans-impedance amplifier?


51. (a) Draw the schematics of pin photodiode and APD and explain.
OR
(b) Explain the fundamental receiver operation in optical communication


52. (a) An InGaAs pin photodiode has the following parameters at a wavelength of
1300 nm : I D = 4 nA, ? = 0.9, RL = 1000 ohms and the surface leakage current is
negligible. The incident optical power is 300 nw (- 35 dBm), and the receiver
bandwidth is 20 MHz . Find the various noise terms of the receiver
OR
(b) Discuss the performance of digital receiver by defining the probability of
error
53. (a) Discuss the principle of operation of APD wiht neat circuit diagram. Also
discuss the requirements of photo detector.
OR
(b) Discuss the fundamentals of receiver operations with neat block diagram
54. (a) What is known as quantum limit? A digital fiber optic link operating at
850 nm requires a maximum BER of 10*9. Find the minimum incidental optical
power
Po to achieve this BER at a data rate of 10 Mb/s for a simple binary level
signaling scheme. (ry: 1), [1/r : B/2].
Or
(b) Discuss in detail digital receiver performance calculation and sensitivity
calculation in detail.




Unit-5
55. List the sysyem requirements neede in analyzing a point -to- point link
56. Write the concept of solution




57. What is meant by solitron?


58. What is meant by modal noise?


59. Write the basic concept of solition generation


60. Write the concept of link power budget


61. List the key requirements needed in analyzing a link.
62. Define Modal Noise.


63. (a) Explain various types of fiber splicing techniques and fiber connectors
OR
(b) (i) Explain the operational principles of WDM
64. (ii) Explain the rise-time budget.
65. (a) (i) Discuss the operational principles of WDM
66. (ii) Describe the key features of WDM
OR
(b) Explain the rise-time budget of a fiber optic point to point link
67. (a) Draw the point-to -point fiber optic link and discuss the system
considerations
OR
(b) Discuss the principle ,requirement and applications of WDM
68. (a) What are the system consideration in point to point links? Explain in
detail.
Or
(b) Discuss in detail Fiber splicing and connectors. Explain the operation
principles of WDM

Вам также может понравиться