Академический Документы
Профессиональный Документы
Культура Документы
C US
NSF 61/9
UP CODE
COMPONENT
C US
FM
APPROVED
D1 800-526-3694
TYPE I - STANDARD FIXED & SPARK ARRESTOR
STANDARD WITH SPARK ARRESTOR NOMINAL SIZE ACTUAL DIM.S
WT. PER
FILTER
CASE
MODEL NO. MODEL NO.
H &W
inches & mm
H X W X D
inches
LBS KG QTY
101016 151016 10 x 16 (254mm x 406mm) 9-1/2 x 15-1/2 x 1-3/4 7.4 3.36 6
101020 151020 10 x 20 (254mm x 508mm) 9-1/2 x 19-1/2 x 1-3/4 9.1 4.13 6
101216 151216 12 x 16 (305mm x 406mm) 11-1/2 x 15-1/2 x 1-3/4 8.4 3.81 6
101218 151218 12 x 18 (305mm x 457mm) 11-1/2 x 17-1/2 x 1-3/4 9.3 4.22 6
101220 151220 12 x 20 (305mm x 508mm) 11-1/2 x 19-1/2 x 1-3/4 10.1 4.58 6
101224 151224 12 x 24 (305mm x 610mm) 11-1/2 x 23-1/2 x 1-3/4 12.75 5.78 3
101616 151616 16 x 16 (406mm x 406mm) 15-1/2 x 15-1/2 x 1-3/4 10 4.54 3
101620 151620 16 x 20 (406mm x 508mm) 15-1/2 x 19-1/2 x 1-3/4 12.65 5.74 3
101625 151625 16 x 25 (406mm x 635mm) 15-1/2 x 24-1/2 x 1-3/4 16 7.26 3
102010 152010 20 x 10 (508mm x 254mm) 19-1/2 x 9-1/2 x 1-3/4 9.4 4.26 6
102016 152016 20 x 16 (508mm x 406mm) 19-1/2 x 15-1/2 x 1-3/4 12.65 5.74 3
102020 152020 20 x 20 (508mm x 508mm) 19-1/2 x 19-1/2 x 1-3/4 15 6.8 3
102025 152025 20 x 25 (508mm x 635mm) 19-1/2 x 24-1/2 x 1-3/4 17.9 8.12 3
102516 152516 25 x 16 (635mm x 406mm) 24-1/2 x 15-1/2 x 1-3/4 14.55 6.6 3
102520 152520 25 x 20 (635mm x 508mm) 24-1/2 x 19-1/2 x 1-3/4 18.2 8.26 3
ALL FILTERS ARE AVAILABLE WITH SPECIAL FILTER LOCKING HANDLES.
WHEN ORDERING FILTER LOCKING HANDLES, ADD SUFFIXMH TO MODEL NUMBER.
TYPE 1 WITH SPARK ARRESTOR AVAILABLE.
MEETS CRITERIA SET BY NFPA #96 FOR
COOKING WITH SOLID FUEL
TYPE I - MCDONALDS
NOMINAL SIZE ACTUAL DIM.S
WT. PER
FILTER
CASE
MODEL NO.
H X W
inches & mm
H X W X D
inches
LBS KG QTY
MCD 116 10 x 16 (254mm x 406mm) 9-1/2 x 15-1/2 x 1-3/4 7.4 3.36 6
MCD 116-1.5 10 x 16 (254mm x 406mm) 9-1/2 x 15-1/2 x 1-1/2 7.2 3.27 6
MCD 120 10 x 20 (254mm x 508mm) 9-1/2 x 19-1/2 x 1-3/4 9.1 4.13 6
MCD 120-1.5 10 x 20 (254mm x 508mm) 9-1/2 x 19-1/2 x 1-1/2 8.9 4.04 6
MCD 123 12 x 24 (305mm x 607mm) 11-1/2 x 23-1/2 x 1-3/4 13 5.9 3
MCD 126 12 x 16 (305mm x 406mm) 11-1/2 x 15-1/2 x 1-3/4 8.4 3.81 6
MCD 128 12 x 18 (305mm x 457mm) 11-1/2 x 17-1/2 x 1-3/4 9.3 4.22 6
MCD 133 13-1/2 x 23-13/16 (343mm x 605mm) 13 x 23-1/2 x 1-3/4 13 5.9 3
MCD 136 13-1/2 x 16 (343mm x 406mm) 13 x 15-1/2 x 1-3/4 10 4.54 3
MCD 139 13-1/2 x 19-1/2 (343mm x 495mm) 13 x 19 x 1-3/4 12 5.44 3
TYPE I - Bafe Grease Filters
C US
LISTED
File No. R10173
NFPA #96
C US
LISTED
File No. R10173
NFPA #96
FILTERS AVAILABLE WITH HOOK FOR
USE IN CAPTIvE-AIRE STylE HooDS.
TO ORDERAdd suFFIx (-H)
TO THE MODEL NUMBER.
D2 www.famegardusa.com
TYPE II - HEAVY DUTY STAINLESS STEEL
HEAVY DUTY STAINLESS STEEL NOMINAL SIZE ACTUAL DIM.S
WT. PER
FILTER
CASE
MODEL NO.
H X W
inches & mm
H X W X D
inches
LBS KG QTY
201016 10 x 16 (254mm x 406mm) 9-1/2 x 15-1/2 x 1-7/8 5.5 2.49 6
201020 10 x 20 (254mm x 508mm) 9-1/2 x 19-1/2 x 1-7/8 6 2.72 6
201216 12 x 16 (305mm x 406mm) 11-1/2 x 15-1/2 x 1-7/8 6.5 2.95 6
201220 12 x 20 (305mm x 508mm) 11-1/2 x 19-1/2 x 1-7/8 7 3.18 6
201616 16 x 16 (406mm x 406mm) 15-1/2 x 15-1/2 x 1-7/8 8 3.63 3
201620 16 x 20 (406mm x 508mm) 15-1/2 x 19-1/2 x 1-7/8 8.5 3.86 3
201625 16 x 25 (406mm x 635mm) 15-1/2 x 24-1/2 x 1-7/8 10.5 4.76 3
202016 20 x 16 (508mm x 406mm) 19-1/2 x 15-1/2 x 1-7/8 6.5 2.95 3
202020 20 x 20 (508mm x 508mm) 19-1/2 x 19-1/2 x 1-7/8 10.25 4.65 3
202025 20 x 25 (508mm x 635mm) 19-1/2 x 24-1/2 x 1-7/8 12 5.44 3
202516 25 x 16 (635mm x 406mm) 24-1/2 x 15-1/2 x 1-7/8 11.5 5.22 3
202520 25 x 20 (635mm x 508mm) 24-1/2 x 19-1/2 x 1-7/8 12 5.44 4
TYPE II & TYPE III - Bafe Grease Filters
TYPE III - STAINLESS STEEL
STAINLESS STEEL NOMINAL SIZE ACTUAL DIM.S
WT. PER
FILTER
CASE
MODEL NO.
H X W
inches & mm
H X W X D
inches
LBS KG QTY
301016 10 x 16 (254mm x 406mm) 9-1/2 x 15-1/2 x 1-5/8 4.33 1.96 3
301020 10 x 20 (254mm x 508mm) 9-1/2 x 19-1/2 x 1-5/8 4.06 1.84 16
301216 12 x 16 (305mm x 406mm) 11-1/2 x 15-1/2 x 1-5/8 4 1.81 12
301220 12 x 20 (305mm x 508mm) 11-1/2 x 19-1/2 x 1-5/8 4.92 2.23 12
301616 16 x 16 (406mm x 406mm) 15-1/2 x 15-1/2 x 1-5/8 5.38 2.44 8
301620 16 x 20 (406mm x 508mm) 15-1/2 x 19-1/2 x 1-5/8 6.5 2.95 8
301625 16 x 25 (406mm x 635mm) 15-1/2 x 24-1/2 x 1-5/8 8 3.63 4
301818 18 x 18 (457mm x 457mm) 17-1/2 x 17-1/2 x 1-5/8 6.5 2.95 8
302016 20 x 16 (508mm x 406mm) 19-1/2 x 15-1/2 x 1-5/8 6.5 2.95 8
302020 20 x 20 (508mm x 508mm) 19-1/2 x 19-1/2 x 1-5/8 7.75 3.52 8
302025 20 x 25 (508mm x 635mm) 19-1/2 x 24-1/2 x 1-5/8 9.5 4.31 4
302516 25 x 16 (635mm x 406mm) 24-1/2 x 15-1/2 x 1-5/8 8 3.63 4
302520 25 x 20 (635mm x 508mm) 24-1/2 x 19-1/2 x 1-5/8 9.75 4.42 4
REPLACEMENT BAIL HANDLES: TYPE III - MODEL NO. 300001
ALL FILTERS ARE AVAILABLE WITH SPECIAL FILTER LOCKING HANDLES.
WHEN ORDERING FILTER LOCKING HANDLES, ADD SUFFIXMH TO MODEL NUMBER.
C US
LISTED
File No. R10173
NFPA #96
C US
LISTED
File No. R10173
NFPA #96
NSF
COMPONENT
FILTERS AVAILABLE WITH HOOK FOR
USE IN CAPTIvE-AIRE STylE HooDS.
TO ORDERAdd suFFIx (-H)
TO THE MODEL NUMBER.
D3 800-526-3694
TYPE III - ALUMINUM & GALVANIZED
ALUMINUM
WT. PER
FILTER
GALVANIZED
WT. PER
FILTER
NOMINAL SIZE ACTUAL DIM.S CASE
MODEL NO. LBS KG MODEL NO. LBS KG
H X W
inches & mm
H X W X D
inches
QTY
551016 2 .91 451016 3.36 1.52 10 x 16 (254mm x 406mm) 9-1/2 x 15-1/2 x 1-5/8 8
551020 2.06 .93 451020 4.5 2.04 10 x 20 (254mm x 508mm) 9-1/2 x 19-1/2 x 1-5/8 16
551216 2.35 1.06 451216 4 1.81 12 x 16 (305mm x 406mm) 11-1/2 x 15-1/2 x 1-5/8 6
551220 2.5 1.13 451220 5 2.27 12 x 20 (305mm x 508mm) 11-1/2 x 19-1/2 x 1-5/8 12
551616 2.75 1.25 451616 5.63 2.55 16 x 16 (406mm x 406mm) 15-1/2 x 15-1/2 x 1-5/8 8
551620 3 1.36 451620 6.88 3.12 16 x 20 (406mm x 508mm) 15-1/2 x 19-1/2 x 1-5/8 8
551625 5 2.27 451625 9 4.08 16 x 25 (406mm x 635mm) 15-1/2 x 24-1/2 x 1-5/8 3
552016 3.7 1.68 452016 6.5 2.95 20 x 16 (508mm x 406mm) 19-1/2 x 15-1/2 x 1-5/8 3
552020 3.55 1.61 452020 7.88 3.57 20 x 20 (508mm x 508mm) 19-1/2 x 19-1/2 x 1-5/8 3
552025 5.7 2.59 452025 9.90 4.49 20 x 25 (508mm x 635mm) 19-1/2 x 24-1/2 x 1-5/8 3
552516 4 1.81 452516 8.5 3.86 25 x 16 (635mm x 406mm) 24-1/2 x 15-1/2 x 1-5/8 4
552520 5.7 2.59 452520 9.7 4.40 25 x 20 (635mm x 508mm) 24-1/2 x 19-1/2 x 1-5/8 3
TYPE III & TYPE IV- Aluminum, Galvanized & 20mm Bafe Grease Filters
TYPE IV - 20mm STAINLESS STEEL
STAINLESS STEEL DIMENSIONS THICKNESS
WT.
PER FILTER
CASE
MODEL NO.
WIDTH x HEIGHT
(mm)
(mm)
LBS KG QTY
FG20-500500 500 x 500 20 3.9 1.8 6
FG20-500400 500 x 400 20 4.1 1.9 6
FG20-400400 400 x 400 20 4.9 2.2 6
FG20-400500 400 x 500 20 5.8 2.6 6
FG20-500300 500 x 300 20 4.1 1.9 6
FG20-300500 300 x 500 20 4.8 2.1 6
FG20-495495 495 x 495 20 6.1 2.8 6
REPLACEMENT BAIL HANDLES: TYPE III - MODEL NO. 300001
ALL FILTERS ARE AVAILABLE WITH SPECIAL FILTER LOCKING HANDLES.
WHEN ORDERING FILTER LOCKING HANDLES, ADD SUFFIXMH TO MODEL NUMBER.
C US
LISTED
File No. R10173
NFPA #96
FILTERS AVAILABLE WITH HOOK FOR
USE IN CAPTIvE-AIRE STylE HooDS.
TO ORDERAdd suFFIx (-H)
TO THE MODEL NUMBER.
D4 www.famegardusa.com
TYPE V - s/s, Aluminum & Galvanized Bafe Grease Filters
TYPE V - S/S BRIGHT FINISH
STAINLESS STEEL FINISH NOMINAL SIZE ACTUAL DIM.S
WT. PER
FILTER
CASE
MODEL NO.
H X W
inches & mm
H X W X D
inches
LBS KG QTY
FS50-1016-BA 10 x 16 (254mm x 406mm) 9-1/2 x 15-1/2 x 1-3/4 4.33 1.96 12
FS50-1216-BA 12 x 16 (305mm x 406mm) 11-1/2 x 15-1/2 x 1-3/4 4.06 1.84 12
FS50-1616-BA 16 x 16 (406mm x 406mm) 15-1/2 x 15-1/2 x 1-3/4 4 1.81 6
FS50-2016-BA 20 x 16 (508mm x 406mm) 19-1/2 x 15-1/2 x 1-3/4 4.92 2.23 6
FS50-1020-BA 10 x 20 (254mm x 508mm) 9-1/2 x 19-1/2 x 1-3/4 5.38 2.44 12
FS50-1220-BA 12 x 20 (305mm x 508mm) 11-1/2 x 19-1/2 x 1-3/4 6.5 2.95 12
FS50-1620-BA 16 x 20 (406mm x 508mm) 15-1/2 x 19-1/2 x 1-3/4 8 3.63 6
FS50-2020-BA 20 x 20 (508mm x 508mm) 19-1/2 x 19-1/2 x 1-3/4 6.5 2.95 6
FS50-2520-BA 25 x 20 (635mm x 508mm) 24-1/2 x 19-1/2 x 1-3/4 6.5 2.95 6
FS50-1625-BA 16 x 25 (406mm x 635mm) 15-1/2 x 24-1/2 x 1-3/4 7.75 3.52 6
FS50-2516-BA 25 x 16 (635mm x 406mm) 24-1/2 x 15-1/2 x 1-3/4 9.5 4.31 6
FS50-2025-BA 20 x 25 (508mm x 635mm) 19-1/2 x 24-1/2 x 1-3/4 8 3.63 6
TYPE V - ALUMINUM & GALVANIZED
ALUMINUM
WT. PER
FILTER
GALVANIZED
WT. PER
FILTER
NOMINAL SIZE ACTUAL DIM.S CASE
MODEL NO. LBS KG MODEL NO. LBS KG
H X W
inches & mm
H X W X D
inches
QTY
FA30-1016-HD 1.47 .67 FG35-1016-HD 2.62 1.19 10 x 16 (254mm x 406mm) 9-1/2 x 15-1/2 x 1-3/4 12
FA30-1216-HD 1.68 .76 FG35-1216-HD 2.95 1.34 12 x 16 (305mm x 406mm) 11-1/2 x 15-1/2 x 1-3/4 12
FA30-1616-HD 2.15 .98 FG35-1616-HD 4.35 1.97 16 x 16 (406mm x 406mm) 15-1/2 x 15-1/2 x 1-3/4 6
FA30-2016-HD 2.6 1.18 FG35-2016-HD 4.9 2.22 20 x 16 (508mm x 406mm) 19-1/2 x 15-1/2 x 1-3/4 6
FA30-1020-HD 1.76 .8 FG35-1020-HD 3.39 1.54 10 x 20 (254mm x 508mm) 9-1/2 x 19-1/2 x 1-3/4 12
FA30-1220-HD 2.03 .92 FG35-1220-HD 3.72 1.69 12 x 20 (305mm x 508mm) 11-1/2 x 19-1/2 x 1-3/4 6
FA30-1620-HD 2.6 1.18 FG35-1620-HD 4.9 2.22 16 x 20 (406mm x 508mm) 15-1/2 x 19-1/2 x 1-3/4 6
FA30-2020-HD 3.3 1.5 FG35-2020-HD 5.9 2.68 20 x 20 (508mm x 508mm) 19-1/2 x 19-1/2 x 1-3/4 6
FA30-2520-HD 3.92 1.78 FG35-2520-HD 7.1 3.22 25 x 20 (635mm x 508mm) 24-1/2 x 19-1/2 x 1-3/4 6
FA30-1625-HD 3.37 1.53 FG35-1625-HD 6 2.72 16 x 25 (406mm x 635mm) 15-1/2 x 24-1/2 x 1-3/4 6
FG35-2516-HD 6 2.72 25 x 16 (635mm x 406mm) 24-1/2 x 15-1/2 x 1-3/4 6
FA30-2025-HD 3.92 1.78 FG35-2025-HD 7.1 3.22 20 x 25 (508mm x 635mm) 19-1/2 x 24-1/2 x 1-3/4 6
C US
LISTED
File No. R10173
NFPA #96
C US
LISTED
File No. R10173
NFPA #96
NSF
COMPONENT
NSF
COMPONENT
TYPE V REPLACEMENT LOCKING HANDLES ARE
AVAILABLE IN PAIRS. WHEN ORDERING SPECIFY MOdEL NO. F40-0002
FILTERS AVAILABLE WITH HOOK FOR
USE IN CAPTIvE-AIRE STylE HooDS.
TO ORDERAdd suFFIx (-H)
TO THE MODEL NUMBER.
Alum. & S/S
Only
D5 800-526-3694
94% EFFICIENT AT GREASE EXTRACTION
As tested by Underwriters laboratories of Canada it has been proven that Flame
Gard 1 grease flters have the highest rate of grease extracton of any flter on the
market today while stll maintaining extremely low statc pressures. Quotng U.l.C.
File #CR1157 it was stated that the quantty of grease passing through the flter to
the exhaust duct did not exceed 6% of the amount generated. (Please refer to the
U.l.C. Report contained in the technical secton of our full line catalog.)
SIMPLE BUT EFFECTIVE BAFFLE DESIGN
Flame Gards U shaped bafes were arrived at afer extensive testng. The smooth,
deep bafes cause the grease to drain of the flter quickly, and they resist fame
penetraton without disturbing the movement of air. Flame Gards have more bafes
per inch of flter which is a key factor in our high rate of grease extracton and out
low statc pressure. More bafes mean more grease impingement area and more
paths for the air to fow smoothly and quickly through flter. These combined
features make Flame Gard Is the most energy efcient flters available.
PTFE COATED BAFFLES
Flame Gards high rate of grease extracton is aided by a PTFE coated bafe. In the
same manner that grease rolls of a PTFE coated pan, it rolls down our bafes, out
of the flter and into the hoods remote collecton cup. Because Flame Gards flters
retain only insignifcant amounts of surface grease and do not load, you will have
constancy of air fow throughout your operatng day. In additon, Flame Gards
flters can be easily cleaned in a pot sink or dishwasher with simple detergent and
hot water.
TESTING METHOD
Two sample steel flters were weighed and then mounted side by side in the hood.
The damper was adjusted to provide a stack velocity of approximately 1800 f.p.m.
The distance from the broiler surface to the botom of the unit was approximately
36 in. The grease generator was weighed, partally flled with cooking oil, reweighed
and the weighed recorded.
The grease generatory was placed on the electric broiler and heated untl the
temperature of the cooking oil was 400 F. The sizing of the spray nozzle was such
that grease was discharged at approximately one pound per hour per foot width of
the test hood.
The test contnued for 2 hours...
At the end of the test, the grease laden flters were weighed. The grease collected
from the flter run of was collected and weighed. The grease generator was weighed
again to determine the weight of grease used.
MARYLAND LOCKING HANDLES AVAILABLE
TWO MODELS AVAILABLE....
1. Standard Fixed Bafes
2. Spark Arrestor Screen
SPARK ARRESTOR SCREEN
THE 3/8 X 1/2 (9.5mm x 13mm) SPARK ARRESTOR SCREEN MEETS NFPA 211
REQUIREMENT FOR SOLID FUEL BURNING APPLIANCES
ALL STEEL CONSTRUCTION
ALL SIZES AVAILABLE
NON-LOADING PTFE COATED BAFFLES
LOW STATIC PRESSURE
NATIONAL FIrE PrOTEcTION AssOcIATION NFPA 96,
cHAPTEr 11-5.1 sTATEs
If airborne sparks and embers can be generated by the solid fuel cooking
operaton, spark arrestor devices shall be used prior to the grease removal
device to minimize the entrance of these sparks and embers into the grease
removal device and into the hood and duct system.
NFPA 211 cHAPTEr 1.11.2 (B) sTATEs:
(b) The arrestor screen shall have heat and corrosion resistance equivalent to
19 gauge (0.011 in.) galvanized steel or 24 gauge (0.024 in.) stainless steel.
(c) opening shall not permit the passage of spheres having a diameter larger
than 1/2 in. (12.7mm) nor block the passage of spheres having a diameter of
less than 3/8 in. (9.5mm).
CLASSIFIED BAFFLE GREASE FILTER MEETS NFPA 96
REQUIREMENT FOR COOKING WITH SOLID FUEL
TYPE I
C US
LISTED
File No. R10173
NFPA #96
TYPE I - PTFE-coated Bafe & spark Arrestor
94% EFFICIENT AT GREASE EXTRACTION!
The quantty of grease passing through the flter to the exhaust duct did not
exceed 6% of the amount generated!
RESULTS
THE FOLLOWING DATA WAS RECORDED ON THE UNITS
TESTED. 20 IN. BY 20 IN. STEEL PTFE COATED FILTERS
WEIGHT OF GREASE GENERATED
Before Test
After Test
Cooking Oil Used
95 lb
87.5 lb
7.5 lb
Weight Before
Test
Weight After
Test
Weight of Grease
On Filter
Filter #1 15 lb 6 oz 15 lb 6 oz 0 oz
Filter #2 15 lb 5 oz 15 lb 5 oz 0 oz
Weight of oil collected from the grease flter run off 7 lb 4 oz. Amount of oil
not retained or collected 1 oz. The quantity of grease passing through the
flter to the exhaust duct did not exceed 6 percent of the amount generated.
D6 www.famegardusa.com
TYPE I - PTFE-coated Bafe & spark Arrestor & TYPE II
HOW FLAME GARD WORKS
The afuent from cooking processes contains aerosols of water vapor mixed
with evaporated fat or oil. These are carried from the cooking surface by the
moving air being drawn into the exhaust hood.
Although small, each aerosol is much heavier than the air molecules
surrounding it.
Thus, when the air stream containing these aerosols strikes the Flame Gard
Bafe System, the inertal force of the moisture-grease aerosol is considerably
greater than that of the air molecule. While the air molecule changes
directon easily, the aerosol strikes the bafe with considerable force, causing
it to splater on the surface. Because the surface is coated with a PTFE, the
grease slides down to the trough and then to the collectng container.
Whereas the heaviest aerosols, because of their greater inertal force, impinge
on the surfaces of the bafes facing and perpendicular to the air fow, the
lighter ones remain in the air stream. As the air stream is drawn through the
bafe system, the restrictons in area created by the bafes cause the air to
increase in velocity while changing directon by 180-degrees. Since the inertal
force is a product of the mass and the square of the velocity, this increase in
velocity serves to increase the inertal force of the remaining smaller aerosols,
causing them to impinge on the inner surfaces of the bafes in the same
manner in which the heavier aerosols impinged on the entering surfaces. The
design of the bafe system provides several impingement surfaces and two
rapid 180-degree directon changes.
Because Flame Gard removes grease aerosols from the air stream and drain
them away instead of retaining them. There is no build-up of grease in the
path of the air Flame Gard therefore, insures a constancy of air never before
achievable with mesh-type flters.
SELECTION CHART
ENGINEERING DATA
CFM - STATIC PRESSURE
sTATIc PrEssurE - INcHEs OF H20
cFM PEr FILTEr - (75 AIr)
*Measured 6 (152mm) behind Flame Gard Statc pressure per flter, as
included in this chart, represents the total statc pressure for the system
regardless of the number of flters used in the hood.
c
F
M
P
E
r
F
I
L
T
E
r
-
(
7
5
A
I
r
)
Size 10 x 16 10 x 20 12 x 20 16 x 20 16 x 25 20 x 20 20 x 25
350 .350 .185 .160 .075 .045 .030 .030
400 .495 .240 .205 .095 .055 .055 .040
450 .695 .310 .260 .120 .065 .065 .045
500 .390 .325 .145 .080 .080 .055
550 .485 .395 .175 .100 .100 .065
600 .595 .475 .215 .120 .120 .080
650 .720 .570 .255 .150 .150 .090
700 .670 .300 .180 .180 .105
750 .305 .210 .210 .120
800 .400 .250 .230 .140
850 .460 .290 .290 .165
900 .530 .330 .330 .185
950 .600 .380 .380 .210
1000 .670 .430 .430 .240
1050 .480 .480 .275
1100 .540 .540 .320
1150 .610 .610 .365
TYPE I
A complete list of governmental and industry approvals is available on request.
See Natonal Evaluaton Service report No. NER-255 for allowable values and or
conditons of use concerning material presented in this document. It is subject
to re-examinaton, revisions, and possible cancellaton. NER-255, Conditon of
Use - flters to be used in a kitchen exhaust system that is protected with an
automatc fre suppression system.
UNDERWRITERS lABoRAToRIES, INC., Flame Gard Grease Filters are classifed
by Underwriters laboratories, Inc., as to fammability afer exposure to grease-
laden air only. Guide AKUS, File #R10173 see Underwriters laboratories
Classifed Building Materials Index.
Accepted for use, CITy oF NEW yoRK DEPARTMENT oF BUIlDINGS
NO. MEA481-7.1-SM.
Meets the requirements of NATIoNAl FIRE PRoTECTIoN ASSoCIATIoN,
Standard No. 96.
STAINLESS STEEL GREASE FILTERS
DUAL ACTION
GREASE FILTER FEATURES:
ACTION ONE provides positve fame barrier protecton. Its stainless
steel interlocking bafe walls make it the most efectve fame barrier
of all flters marketed today.
ACTION TWO provides unsurpassed performance in efcient grease
removal. The aerodynamic twin-wall V bafes contnuously separate
grease and air. Stainless steel surfaces assure constant run-of and
allow grease to be safely deposited in collecton troughs.
Safest bafe flter available
Provides positve fame barrier protecton
Heavy Duty solid stainless steel welded constructon
Sturdy drop handles provided
Polished vanes provide self-draining grease run of
Highly efcient in grease removal
Patented vane design prevents grease from dripping-food, utensils and burner
surfaces remain clean
Rugged, welded stainless steel constructon ofers easy cleanability, can
withstand todays harsh cleaning solutons, and fts in standard size dishwasher
Economical...NEVER NEEDS REPLACING
Recommended by leading consultants and designers
Meets requirements of Naton Fire Protecton Associaton Bulletn #96
Tested and classifed by UNDERWRITERS lABoRAToRIES, INC. FIlE #R10173
TYPE II
TABLE 1 HEIGHT OF GREASE FILTERS
Type of cooking Equipment Height Above cooking surface (f.)
Without Exposed Flame 0.5
Exposed Flame 2.0
Charcoal Burning 2.0
D7 800-526-3694
TYPE II
OPERATION
Grease laden air is drawn into the flter by
the exhaust fans. As the air starts through the
aerodynamic v bafe system, it undergoes
a series of compressions, expansions and
pressure changes. The heavy grease is
deposited safely and quickly on the bafes
while the grease-free air passes through the
flter and up the exhaust duct. The bafes smooth surface enables the collected
grease to run of into collecton troughs without dripping on food, utensils or
burner surfaces. The Component Hardware Grease flter method of separatng
grease and air has achieved superior levels for efciency and safety not atained
by compettors flters.
CONSTRUCTION
Component Hardware stainless steel grease flters are constructed of heavy duty
stainless steel, providing the most durable flter available in todays market, and
will provide years of trouble-free operaton. There are no coatngs to wear out
and no involved mechanisms which can jam. All stainless steel grease flters are
guaranteed against defects in workmanship or materials.
MAINTENANCE
The all-stainless steel constructon allows the flter to be soaked, sprayed or placed
in a dishwasher for simplifed cleaning, without concern for rustng or wearing out
of surface coatngs.
TYPE II - Heavy-duty stainless steel Grease Filters
C US
LISTED
File No. R10173
NFPA #96
NSF
COMPONENT
STATIC PRESSURE
CFM
per
Filter
10x20 12x20 16x20
16x25
20x20
25x20
150
175
200
225
250
275
300
325
350
375
400
425
450
475
500
525
550
575
600
625
650
675
700
725
750
775
800
825
850
875
900
925
.12
.18
.25
.31
.38
.46
.55
.63
.72
.84
.95
1.06
1.17
1.32
1.45
1.60
1.75
1.90
02
.06
.11
.16
.21
.26
.31
.37
.43
.50
.56
.62
.70
.77
.85
.92
1.01
1.10
1.18
1.27
1.37
1.47
1.58
1.70
1.81
1.95
03
.07
.11
.15
.18
.23
.27
.32
.37
.42
.47
.52
.57
.62
.66
.75
.81
.87
.93
1.01
1.07
1.14
1.22
1.30
1.37
1.46
1.55
1.65
1.75
1.87
.03
.06
.09
.12
.15
.18
.22
.25
.28
.32
.36
.40
.44
.48
.52
.57
.62
.67
.72
.77
.82
.88
.93
1.00
1.06
1.12
1.17
1.23
.03
.04
.06
.08
.10
.12
.14
.16
.18
.21
.23
.25
.27
.30
.32
.35
.37
.41
.43
.46
.49
.53
.56
.60
.63
.67
.71
EFFECTIVE AREA CHART
NOMINAL (in)
L x W x T
EFFECTIVE AREA
square Feet
10 x 20 x 2
12 x 20 x 2
16 x 20 x 2
16 x 25 x 2
20 x 20 x 2
20 x 25 x 2
1.00
1.25
1.75
2.24
2.25
2.88
ALL COMPONENT HARDWARE
STAINLESS STEEL GREASE FILTERS ARE:
Classifed by Underwriters laboratories Inc.-File #R 10173.
cOMPONENT HArdWArE GrOuP, INc. Grease flter classifcaton by
Underwriters laboratories, Inc., as to fammability only afer exposure to
grease-laden air. See U.l. Classifed Building Material Index. File #R10173
1400
1300
1200
1100
1000
900
800
700
600
500
400
300
200
100
0
C
F
M
P
E
R
F
I
L
T
E
R
.20 .40 .60 .80 1.00 1.20 1.40 1.60 1.80 2.00
STATIC PRESSURE (measured in inches of H
2
0)
AIR FLOW CHARACTERISTICS
2
0
x
2
5
1
6
x
2
5
2
0
x
2
0
1
6
x
2
0
1
2
x
2
0
10 x 20
SELF-BALANCING
With conventonal mesh flters, it is necessary
to pull two to fve tmes as much air through
the center flter to get good smoke and grease
vapor capture on the ends of a hood. This
is a needless waste of costly heated or air
conditoned air.
Component Hardware grease flters are
aerodynamically designed to provide a self-
balancing air fow throughout the entre length
of a hood. Actual feld tests have repeatedly shown a variaton of less than 10
air fow from end to end. This unique design assures good capture through the
entre hood length, with 25 to 50% less volume of exhaust air.
self-Balancing Air Flow
conventonal Mesh Air Flow
D8 www.famegardusa.com
HOW FLAME GARD WORKS
The afuent from cooking processes contains aerosols of water vapor mixed
with evaporated fat or oil. These are carried from the cooking surface by the
moving air being drawn into the exhaust hood. Although small, each aerosol is
much heavier than the air molecules surrounding it. Thus, when the air stream
containing these aerosols strikes the Flame Gard Bafe System, the inertal
force of the moisture-grease aerosol is considerably greater than that of the air
molecule. While the air molecule changes directon easily, the aerosol strikes
the bafe with considerable force, causing it to splater on the surface.
Whereas the heaviest aerosols, because of their greater inertal force, impinge
on the surfaces of the bafes facing and perpendicular to the air fow, the
lighter ones remain in the air stream. As the air stream is drawn through the
bafe system, the restrictons in area created by the bafes cause the air to
increase in velocity while changing directon by 180 degrees. Since the inertal
force is a product of the mass and the square of the velocity, this increase in
velocity serves to increase the inertal force of the remaining smaller aerosols,
causing them to impinge on the inner surfaces of the bafes in the same
manner in which the heavier aerosols impinged on the entering surfaces. The
design of the bafe system provides several impingement surfaces and two
rapid 180-degree directon changes. The grease slides down to the grease
trough and then to the collecton container.
Because Flame Gard removes grease aerosols from the air stream and drain
them away instead of retaining them. There is no build-up of grease in the
path of the air Flame Gard therefore, insures a constancy of air never before
achievable with mesh-type flters.
TYPE III - stainless steel, Galvanized & Aluminum Grease Filters
CFM - Statc Pressure
Statc Pressure - Inches of H20
10 x 16 10 x 2 0 16 x 16 16 x 20 16 x 25 20 x 16 20 x 20 20 x 25 25 x 16 25 x 20
200 .34 .19 .12 .07 .05 .09 .04 .03 .05 .03
300 .84 .48 .33 .19 .12 .23 .11 .07 .13 .07
400 1.46 .83 .57 .33 .21 .41 .19 .13 .23 .13
500 2.27 1.28 .86 .50 .32 .61 .29 .195 .355 .195
600 3.27 1.86 1.27 .73 .46 .90 .42 .28 .52 .29
700 4.45 2.53 1.73 .99 .63 1.23 .57 .38 .70 .39
800 5.73 3.32 2.26 1.30 .82 1.59 .74 .49 .92 .505
900 7.38 4.19 2.87 1.64 1.04 2.04 .94 .64 1.17 .65
1000 9.13 5.15 3.47 2.03 1.28 2.49 1.17 .78 1.425 .79
1100 6.24 4.27 2.44 1.55 3.04 1.40 .95 1.74 .97
1200 7.38 5.08 2.92 1.84 3.59 1.67 1.13 2.07 1.15
1300 8.74 5.98 3.42 2.17 4.26 1.97 1.33 2.44 1.35
1400 6.92 3.95 2.52 4.93 2.28 1.54 2.82 1.56
1500 7.95 4.55 2.89 5.66 2.61 1.77 3.24 1.80
TYPE III
TYPE III sTAINLEss, ALuMINuM ANd GALVANIZEd FILTErs
STATIC PRESSURE SELECTION CHART
A complete list of governmental and industry approvals is available on request.
See Natonal Evaluaton Service report No. NER-255 for allowable values and or
conditons of use concerning material presented in this document. It is subject to
re-examinaton, revisions, and possible cancellaton. NER-255, Conditon of Use
- flters to be used in a kitchen exhaust system that is protected with an automatc
fre suppressions system.
UNDERWRITERS lABoRAToRIES, INC., Flame Gard Grease flters are classifed by
Underwriters laboratories, Inc., as to fammability afer exposure to grease-laden
air only. Guide AKUS, File #R10173, see Underwriters laboratories Classifed
Building Materials Index.
UNDERWRITERS lABoRAToRIES oF CANADA Guide No. 440E13; File No. CR1157.
Accepted for use, CITy oF NEW yoRK DEPARTMENT oF BUIlDINGS
NO. MEA481-7.1-SM.
Meets the requirements of:
NATIONAL FIRE PROTECTION ASSOCIATION, Standard No. 96.
SIZES / INSTALLATION
Flame Gard should always be installed with the bafes in a vertcal positon,
in order to allow the grease partcles to be drawn into the collecton system by
gravity.
Standard sizes are ordered with the vertcal (top to botom) dimension stated frst,
and the horizontal (lef to right) dimension second. For informaton on sizes not
listed, contact the factory, your representatve, or your food-service equipment
dealer.
STAINLESS STEEL
ALUMINUM
GALVANIZED
ALL TESTS CONDUCTED BY CEDRT-AIRE TECHNICAL SERVICES TO AMCA STANDARD 500-89
TABLE 1 HEIGHT OF GREASE FILTERS
Type of cooking Equipment Height Above cooking surface (f.)
Without Exposed Flame 0.5
Exposed Flame 2.0
Charcoal Burning 2.0
C US
LISTED
File No. R10173
NFPA #96
D9 800-526-3694
UNIQUE Roll RoCK CAN SEAM DESIGN MAKES TyPE III THE MoST
DURABLE FILTER ON THE MARKET
WILL NOT FLEX OR TWIST LIKE OTHER FILTERS EVEN AFTER
REPEATED DROPPING
SAFE, DEPENDABLE, POSITIVE FLAME BARRIER PROTECTION
SEAMLESS, SMOOTH SURFACES PERMIT CONSTANT PERMIT GREASE
RUN-oFF INTo HooD CollECTIoN TRoUGHS...EASIly ClEANED By
SOAKING, SPRAYING OR IN CONVENTIONAL DISHWASHERS
ALL STAINLESS STEEL CONSTRUCTION: IS DURABLE AND
CoRRoSIoN-RESISTANT
BRIGHT FINISH: AESTHETICALLY PLEASING, IDEAL FOR
FRoNT-oF-HoUSE INSTAllATIoNS
EFFICIENT: REMOVES A SIGNIFICANT AMOUNT OF GREASE
BEFORE IT CAN ENTER THE VENTILATION SYSTEM, HELPING
TO PROTECT BLOWER EQUIPMENT AND MOTOR
LOW STATIC PRESSURE: INSURES QUIET OPERATION AND
REDUCES OPERATING COSTS
sANITArY: SMooTH, BRIGHT FINISH PRoMoTES GREASE RUN-oFF,
KEEPING FILTERS CLEANER FOR A LONGER PERIOD OF TIME
POsITIVE FIrE-BArrIEr PrOTEcTION: UNIQUE BAFFLE DESIGN
LESSENS THE RISK OF KITCHEN HOOD FIRES SPREADING INTO DUCTWORK
EASY INSTALLATION: TWO HANDLES ON FACE OF FILTER MAKE IT
EASy To INSTAll/REMovE FIlTERS
WASHABLE: FILTERS MAY BE ROUTINELY CLEANED TO ENSURE THEY
OPERATE AT MAXIMUM EFFICIENCY
TYPE IV
TYPE V
20mm TYPE IV BAFFLE GREASE FILTER
COMPONENT HARDWARE GROUP: GREASE FILTER CLASSIFIED BY UNDERWRITERS
LABORATORIES, INC. AS TO FLAMMABILITY AFTER EXPOSURE TO GREASE LADEN AIR
oNly (54-H6). FIlE #R10173 (N) ACCEPTED By THE CITy oF NEW yoRK-DEPARTMENT
OF BUILDINGS-MEA#137-82-E, VOL.2
NoTE: FIRST TWo NUMBERS oF SIZE INDICATE vERTICAl HEIGHT. SECoND TWo NUMBERS REPRESENT HoRIZoNTAl WIDTH, BoTH ARE NoMINAl DIMENSIoNS. ACTUAl SIZE oF FIlTERS ARE
7/16(11mm) lESS THAN NoMINAl. NoMINAl THICKNESS IS 2 (51mm). ACTUAl THICKNESS IS 1-3/4(44mm). STANDARD PACKAGE CoNSISTS oF SIX FIlTERS.
TYPE IV & TYPE V Bafe Grease Filters
GALVANIZED STEEL
FG35 sErIEs
For strong rugged performance, superb
corrosion resistance and absolute low cost
TYPE V BAFFLE TYPE GREASE FILTERS
STANDARD COMMERCIAL SIZES
PATENT 6840975
ALUMINUM
FA30 SERIES
lightweight for ease of handling
NSF
COMPONENT
STAINLESS STEEL & S/S BRIGHT FINISH
Fs50 sErIEs
For tough commercial applicatons and
maximum permanent protecton against
rust and corrosion
NSF
COMPONENT
ALL FILTERS ARE SUPPLIED WITH
STANDARD BAIL HANDLES. FILTERS
WITH LOCKING HANDLES ARE
AVAILABLE TO COMPLY WITH
MARYLAND, VIRGINIA AND
WASHINGTON D.C. SPECIFICATIONS
FOR COMMERCIAL HOODS. TO
ORDER STATE SIZE WITH PREFIX...
FA31...FOR ALUMINUM
FG36...FOR GALVANIZED STEEL
FS51...FOR STAINLESS STEEL
REPLACEMENT LOCKING HANDLES ARE
AVAILABLE IN PAIRS. WHEN ORDERING
SPECIFY MODEL NO. F40-0002.
FG20 sErIEs
C US
LISTED
File No. R10173
NFPA #96
D10 www.famegardusa.com
BAFFLE TYPE GREASE FILTER AIR FLOW CHARACTERISTICS
series FA30, FG35, Fs50
CFM VS STATIC PRESSURE
FLOW RATE
STATIC PRESSURE
FILTEr sIZE: H & W INcHEs (mm)
CFM
(m3/min)
10 x 20
(254 x 508)
12 x 16
(305 x 406)
12 x 20
(305 x 508)
16 x 16
(406 x 406)
16 x 20
(406 x 508)
20 x 20
(508 x 508)
16 x 25
(406 x 635)
20 x 25
(508 x 635)
200 5.6) 0.13 0.15 0.10 0.07 0.04 0.04 0.04 0.03
250 (7.0) 0.27 0.31 0.22 0.16 0.09 0.08 0.09 0.05
300 (8.5) 0.39 0.45 0.31 0.23 0.12 0.13 0.12 0.08
400 (11.3) 0.7 0.8 0.54 0.41 0.23 0.21 0.23 0.15
450 (12.7) 0.89 1.01 0.69 0.51 0.28 0.25 0.28 0.19
500 (14.1) 1.1 1.26 0.85 0.62 0.35 0.32 0.35 0.24
550 (15.6) 1.33 1.52 1.03 0.76 0.43 0.39 0.42 0.28
600 (17.0) 1.58 1.22 0.91 0.51 0.46 0.51 0.34
650 (18.4) 1.44 1.07 0.61 0.52 0.61 0.41
700 (19.8) 1.23 0.7 0.61 0.69 0.47
750 (21.2) 1.42 0.8 .7 .8 0.54
800 (22.6) 0.92 0.8 0.91 0.61
850 (24.0) 1.03 0.89 1.01 0.69
900 (25.5) 1.15 0.99 1.15 0.77
950 (26.9) 1.29 1.11 1.27 0.87
1000 (28.3) 1.42 1.24 1.41 0.96
TYPE V
EFFECTIVE AREA
THE EFFECTIVE AREA FOR NOMINAL SIZE
FILTERS ARE AS LISTED
FILTER SIZE: H & W
INcHEs (mm)
EFFECTIVE AREA
sq. FEET (sq. METErs)
10 x 20
(254 x 508)
1.00 (0.9)
12 x 16
(305 x 406)
0.97 (.09)
12 x 20
(305 x 508)
1.25 (.11)
16 x 16
(406 x 406)
1.36 (.12)
16 x 20
(406 x 508)
1.75 (.16)
20 x 20
(508 x 508)
2.25 (.20)
16 x 25
(406 x 635)
2.24 (.20)
20 x 25
(508 x 635)
2.88 (.26)
MESH TYPE AIR FILTERS
standard commercial sizes Available in...
ALuMINuM FrAMEd MOdELs and
GALVANIZED STEEL FRAMED MODELS
RIGID HEAVY DUTY CONSTRUCTION BEST PRICING
CORROSION RESISTANT ALL STEEL WIRE MESH DESIGN FOR
MAXIMUM CAPTURE OF DUST PARTICLES
ACCEPTED FOR USE BY THE CITY OF NEW YORK
DEPARTMENT OF BUILDING MEA #57-82M
NoTE: STANDARD PACKAGE CoNSISTS oF SIX FIlTERS. NoMINAl THICKNESS IS 2 (51mm)...
actual thickness is 1-3/4(44mm). actual height and width are 7/16(11mm) less than
nominal sizes listed. special size flters and 1(25mm) flters are furnished without handles
lif handles are available on applicaton. all stainless steel (frame and media) models
available on applicaton.
GALVANIZED STEEL FRAMED
F41 SERIES
ALUMINUM FRAMED
F40 SERIES
OPTIONAL SNAP-ON
HANDLES AVAILABLE
(FURNISHED IN PAIRS)
SPECIFY...MODEL NO. F41-0001
AIR DELIVERY DATA CHART
NET FACE
VELOCITY
RESISTANCE IN
INCHES OF W.G.
NOMINAL THICKNESS
CFM
CAPACITY BY SIZE
FPM I INCH 2 INCH 16 x 20 16 x 25 20 x 20 20 x 25
267 .025 .020 467 597 600 768
356 .040 .038 623 796 800 1024
445 067 .060 779 995 1000 1279
533 .100 .090 933 1192 1200 1532
622 .142 .129 1089 1391 1400 1788
711 --- .169 1244 1590 1600 2044
800 --- .218 1400 178 1800 2300
MESH TYPE AIR FILTERS
HEIGHT & WIDTH ALUMINUM FRAMED GALVANIZED STEEL FRAMED
sIZE: INcHEs (mm) MODEL NO.
PACKAGE WGT:
LBs. (kg)
MODEL NO.
PACKAGE WGT:
LBs. (kg)
10 x 20 (254 x 508) F40-1020 11 (5) F41-1020 14 (6)
16 x 20 (406 x 508) F40-1620 18 (8) F41-1620 23 (10)
16 x 25 (406 x 635) F40-1625 22 (10) F41-1625 28(13)
20 x 20 (508 x 508) F40-2020 22 (10) F41-2020 28 (13)
20 x 25 (508 x 635) F40-2025 26 (12) F41-2025 33 (15)
Air Flow characteristcs & Mesh Type Air Filters
D11 800-526-3694
E-Z MOUNT INCANDESCENT
CANOPY LIGHTING FIXTURES FOR COMMERCIAL COOKING HOODS
E-Z MOUNT FEATURE ALLOWS FOR QUICK INSTALLATION GASKETS PERMANENTLY AFFIXED SAVE INSTALLATION TIME
U.L. LISTED AND C.S.A. CERTIFIED FOR USE IN COMMERCIAL COOKING HOODS MEETS ALL REQUIREMENTS FOR NFPA 96 AND N.E.C. 410
DESIGNED FOR CONVENIENT INSTALLATION TO PREWIRED HOODS GREASEPROOF, WATERPROOF AND HEATPROOF CONSTRUCTION
ALUMINUM FIXTURES ARE FURNISHED WITH A BRUSHED FINISH TO MATCH STAINLESS STEEL HOOD INTERIORS
NoTE: **SIlICoNE CoATED GloBES PRovIDED WITH TUFF-SKIN COATING WHICH ELIMINATES
HoT SPoT BRoWNING / DISColoRATIoN oF GloBE...PREvENTS GlASS SHATTER FRoM IMPACT,
DROPPING, UNUSUAL STRESSES AND THERMAL SHOCK. SCRATCH RESISTANT...U.S.D.A. APPROVED...
IMPROVES LIGHT SOURCE BY PROVIDING BETTER DIFFUSION.
UNDERWRITERS LABORATORIES STANDARD #1571 REQUIRES THAT FIXTURES IN COMMERCIAL COOKING
HooDS MUST BE MoUNTED A MINIMUM oF 4 FEET (1219mm) ABovE THE CooKING SURFACE.
B
C
D
A
SPECIFICATIONS
FIXTURE BODY: Die cast aluminum with brushed fnish
SOCKET: Porcelain body with copper shell
WIRE LEADS: 16 AWG, 6 (152mm) long
GROUND LEAD: 6 (152mm) long green colored 18 AWG wire
WATTAGE: Accepts standard 100 wat A19 bulb (not furnished)
VOLTAGE: Rated up to 120 volts
GASKETS: Silicone
GLOBES: Silicone* or clear, thermal and shock resistant
tempered glass
WIRE GUARD: Plated steel
OVERALL SIZE: 5-1/2(140mm) diameter and 8-3/4(222mm) long
with wire guard
JUNCTION BOX: Not furnished. Fixture is designed to accept any
standard 3-1/2(89mm) or 4(102mm) juncton box
E-Z MOUNT CANOPY LIGHTING FIXTURES
REF.
U.L.
MODEL NO.
CSA
MODEL NO.
DESCRIPTION
CASE
QTY
A
L55-1004
*L55-1004-HT
L55-1004-csA
FURNISHED WITH TUFF-SKIN COATED**
THERMAL AND SHOCK RESISTANT
TEMPERED GLASS GLOBE
32
B
L55-1024
*L55-1024-HT
L55-1024-csA
FURNISHED WITH TUFF-SKIN COATED**
THERMAL AND SHOCK RESISTANT
TEMPERED GLASS GLOBE AND WIRE GUARD
32
C
L55-2004
*L55-2004-HT
L55-2004-csA
FURNISHED WITH THERMAL, SHOCK
RESISTANT TEMPERED GLASS GLOBE
32
D
L55-2024
*L55-2024-HT
L55-2024-csA
FURNISHED WITH THERMAL, SHOCK
RESISTANT TEMPERED
GLASS GLOBE AND WIRE GUARD
32
NoTE: MoDElS WITH WIRE GUARD ARE NoT NSF APPRovED
*AvAIlABlE AS HIGH TEMP MoDElS RATED To 392F (200C), 600v, lEADS: 14 AWG, 6 (152mm)
loNG STRIPPED END. INSUlATIoN: SIlICoNE RUBBER WITH TREATED GlASS BEAD SlEEvING
E-Z Mount Incandescent canopy Lightng Fixtures
CERTIFIED
File No. LR63261
C US
LISTED
File No. E80045
NSF
COMPONENT
PATENT PENDING
NEW
E-Z MOUNT FEATURE CUTS
INSTALLATION TIME BY 50%
N
E
W
F
E
A
T
U
R
E
!
D12 www.famegardusa.com
L55 sErIEs LIGHTING FIxTurE rEPLAcEMENT PArTs
REF. MODEL NO. DESCRIPTION CASE QTY
A L55-x022
GLOBE, TEMPERED GLASS
THERMAL AND SHOCK RESISTANT
32
B L50-x011
GLOBE, TEMPERED GLASS SILICONE**
COATED, THERMAL AND SHOCK RESISTANT
32
C L10-x020 WIRE GUARD 32
D
L55-Y001
L55-Y001-csA
*L55-Y001-HT
LAMP HOUSING ASSEMBLY
COMPLETE WITH PORCELAIN SOCKET
AND REQUIRED SILICONE GASKET
32
E L55-x006 SCREW 32
F L50-x009 ADAPTER PLATE 300
G
L55-x003
*L55-x003-HT
PORCELAIN SOCKET 50
H L50-Y001 GASKET SET
*AvAIlABlE AS HIGH TEMP MoDElS RATED To 392F (200C), 600v, lEADS: 14 AWG, 6 (152mm)
loNG STRIPPED END. INSUlATIoN: SIlICoNE RUBBER WITH TREATED GlASS BEAD SlEEvING
NoTE: **SIlICoNE CoATED GloBES PRovIDED WITH TUFF-SKIN COATING WHICH ELIMINATES
HoT SPoT BRoWNING / DISColoRATIoN oF GloBE...PREvENTS GlASS SHATTER FRoM IMPACT,
DROPPING, UNUSUAL STRESSES AND THERMAL SHOCK. SCRATCH RESISTANT...U.S.D.A. APPROVED...
IMPROVES LIGHT SOURCE BY PROVIDING BETTER DIFFUSION.
UNDERWRITERS LABORATORIES STANDARD #1571 REQUIRES THAT FIXTURES IN COMMERCIAL COOKING
HooDS MUST BE MoUNTED A MINIMUM oF 4 FEET (1219mm) ABovE THE CooKING SURFACE.
E-Z Mount Incandescent replacement Parts
G
C
D
A
F
B
E
H
E-Z MOUNT INCANDESCENT
L55 sErIEs LIGHTING FIxTurE rEPLAcEMENT PArTs
CERTIFIED
File No. LR63261
D13 800-526-3694
NSF
COMPONENT
NSF
COMPONENT
recessed Fluorescent canopy Lightng Fixtures
RECESSED FLUORESCENT...LOW PROFILE
NSF LISTED, UL LISTED E250943 FOR USE IN COMMERCIAL COOKING HOODS
MEETS ALL REQUIREMENTS FOR NFPA 96 AND N.E.C. 410
oNly 4-1/2 (114mm) HIGH...FoR lIMITED ovERHEAD ClEARANCE APPlICATIoNS
TEMPERED, PRISMATIC GLASS DIFFUSER WITH ONE PIECE SATIN FINISHED STAINLESS STEEL FACE FRAME TO MATCH HOOD INTERIOR
FLUORESCENT CANOPY HOOD LIGHT FIXTURES
SPECIFICATIONS
BALLAST: Universal 120-277v, 50 or 60 Hz, T8, Ul listed
LAMPS: T8 Fluorescent lamps (not furnished)
BODY: Steel with baked white enamel fnish
MOUNTING: #10-32 x 3/4 (19mm) long threaded studs
REFLECTOR: Baked white enamel fnish... providing a
minimum of 87% difused refecton
DIFFUSER: Crystal 73 tempered prismatc glass with prisms
on inside of fxture, mounted into a stainless
steel face frame with special sealing gasketng.
Secured to fxture body with stainless steel
screws for easy servicing.
RECESSED FLUORESCENT CANOPY HOOD LIGHT FIXTURES
REF
MODEL
NO.
LAMPS
REQD
OVERALL
TRIM SIZE
CUT-OUT
SIZE
HOLES
REQD
DIM.
A L82-1020 (2) F17T8
10-1/4 x 26-1/4
(260mm x 667mm)
8-1/2 x 24-1/2
(216mm x 622mm)
12
6
(152mm)
B L82-1030 (2) F25T8
10-1/4 x 38-1/4
(260mm x 972mm)
8-1/2 x 36-1/2
(216mm x 927mm)
14
7-1/2
(191mm)
C L82-1040 (2) F32T8
10-1/4 x 50-1/4
(260mm x 1276mm)
8-1/2 x 48-1/2
(216mm x 1232mm)
14
10-1/2
(267mm)
9-3/16
(233mm)
1/4(6mm) DIA. HOLES
CUT-OUT
3-1/4
(83mm)
3-1/4
(83mm)
A A A A
MOUNTING CUT-OUT DIAGRAM
2
10-1/4 (260mm)
8
(203mm)
4-1/2
(114 mm)
SECTION
C US
LISTED
File No. E250943
C US
LISTED
File No. E253411
A
B
C
RECESSED INCANDESCENT CANOPY HOOD LIGHT FIXTURE
UL LISTED E253411 AND CERTIFIED FOR CANADA FOR USE IN COMMERCIAL COOKING HOODS
MEETS ALL REQUIREMENTS FOR NFPA 96 AND N.E.C. 410 NSF LISTED TEMPERED, PRISMATIC GLASS DIFFUSER
SATIN FINISHED STAINLESS STEEL FACEPLATE TO MATCH HOOD INTERIORS
SPECIFICATIONS
SOCKET: Side mounted porcelain medium base
WATTAGE: Accepts standard 150 Wat A23 bulb maximum
(not furnished)
VOLTAGE: Rated up to 120 volts
DIFFUSER: Crystal 73 tempered prismatc glass with prisms
on inside of fxture
FACEPLATE: one piece, stainless steel with smooth satn fnish
LOCKUP: (4) captve stainless steel screws
RETAINER: Twin spring and cable for faceplate and frame
REFLECTOR: Die formed aluminum with satn fnish
WIRING: Connectons to socket are made in the interior
removable thermal insulated wiring chamber
BODY: Steel recessed housing with baked white enamel fnish
MOUNTING: (4) #10-24 x 3/4 (19mm) long threaded studs
MOdEL NO. L87-1004
1
3
-
3
/
8
(
3
4
0
m
m
) 6
(
1
5
2
m
m
)
11-3/4
(298mm)
13-3/8
(340mm)
1/4
(6mm)
DIA. HOLES
D14 www.famegardusa.com
quick-Tite
LISTED
3RS9
File No. MH19744
C US
LISTED
3RS9
File No. MH19744
MODEL NO. QuIck-TITE FITTING
WT. PER
FITTING
CASE
QTY
F11-0014 1/4 (6mm) Pipe 2.5 oz (71g) 24
F11-0038 3/8 (10mm) Pipe w/ 1-1/8 (29mm) Hole 3.3 oz (94g) 24
F11-0038A 3/8 (10mm) Pipe w/ 7/8 (22mm) Hole 5.8 oz (164g) 24
F11-0012 1/2 (13mm) Pipe 5.3 oz (150g) 24
F11-0034 3/4 (19mm) Pipe 8.3 oz (235g) 12
F11-0100 1 (25mm) Pipe 13.5 oz (383g) 8
F11-0114 1-1/4 (32mm) Pipe 15.5 oz (439g) 8
F11-0112 1-1/2 (38mm) Pipe 19.0 oz (539g) 8
QUICK-TITE HolE PlUGS ARE DESIGNED To PRovIDE A PoSITIvE SEAl oR PATCH
FOR EXISTING PENETRATIONS THAT ARE NO LONGER REQUIRED
IDEAL TO REPAIR UNWANTED HOLES AS A RESULT OF CHANGES TO A FIRE PROTECTION SYSTEM,
MOVING THE LOCATION OF A FIRE SUPPRESSION NOZZLE, DRILLING A HOLE AT THE WRONG
loCATIoN oR USING A HooD/DUCT WITH PREvIoUSly DRIllED HolES
QUICK-TITE HolE PlUGS ARE EASy To INSTAll AND PRovIDE AN ATTRACTIvE,
FINISHED APPEARANCE TO MATCH FITTINGS
AvAIlABlE FoR FIvE STANDARD HolE SIZES - 3/4, 7/8, 1-1/8, 1-3/8, AND 1-5/8
MODEL NO. HOLE SIZE
WT. PER
HOLE PLUG
CASE
QTY
F12-0034 3/4 (19mm) to 7/8 (22mm) 3.2 oz (91g) 24
F12-0078 7/8 (22mm) to 1 (25mm) 4.8 oz (136g) 24
F12-0118 1-1/8 (29mm) to 1-5/16 (33mm) 7.2 oz (204g) 12
F12-0138 1-3/8 (35mm) to 1-9/16 (40mm) 12.8 oz (363g) 12
F12-0158 1-5/8 (41mm) to 1-7/8 (48mm) 21.6 oz (612g) 6
QUICK-TITE
FITTINGS
QUICK-TITE
HOLE PLUGS
MODEL NO. CORNER PULLEY WT. PER PULLEY CASE QTY
F11-0012A 7/8-18 x 1/2 NPT 5.1 oz (145g) 24
F11-0012B 15/16-20 x 1/2 NPT 4.9 oz (139g) 24
D15 800-526-3694
PLUG BODY
(Replaces adapter body
when ordering Hole Plug)
ADAPTER BODY
GASKET
METAL WALL
NUT
LOCK
WASHER
ADAPTER
BODY
GASKET
HOOD
or
DUCT
LOCK
WASHER
NUT
A
B
D
C
MODEL NO. SIZE OF PIPE
A = CUT OUT
HOLE SIZE
B C D
F11-0014 1/4 (6mm) 3/4 (19mm) to 7/8 (22mm) 0.88 1.13 hex 0.25
F11-0038 3/8 (10mm) 1-1/8 (29mm) to 1-5/16 (33mm) 1.00 1.50 hex 0.31
F11-0038A 3/8 (10mm) 7/8 (22mm) to 1 (25mm) 1.00 1.50 hex 0.31
F11-0012 1/2 (13mm) 1-1/8 (29mm) to 1-5/16 (33mm) 1.14 1.50 hex 0.31
F11-0034 3/4 (19mm) 1-3/8 (35mm) to 1-9/16 (40mm) 1.25 1.88 hex 0.31
F11-0100 1 (25mm) 1-5/8 (41mm) to 1-7/8 (48mm) 1.50 2.25 hex 0.38
F11-0114 1-1/4 (32mm) 2 (51mm) to 2-1/4 (57mm) 1.50 2.50 hex 0.38
F11-0112 1-1/2 (38mm) 2-1/4 (57mm) to 2-1/2 (64mm) 1.50 2.75 hex 0.38
QUICK-TITE
ASSEMBLY BREAKDOWN
HOLE PLUG DIMENSIONAL DRAWING
REPAIR KIT INCLUDES
1 TUBE - SIl300 HIGH TEMPERATURE SIlICoNE ADHESIvE,
10.3 oZ (305ml) CARTRIDGE WITH REMovABlE TIP
1 Roll - HIGH TEMPERATURE SIlICA CloTH GASKET,
.090 (2.3mm) THICK X 1.5 (38mm) WIDTH X 50 (15m) lENGTH
GASKET REPAIR KIT
SIL300 SILICONE FIRESTOP SEALANT IS:
C
L
A
SSIF
IE
D
C US
3L73
FILL, VOID OR CAVITY MATERIAL CLASSIFIED BY UNDERWRITERS LABORATORIES INC.
FOR USE IN THROUGH-PENETRATION FIRESTOP SYSTEMS.
SEE UL FIRE RESISTANCE DIRECTORY UNDERWRITERS LABORATORIES
ACCESS PANEL
KIT INClUDES ENoUGH MATERIAl To REPAIR 7-16 ACCESS DooRS, DEPENDING oN DooR SIZES
quick-Tite
A
B
Optional 4(102 mm) studs
for zero clearance duct
wrap-order with Suffx (-4)
D19 800-526-3694
FLAT ACCESS DOORS
MODEL NO. PANEL OUTSIDE DIMENSION
PANEL
HEIGHT
STUD
HEIGHT
HOLE SIZE
Inches (mm)
MTG
STUDS
A B C D E F
750710 7 (178mm) 10 (254mm) FLAT 1 (25mm) 5.5 (140mm) 8.5 (216mm) 6
750715 7 (178mm) 15 (381mm) FLAT 1 (25mm) 5.5 (140mm) 13.5 (343mm) 6
750723 7 (178mm) 23 (584mm) FLAT 1 (25mm) 5.5 (140mm) 21.5 (546mm) 10
750606 8 (203mm) 8 (203mm) FLAT 1 (25mm) 6 (152mm) 6 (152mm) 4
750707 10 (254mm) 10 (254mm) .5 (13mm) 1 (25mm) 7 (178mm) 7 (178mm) 4
750712 10 (254mm) 15 (381mm) .5 (13mm) 1 (25mm) 7 (178mm) 12 (305mm) 6
750720 10 (254mm) 23 (584mm) .5 (13mm) 1 (25mm) 7 (178mm) 20 (508mm) 10
751212 15 (381mm) 15 (381mm) .5 (13mm) 1 (25mm) 12 (305mm) 12 (305mm) 8
751220 15 (381mm) 23 (584mm) .5 (13mm) 1 (25mm) 12 (305mm) 20 (508mm) 14
751620 19 (483mm) 23 (584mm) .5 (13mm) 1 (25mm) 16 (406mm) 20 (508mm) 16
752020 23 (584mm) 23 (584mm) .5 (13mm) 1 (25mm) 20 (508mm) 20 (508mm) 16
EASY TO CLEAN AND EASY TO INSTALL
GASKET RATED To 2300F (1260C) FOR FIRE TIGHT SEAL GASKET IS HIGH-TEMP BoNDED To FRoNT PANEl
AVAILABLE WITH EXTENDED STUDS TO ACCOMMODATE FIRE WRAP FOR FLAT DUCT APPLICATIONS
HEAvy-DUTy 16 GAUGE STEEl CoNSTRUCTIoN STAINLESS STEEL MODEL AVAILABLE NO MINIMUM ORDER REQUIREMENTS
PoSITIvE BolT PATTERN ENSURES FIRE-SAFE CloSURE BACK FRAME REINFoRCES DUCT CUT-oUT
STANDARD AND CUSTOM SIZES AVAILABLE
UL FIRE RATED FLAT ACCESS DOORS
E
F
C
A
B
B
A
D
Door
Gasket
NOTE: Gasket is
High Temp bond-
ed to front panel
Optional 4(102 mm) studs
for zero clearance duct
wrap-order with Suffx (-4)
E-Clip holds back frame
to duct for each stud
E-Clip
Wing Nuts
**Access Panels over
7 x 7 (178mm x 178mm)
have a 1/2 13mm) turndown
to add rigidity to the panel.
Smaller sizes do not have
a turndown.
Back
Frame
Flat Access doors uL Fire rated
HOOD AND DUCT
ACCESSORY
65X3
File No. MH16475
NFPA #96
D20
Component Hardware Group, Inc.
1890 Swarthmore Avenue, PO Box 2020, Lakewood, NJ 08701 Tel. 800-526-3694 732-363-4700 Fax 732-364-8110
www.flamegardusa.com
COMPONENT
CONFORMS TO NFPA REQUIREMENTS
6-3/4
(171mm)
2-1/2
(64mm)
4
(102mm)
4
(102mm)
KEYHOLE MOUNT CUP
MOdEL NO. F15-2500-c
Size: 4 x 6-3/4 x 2-1/2 DEEP
(102mm x 171mm x 64mm)
REF. B REF. C
REF. A
A
B C
10 MOUNTING
ANGLE
4
(102mm)
6-5/8
(168mm)
D23 800-526-3694
10.3 oz (305ml)
NSF LISTED FDA APPROVED
AVAILABLE IN CLEAR, BRIGHT ALUMINUM, WHITE,
BlACK AND RED (HI-TEMP)
FITS ALL STANDARD CAULKING GUNS
U.L. RECOGNIZED
MEETS FDA EXTRACTION REQUIREMENT
NO. 21 CFR177.2600
FURNISHED WITH REMOVABLE TIP
MODEL NO. COLOR MAX. SERVICE CASE QTY
M90-1010 CLEAR 392F (200C) 10
M90-1012 ALUMINUM 392F (200C) 10
M90-1014 WHITE 392F (200C) 10
M90-1016 BLACK 392F (200C) 10
M90-1018 HI TEMP RED 500F (260C) 10
MASTER CASE QTy: 50
AlSo AvAIlABlE IN 3 oz (85g) TUBES
CLEAR: M90-0310 ALUMINUM: M90-0312 WHITE: M90-0314
PACKAGED 20 PER PACK
5 GAlloN (19 liter): MOdEL NO. M90-5012
SILICONE SEALANT
INSULATION HANGERS
PROVIDED WITH PEEL AND PLACE ADHESIVE BACKING
ANNEALED COPPER COATED STEEL NAIL
ELIMINATES USING CAPACITOR DISCHARGE NAILS
SUPPLIED WITH GALVANIZED STEEL RETAINING PLATE
Insulaton Hangers are made of 2 x 2 (51mm x 51mm)
Galvanized Plates with a 1/32(.794mm) white urethane foam
backing which has been coated with a high performance,
acrylic based adhesive protected by a release coated liner.
NoTE: oTHER lENGTHS AvAIlABlE UPoN REQUEST
MODEL NO. HANGER LENGTH CASE QTY
q86-1000 1 (25mm) 1000
q86-1250 1-1/4 (32mm) 1000
q86-1500 1-1/2 (38mm) 1000
q86-1625 1-5/8 (41mm) 1000
q86-2000 2 (51mm) 1000
MODEL NO. PIN SIZE CASE QTY
q86-0010 12 GA. x 1(25mm) 1000
q86-0015 12 GA. x 1-1/2(38mm) 1000
q86-0020 12 GA. x 2(51mm) 1000
RETAINING PLATE
q86-0001 1 x 1-1/4 (32mm) 1000
INSULATION WELD PINS
ANNEALED COPPER COATED STEEL NAIL CD TYPE
GALVANIZED STEEL RETAINING PLATE AVAILABLE
FOIL AND DUCT TAPE
IDEAL FOR SEALING SEAMS AND JOINTS ON HVAC DUCTS
REF. MODEL NO. TYPE SIZE CASE QTY
A q84-3200 HEAVY DUTY DUCT TAPE
2 x 60 yDS
(51mm x 55m)
24
B q84-4250
HI-STRENGTH
ALUMINUM FOIL TAPE
2-1/2 x 50 yDS
(64mm x 46m)
16
A.
B.
File No. E224060
NSF
COMPONENT
sealant, caulking Gun, Tape, Insulaton Hangers & Weld Pins
3oz Tube
CAULKING GUN
For Use With
10.3 oz (305ml) Cartridge
MODEL NO. Q99-1000
D24 www.famegardusa.com
MODEL NO. DESCRIPTION NET CONTENT
BOX/CASE
QTY
q85-2004 (shown) Pump Spray 4 f. oz. (118ml) Each
q85-200424 Pump Spray 4 f. oz. (118ml) 24/Box
q85-2016 (shown) Pump Spray 16 f. oz. (474ml) Each
q85-201606 Pump Spray 16 f. oz. (474ml) 6/Box
q85-201612 Pump Spray 16 f. oz. (474ml) 12/Case
MODEL NO. DESCRIPTION NET CONTENT BOX QTY
q85-2128 (shown) Refll 1 gal. (3.8ml) Each
q85-212804 Refll 1 gal. (3.8ml) 4/Box
Brite Gard
CLEANS, SHINES & PROTECTS
DOES NOT LEAVE OILY RESIDUE
ENvIRoNMENTAlly FRIENDly USES MANUAl
PUMP SPRAYER, NOT AEROSOLS
VIRTUALLY ELIMINATES FINGERPRINTS & SMUDGES
SPECIFICALLY FORMULATED FOR USE ON
INDooR/oUTDooR STAINlESS STEEl APPlIANCES
SAFE USES FooD GRADE INGREDIENTS
MODEL NO.
Q85-2128
Biodegradable
100% Recyclable
MODEL NO.
Q85-2016
MODEL NO.
Q85-2004
Brite Gard
cleaning Products
HEAVY-WEIGHT quArTErFOLd
(60 Count)
MOdEL NO. q85-7000
LIGHT-WEIGHT quArTErFOLd
(90 Count)
MOdEL NO. q85-7500
SUPER STRENGTH INTERFOLD
(126 Count)
MOdEL NO. q85-8000
LIGHT-WEIGHT INTErFOLd
(135 Count)
MOdEL NO. q85-8500
Sheet Size:
12-1/2 x 13
(138mm x330mm)
Sheet Size:
12-1/2 x 13
(138mm x 330mm)
Sheet Size:
9-1/2 x 16-1/2
(241mm x419mm)
Sheet Size:
9-1/2 x 16-1/2
(241mm x419mm)
Sheet Per Case: 720 Sheet Per Case: 1080 Sheet Per Case: 1008 Sheet Per Case: 1080
Case Quantty: 12 Case Quantty: 12 Case Quantty: 8 Case Quantty: 8
Case Weight: 15lbs (7kg) Case Weight: 15lbs (7kg) Case Weight: 18lbs (8kg) Case Weight: 20lbs (9kg)
Wipers Contain
25%
Recycled Fibers
go green
CHG