Академический Документы
Профессиональный Документы
Культура Документы
(b)
If L is the charge per unit length; obtain an expression for the electric field produced by a line charge (infinitely large), placed along the z-axis, at some point P with
position vector r
(12 MARKS)
(c)
Q.2 (a) The OLTF of a unity feed back control system is given as G s
(8 MARKS)
16
s s 4
(12 MARKS)
Determine
(i) The damped frequency of oscillations, peak overshoot and steady state error for
unit ramp input
(ii) If the damping factor is to be adjusted to 0.8 using derivative output controller.
Calculate the controller constant
(b)
s 3 3s 2 K 2 s 3K 0
Plot the root locus with K varies from 0 to .
(c)
(12 MARKS)
X A X BU
(8 MARKS)
Q.3(a) Derive the expression to determine the steady state error for unit step, unit ramp and
unit parabolic input for Type-0, Type-1 and Type-2 system
(12 MARKS)
(b)
dy
3y 2 u t
dt
dt
and determine the state transition matrix
(10 MARKS)
(c)
ENGINEERS ZONE
IES / GATE / PSU
(c)
(10 MARKS)
(6 MARKS)
(ii) The intrinsic carrier concentration in a piece of Si at 300K is 1.5 1010 /cm 3
Determine the donor concentration required if the required conductivity is
0.9 1 cm 1 Also determine the hole concentration. The mobility of electron is
3900 cm 2 / V s
(5 MARKS)
PART-C
Q.5(a) For a series RLC circuit derive the expression for Band width & selectivity. Discuss
the pratical application of selectivity in RLC circuit.
(12 MARKS)
(b)
(12 MARKS)
The switch S was in position -1 for long time. At t 0 S is connected to position -2 and
after 500 ms S is connected to position -3. Find i t for t>500 ms
(c)
Synthesize the given network function into Cauer-I & Cauer-II forms.
Y s
s s2 2
s 2 1s2 3
(12 MARKS)
Q.6(a) Determine the maximum power consumed in the load resistance R L . Derive the
expression used.
(12 MARKS)
ENGINEERS ZONE
IES / GATE / PSU
(5 MARKS)
Define the image impedance for a 2-port network Determine their values in terms of
ABCD parameters
(9 MARKS)
PART-D
Q.7(a) A schering Bridge is used for measuring the power loss in dielectrics. The speciman
are in the form of dises 0.5 cm thick having dielectric constant of 4. The area of each
3
electrode is 628 cm and loss angle is 6 for a frequency of 50 Hz. The values of fixed
resistor & fixed capacitor is bridge are 800 and 40 pF respectively. Determine the
values of variable resistance & capacitor required. Derive the expression used. Also
draw the phasor diagram under balanced conditions
(12 MARKS)
(b)
Why dArsonal Galvanometer is used in PMMC. Explain the woking of elctronic voltmeter using bridge circuit for full wave rectification.
A sawtooth voltage of peak valud of 100 V and a time period of 5 sec is applied to the
EVM using full wave retification. Calculate the error in reading if scale is calibrated
in terms of rms of sine wave.
(12 MARKS)
(c)
Discuss the basic principle of Digital Frequency Meter. Describe the change in the
settings required for different range of frequencies.
(8 MARKS)
Q.8(a) Explain the basic principle of operation of Moving Iron Instrument. Derive the torque
equation.
(8 MARKS)
(b)
Discuss the concept of 3 power measurement using two wattmeter method. Also
discuss the result at different power factors in case of balanced load.
(12 MARKS)
(c)
Q.9(a) (i) Why damping torque is provided in Indicating Instruments. Discuss the type of
damping required in PMMC.
(6 MARKS)
(ii) Discuss the working of an LVDT transducer
(6 MARKS)
(b)
(c)
ENGINEERS ZONE
IES / GATE / PSU
(10 MARKS)