Вы находитесь на странице: 1из 7

Router con0 is now available

Press RETURN to get started.

Router>
Router>en
Router#conf t
Enter configuration commands, one per line. End with CNTL/Z.
Router(config)#name CLK-COR-QA-1
^
% Invalid input detected at '^' marker.
Router(config)#host na
Router(config)#host nam
Router(config)#host?
hostname
Router(config)#host CLK-COR-QA-1
CLK-COR-QA-1(config)#switch virtual domain 100
Domain ID 100 config will take effect only
after the exec command 'switch convert mode virtual' is issued
CLK-COR-QA-1(config-vs-domain)#switch 1
CLK-COR-QA-1(config-vs-domain)#exit
CLK-COR-QA-1(config)#interface port-channel 10
CLK-COR-QA-1(config-if)#switch virtual link 1
CLK-COR-QA-1(config-if)#no shut
CLK-COR-QA-1(config-if)#exit
CLK-COR-QA-1(config)#int
CLK-COR-QA-1(config)#interface te1/1
CLK-COR-QA-1(config-if)#channel-group 10 mode on
CLK-COR-QA-1(config-if)#no shut
CLK-COR-QA-1(config-if)#interface te5/1
CLK-COR-QA-1(config-if)#channel-group 10 mode on
CLK-COR-QA-1(config-if)#no shut
CLK-COR-QA-1(config-if)#do show platform hardware pfc mode
PFC operating mode : PFC4
CLK-COR-QA-1(config-if)#switch convert mode virtual
^
% Invalid input detected at '^' marker.
CLK-COR-QA-1(config-if)#exit
CLK-COR-QA-1(config)#exit
CLK-COR-QA-1#
*Dec 2 19:20:19.871: %SYS-5-CONFIG_I: Configured from console by console
CLK-COR-QA-1#switch convert mode virtual
This command will convert all interface names

to naming convention "interface-type switch-number/slot/port",


save the running config to startup-config and
reload the switch.
NOTE: Make sure to configure one or more dual-active detection methods
once the conversion is complete and the switches have come up in VSS mode.
Do you want to proceed? [yes/no]: yes
Converting interface names
Building configuration...
[OK]
Saving converted configuration to bootdisk: ...
Destination filename [startup-config.converted_vs-20141202-192103]?
7527 bytes copied in 0.444 secs (16953 bytes/sec)
*Dec 2 19:22:12.307: %SYS-5-RELOAD: Reload requested by Exec. Reload Reason: Co
nversion.
Cisco Governator Rommon version 1.1
System Initializing ...
System Bootstrap, Version 15.1(02)SY01 [ Rel 1.1], RELEASE SOFTWARE
Copyright (c) 1994-2013 by cisco Systems, Inc.
Current image running: Governator Boot Rom :Upgradable Region
Last reset cause: Software Reset, reset code 0x4
Governator platform with 2097152 Kbytes of main memory
No valid BOOT image found
Final autoboot attempt from default boot device...
#Booting c6880x-ipservicesk9-mz.SPA.151-2.SY3.bin ...
################################################################################
################################################################################
################################################################################
################################################################################
################################################################################
################################################################################
################################################################################
################################################################################
################################################################################
################################################################################
################################################################################
############################################################
ELF image verification PASSED
Self extracting the image... [OK]
Self decompressing the image : #################################################
################################################################################
################################################################################
################################################################################
##################################################### [OK]
Restricted Rights Legend
Use, duplication, or disclosure by the Government is
subject to restrictions as set forth in subparagraph
(c) of the Commercial Computer Software - Restricted

Rights clause at FAR sec. 52.227-19 and subparagraph


(c) (1) (ii) of the Rights in Technical Data and Computer
Software clause at DFARS sec. 252.227-7013.
cisco Systems, Inc.
170 West Tasman Drive
San Jose, California 95134-1706

Cisco IOS Software, c6880x Software (c6880x-IPSERVICESK9-M), Version 15.1(2)SY3,


RELEASE SOFTWARE (fc4)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2014 by Cisco Systems, Inc.
Compiled Wed 11-Jun-14 13:48 by prod_rel_team
Image text-base: 0x00400170, data-base: 0x05573C60

Starting EOBC Switch Initialization


EOBC Switch Initialization is done!
System detected Virtual Switch configuration...
Interface TenGigabitEthernet 1/1/1 is member of PortChannel 10
Interface TenGigabitEthernet 1/5/1 is member of PortChannel 10
Initializing as Virtual Switch ACTIVE processor
This product contains cryptographic features and is subject to United
States and local country laws governing import, export, transfer and
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return this product immediately.
A summary of U.S. laws governing Cisco cryptographic products may be found at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html
If you require further assistance please contact us by sending email to
export@cisco.com.
USB high speed device - Port:0
Cisco C6880-X-LE ( Intel(R) Core(TM) i3- CPU @ 2.00GHz ) processor (revision ) w
ith 1833984K/262144K bytes of memory.
Processor board ID SAL184229BQ
Processor signature 0xA7060200
Last reset from s/w reset
1 Virtual Ethernet interface
1 Gigabit Ethernet interface
32 Ten Gigabit Ethernet interfaces
1966064K bytes of USB Flash bootdisk (Read/Write)

Press RETURN to get started!

Firmware compiled 29-Apr-14 09:31 by Build [0]

*Dec 2 19:23:30.367: %PFREDUN-6-ACTIVE: Initializing as ACTIVE processor for th


is switch
*Dec
ought
*Dec
P
*Dec

2 19:23:35.651: %VSL_BRINGUP-6-MODULE_UP: VSL module in slot 5 switch 1 br


up
2 19:24:08.063: %VSLP-5-RRP_ROLE_RESOLVED: Role resolved as ACTIVE by VSL
2 19:24:08.063: %VSL-5-VSL_CNTRL_LINK: New VSL Control Link 1/5/1

*Dec 2 19:24:08.115: %VSLP-5-VSL_UP: Ready for control traffic


*Dec 2 19:24:13.799: %VSL_BRINGUP-SW1-6-MODULE_UP: VSL module in slot 1 switch
1 brought up
*Dec 2 19:24:50.183: %USBFLASH-SW1-5-CHANGE: bootdisk has been inserted!
*Dec 2 19:25:09.795: %SW_VLAN-SW1-6-VTP_DOMAIN_NAME_CHG: VTP domain name change
d to ieso.
*Dec 2 19:25:18.779: %SYS-SW1-5-CONFIG_I: Configured from memory by console
*Dec 2 19:25:18.863: %SYS-SW1-5-RESTART: System restarted -Cisco IOS Software, c6880x Software (c6880x-IPSERVICESK9-M), Version 15.1(2)SY3,
RELEASE SOFTWARE (fc4)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2014 by Cisco Systems, Inc.
Compiled Wed 11-Jun-14 13:48 by prod_rel_team
*Dec 2 19:25:19.819: %OIR-SW1-6-INSPS: Power supply inserted in slot 1
*Dec 2 19:25:19.823: %C6KPWR-SW1-4-PSOK: power supply 1 turned on.
Firmware compiled 29-Apr-14 09:30 by integ Build [25600]

00:00:17.171 FW[MOD 17]: connor_b_led_init(): Error connor_hwrev_px: 0


Jan 1 00:01:13.879: DFC1: Currently running ROMMON from S (Gold) region
Jan 1 00:01:24.575: %SYS-DFC1-5-RESTART: System restarted -Cisco IOS Software, c7lc Software (c7lc-SP-M), Version 15.1(2)SY3, RELEASE SOFTW
ARE (fc4)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2014 by Cisco Systems, Inc.
Compiled Wed 11-Jun-14 13:16 by prod_rel_team
*Dec 2 19:25:20.679: %OIR-SW1-6-INSPS: Power supply inserted in slot 2
*Dec 2 19:25:20.779: %VS_MERGE-SW1-6-STDBY_CFG_MERGE: Merging standby VSL confi
guration

*Dec 2 19:25:20.799: %PFREDUN-SW1-6-ACTIVE: Standby initializing for SSO mode


*Dec 2 19:25:22.555: %OIR-SW1-6-INSFAN: Fan 1 inserted
*Dec 2 19:25:22.567: %OIR-SW1-6-INSREM: Switch 1 Physical Slot 5 - Module Type
LINE_CARD inserted
*Dec 2 19:25:52.559: %FABRIC-SW1-5-FABRIC_MODULE_ACTIVE: The Switch Fabric Modu
le in slot 5 became active.
*Dec 2 19:25:56.803: %OIR-SW1-6-INSREM: Switch 1 Physical Slot 1 - Module Type
LINE_CARD inserted
Jan 1 00:02:02.295: DFC1: Switch mode info received by DFC..!
*Dec 2 19:26:02.603: %DIAG-SW1-6-RUN_MINIMUM: Switch 1 Module 5: Running Minima
l Diagnostics...
*Dec 2 19:26:02.619: %CONST_DIAG-SW1-6-DIAG_PORT_SKIPPED: Module 5 port 1 is sk
ipped in TestLoopback due to: the port is used as a VSL link.
*Dec 2 19:26:08.511: %CONST_DIAG-SW1-6-DIAG_PORT_SKIPPED: Module 5 port 1 is sk
ipped in TestFexModeLoopback due to: the port is used as a VSL link.
*Dec 2 19:26:13.975: %CONST_DIAG-SW1-6-DIAG_PORT_SKIPPED: Module 5 port 1 is sk
ipped in TestL2CTSLoopback due to: the port is used as a VSL link.
*Dec 2 19:26:18.703: %OIR-SW1-6-INSREM: Switch 2 Physical Slot 5 - Module Type
LINE_CARD inserted
*Dec 2 19:26:20.199: %CONST_DIAG-SW1-6-DIAG_PORT_SKIPPED: Module 5 port 1 is sk
ipped in TestL3CTSLoopback due to: the port is used as a VSL link.
*Dec 2 19:26:30.395: %CONST_DIAG-SW1-6-DIAG_PORT_SKIPPED: Module 5 port 1 is sk
ipped in TestProtocolMatchChannel due to: the port is used as a VSL link.
*Dec 2 19:26:35.763: %DIAG-SW1-6-DIAG_OK: Switch 1 Module 5: Passed Online Diag
nostics
*Dec 2 19:26:42.175: %C6KENV-SW1-4-LOWER_SLOT_EMPTY: The lower adjacent slot of
module 5 might be empty. Airdam must be installed in that slot to be NEBS compl
iant
*Dec 2 19:26:48.935: %OIR-SW1-6-SP_INSCARD: Card inserted in Switch_number = 1,
physical slot 5, interfaces are now online
*Dec 2 19:27:02.359: %DIAG-SW1-6-RUN_MINIMUM: Switch 1 Module 1: Running Minima
l Diagnostics...
Jan 1 00:03:07.855: %CONST_DIAG-SW1_DFC1-6-DIAG_PORT_SKIPPED: Module 1 port 1 i
s skipped in TestLoopback due to: the port is used as a VSL link.
Jan 1 00:03:13.131: %CONST_DIAG-SW1_DFC1-6-DIAG_PORT_SKIPPED: Module 1 port 1 i
s skipped in TestFexModeLoopback due to: the port is used as a VSL link.
*Dec 2 19:27:11.011: %DIAG-SW1-6-RUN_MINIMUM: Switch 2 Module 5: Running Minima
l Diagnostics...
Jan 1 00:03:17.191: %CONST_DIAG-SW1_DFC1-6-DIAG_PORT_SKIPPED: Module 1 port 1 i
s skipped in TestL2CTSLoopback due to: the port is used as a VSL link.
Jan 1 00:03:22.035: %CONST_DIAG-SW1_DFC1-6-DIAG_PORT_SKIPPED: Module 1 port 1 i
s skipped in TestL3CTSLoopback due to: the port is used as a VSL link.
*Dec 2 19:27:30.395: %DIAG-SW1-6-DIAG_OK: Switch 1 Module 1: Passed Online Diag
nostics
*Dec 2 19:27:30.655: %C6KENV-SW1-4-HIGHER_SLOT_EMPTY: The higher adjacent slot
of module 1 might be empty. Airdam must be installed in that slot to be NEBS com
pliant
*Dec 2 19:27:30.907: %OIR-SW1-6-SP_INSCARD: Card inserted in Switch_number = 1,
physical slot 1, interfaces are now online
*Dec 2 19:27:44.079: %DIAG-SW1-6-DIAG_OK: Switch 2 Module 5: Passed Online Diag
nostics
*Dec 2 19:27:44.851: %OIR-SW1-6-SP_INSCARD: Card inserted in Switch_number = 2,
physical slot 5, interfaces are now online
*Dec 2 19:27:45.595: %VSLP-SW1-5-VSL_UP: Ready for data traffic
*Dec
*Dec
*Dec
*Dec
*Dec

2
2
2
2
2

19:25:58.099:
19:26:15.847:
19:26:15.951:
19:26:16.795:
19:26:48.699:

%USBFLASH-SW2_STBY-5-CHANGE: bootdisk has been inserted!


%OIR-SW2_STBY-6-INSPS: Power supply inserted in slot 1
%C6KPWR-SW2_STBY-4-PSOK: power supply 1 turned on.
%OIR-SW2_STBY-6-INSPS: Power supply inserted in slot 2
%FABRIC-SW2_STBY-5-FABRIC_MODULE_ACTIVE: The Switch Fabric

Module in slot 5 became active.


*Dec 2 19:27:11.011: %DIAG-SW2_STBY-6-RUN_MINIMUM: Switch 2 Module 5: Running M
inimal Diagnostics...
*Dec 2 19:27:11.011: %CONST_DIAG-SW2_STBY-6-DIAG_PORT_SKIPPED: Module 5 port 1
is skipped in TestLoopback due to: the port is used as a VSL link.
*Dec 2 19:27:16.875: %CONST_DIAG-SW2_STBY-6-DIAG_PORT_SKIPPED: Module 5 port 1
is skipped in TestFexModeLoopback due to: the port is used as a VSL link.
*Dec 2 19:27:22.339: %CONST_DIAG-SW2_STBY-6-DIAG_PORT_SKIPPED: Module 5 port 1
is skipped in TestL2CTSLoopback due to: the port is used as a VSL link.
*Dec 2 19:27:28.563: %CONST_DIAG-SW2_STBY-6-DIAG_PORT_SKIPPED: Module 5 port 1
is skipped in TestL3CTSLoopback due to: the port is used as a VSL link.
Cisco IOS Software, c6880x Software (c6880x-IPSERVICESK9-M), Version 15.1(2)SY3,
RELEASE SOFTWARE (fc4)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2014 by Cisco Systems, Inc.
Compiled Wed 11-Jun-14 13:48 by prod_rel_team
*Dec 2 19:28:11.655: %SYS-SW2_STBY-3-LOGGER_FLUSHED: System was paused for 00:0
2:49 to ensure console debugging output.
*Dec 2 19:28:13.203: %C6KENV-SW2_STBY-4-LOWER_SLOT_EMPTY: The lower adjacent sl
ot of module 5 might be empty. Airdam must be installed in that slot to be NEBS
compliant
Firmware compiled 29-Apr-14 09:30 by integ Build [25600]

00:00:17.147 FW[MOD 33]: connor_b_led_init(): Error connor_hwrev_px: 0


Jan 1 00:03:22.551: DFC1: Currently running ROMMON from S (Gold) region
Jan 1 00:03:28.015: %SYS-DFC1-5-RESTART: System restarted -Building configuration...
[OK]
Cisco IOS Software, c7lc Software (c7lc-SP-M), Version 15.1(2)SY3, RELEASE SOFTW
ARE (fc4)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2014 by Cisco Systems, Inc.
Compiled Wed 11-Jun-14 13:16 by prod_rel_team
*Dec 2 19:28:21.051: %VS_GENERIC-SW1-6-VS_HA_HOT_STANDBY_NOTIFY: Standby switch
is in Hot Standby mode
*Dec 2 19:28:21.051: %HA_CONFIG_SYNC-SW1-6-BULK_CFGSYNC_SUCCEED: Bulk Sync succ
eeded
*Dec 2 19:28:21.059: %VS_MERGE-SW1-6-SAVE_MERGED_CFG: Saving merged configurati
on...
*Dec 2 19:28:21.071: %RF-SW1-5-RF_TERMINAL_STATE: Terminal state reached for (S
SO)
*Dec 2 19:28:21.047: %PFREDUN-SW2_STBY-6-STANDBY: Ready for SSO mode in Default
Domain
*Dec 2 19:28:23.319: %OIR-SW1-6-INSREM: Switch 2 Physical Slot 1 - Module Type
LINE_CARD inserted
Jan 1 00:03:32.571: DFC1: Switch mode info received by DFC..!
*Dec 2 19:28:43.895: %DIAG-SW1-6-RUN_MINIMUM: Switch 2 Module 1: Running Minima
l Diagnostics...
*Dec 2 19:28:43.895: %DIAG-SW2_STBY-6-RUN_MINIMUM: Switch 2 Module 1: Running M
inimal Diagnostics...

*Dec 2 19:28:44.895: %SYS-SW2_STBY-3-LOGGER_FLUSHED: System was paused for 00:0


0:23 to ensure console debugging output.
Jan 1 00:03:55.939: %CONST_DIAG-SW2_DFC1-6-DIAG_PORT_SKIPPED: Module 1 port 1 i
s skipped in TestLoopback due to: the port is used as a VSL link.
Jan 1 00:04:00.455: %CONST_DIAG-SW2_DFC1-6-DIAG_PORT_SKIPPED: Module 1 port 1 i
s skipped in TestFexModeLoopback due to: the port is used as a VSL link.
Jan 1 00:04:04.543: %CONST_DIAG-SW2_DFC1-6-DIAG_PORT_SKIPPED: Module 1 port 1 i
s skipped in TestL2CTSLoopback due to: the port is used as a VSL link.
Jan 1 00:04:09.519: %CONST_DIAG-SW2_DFC1-6-DIAG_PORT_SKIPPED: Module 1 port 1 i
s skipped in TestL3CTSLoopback due to: the port is used as a VSL link.
*Dec 2 19:29:14.171: %DIAG-SW1-6-DIAG_OK: Switch 2 Module 1: Passed Online Diag
nostics
*Dec 2 19:29:15.027: %OIR-SW1-6-SP_INSCARD: Card inserted in Switch_number = 2,
physical slot 1, interfaces are now online
*Dec 2 19:29:14.147: %DIAG-SW2_STBY-6-DIAG_OK: Switch 2 Module 1: Passed Online
Diagnostics
*Dec 2 19:29:15.067: %C6KENV-SW2_STBY-4-HIGHER_SLOT_EMPTY: The higher adjacent
slot of module 1 might be empty. Airdam must be installed in that slot to be NEB
S compliant
*Dec 2 19:31:01.195: %VSLP-SW1-3-VSLP_LMP_FAIL_REASON: Te1/1/1: Link down
*Dec 2 19:31:01.315: %VSLP-SW2_STBY-3-VSLP_LMP_FAIL_REASON: Te2/1/1: Module off
line (removed, powered down or reset)
*Dec 2 19:31:01.351: %OIR-SW1-6-INSREM: Switch 2 Physical Slot 1 - Module Type
LINE_CARD removed
*Dec 2 19:31:01.323: %OIR-SW2_STBY-6-SP_REMCARD: Card removed from slot 1, inte
rfaces disabled
*Dec 2 19:31:11.007: %OIR-SW1-6-INSREM: Switch 2 Physical Slot 1 - Module Type
LINE_CARD inserted
Firmware compiled 29-Apr-14 09:30 by integ Build [25600]

Вам также может понравиться