Академический Документы
Профессиональный Документы
Культура Документы
Vacuum cleaner
FC8421
/02
/A
Service Manual
PRODUCT INFORMATION
- First lift and remove the knob and printed knob base and
then loosen mounting screws A.
Colour: Anthracite
Electronically controlled motor speed
Built-in cord winder
Dustbag-full indicator in dust cover
This product meets the requirements regarding
interference suppression on radio and TV.
- After the product has been repaired, it should function
properly and has to meet the safety requirements as
officially laid down at this moment.
TECHNICAL INFORMATION
-
: 34 l/sec.
: 260 cm
: 1500 W
: 2l
: 6m
: 5 filters
: 382 x 292 x 218 mm
: 510 x 305 x 330 mm
: 4.5 Kg
: 8,0 Kg
: 79 dB
- Lift the motor housing (item 26) out of the lower housing
and take out the cord winder unit.
- To disassemble the cord winder, use TORX screwdriver no.
T10, which is one of a set consisting of T20; T15; T10;
T9; T8; T7 and T6 (code number 4822 395 50145).
OPTIONAL (accessories)
- FC8021 S-paper dustbags
- FC8032 Exhaust AFS micro filter
- HR6997 Sydney cotton dustbag
03/06
Copyright reserved
Subject to modification
FC8421/02/A
REPAIR INSTRUCTION
- The spare parts have been standardized as much as possible.
- Cotton dustbags are used in countries where paper dustbags
are unobtainable.
- If the reel half spring unit is replaced, shaft F must be
lubricated with silicone grease. Do not apply any silicone
grease to or spill any grease on terminals (36) or conductors
(35).
- Item 34 is provided with a long cord-winder spring, but
both long and short cords can be used in combination with
this spring. (L = 9.3 m)
- Depending on the length of the original cord, the spare
cord may have to be shortened.
- The cord winder spring must be tensioned to the maximum
level and then be rewound approx. 1.5 turn.
- The RPM can be adjusted by means of the potentiometer
mounted on the PCB (item 25). The RPM is correctly
adjusted if the motor starts automatically and continues to
run smoothly with the ON/OFF position and the
adjustable potentiometer in minimum position.
- If the function of the electronic control unit (item 25) is
not required, the Triac must be short-circuited in the
manner shown in the circuit diagram.
- When the vacuum cleaner is used to suck up fine dust, the
pores of the dustbag may become clogged, causing the
passage of air through the dustbag to become obstructed.
As a result, the dustbag-full indicator will indicate that the
dustbag needs to be replaced, even though the dustbag is
not full at all.
ELECTRICAL DIAGRAM
CORD WINDER
Brown
Triac
Blue
MOTOR
POWER
MODULE
Black
Black
M
Short-circuit
2-6
PARTS LIST
FC8421/02/A
Pos
Service code
1
2
3
4
handle
dust cover
S-bag set
cotton dustbag
dustbag frame
5
6
7
8
9
32
33
34
10
11
12
13
14
wheel bush
safety filter
caster assy
cover and filter
turn knob grip stand
36
37
15
16
17
18
19
20
21
22
23
24
25
26
27
Description
Pos
Service code
28
brake tyre
base plate assy
reel half spring unit
reel half spring unit PRC
reel half contact side
38
39
knob base
cord outlet
upper housing
pedal
AFS back grille
40
41
42
46
47
AFS filter
wheel peg
cooling tube
switch lever
switch soldered
48
49
50
51
52
accessory clip
crevice nozzle con.
small nozzle con.
dusting brush con.
big nozzle con.
53
54
55
Anthracite
Anthracite
(opt.)
29
30
31
35
Description
(opt.)
(opt.)
3-6
EXPLODED VIEW
FC8421/02/A
14
15
A
16
2
A
17
B
A
B
11
18
10
19
20
5
6
7
C
8
9
C
13
12
21
D
D
4-6
EXPLODED VIEW
FC8421/02/A
23
25
24
E
E
26
E
22
27
28
29
31
33
30
32
35
34
3740
G
36
5-6
EXPLODED VIEW
FC8421/02/A
Taiwan / P.R.C.
37
Korea / Europe
39
H.K. / U.K.
38
Swiss
40
41
42
49
46
48
47
50
51
54
53
52
55
6-6