0 оценок0% нашли этот документ полезным (0 голосов)
36 просмотров1 страница
This document provides instructions for setting up and configuring a metal detector. It discusses:
1) Performing a "virtual zero" calibration by shorting the receive coil and adjusting settings to get a baseline reading.
2) Tuning the transmitting and receiving coils to resonance at the same frequency for optimal sensitivity, which involves adjusting coil properties and capacitors.
3) Adjusting the phase relationship between the transmitting and receiving coils to get the proper response to different metal types using trimmer resistors.
4) Configuring the sensitivity using resistors to control coil current and receive channel sensitivity for optimal detection without false positives.
This document provides instructions for setting up and configuring a metal detector. It discusses:
1) Performing a "virtual zero" calibration by shorting the receive coil and adjusting settings to get a baseline reading.
2) Tuning the transmitting and receiving coils to resonance at the same frequency for optimal sensitivity, which involves adjusting coil properties and capacitors.
3) Adjusting the phase relationship between the transmitting and receiving coils to get the proper response to different metal types using trimmer resistors.
4) Configuring the sensitivity using resistors to control coil current and receive channel sensitivity for optimal detection without false positives.
This document provides instructions for setting up and configuring a metal detector. It discusses:
1) Performing a "virtual zero" calibration by shorting the receive coil and adjusting settings to get a baseline reading.
2) Tuning the transmitting and receiving coils to resonance at the same frequency for optimal sensitivity, which involves adjusting coil properties and capacitors.
3) Adjusting the phase relationship between the transmitting and receiving coils to get the proper response to different metal types using trimmer resistors.
4) Configuring the sensitivity using resistors to control coil current and receive channel sensitivity for optimal detection without false positives.
To begin with a look " for a description of the work-menu "
We start by setting up a "virtual zero" receive path. Turning off the coil, put a jumper from ! to the ground and achieve with "tempered" button zero "actually the voltage across the #$ foot controller about %#.& '( readings at the output of the receiving path, this procedure should be followed in setting mode, ")*, +p" "in firmware from version , and above( with the "%" button to remember the value of "!". 'oltage readings should not change -ole than % -./ 0mmediately and can adjust and "correct" reading voltage, like the above "-" button. 1arlier versions setting resistors 2.32# produce and 2432,. Next insist coil for ease of setup rekominduetsya R5 and R17 set the maximum resistance values. Then pick them up already satisfied parameters for sensitivity-staility. 0f you need to configure the sensor resonant receiving 25 "for non-resonant without capacitor !, skip this setting( and a transmitting coil T5 resonance or close to resonance condition. To do this, connect the transmitter coil T5, go to the settings mode "long press the "dir"( sub-mode 5, 6, and the "%" and "-" find the resonant fre7uency overvoltage on coil T5. 8eak voltage should get about .!-$! "depends on the circuit parameters T5(.9s 2emember this fre!uency-". )e:t resound "connected( receiving and transmitting coil "replacing the pre-resistor capacitor . at .!-&! ohms( and the buttons are the same the resonant fre7uency of the receiver circuit at the ma:imum amplitude of the signal at the output ; <#, it may differ from " within % -#!=. farther you get away from the resonance fre7uency of the more stable T5 turn coil. "0t is recommended to configure the receiving 25 by > .!-#!= below. 0e if you T5 -.! k?z tune the 25 4.!- @ k?z.( remind fre7uency " can range from A to .; k?z. 2ecommended fre7uency of ;-.# k?z. Belect the resonant fre7uency can changing the number of turns of the windings or value of the capacitors ! and .. )e:t fit the coil body and reduce the compensating coil 5 "if << is moving coil windings( undervoltage output circuit ; <# "6ou can do a voltmeter "Cole" mode 5, 6-& firmware and above(. Dor normal operation, it should not e:ceed .-/ 0n general, you should aim for the lowest possible value. 1:hibiting our previously scanned fre7uency " or close. Then ad#ust the phase$ When approaching a copper coin 6 and 5 should increase when approaching black metal "iron( 6-5 increases decreases. 0f there is not so with the "!" "discrete steps of A& degrees.( End trimmer 2.; "smooth( phase change while not seeking proper response to metals. 0f this procedure does not work is necessary to choose the capacity !, ., or change the fre7uency of the transmitter. )e:t you need to set the e:act phase for correct measurement of WD0-built resistor 2.;. ? astroit better ferrite phase-5 minus, 6 in place or slightly %. Enother phase can adjust to the "standard" - for e:ample by & kopecks +BB2 value WD0 about &&. WD0 Doil > !-.!, pure copper %4!- %@!, all bits of iron in the red. 0f possible, adjust the trimmer mi:ing coil "s(. %et there is one sutlety& after changing the fre!uency setting ' () *+. find a place ,here the least change -#ump. the value of / and %0 1d#usting the sensitivity$ resistors 2! and 2., are selected coil current T5, The more current the more sensitive as to the objectives and unfortunately and to the ground. 2ecommended current for the resonant system A!-4! ma, no resonance 4!-.!! mE. 2ough estimate of the current in the T5 can be the difference on consumption of the device with and without the coil, then the resonance of #!-A! mE, A!-;! resonance - depends on the F of the circuit. 2esistor 2& is selected channel sensitivity is 25, the smaller the value the higher the sensitivity. 2ecommended resistor values for the resonance system > > .k not resonant #!!th. onfigure the instrument sensitivity is necessary so that at the threshold "sensitivity( of ..# was not false positives "of course in the absence of interference(. Dor high sensitivity in the air do not need to chase, #!-#&, see the ticket/ Bensor diameter > #! sm.<lya sensor diameter #&cm #& $!cm respectively. 2esistor 2.$ adjusted the contrast indicator and its nominal wakes depend on the type of indicator. )oteG In Setup mode, the "+" and "-" to change the frequency in increments TX ~ 10 H! The "0" phase changes "ith a period of #$ %! )ew payment under the chip dip. Dee buildable and proven/ Dor reliable operation, the board is desirable to leave the top layer of foil and connect it to a few "marked in blue( points. <uring installation, see the description of the indicator, power pins happens in different ways/ 2icrochips$ &'()01 can be replaced by )1&&$A, *1#0+,1#0-, ./0$1, .&00-! &icrocontro22er is 3etter to put it ATMEGA8A and consumes 2ess and "or4s 3etter!