Академический Документы
Профессиональный Документы
Культура Документы
Introduction
Note: Do not perform any procedure in this Special Instruction until you have read this
information and you understand this information.
This Special Instruction provides procedures and recommendations on the preparation of
Caterpillar engines for storage up to one year.
Note: If long term storage for a period of time that exceeds one year is necessary, contact
your local Caterpillar Dealer for the preferred procedure to use in your specific case.
This Special Instruction begins by providing engine storage procedures for any
application.
General Requirements
Engine
Caterpillar recommends the use of Volatile Corrosion Inhibitors (VCI) in order to prevent
damage due to moisture during storage. These inhibitors work by evaporating inside the
engine. The inhibitors then condense over the inside surfaces. This evaporation and
condensing offers full protection to surfaces that cannot be reached with preservatives
that require a direct application. This process also assists in cleaning the engine when you
are removing the engine from storage. The volatile vapors are removed by running the
engine to operating temperature. A mineral oil base is left behind after the volatile vapors
are removed. The oil should then be drained. New oil should be added and new filters
should be installed.
Cooling System
The cooling system should be maintained with Caterpillar coolant or an equivalent.
Caterpillar coolant contains the necessary inhibitors in order to prevent corrosion and
pitting. When Caterpillar coolant is used in the proper mixture, the coolant will prevent
damage due to rust and freezing. In warm climates, the engines are stored with water in
the cooling system. In such cases, distilled water or deionized water is recommended for
use in the engine cooling system. If distilled water or deionized water is not available, use
the water that meets the minimum acceptable requirements.
Note: All Caterpillar engines that are equipped with an Air to Air Aftercooler (ATAAC)
require a minimum of 30 percent glycol to prevent water pump cavitation. When
approved water is used, the water must be treated with six to eight percent by volume
with Caterpillar Supplemental Coolant Additive (SCA). The additive is also called
Caterpillar Cooling System Conditioner. The engine should not be stored without SCA or
an equivalent.
Note: Please refer to Operation and Maintenance Manual, SEBU6251, "Water/SCA
(Supplemental Coolant Additive)". Completely fill the radiator in order to prevent rusting
at the top tank. Do not leave any exposed air space in the radiator. All exposed areas will
rust.
Necessary Equipment
Sprayer
A 1P-0540 Fuel Flow Checking Tool Group or an air compressor with a sprayer
attachment can be used to prepare the engine for storage. Change the nozzle adjustment
in order to provide either a spray or a fog pattern. The fog pattern adjustment is better if
access to components is difficult. The spray pattern is better for parts on the outside of
the engine.
Paint
Outside parts of the engine can best be protected by thorough use of a good quality paint.
Paint provides good protection for a storage period up to two years. Before painting,
thoroughly clean the engine. Read all the directions,and understand all the hazards on the
labels of any product that is used to maintain your equipment in order to avoid personal
injury. Use all the required protective equipment in order to perform the job.
Note: Refer to 143-4985 Preservation Gp for additional information.
Plastic Bags
Use black or dark plastic bags. Clear plastic bags will deteriorate over long periods of
time.
Sealing Tape
Use a sealing tape with good adhesive properties. Do not use duct tape. Duct tape will
loosen over a short period of time. Two inch wide rolls of sealing tape are recommended.
A good quality sealing tape is available from the following suppliers:
3M Product Information Center
3M Center
Building 304-01-01
St. Paul, Minnesota 55144
USA
Phone: (800) 364-3577
3M Industrial Tapes
3M Center
Building 220-8E-04
St. Paul, Minnesota 55144
USA
TARP Preservative
The preservative may be applied to any surface of the equipment, except on paint that is
not cured. The paint cures in 48 hours. The preservative, and additional information is
available from the following:
Rust Preventative
Caterpillar 450 Rust Preventative Oil can be used on all chrome surfaces of hydraulic
cylinders to minimize corrosion and pitting of the rods.
Multipurpose Grease
Use multipurpose grease such as 5P-0960 Grease Cartridge , which contains three to five
percent molybdenum disulfide that conforms to MIL-M-7866 and a suitable corrosion
inhibitor, to lubricate rod threads, ball joints, and linkages. NLGI No. 2 Grade is suitable
for most temperatures.
Filters
Refer to the parts book for your engine. The parts book will list all of the necessary part
number of filters for your specific engine application. These filters are available from
your local Caterpillar Dealer.
VCI Oil
VCI oil can be used in all types of tanks. VCI oil is an oil stabilizer and a rust
preventative. The oil can be used in a combination with any petrochemical. Apply by
using a spray pattern or a fog pattern. Caterpillar recommends the use of VCI oil in order
to prevent internal engine damage due to moisture during storage. These inhibitors act by
evaporating inside the engine, and then condensing over the inside surfaces. The process
of evaporation and condensing offers full protection to surfaces that cannot be reached
with preservatives that require an application directly. The process of evaporation and
condensing will ease cleaning the engine when the engine is removed from storage. The
volatile vapors are removed by running the engine to operating temperature. A mineral
oil base is left behind after the volatile vapors are removed. The oil should then be
drained, and new oil and filters should be installed. VCI oil should not be used at full
strength on nonferrous metals when the oil will be in direct contact or extended contact.
VCI oil must be diluted as it is recommended in the following instructions. When the
engine is being treated with VCI oil, the engine must be completely sealed when the
engine is stored. VCI oil is so volatile that any opening that is left unsealed will allow the
vapors to escape. The escape of the vapor will cause the engine to lose protection.
Volatile corrosion inhibitor (VCI), NOX-RUST VCI #10 oil or an equivalent oil provides
both liquid and vapor protection to ferrous metal surfaces against corrosion that is caused
by moisture. In a closed compartment, protection is by direct contact with VCI oil, or by
contact with VCI vapors. Contact your local supplier for a similar type of oil. Additional
information on the use of VCI oil and a list of suppliers outside the USA can be obtained
by contacting:
Rock Island Lubricants and Chemical
Customer Service
320 First Street Rock Island, Illinois 61201
USA
Phone: (309) 788-5631Fax: (309) 786-3946
Diesel Fuel
Diesel fuel that is left in fuel tanks and fuel injection systems will sometimes cause
problems due to the growth of small organisms. This may result in plugged fuel filters,
corrosion, sticking fuel pumps, or malfunctioning fuel injection valves. Draining the fuel
injection pump and refilling the fuel injection pump with Caterpillar Calibration Fluid
can minimize this problem.
Note: Calibration Fluid is available from your local Caterpillar Dealer. Caterpillar
Calibration Fluid is the preferred choice because it contains Rust and Oxidation (R&A)
inhibitors. If Caterpillar Calibration Fluid is not available, kerosene is a second
consideration. Kerosene does not contain Rust and Oxidation inhibitors and is far from
the best choice. In addition, kerosene is preferred over diesel fuel (another alternative)
because kerosene is not as prone to oxidation as diesel fuel. During long storage periods,
kerosene will not thicken as much as diesel fuel. Fuel tanks should be protected internally
with VCI oil. Then, the fuel tank should be sealed.
Engine
Storage Up To One Year
All Diesel and Natural Gas Engines
Note: If long term storage for a period of time that exceeds one year is necessary, contact
your local Caterpillar Dealer for the preferred procedure to use in your specific case. The
storage procedure should be used for all diesel engines and natural gas engines in all
applications. If an engine is not used, oil can run off the cylinder walls, piston rings, main
bearings, connecting rod bearings, the crankshaft, gears, and other parts that normally
receive lubrication. A lack of lubricant allows corrosion to begin to appear on the metal
especially in areas of high humidity (water content in the air). When the engine is started
after being stored, the metal to metal contact will cause wear before the surfaces receive
oil. To minimize this wear, use the starter to turn the engine with the throttle in the FUEL
OFF position. When oil pressure is shown on the pressure gauge, start the engine.
1. Clean the engine of any dirt, rust, grease, and oil. Inspect the exterior. Paint areas
that contain paint damage with good quality paint.
2. Remove any dirt from the air cleaner or air cleaners. Check all seals, gaskets, and
the filter element for damage.
3. Apply lubricant to all the points that are shown in the Operation & Maintenance
Manual, "Lubrication & Maintenance" chart for the equipment.
4. Drain the crankcase oil and replace the crankcase oil. Then, change the oil filter or
oil filters. Refer to the Operation & Maintenance Manual for the proper
procedure.
5. If the engine is equipped with an air starter, fill the reservoir with a mixture of 50
percent VCI oil and 50 percent engine oil.
6. Add VCI oil to the crankcase at the rate of three to four percent by volume.
Note: If the engine crankcase is full, drain enough engine oil so the mixture can
be added.
7. Remove the air filter element or air filter elements. Turn the engine at cranking
speed with the throttle control in the FUEL OFF position. Use a sprayer to add a
mixture of 50 percent VCI oil and 50 percent engine oil into the air inlet or
turbocharger inlet.
Note: The mixture of VCI oil can also be added to the inlet by removing the plug
for checking turbocharger boost pressure. The minimum application rate is 5.5
mL per L (3 oz per 1000 cu in) of engine displacement.
8. Use a sprayer to apply a mixture of 50 percent VCI oil and 50 percent engine oil
into the exhaust openings. The minimum rate of application of oil is 5.5 milliliters
per liter or 3 ounces per 1000 cubic inches of engine displacement. Seal the
exhaust pipe, and seal any drain holes that are in the muffler.
9. Remove the fuel from the secondary fuel filter housing and reinstall the spin-on
fuel filter element in order to remove any dirt and water. Only drain a fuel
injection pump that is a sleeve metered. Clean the primary fuel filter. Fill with
calibration fluid or kerosene. Install the primary fuel filter and operate the priming
pump. This will send clean oil to the secondary filter and the engine. Open the
fuel tank drain valve. Allow any water or dirt to drain from the inside of the fuel
tank. Apply a spray of 30 milliliters per 30 liters or 1 ounce per 7.5 gallons of the
fuel tank capacity in order to prevent rust in the fuel tank. Add 0.15 milliliters per
liter or .02 ounces per gallon of commercial biocide, such as Biobor JF or an
equivalent to the fuel. Apply a small amount of oil to the threads on the fuel tank
filler neck and install the cap. Seal all openings to the tank in order to prevent
evaporation of the fuel and preservative.
10. Remove the fuel nozzles or spark plugs. Apply 30 mL (1 oz) of a mixture of VCI
oil (50 percent VCI oil and 50 percent engine oil) in each cylinder. Use a bar or a
turning tool to rotate the engine slowly. This slow rotation will put the mixture of
oil on the cylinder walls. Install all fuel nozzles or spark plugs and tighten to the
correct torque.
11. Spray a thin amount of the mixture of VCI oil (50 percent VCI oil and 50 percent
engine oil) on the flywheel, ring gear teeth, and starter pinion. Install the engine
covers in order to retain the VCI vapors in the engine.
12. Apply a heavy amount of multipurpose grease (MPGM) to all outside parts that
move, such as rod threads, ball joints, linkage, etc.
Note: The minimum application rate is critical to prevent loss of protective
vapors. Install the air filter element or air filter elements and completely enclose
the element or elements with dark, plastic bags. Seal the bags with tape. Replace
the air filter covers. Place tape over all openings in order to seal VCI vapors in the
engine.
Note: Install all covers, and ensure that tape has been installed over all openings,
the air inlet, exhaust openings, the flywheel housing, the crankcase breathers,
dipstick tubes, etc. Ensure that all covers are airtight and weatherproof. Use a
waterproof weather resistant tape such as Kendall No. 231 or an equivalent. Do
not use duct tape. Duct tape will only seal for a short period of time.
13. It is best to remove the batteries, and the batteries should be used in another
application. As an alternative, place the batteries in storage. Batteries should be
periodically checked, and electrically charged if a charge is needed. If the
batteries are not removed, wash the tops of the batteries until the batteries are
clean. Apply an electrical charge to the batteries in order to obtain a specific
gravity of 1.225. Disconnect the battery terminals. Place a plastic cover over the
batteries.
13. If the engine was removed from storage and temperatures of less than 12 C (10
F) were encountered, refer toService Manual, SEBU5898, "Cold Weather
Recommendations Operation and Maintenance".
Only an operational check at the initial start is necessary before operation in Caterpillar
engines immediately after the storage of an engine. The operational check is performed in
order to ensure that the correct pressures and correct temperatures are kept in the
following systems: lubrication, cooling and fuel systems. The operational check will also
ensure that any leaks are corrected. To ensure a safe check at the initial start, use the
following procedure:
1. Turn the engine at cranking speed with the throttle in FUEL OFF position until
engine oil pressure is present.
2. Operate the engine for 10 minutes at low idle rated speed.
3. Operate the engine for 15 minutes at half rated load and 3/4 rated speed.
4. Operate the engine for 30 minutes at full rated load and full rated speed.
5. Check frequently for oil leaks, coolant leaks, and fuel leaks in the first hours of
operation. Repair any leaks as soon as detected.