Академический Документы
Профессиональный Документы
Культура Документы
608-831-2396 or 866-352-7108
About Us Contact Us
Search
Search Products
All Products
Toner
Maintenance Kits
Printers
Parts
Tech Support
Account Login
Search Support
Shopping Cart
My Account Checkout
Home
Troubleshooting
Tech Support
Support Home Page
Maintenance Kit Instructions
Other Instructions
Troubleshooting
Articles, News, Blog
Featured Articles
HP Error Codes
Entering Service Mode
Service Mode PIN Codes
Counterfeit Parts Challenge
Cold Reset Instructions
Clearing Maintenance Count
JetDirect Reference Guide
Half-Way Test
Repetitive Defect Ruler
Testimonials
Innovations From PrinterTechs
Glossary Of Terms
An NVRAM initialization reinitializes NVRAM and sets all system parameters to the factory defaults. To perform
an NVRAM initialization, turn the printer power off, then press and hold the JOB CANCEL button. Turn the
printer power back on and continue to hold the JOB CANCEL button for 20 or more seconds after all of the
LEDs come on. The NVRAM initialization starts once the JOB CANCEL button is released (any time after 20
seconds). The control panel cycles the LEDs from front to back until the NVRAM initialization is complete.
HP LaserJet 2200 series
This feature will reinitialize NVRAM and set all system parameters to the factory defaults. During the NVRAM
initilization process, all button presses will be ignored. To perform a NVRAM initialization: Turn the printer
power off. Press and hold GO. Turn the printer power back on and continue to hold GO until the Attention,
Ready, and Go lights turn on. Release GO. The device lights will begin cycling from font to rear. The NVRAM
initilization will run until completion and the device will go to the ready state.
HP LaserJet 2300 series
Before performing a hard-disk initialization, print a menu map and a configuration page. Use the information
on the configuration page to reset any customer-set printer configuration values that the hard disk initialization
procedure changes. Performing an NVRAM initialization clears the NVRAM of all control panel settings
including the following: Model number, Serial number, Service ID, usage data (such as page counts, number
of copies count, maintenance counts), Event log. To perform an NVRAM initialization, complete the following
steps: Turn off the printer, Press and hold (DOWN arrow), and turn on the printer. When all three status lights
are lit, release (DOWN arrow) and press (UP arrow), press PAUSE/RELEASE. The first item of a menu
appears, use (UP arrow) or (DOWN arrow) to scroll to NVRAM INIT, and press (SELECT).
HP LaserJet 1320 series
Only perform the following procedure if absolutely necessary. Performing an NVRAM initialization resets some
parameters that cannot be restored later. NVRAM initialization sets all default variables stored in NVRAM back
to factory default values or to a default ROM value, depending on the variable. It also performs a system reset.
NVRAM initialization resets the following: All menu settings to factory default values Factory settings such as
formatter number, page counts, and factory paper settings to perform NVRAM initialization Turn the printer off.
Press and hold down the GO button. Turn the printer on, and continue to hold the GO button for at least 20
seconds. During this process, the GO button, Attention, and Ready LEDs each turn on. Release the GO button.
The printer LEDs will begin cycling. The NVRAM unit process runs until the printer is in the ready state.
HP LaserJet 2400 series
To initialize NVRAM, Remove any installed accessories (for example, a stapler/stacker). Turn the printer off.
Turn the printer on. When the printer begins its memory count, press and hold down the up Arrow ( ) button
until all three printer control-panel lights flash once and then remain on. This might take up to 10 seconds.
Press the Down Arrow ( ) button. Press the Menu button. The display should show FULL NVRAM INIT. Press
http://www.printertechs.com/printer-troubleshooting/339-nvram-initialization-hp-laserjets
1/3
10/8/2014
http://www.printertechs.com/printer-troubleshooting/339-nvram-initialization-hp-laserjets
2/3
10/8/2014
To initialize NVRAM, turn the printer on and watch the control-panel display. When the display shows the
memory count, press and hold until all three lights on the control panel are lit. Press the UP BUTTON. Press
PAUSE/RESUME (HP Color LaserJet 4600 models) or MENU (HP Color LaserJet 4610n and 4650 models).
The message SKIP DISK LOAD appears on the control-panel display. Press UP BUTTON until NVRAM INIT is
highlighted. Press SELECT BUTTON the printer initializes NVRAM and then continues its power-on sequence.
HP Color LaserJet 4700 Series
Before initializing NVRAM, print a configuration page and a supplies status page to gather the following
information, total page count and color page count and serial number. To initialize NVRAM, turn the printer on
and watch the control panel display. When the display shows the memory count, press and hold until all three
lights on the control panel are lit. Press UP BUTTON. Press Menu. The message SKIP DISK LOAD displays
on the control panel. Press until NVRAM INIT is highlighted .Press SELECT BUTTON The printer initializes
NVRAM and then continues its power-on sequence.
HP Color LaserJet 5500
Before initializing NVRAM, print a configuration page and a supplies status page to gather the following
information, total page count and color page count transfer kit count fuser kit count serial number. To initialize
NVRAM Turn the printer on and watch the control panel display, when the display begins showing the memory
count, press and hold DOWN BUTTON until all three lights on the control panel are lit. Press the UP BUTTON.
Press PAUSE/RESUME. The display should show SKIP DISK LOAD. Press UP BUTTON until NVRAM INIT is
highlighted. Press the SELECT BUTTON. The printer will initialize NVRAM and then continue its power-on
sequence.
http://www.printertechs.com/printer-troubleshooting/339-nvram-initialization-hp-laserjets
3/3