Академический Документы
Профессиональный Документы
Культура Документы
MN915001EN
ii
GridAdvisor Series II smart sensor installation instructions MN915001EN October 2014 www.cooperpower.com
Contents
SAFETY INFORMATION
Safety Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . iv
PRODUCT INFORMATION
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Acceptance and Initial Inspection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Handling and Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Standards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
INSTALLATION PROCEDURES
Installing SIM Card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Forcing Over the Air Service Provision (OTASP) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Installing Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Underground Distribution Circuits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Installation of Smart Sensor - Underground Application . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Installation of Smart Sensor - Overhead Application . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Device Activation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
LED Installation Indication . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Programming Sensor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
SUPPORT
Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
GridAdvisor Series II smart sensor installation instructions MN915001EN October 2014 www.cooperpower.com
iii
SAFETY
FOR LIFE
SAFETY
FOR LIFE
Eatons Cooper Power Systems products meet or exceed all applicable industry standards relating to product safety. We
actively promote safe practices in the use and maintenance of our products through our service literature, instructional
training programs, and the continuous efforts of all Eatons Cooper Power Systems employees involved in product design,
manufacture, marketing, and service.
We strongly urge that you always follow all locally approved safety procedures and safety instructions when working around
high voltage lines and equipment, and support our Safety For Life mission.
Safety information
The instructions in this manual are not intended as a
substitute for proper training or adequate experience in the
safe operation of the equipment described. Only competent
technicians who are familiar with this equipment should
install, operate, and service it.
Safety instructions
WARNING
Before installing, operating, maintaining, or testing
this equipment, carefully read and understand
the contents of this manual. Improper operation,
handling or maintenance can result in death, severe
personal injury, and equipment damage.
G101.0
WARNING
WARNING
WARNING
DANGER
CAUTION
Indicates a potentially hazardous situation which, if
not avoided, may result in minor or moderate injury.
CAUTION: Indicates a potentially hazardous situation
which, if not avoided, may result in equipment
damage only.
iv
DANGER
GridAdvisor Series II smart sensor installation instructions S1150-20-1 June 2014 www.cooperpower.com
Introduction
Installation procedures
Additional information
These instructions cannot cover all details or variations in
the equipment, procedures, or process described, nor to
provide directions for meeting every possible contingency
during installation, operation, or maintenance. For additional
information, contact your Eatons Cooper Power Systems
representative.
Handling
Quality standards
Battery Compartment
Installing battery
WARNING
Leaving sensor activated without proper charging
current source will lead to equipment (battery) damage.
G101.0
5. Re-tighten cap from 17-22 in-lbs of torque to prevent
any water ingress.
In cases where a torque wrench is not available; tighten
the cap until the gasket inside the cap makes contact
with the battery, turn another 1/2 turn to ensure proper
tightening.
GridAdvisor Series II smart sensor installation instructions MN915001EN October 2014 www.cooperpower.com
IMPORTANT
ELBOW
TIE-OFF
TAB
ELBOW
TERMINATED
NEUTRAL
WIRES
LOCATE
THE SENSOR
PORTION OF
THE FAULTED
CIRCUIT
INDICATOR
(in the outlined
area)
NEUTRAL
WIRES
A
A
Figure 2. Incorrect methods of concentric Figure 3. Recommended methods of concentric neutral primary cable
preparation
neutral primary cable preparation
GridAdvisor Series II smart sensor installation instructions MN915001EN October 2014 www.cooperpower.com
. 83
m
. 83
. 9 60
15.2/26.3 kV
200 A
LOADBREAK
15.2/26.3 kV
200 A
LOADBREAK
. 83
21.
0-
LE225
D
08
-24.38
21.
21.
15.2/26.3 kV
200 A
LOADBREAK
IN
. 9 60
IN
0-
LE225
D
08
-24.38
. 9 60
IN
0-
LE225
D
08
-24.38
Figure 4. Proper installation of smart sensor on prepared conductor is shown in Figures A (left) and B (middle).
Figure C (right) shows the incorrect placement for installation.
GridAdvisor Series II smart sensor installation instructions MN915001EN October 2014 www.cooperpower.com
Load LED
Source LED
IMPORTANT
Install the sensor a minimum of ten (10) feet from any
structure on the conductor including any poles.
Device activation
Source LED
Load LED
Initialization
Initialization Failure
Initialization Complete
Successful Cellular
Activation
GridAdvisor Series II smart sensor installation instructions MN915001EN October 2014 www.cooperpower.com
Source LED
Load LED
Programming sensor
Please refer to Programming Guide S1150-20-2 for
instructions on connecting to sensor with Bluetooth
module and/or programming device with ProView NXG
software.
Support
Eatons Cooper Power Systems is proud to offer a
comprehensive collection of support resources for users
requiring additional information or assistance in the setup,
operation, and troubleshooting of GridAdvisor Series II
smart sensor and other equipment from Eatons Cooper
Power Systems.
GridAdvisor Series II smart sensor installation instructions MN915001EN October 2014 www.cooperpower.com
Compliance information
GridAdvisor
Model: GCVT3G
Contains FCCID: QIPPXS8 and QOQWT12
Contains IC: 7830A-PXS8 and 5123A-BGTWT12A
Industry Canada:
GridAdvisor Series II smart sensor installation instructions MN915001EN October 2014 www.cooperpower.com
SAFETY
FOR LIFE
Eaton
1000 Eaton Boulevard
Cleveland, OH 44122
United States
Eaton.com
Eatons Cooper Power Systems
Business
2300 Badger Drive
Waukesha, WI 53188
Cooperpower.com
2014 Eaton
All Rights Reserved
Printed in USA
Publication No. MN915001EN October 2014
(Supersedes S1150-20-1 / June 2014)