0 оценок0% нашли этот документ полезным (0 голосов)
320 просмотров2 страницы
This document provides specifications for Outokumpu's continuously cast stainless steel slabs, blooms, and billets. It outlines the dimensions and tolerances for length, width, weight, and surface condition. Slab thickness can range from 170-300mm, widths from 950-1575mm, and lengths from 3200-11000mm. Bloom thickness is 300mm, widths range from 400-1500mm, and lengths are between 4000-12000mm. Billets are available in nominal dimensions of 127x127mm, 140x140mm, and 150x150mm and can range from 3600-12000mm in length. Outokumpu specializes in stainless steel and aims to be
This document provides specifications for Outokumpu's continuously cast stainless steel slabs, blooms, and billets. It outlines the dimensions and tolerances for length, width, weight, and surface condition. Slab thickness can range from 170-300mm, widths from 950-1575mm, and lengths from 3200-11000mm. Bloom thickness is 300mm, widths range from 400-1500mm, and lengths are between 4000-12000mm. Billets are available in nominal dimensions of 127x127mm, 140x140mm, and 150x150mm and can range from 3600-12000mm in length. Outokumpu specializes in stainless steel and aims to be
This document provides specifications for Outokumpu's continuously cast stainless steel slabs, blooms, and billets. It outlines the dimensions and tolerances for length, width, weight, and surface condition. Slab thickness can range from 170-300mm, widths from 950-1575mm, and lengths from 3200-11000mm. Bloom thickness is 300mm, widths range from 400-1500mm, and lengths are between 4000-12000mm. Billets are available in nominal dimensions of 127x127mm, 140x140mm, and 150x150mm and can range from 3600-12000mm in length. Outokumpu specializes in stainless steel and aims to be
Slab thickness (mm) Slab width (mm) Production length (mm)
170 950 - 1575 4000 - 11000
200 950 - 1575 4000 - 11000 300 950 - 1575 3200 - 6500 Slab Cold Slab dimensions Slab tolerances Length: Te actual delivered slab length will not deviate from the ordered slab length by more than 50mm (apart from the last slab of a cast or sequence). Weight: Te actual weight of an individual delivered slab will not deviate from the calculated slab weight in the order by more than 200kg (apart from the last slab of a cast or sequence). Width: Te actual delivered slab width will not deviate from the ordered slab width by more than 20mm. Slab surface condition Slabs are supplied in either ground or black condition as agreed with the customer. Standard Outokumpu practice is to grind the front and back slabs from each cast, and to grind slabs in the case of certain grades and processing restrictions. Bloom thickness (mm) Bloom width (mm) Production length (mm) 300 400 4000 - 12000 Bloom Cold Bloom dimensions Bloom tolerances Length: Te delivered bloom length will not deviate from the ordered bloom length by 50mm (apart from the last bloom of a cast or sequence). Weight: Te weight of an individual delivered bloom will not deviate from the calculated bloom weight in the order by more than 50kg (apart from the last bloom of a cast or sequence). Bloom surface condition Blooms are supplied in the unground condition. www.outokumpu.com Continuously Cast Stainless Steel Slab, Bloom & Billet Slab length is limited to a maximum of 15000mm and slab weight is limited to a maximum of 30 tonnes. slab data sheet V16:Layout 1 30/10/09 16:15 Page 1 www.outokumpu.com Stainless Slab, Bloom & Billet 2 Outokumpu Long Products Billet tolerances Length: Te nominal tolerance on billet length is 50mm. Where a length range is specifed the delivered lengths shall be within this range. No lengths shall be delivered below the minimum quoted. Where billets are ordered with a primary length requirement wherever possible a secondary acceptable short length should be specifed to optimise cast weight and/or cut backs for quality reasons. (Te proportion of shorts shall not exceed 10% without prior approval). Billet surface condition Billets will normally be supplied as ft for purpose, for example, free from surface defects which will be detrimental after reheating and rolling. Defects present in the cast billet may be removed by spot grinding, corner grinding or full grinding depending on the severity of the defect and at the discretion of the supplier. Tolerances shown are for guidance only - individual customer requirements should be specifed on customer orders. Billet nominal dimension (mm) Billet Length (mm) 127 x 127 3600 - 12000 140 x 140 3600 - 12000 150 x 150 3600 - 12000 Billet Billet dimensions Outokumpu is a global leader in stainless steel. Our vision is to be the undisputed number one in stainless, with success based on operational excellence. Customers in a wide range of industries use our stainless steel and services worldwide. Being fully recyclable, maintenance-free, as well as very strong and durable material, stainless steel is one of the key building blocks for a sustainable future. What makes Outokumpu special is total customer focus all the way, from R&D to delivery. You have the idea. We offer world-class stainless steel, technical know-how and support. We activate your ideas. Information given in this brochure may be subject to alteration without notice. Care has been taken to ensure that the contents of this publication are accurate but Outokumpu and its subsidiaries do not accept responsibility for errors or for information which is found to be misleading. Suggestions for or descriptions of the end use or application of products or methods of working are for information only and Outokumpu and its subsidiaries accept no liability in respect thereof. Before using products supplied or manufactured by Outokumpu or its subsidiaries, the customer should satisfy themselves of their suitability. 1 3 9 1 E N - G B : 1 R a r e C r e a t i v e G r o u p , U K . N o v e m b e r 2 0 0 9 . slab data sheet V16:Layout 1 30/10/09 16:15 Page 2