Академический Документы
Профессиональный Документы
Культура Документы
= 0.45 f
c
= 12.6 N/mm
2
Shear stress limit
= 1.2 f
= 6.35 N/mm
2
Modulus ratio n = 8
1.4.3 Corrugated steel sheet
Class of structural steel ASTM A659 Gr. 80 or equivalent
Specified minimum yield stress F
y
= 550 N/mm
2
2.0 LOAD ANALYSIS
Concrete D
1
= 4.1 kN/m
2
Corrugated sheet D
2
= 0.1 kN/m
2
Tile flooring D
3
= 0.6 kN/m
2
Live load L = 1.0 kN/m
2
Doc. no. MD1-0-V-360-07-00725 REV. A
Pag. 5 di 19
CRI 0280725 rev.A 31.01.2013
Combining factored loads
Load combination 1 (COMB 1) 1.2 DEAD + 1.6 L
3.0 CHECK OF CORRUGATED SHEET DURING CONSTRUCTION
The corrugated sheets are supported by the secondary steel structure of the roof. The
cross section is shown in fig. 2.
Fig. 2 Corrugated sheet cross section
The total load during the construction phase is equal to:
1.2 D + 1.6 L = 1.2 (D
1
+ D
2
) + 1.6 L = 1.2 (4.1 + 0.1) + 1.6 x 1.0 = 6.64 kN/m
2
The live load is representing the load due to the personnel working and equipment required
for the concreting activities.
A unit width of slab (1 m) is considered in the following calculations.
The uniformly distributed load is then:
p = 6.64 kN/m
2
x 1.0 m = 6.64 kN/m
Three load cases are considered for the check:
Case A: two simple supports beam (par. 3.1)
Case B: three simple supports beam with asymmetric load (par. 3.2.1)
Case B2: three simple supports beam with symmetric load (par. 3.2.2)
3.1 Two simple supports beam (case A)
Fig. 3 Corrugated sheet cross section
Doc. no. MD1-0-V-360-07-00725 REV. A
Pag. 6 di 19
CRI 0280725 rev.A 31.01.2013
The max. positive bending moment is equal to:
M
pl
6.64 1.775
8
2.62 kNm
3.2 Three simple supports beam with asymmetric load (case B)
Two load distribution are considered for this case, depending on whether the load is
symmetric or not.
3.2.1 Load case B1: asymmetric load
Fig. 4 Load case B1 load scheme and bending moment distribution
The maximum bending moments are calculated throughout a straight-line interpolation of
the values contained in the Attachment 2 Bending moment for asymmetric load.
l 1775 mm
l 1725 mm 0.972
Negative bending moment at node 1:
M
pl
1.32 kNm
Support reaction at node 2:
Y
x
px
2
The location of the maximum value of bending moment is calculated by setting the first
Doc. no. MD1-0-V-360-07-00725 REV. A
Pag. 7 di 19
CRI 0280725 rev.A 31.01.2013
derivative (shear force) equal to zero:
Y
px 0
Y
5.150
6.64
0.775m
M
2
1.997 kNm
3.2.2 Load case B2: symmetric load
Fig. 5 Load case B2 load scheme and bending moment distribution
The maximum bending moments are calculated throughout a straight-line interpolation of
the values contained in the Attachment 3 Bending moment for symmetric load.
l 1775 mm
l 1725 mm 0.972
Negative bending moment at node 1:
M
pl
2.531 kNm
Max bending moment in span I
M
pl
1.381 kNm
Max bending moment in span II
M
pl
1.506 kNm
3.3 Conclusion
Considering all three cases, the maximum bending moments are:
Doc. no. MD1-0-V-360-07-00725 REV. A
Pag. 8 di 19
CRI 0280725 rev.A 31.01.2013
M
2.531 kNm
M
2.620 kNm
3.4 Check of stress
The section modulus and material properties can be found in Attachment 1 Steel deck data
sheet, for the 1.0 mm thickness case.
Z 22206 mm
plastic modulus
f
M
Z
2.620 10
22206
118.0 N/mm
550.0 /mm
3.5 Check of deflection
p 5.2 kN/m (distributed load in operating conditions)
J 526562.5 mm
f
5
384
pl
EJ
5
384
5.2 1775
200000 526562.5
6.38 mm
The deflection is lower than the common practice recommended value of 1/200 of the span
(which is equal to 8.88 mm).
4.0 CHECK OF CONCRETE SLAB
The typical cross section of the slab cast on the corrugated sheets has shown in Fig. 6.
Fig. 6 - Roof slab cross section
The design of the roof slab cast on corrugated sheets has ben carried out considering a T-
Shaped beam having a width of 240 mm as shown in fig. 7.
Doc. no. MD1-0-V-360-07-00725 REV. A
Pag. 9 di 19
CRI 0280725 rev.A 31.01.2013
Fig. 7 - T-beam cross section
The total load during the operation phase is equal to:
p 1.2 D
The uniformly distributed load is then:
p
7.36kN
m
pl
1.77 1.775
8
0.70 kNm
Maximum negative bending moment:
M
pl
0.67 kNm
4.1 Check of stress Positive bending moment
The check of the stress due to the positive bending moment has been carried out
considering the T-shaped beam shown in the previous figure.
The contribution of the corrugated steel sheet is not considered for the check. It is also
assumed that the neutral axis lean within the upper part of the slab (y < 99 mm).
b 240 mm
b
120 mm
d 150 25 125 mm
d 25 mm
A
78.5 mm
78.5 mm
Doc. no. MD1-0-V-360-07-00725 REV. A
Pag. 10 di 19
CRI 0280725 rev.A 31.01.2013
d A
d A
1
d
1
125
0.60
h b
78.5 78.5
150 120
0.0087
y n
d 1 1
2
n
8 0.0087 125 1
1
2 0.60
8 0.0087
28.46 mm 99
J
b y
3
n A
d y
n A
y d
120 28.46
3
8 78.5 125 28.46
8 78.5 28.46 25
6.78 10
mm
M y
J
0.70 10
28.46
6.78 10
2.93 Nmm
12.6 N/mm
n M d y
J
8 0.70 10
125 28.46
6.78 10
79.74 N/mm
165.0 /mm
4.2 Check of stress Negative bending moment
The check of the stress due to the negative bending moment has been carried out
considering the following simplifications (conservative approach):
The D10 square mesh is not taken into account
A beam rectangular section having a width equal to 120 mm has been used for the
calculation
b 120 mm
d 150 25 125 mm
d 25 mm
d A
d A
1
d
1
125
0.60
h b
78.5 78.5
150 120
0.0087
y n
d 1 1
2
n
8 0.0087 125 1
1
2 0.60
8 0.0087
28.46 mm
Doc. no. MD1-0-V-360-07-00725 REV. A
Pag. 11 di 19
CRI 0280725 rev.A 31.01.2013
J
b y
3
n A
d y
n A
y d
120 28.46
3
8 78.5 125 28.46
8 78.5 28.46 25
6.78 10
mm
M y
J
0.67 10
28.46
6.78 10
2.81 Nmm
12.6 N/mm
nM d y
J
8 0.67 10
125 28.46
6.78 10
76.32 Nmm
165.0 mm
4.3 Check of stress Shear
The maximum shear stress is located at the supports and is equal to:
V
pl
2
1.77 1.775
2
1.571 kN
z 0.9 d 0.9 150 25 112 mm
b 120 mm
V
b z
1.571 1000
120 112
0.117 N/mm
6.35 /mm
Doc. no. MD1-0-V-360-07-00725 REV. A
Pag. 12 di 19
CRI 0280725 rev.A 31.01.2013
ATTACHMENT 1: STEEL DECK DATA SHEET
Doc. no. MD1-0-V-360-07-00725 REV. A
Pag. 13 di 19
CRI 0280725 rev.A 31.01.2013
Doc. no. MD1-0-V-360-07-00725 REV. A
Pag. 14 di 19
CRI 0280725 rev.A 31.01.2013
Doc. no. MD1-0-V-360-07-00725 REV. A
Pag. 15 di 19
CRI 0280725 rev.A 31.01.2013
Doc. no. MD1-0-V-360-07-00725 REV. A
Pag. 16 di 19
CRI 0280725 rev.A 31.01.2013
Doc. no. MD1-0-V-360-07-00725 REV. A
Pag. 17 di 19
CRI 0280725 rev.A 31.01.2013
Doc. no. MD1-0-V-360-07-00725 REV. A
Pag. 18 di 19
CRI 0280725 rev.A 31.01.2013
ATTACHMENT 2: BENDING MOMENT FOR ASYMMETRIC LOAD
Doc. no. MD1-0-V-360-07-00725 REV. A
Pag. 19 di 19
CRI 0280725 rev.A 31.01.2013
ATTACHMENT 3: BENDING MOMENT FOR SYMMETRIC LOAD