0 оценок0% нашли этот документ полезным (0 голосов)
953 просмотров1 страница
This document provides engine coolant refill specifications and procedures for different Honda engine models. It lists the refill capacities in liters for the H23Al and H22Al engines, both for manual and automatic transmissions. It also provides instructions for loosening the air bleed bolt, filling the radiator, bleeding air from the system, checking for leaks, and draining and refilling the coolant.
This document provides engine coolant refill specifications and procedures for different Honda engine models. It lists the refill capacities in liters for the H23Al and H22Al engines, both for manual and automatic transmissions. It also provides instructions for loosening the air bleed bolt, filling the radiator, bleeding air from the system, checking for leaks, and draining and refilling the coolant.
This document provides engine coolant refill specifications and procedures for different Honda engine models. It lists the refill capacities in liters for the H23Al and H22Al engines, both for manual and automatic transmissions. It also provides instructions for loosening the air bleed bolt, filling the radiator, bleeding air from the system, checking for leaks, and draining and refilling the coolant.
Manual : 3.8 X (4' O US qt, 3.3 l mp qrl Automati c: 3.7 t {3.9 US qt, 3.3 l mp qt} H22Al engi no: Manuaf : 4.O f 9.2 US qt, 3' 5 l mp qt) Loosen the air bleed bolt in the thetmostat housing, then fi l l the radi ator to the bottom of the ti l l er neck wi th the cool ant mi xtu.e. Ti ghten the bl eed bol t as soon as coolant stans to run out in a steadv stream wi thout bubbl es. BLEED BOLT 60 N.m {6.0 kg-m, 43 lb-ft} Applv liquid gasket to the bol t threads when i nstal l i ng. 1O. Wi th the radi ator cap oft, start the engi ne and l et i t run unti l warmed up (Radi ator fan goes on at l east twi ce). Then, i f necessary, add more cool ant mi x to bring the level back up to the bottom ot the filler neck. 11. Put the radi ator cap on ti ghtl y, then run the engi ne agai n and check tor l eaks. 10- 6 Radiator Engine Coolant nefill\ and Bleeding CAUTlOttl: When pouting engino coolaisQgsuro to shut th6 ralay box lid and not to lst coolanl spill on tho elec- trical part6 or lh paint. lf any coolant spills, rinse it off immodiat6ly. 1. Set the heater temperature l ever or conttol di al to maxamum heat. 2. Remove the engi ne spl ash shi el d. 3. When the radi ator i s cool , remove the radi ator cap. Loosen the drai n pl ug, and drai n the cool ant. 4. Remove the drai n bol t trom the rear si de of the cyl i nder bl ock to drai n the bl ock and heater, 5. Appl y l i qui d gasket to the drai n bol t threads, then reinstall the bolt with a new washer and tighten it securel y. 6. Ti ghten the radi ator drai n pl ug securel y. 7, Remove, drai n and rei nstal l the reservoi r. Fi l l the tank haltway to the MAX mark with water, then up to the MAX mark wi th anti -freeze. 8. Mi x the recommended anti -freeze wi th an equal amount ol water i n a cl ean contai ner. NOTE: a Use onl y genui ne Honda anti -Jreeze/cool ant. a Fof best corrosion Drotection, the coolant concen- trati on must be mai ntai ned year-round at 50 mi ni mum. Cool ant concentrati ons l ess than 50% may not provide sutficient protection against cor- rosi on or treezi ng. a Coolant concentrations greater than 60% will im- paif cooling efficiency and are not recommended. CAUTION: a Do not mix dilferent brands of anti-freoze/ cool ants. a Do not uso additional rust inhibitors or anti-rust products; they may not be compatible with tho gnuine coolant. Engine Coolant Refill Capacity: including reservoir {0.6 t {0.6 US qt, 0.5 l mp qt}l and heatar {0.6 f (o.6 US qt, 0.5 l mp qt)| . F22Al engi ne: Manual : 3. 5 I ( 3. 7 US qt , 3. 1 l mp qt ) Automati c: 3.4 f {3.6 US qt, 3.0 l mp qtl DRAII{ BOLT