Вы находитесь на странице: 1из 7

2/7/2014 patinas | metal+mettle

https://metalandmettle.wordpress.com/tag/patinas/ 1/7
metal+mettle
a goldsmith at her bench: thoughts, tips & inspiration
TAG ARCHIVES: PATINAS
A blush of red in the studio
D.Brchault. Bowl, copper, patina. Dia.: 9.5 cm
As I walk through the neighbourhood these days, I notice the first blushing trees. So many shades of red:
burgundy, crimson, vermillion, even some magenta and some rusty reds too. I enjoy these rich and
vibrant colours and I always have the urge to run to my studio and add splashes of colours to my
jewellery.
2/7/2014 patinas | metal+mettle
https://metalandmettle.wordpress.com/tag/patinas/ 2/7
The palette of a metalsmith does not have to be limited to a few muted shades of silver and gold. Metals
like copper, brass, and bronze lend themselves particularly well to a wide variety of colours (or patinas)
and can open up all kinds of possibilities. Metal patination has been used in different parts of the world
for a very long time. Years ago, Ayako Kuroki, a distinguished goldsmith and teacher from Tokyo, Japan,
told me about hiirodo the red copper patina used in traditional Japanese metalwork. Here is an example
of tsuba (sword guards) with a deep maroon red copper patina:
Tsubas (Asian Art Museum, San Francisco)
Photo : Wikipedia Commons
Several types of methods can be used to colour metal, depending on the colours you want to obtain
heat or chemicals, or a combination of both. For now, lets deal with these rich and vibrant red autumn
colours (I will talk about the greens, and the blues in another post). Here is how you can incorporate
them into your work. Note that these recipes will only work with copper.
Remember to wear goggles, and make sure there is sufficient ventilation in your studio.
- Heat up the copper with the torch to a high temperature (until the metal is red hot).
- Quench immediately in a boiling water and salt solution (Salt/water solution: 3 tablespoons salt to 3
cups water).
2/7/2014 patinas | metal+mettle
https://metalandmettle.wordpress.com/tag/patinas/ 3/7
This creates a deep brick red patina:
Depending on the intensity of the flame, or how long the metal is heated up, youll get darker shades of
red or purplish red. If the metal is heated up for a bit longer, this can produce a marbled effect of red and
black,
2/7/2014 patinas | metal+mettle
https://metalandmettle.wordpress.com/tag/patinas/ 4/7
or a smoky effect like this:
Heating up the metal and quenching it in boiling water without salt will produce some rich tones of red as
well, but generally more on the rusty or orangy side:
Here is another recipe:
First, coat the metal with a mixture of borax flux and water, and heat up with the torch. Quench in boiling
water. Usually the more interesting colours appear on the back side of the sheet. Depending on what
type of flux is used (borax cone ground, and mixed with water, or liquid flux like Batterns), youll get
various results, from a deep burgundy with streaks of orange to a more mottled pattern:
2/7/2014 patinas | metal+mettle
https://metalandmettle.wordpress.com/tag/patinas/ 5/7
And for a different mottled effect, try sprinkling salt on the metal as you are heating it up. Keep the flame
on only until the grains of salt melt, then quench in boiling water right away. Results vary. On this sample,
there are intricate patterns of purple and rose tones mixed with some smoky greys.
Sometimes, I like to texture the metal before coloring it; it adds more depth and another layer of interest
to the design. There are many types of surface treatments available. In these examples, I used etching
and roll-printing:

0

Stumble
2/7/2014 patinas | metal+mettle
https://metalandmettle.wordpress.com/tag/patinas/ 6/7
Important note: Dont pickle your metal, as the pickling solution would remove the patina!
This heat patina is stable and fairly tough, so it does not really require much protection, especially if the
patinated metal is in a recessed area that will prevent scratches. Otherwise a thin coat of soft beeswax will
work well.
Now, if you consider yourself a control freak, these techniques are probably not for you! As with most
patinas, results are not always consistent, and are difficult to predict, but thats the beauty of it, and for
me thats the fun of it too. Factors such as the gauge of the metal, the intensity of the flame, or the
temperature of the water will affect the results, so keep experimenting!
Share this:
Twitter Facebook Pinterest Email Tumblr Google More
This entry was posted in how-to and tagged copper, Dominique Brechault, fall colours, heat patina, how-
to, jewelry, metal coloring, metal work, metalsmithing, patinas, red on October 20, 2012
[https://metalandmettle.wordpress.com/2012/10/20/a-blush-of-red-in-the-studio/] .

Like
5 bloggers like this.

Follow
Follow metal+mettle
Get every new post delivered
to your Inbox.
Join 78 other followers
Enter your email address
Sign me up
Powered by WordPress.com
2/7/2014 patinas | metal+mettle
https://metalandmettle.wordpress.com/tag/patinas/ 7/7

Вам также может понравиться