Which of the following statements is true concerning a poly-phase synchronous propulsion
motor?
A. The motor is started as an induction motor.
B. Resistance is gradually added to the rotor circuit.
C. The starting current is held below the rated current.
D. The field winding is energized for starting purposes only.
2. When reading electrical motor controller diagrams, it helps to know that ____________.
A. current paths in the control circuit are drawn as heavy lines and in the power circuit as lighter lines
B. current paths in the power circuit are drawn as heavy lines and in control circuit as lighter lines
C. circuits subject to 500 volts or greater are drawn as heavy lines and below 500 volts as lighter lines
D. circuits subject to 500 volts or greater are drawn as light lines and below 500 volts as heavy
3. Alternating current circuits develop resistance, inductance and capacitance. The inductance of a coil is expressed in _____________.
A. ohms B. mhos C. henrys D. farads
4. Large cable sizes are formed as individual conductors that may be comprised of several smaller strands to __________.
A. obtain the flexibility required for easy handling
B. reduce the overall weight of the wire run
C. reduce the number of supports needed for a horizontal overhead run
D. all of the above
5. Which of the following is having Di-Electric Constant 80?
A. Air B. water C. Mica D. Caster oil
6. Where a thermal-acting breaker is required to be used in an area of unusually high, low, or constantly fluctuating temperatures, an ambient compensating element must be used. This element consists of a ______________.
A. cylindrical spring on the contact arm
B. conical spring on the contact arm
C. second bimetal element
D. second electromagnet
7. Which of the following precautions should you take when securing propulsion generators and motors for an extended period of time?
A. Disconnect the brush pigtails from their contacts and circulate air through the units.
B. Disconnect the brush pigtails from their contacts and discharge carbon dioxide into the units to keep them dry.
C. Lift the brushes from commutator collector rings and use the built-in heater to prevent moisture accumulation.
D. Lift the brushes from commutator collector rings and circulate cool dry air through the units.
8. The direction of magnetic flux changes when the direction of current is reversed.
True / False
9. In a Transistor
A. PNP and NPN are two basic types B. Emitter,Collector and Base are the basic Elements. C. Collector separates Base and Emitter D. Emitter separates Base and Collector
9. 9. In a P-Type Semiconductor, the majority current Carriers are ___holes________.
10. In a Control Loop System, having Zero(0) Positive Real Values are called______ PHASE CURRENT ______.
11. If a Motor is not rotating in the E/R, you will carry out the following Checks (multiple choice, 3 Questions of same type but Options were different )
A. Check for the isolation B. Rotate the Coupling with your hand C. Check for the Circuit breaker D. Remove the fuses E Look for the Overload Trip F. Visually Inspect the motor terminals G. Visually Inspect the Starter Terminals H. Carry out Infinite Resistance Test
14. Calculate the Velocity of the conductor (up to 0 decimal places), if terminal voltage is 2.2 V/m and the magnetic field strength is 0.2 T. .
15. Calculate the frequency of the motor ( up to 0 decimal places),, if the speed if 4800 Rpm and number of Poles is 2. N=120f/P => 4800*2/120 =. f = 80
16. If the resistance of any coil is 120 Ohm. Calculate the Resistance (up to 0 decimal places), when its Length is increased by 20% and its Diameter is increased by 50%. R= specific resistance * length / Area Answer 96 R1/R2=L1/L2 * A2/A1 = 120/X= 100/120 * 150/100 =96
17. What is the power in a Resistor in Milli Watts (up to 0 decimal places), having Resistance of 12 Ohm having a Potential Difference of 3 V. P=V^2 / R multiply to get milli watts value
18. Resistance of a wire is increased if the Length is__Increased__ and Area is __decreased___. refer R= specific resistance * length / Area
19. Arrange the following in Increasing Order of their Doping Strength. Answer is-Base, collector, emitter
A. Collector, Emitter, Base B. Base, Emitter, Collector C. Emitter, Base, Collector D. Emitter, Collector, Collector Base, Collector, Base
20. Which of the listed precautions should be taken when cleaning the internals of a motor with compressed air?
A. Open the machine on both ends so as to allow the air and dust to escape.
B. Be certain that the circuit breaker is opened and tagged on the feeder panel.
C. Be certain that the air is clean and as dry as possible.
D. All of the above
Sriram Sridhar 9:38am Nov 4 ONLINE CLASS 4B SEPTEMBER 2012 SUBJECT - M E T guys can u discuss answers for these online elctrical questons which was posted earlier in this group 1) MOTOR RATING GIVEN IN KWHR ,RUN FOR 36 DAYS , FIND POWER CONSUMED IN KWHR ? power=energy/time 2) N = ((120*F) / P) 3) E = B*L*V 4) R = ((RHO * LENGTH)/ CROSS SECTION AREA) area u will take as 3.14/4 * D*D ?????? 5) FIND EFFECTIVE CAPACITANCE IF 4 CAPACITANCE ARE IN SERIES .. n parallel the capacitance is added.. so c=c1+c2+c3+c4 where as in series the reciprocal of capacitance 6) POLYPHASE MOTOR FAILS TO START WHAT TO DO ? 7) MOTOR MAINTENANCE WHAT ALL THINGS TO DO ? 8) SEMICONDUCTOR BORON ADDED WHAT WILL HAPPEN ? by adding boron, it creats a void in lattice,which we call a hole. since the electron is deficient , the hole accepts an electron and maes it positive type of semiconductor. 9) SEMICONDUCTOR CURRENT CARRIERS ? 10) A molded-case breaker provides protection against short circuits by using a/an __________. ____________.ELECTROMAGNET 11) THERMAL CIRCUIT BREAKER ? 12) PN DIODE ADVANTAGE OVER VACUUM DIODE ? (a)LONGER LIFE,b)no warm up time c)less delicate d)all of the above the ans is ALL OF THE ABOVE 13) WHAT IS TRANSDUCER ? .transducer: it is a device, which does not require external electrical power. It is a self generating transducer. For example Solar cell, ... TRANSDUCER CONVERT PRESSURE ENERGY TO ELECTRICAL ENERGY 14) IN SQUIRREL CAGE INDUCTION MOTOR SPEED DEPENDS UPON ? stator poles 14) PROPULSION MOTOR REQUIREMENT ? 15) DATA LOGGER REFRIGERATION ? the name already says it all. With a data logger you can record data over a period of time. It is a small electronic measurement device with either a built-in sensor or external sockets to connect a probe. Data loggers are mostly used because of their ability to measure independently, mostly over a long period of time, therefore unattended measurements are possible with all testo data loggers. data logger is the wired and wireless instrument used in measuremnt of temperature , voltage ,current used in refriegerators, freezers etc. 16) DIELECTRIC CONSTANT OF WATER ? DIELECTRIC CONSTANT OF WATER IS 80 17) FILL IN THE BLANK RELATED TO SEMI CONDUCTOR 18) QUESTION RELATED TO DIODE CURRENT FORWARD BIASED 19) WHAT IS PIV PEAK INVERSE VOLTAGE 20) WIRES WHY MULTIPLE STANDARD flexibility 21) GENERATOR PARALLEL CONDITION ans.voltage, phase and frequency of incoming generator must be same as bus-bar. 22) When reading electrical motor controller diagrams, it helps to know that ____________.(ANS - current paths in the power circuit are drawn as heavy lines and in control circuit as lighter lines ) 23) UNIT OF INDUCTANCE ? Henry 24) TRUE OR FALSE ...RELATING TO PRICIPLE OF ELECTROMAGNETIC INDUCTION ? 25) Tightly knit metal braid wire can be used with a printed circuit board when ___________.DESOLDERING COMPONENTS IN THE CKT
USCG - AROUND 5 QUESTIONS NUMERICALS - 4 QUESTIONS
Calculate the Velocity of the conductor (up to 0 decimal places), if terminal voltage is 2.2 V/m and the magnetic field strength is 0.2 T. 1)2.2/0.2=11m/s
2) If the resistance of any coil is 120 Ohm. Calculate the Resistance (up to 0 decimal places), when its Length is increased by 20% and its Diameter is increased by 50%. R= specific resistance * length / Area Answer 96 R1/R2=L1/L2 * A2/A1 = 120/X= 100/120 * 150/100 =96
3) What is the power in a Resistor in Milli Watts (up to 0 decimal places), having Resistance of 12 Ohm having a Potential Difference of 3 V..... I think 750 mW...... Cause p=v*v/r......that's 0.75 W....
Why resistor of armature winding increases?online qstn armature winding is KEPT AT low resistance because speed regulation of motor is directly porpotional to armature winding is low resistance.to kep regulation of motor low the armature winding has low resistance When the field produced by field winding is changed a back emf produced. This back emf acts as a resistance and limits the current. But during the steady state condition of field the field winding have no back emf. Therefore we need a high resistance in the field winding to limit the current. On the other hand, armature winding produces no back emf at rest. As the speed increases the back emf is also increased. During the running condition the back emf produced by armature winding limits the current. So we don't need a high resistance of the armature winding.
1. Which of the following statements is true concerning a poly-phase synchronous propulsion motor?
A. The motor is started as an induction motor.
B. Resistance is gradually added to the rotor circuit.
C. The starting current is held below the rated current.
D. The field winding is energized for starting purposes only.
2. When reading electrical motor controller diagrams, it helps to know that ____________.
A. current paths in the control circuit are drawn as heavy lines and in the power circuit as lighter lines
B. current paths in the power circuit are drawn as heavy lines and in control circuit as lighter lines
C. circuits subject to 500 volts or greater are drawn as heavy lines and below 500 volts as lighter lines
D. circuits subject to 500 volts or greater are drawn as light lines and below 500 volts as heavy
3. Alternating current circuits develop resistance, inductance and capacitance. The inductance of a coil is expressed in _____________.
A. ohms B. mhos C. henrys D. farads
4. Large cable sizes are formed as individual conductors that may be comprised of several smaller strands to __________.
A. obtain the flexibility required for easy handling
B. reduce the overall weight of the wire run
C. reduce the number of supports needed for a horizontal overhead run
D. all of the above
5. Which of the following is having Di-Electric Constant 80?
A. Air B. water C. Mica D. Caster oil
6. Where a thermal-acting breaker is required to be used in an area of unusually high, low, or constantly fluctuating temperatures, an ambient compensating element must be used. This element consists of a ______________.
A. cylindrical spring on the contact arm
B. conical spring on the contact arm
C. second bimetal element
D. second electromagnet
7. Which of the following precautions should you take when securing propulsion generators and motors for an extended period of time?
A. Disconnect the brush pigtails from their contacts and circulate air through the units.
B. Disconnect the brush pigtails from their contacts and discharge carbon dioxide into the units to keep them dry.
C. Lift the brushes from commutator collector rings and use the built-in heater to prevent moisture accumulation.
D. Lift the brushes from commutator collector rings and circulate cool dry air through the units.
8. The direction of magnetic flux changes when the direction of current is reversed.
True / False
9. In a Transistor
A. PNP and NPN are two basic types B. Emitter,Collector and Base are the basic Elements. C. Collector separates Base and Emitter D. Emitter separates Base and Collector
9. 9. In a P-Type Semiconductor, the majority current Carriers are ______holes_____.
10. In a Control Loop System, having Zero(0) Positive Real Values are called____________. PHASE CURRENT
11. If a Motor is not rotating in the E/R, you will carry out the following Checks (multiple choice, 3 Questions of same type but Options were different )
A. Check for the isolation B. Rotate the Coupling with your hand C. Check for the Circuit breaker D. Remove the fuses E Look for the Overload Trip F. Visually Inspect the motor terminals G. Visually Inspect the Starter Terminals H. Carry out Infinite Resistance Test
14. Calculate the Velocity of the conductor (up to 0 decimal places), if terminal voltage is 2.2 V/m and the magnetic field strength is 0.2 T. 2.2/0.2 = 110M/S
15. Calculate the frequency of the motor ( up to 0 decimal places),, if the speed if 4800 Rpm and number of Poles is 2. .....ans. 80hz formula is N= 120f/p
16. If the resistance of any coil is 120 Ohm. Calculate the Resistance (up to 0 decimal places), when its Length is increased by 20% and its Diameter is increased by 50%. 120 ohm...resistence will remain the same
17. What is the power in a Resistor in Milli Watts (up to 0 decimal places), having Resistance of 12 Ohm having a Potential Difference of 3 V. Ans. 750 mw. Or 75w answer is not sure.. formula is p=VIcos phi
18. Resistance of a wire is increased if the Length is _____increased_____ and Area is ____decreased________.
19. Arrange the following in Increasing Order of their Doping Strength.
A. Collector, Emitter, Base B. Base, Emitter, Collector C. Emitter, Base, Collector D. Emitter, Collector, Collector Base, Collector, Base
20. Which of the listed precautions should be taken when cleaning the internals of a motor with compressed air?
A. Open the machine on both ends so as to allow the air and dust to escape.
B. Be certain that the circuit breaker is opened and tagged on the feeder panel.
C. Be certain that the air is clean and as dry as possible.
D. All of the above
2. What is the maximum allowable primary current of a 2 KVA step-down transformer with a four to one turns ratio if the primary is connected across a 440 volt line? P=vi.- we get I1 , then N1/N2=I2/I1 A 1.1 amps B 4.5 amps C 18.1 amps D 27.7 amps
3. 1. two inductances are in series( 3 hen and 5 hen)..mutual inductance of 2 hen.. total effective inductance??
met:
MARINE ELECTRO TECHNOLOGY
1. Time delayed or delayed action-type fuses are designed to _____________. (A) prevent grounds in branch circuits (B) prevent opens in motor circuits (C) permit momentary overloads without melting (D) guard lighting and electronic circuits Briefly justify your answer
2. Silicon diodes designed for a specific reverse breakdown voltage, become useful as an electronic power supply voltage regulator, called _____________. (A) tunnel diodes (B) hot-carrier diodes (C) compensating diodes (D) Zener diodes Briefly justify your answer
3. Which of the following statements best describes the material known as varnished cambric? (A) Felted asbestos sealed with varnish. (B) Cotton cloth coated with insulating varnish. (C) Rubber insulation coated with a layer of tin. (D) Paper impregnated with mineral oil, specially wrapped with nonmetallic tape, and coated with varnish. Briefly justify your answer
4. A synchronous motor maintains synchronism with the rotating field because _____________. (A) field strength varies directly with rotors lIp (B) DC current applied to the rotor coils causes the rotor magnets to lock in with the rotating flux of the stator (C) the stator poles are dragged around due to the flux created by the excitation current (D) the stator flux rotates in the opposite direction Briefly justify your answer
6. The part of a fuse that melts and opens the circuit is made of _____________. (A) Copper and antimony (B) Steel and Babbitt (C) Aluminum or beryllium alloy (D) Zinc or an alloy of tin and lead Briefly justify your answer
1 the appereant powerin inductive circuit a truepower b lead cinductive d reactive 2 delayed action of fuse is meet ffrequency a lightining b motor c radar d none of above 3 the inductive loop of rotor simple two pole single phase generator rotates 400rps calculate frequency of induceed out put voltage N=120f/P 4 poly phase motor fails what cause for failure what should be check a isolate motor b remove fuse c post cautions signs d ensure starter motor terminals live 5 instrinsic semi conductor is dooped with small amount of boron in the extrinsic semi conductor formed the no of electron hole will precauton to take cleaning the motor with compressed air......... uscg refer 6 when reading electrical motor controller dealing its helps data logger for refregeration systems ... dnt know potions
8 break down diode____zener diode ___ and___avalanche diode____(reverse biasing) 9 basic measuring of inductance a columb b ohm c faraday d henry 10 open loop function system having one zero positiva real valueof __________ phase function 11 semmi conductor failed to over curent reason___low breakdown voltage___ and_________ 12 sum 700w 36dayslike tht question 700xdays 36 x one day 24/ 1000 13 three resistor 40,50,60 connected in series input 30v calculate voltage drop across 60 resistor 14, 15 uscg questions