Академический Документы
Профессиональный Документы
Культура Документы
ULTRASERIES
USM-1P
USM-100P
USM-100P
USM-1P
The amplifier/processing package incorporates Intelligent AC, which performs automatic voltage selection, EMI filtering, soft
current turn-on and surge suppression for
fail-safe worldwide operation.
The USM-P cabinet is constructed from premium birch plywood and covered in a black
textured hard-shell finish. Recessed handles
allow easy transit, a hex-stamped steel grille
protects the speakers, and a removable grey
foam front grille covering is included. The
enclosure can be custom painted for applications requiring specific cosmetics. USM-P
monitors can be deployed as stage wedges
or flown as sidefill or choir monitors. Two
L-Track strips on the top panel that work
with the cabinets center of gravity facilitate
angle adjustment. A bottom strip serves as
an anchor point for tilt angles. Rigging is for
single cabinet suspension only.
applications
USM-1P/USM-100P specifications
Notes:
Acoustical
Range1
Operating Frequency
Frequency Response2
Phase Response
Maximum Peak SPL3
Dynamic Range
30 Hz - 18 kHz
40 Hz - 17 kHz 4 dB
500 Hz - 16 kHz 35
132 dB
>110 dB
Coverage
USM-1P: 45 x 45; USM-100P: 100 horiz. x 40 vert.
Crossover4
USM-1P: 1000 Hz; USM-100P: 900 Hz
Transducers
Low Frequency
High Frequency
Audio Input
Type
Maximum Common Mode Range
Connectors
Input Impedance
Wiring
DC Blocking
CMRR
RF Filter
TIM Filter
Nominal Input Sensitivity
Input Level
Amplifier
Type
Output Power7
THD, IM, TIM
Load Capacity
Cooling
AC Power
Connector
Voltage Selection
Safety Agency Rated Operating Range
Turn-on and Turn-off Points
Current Draw:
Idle Current
Max Long-Term Continuous Current (>10 sec)
Burst Current (<1 sec)
Ultimate Short-Term Peak Current Draw
Inrush Current
RMS Network (optional)
PowerCon or VEAM
Automatic, continuous range from 90 V AC to 265 V AC
100 V AC - 240 V AC; 50/60 Hz
90 V AC on, no turn-off, only fuse-protect above 265 V AC8
USM-1P/USM-100P - 04.089.005.01 B
0.25 A rms (115 V AC); 0.13 A rms (230 V AC); 0.3 A rms (100 V AC)
2.8 A rms (115 V AC); 1.4 A rms (230 V AC); 3.2 A rms (100 V AC)
3.2 A rms (115 V AC); 1.6 A rms (230 V AC); 3.7 A rms (100 V AC)
5.0 A pk (115 V AC); 2.5 A pk (230 V AC); 5.8 A pk (100 V AC)
<9 A pk (115 V AC and 230 V AC)
Copyright 2005
Meyer Sound Laboratories Inc.
All rights reserved
T: +1 510 486.1166
F: +1 510 486.8356
techsupport@meyersound.com
www.meyersound.com
architect specifications
The loudspeaker shall be a self-powered stage monitor; two
models shall be available. The transducers shall consist of a 15inch diameter cone driver and a 3-inch diaphragm compression
driver on a 45-degree symmetrical or a 100-degree horizontal x
40-degree vertical horn, depending on the model.
The internal power supply shall perform automatic voltage selection, EMI filtering, soft current turn-on and surge suppression. Powering requirements shall be nominal 100, 110 or 230