Should not moT 2. Frequency: SOR 3. Rated volta@ew .380v, 23Ov/400v, 230v/460v (oonnection type Y/ A, YY/Y) .. . , 4 . Insulation cI&& P, protection alass:IP65. rorking type: S1 oundings should be-20' -+40 and Altitude 111. Installation 1. Before using, check up the vibrator whether it is affected during transportation or with damp and whether the bolt is loose or not. 2. Check up the nameplate whether it is up to the requirement or not. 3. It must be installed on glazed fixed flat without any pore and cranny. 4. The bottom bolt should be fixed with lock measure to prevent loosing. 5. It' S better to chain with the hole beside the terminal box to prevent dropping of vibrator for the loosing of bottom bolt, when the installation height is more than 1 meter. IV. Connection of vibrator 1. Connection according to the wiring diagram under the terminal cover. 2. Put the power cables thr,ough Locknut, then connect the wires to the corresponding terminal columns and assure the distance bet- ween surfaces of two lead wires is more than 8mm. 3. Power cables should be four cores(3-phase) or three cores (single phase) with one green-yellow for grounding. The spec of selecting cable wire as the following list: 4. The green-yellox \vire must be grounding for sure to avoid electric shock b - arong connect ion. r - 1 - . 1 . . C . ? . , S 3 . . Namcplate current (.A) Section area (mm:) 3 . ine appliea capacitor or single-pnase vibrator snoula De same as the nameplate indicated, the Outer accessory capacitorshould be connec~ed by user themselves. 6. Over loading and short circuit safeguard should be f ixed wtien using 3.5G8LG5.3 1. 5 <l . 8 O . 5 \-i bx-aror. Connecrion illustration for single-phase vibrator 1.8G8LG3.5 1. O 4. The green-yel los- nire must be grounding for sure to avoid electric shock by a-rong connection. r nl - . , . . - . 3 . , m - . . 3 . ine appliea capacitor o1 single-pnase vibrator snoula t~e same as 3.5<&<5.3 1 . 5 Namcplate current (.%) Section area ( mm3 the nameplate indicatecl, the Outer accessory capacitor should be connecyed by uier themselves. 6. Over loading and shoi-t circuit safeguard should b e fixed wtien using <l . 8 O. 5 Y i bra t or. Connection illustration for single-phase vibrator 1.8<&<3.5 1. O Capacitor O W 2 z c3 - 0 "1 O -32 "2 0 - d Connection illustration for 3-phase vibrator Y/A Hl GH VOLTAGE LOW VOLTAGE Y Star Triongle Connection Connection C3 Connection illustration for 3-phase vibrator Y/A HlGH VOLTAGE LOW VOLTAGE Y Star 1 Q Connection wn c 3 0 C3 ! - ; YY Double-Star Connection a c 1 0 C3 V. Adjustment of eccentric block l . Change of Centrifugal force can be realized by adjusting the angle of eccentric block. 2. Open the top cover of vibrator. 3. Adjustment of sheet eccentric block: loosen the fixed bolt of the eccentric block, turn 180" of corresponding number of eccentric block according to requirement then turn the bolt fixed. (The) relation between adjusting sheet number and centrifugal force , refer to the list of the following.) Note that the direction and number of the turo side of the vibralor should be the same, otherwise it will affect the work life and the vibration effect of the vibrator ! t Adj ust ment of Sheet Eccent r i c bl ock Tot al Number Reduced FC When One Pi ece Turn Over Both Si de ( %) 6 t 6 33.3 3 t 3 66 9 t 9 22.2 5 t 5 40 1 1 t 1 1 18.2 4. Adjustment of round eccentric block(vide illustrate) 4. 1. Loosen the bolt (no. 4) of adjustable eccentric block (no. 3) to * be turned freely on axes. It is unnecessary to take down the fasteners of the tnro sides of the axes and loosen the bolt of fixed eccentric h block (no. 6) near top cover. Do not take down rivet of the scale when Adjusting and assure the direction and angle of the two-sidc eccentric blocks are the same, otherwise it will affect the work lif and vibration offect of the vibrator! 4.2.Adjust eccentric block according to the needed centrifugal force. 1 The centrifugal force is maximal when the centerline of eccentric block notch (no. 5) points to 100% of the centrifugal force dial (no. 1) and centrifugal force is zero when point to %. 4.3. If the max. centrifugal force is Fc, the centrifugal force is i Fc*80% when the centerline of eccentric block notch (no. 5) points tc 80% of the centrifugal force dial (no. 1). P- 4.4. Screwdown the two-side bolts of the eccentric block, the screw moment is about 2. 8kg. m. 1 o 5. Adjustment of fan-shaped eccentric block (vide illustrate) 5.1. Loosenthe bolt (no. 4) of adjustable eccentric block (no. 3) to be turned freely on axes. It is unnecessary to take down the fasteners of the tno sides of the axes and loosen the bolt of fixed eccentric block near top cover. Do not take down the rivet of the scale adjusting and assure the direction and angle of the two-side eccentric blocks are the same, otherwise it will affect the work life and vibration effect of the vibrator! 5.2. Adjust eccentric block according to the needed centrifugal force. The centrifugal force is maximal when adjustable eccentric block get superposition with fixed eccentric block. Then side of adjustable eccentric block points to 100% of the centrifugal force dial (no. 1) is the datum line side and centrifugal force is zero when the datum line side pointing to %, 5.3. If the max. centrifugal force is Fc, the centrifugal force is Fc*80% when datum line side of eccentric block points to 80% of the centrifugal f orce dial. 5.4. Screwdown the two-side bolts of the eccentric block, the screw moment is about 2.8kg. m. 6. fixing the top cover. 7. The adjustment parameters above are under the working cndition of 50Hz. When the position of the two-side eccentric blocks are the sam the vibrating force of 50Hz is 70% times of 60Hz. 12 INDICATOR FC FcX80% Store and Transportation 1. The vibrator we manufactured is packed with plastic bag inside and carton outside. Advising not unpack and keep dryness and avoid temperature of sharp change when store it. 2. Do not inverse the vibrator during storing or transportation. NOTE: The instruction will be modified as the development of technology without notifying. The updated is correct.