Академический Документы
Профессиональный Документы
Культура Документы
G-Series
Pneumatic & Hydraulic
Actuators
Five-Year Warranty
Severe Service Rated
Tension-Lok
Powr-Swivl
Acculine Shaft Drive
True Modular Design
Wear and Corrosion Resistant
Environmentally Sealed
Safety
NAMUR
Type Approved
ISO 9001
Versatile
Product Concept
In developing the G-Series
actuators, Bettis improved a
basic concept the Reaction
Bar, by adding our new state-ofthe-art Powr-Swivl, replaceable
bearings, highly efficient wear
and corrosion resistant coating
system, and tension rod compressed spring. This enhanced
design greatly improves efficiency, reduces wear and
extends the actuators life. The
combining of these technologies,
enhancements, and superior
quality control techniques produced an assembly which
became the heart of our new
extended service actuators
the G-Series.
Advantages
The G-Series actuators provide
a unique, highly reliable means
of operating ball, butterfly, or
plug valves, as well as louvers,
dampers and other 90 degree
rotating mechanisms.
Manual Hydraulic
Pump System
Pneumatic
Power
Module
Tandem
Pneumatic
Power Module
Pneumatic Power
Module with
Extended
Travel Stop
Drive
Module
Hydraulic
Power Module
environmental conditions.
Proper actuator selection,
enhanced by proprietary data
analysis methods, allows optimum performance and operating economy.
Replaceable Bearings Low
friction, permanently lubricated, high performance bearings protect sliding and
rotating components, significantly extending actuator life.
Five Year Warranty G-Series
actuators are backed by the
industrys strongest materials
and workmanship warranty.
Corrosion Resistance
G-Series actuators incorporate
protective internal and external
coatings, assuring the actuators reliable operation in the
harshest of environments. The
actuator exhibits excellent corrosion resistance, confirmed
by Salt Spray Testing per
ASTM B117 criteria. Construc
3 Acculine
14 Pressure Port
Shaft Drive
11 Breather
ACTUATOR
HOUSING
15
7 Yoke Pin
Thrust Bar
2 Power-Swivl
NAMUR
13 Vent-Checks
HOUSING
VENT/CHECK
VALVE
VENT/CHECK
YOKE
Replaceable Bearings
Tension-Lok
10 Lifting Eyes
LOCKED
UN-LOCKED
9
6 Guide Block
Thrust Bushing
Spring
Module
REACTION BAR
Optional Internal
Hydraulic Override
GUIDE BLOCK
14
uae
POWR - SWIVL(S)
Pressure Port. The inboard pressure port location minimizes exposure of supply tubing, thus
reducing the opportunity for
mechanical damage on springreturn units. Pneumatic units feature NPT ports while hydraulic
units have SAE ports. Consult
factory for options.
100
90
80
5
+5
Typical Specifications
The following information is recommended as a guide to develop a
comprehensive, performance oriented pneumatic and hydraulic
actuator and control specification.
Bettis G-Series actuators meet or
exceed all requirements outlined
below.
Purpose
To define a pneumatically or
hydraulically powered actuator
suitable for the operation of ball,
butterfly, or plug valves, louvers,
dampers, and other 90 rotating
mechanisms.
1. The actuator shall be competitively priced, reliable,
scheduled maintenance
free, fully resistant to environmental, power gas, and
load conditions.
2. The actuator shall be
designed to facilitate ease of
installation and serviceability.
The actuator shall incorporate
a true modular design to simplify field service, interchangeability of the power
and spring modules, and the
addition of manual overrides
and accessories. Each primary actuator module shall
be permanently identified
and documented to allow
accurate identification of
components and application
criteria.
3. The actuator shall meet all
applicable design codes,
safety restrictions, and application practices including
SI 1029 regulations and
IP 67M type testing.
4. The power and spring modules shall be rigidly attached
by external bolting to the
drive module and accurately
aligned by a piloted interface.
The attachment shall not
require special tools, disassembly, or disturbance of
seals of any module.
6
orientations, as specified.
13. The actuator shall be service
rated based upon load and
application parameters,
auditable to accelerated
wearage test data.
14. Integral lifting eyes shall be
provided to facilitate safe
shipping, handling, installation, and removal of the actuator. Eight lifting eyes,
suitable for safely lifting the
actuator in all three major
planes, shall be sufficiently
sized and located to accept
appropriately rated lifting
devices.
15. All external bolting shall be
installed in blind tapped
holes to protect the threads
and positively prevent water
ingress as defined by the
requirements of IP 66 and
IP 67M. Sheet or fibrous gaskets shall not be used for
pressure or environmental
seals.
16. The NAMUR mounting configuration shall be incorporated for the attachment of all
shaft driven accessories. The
attachment configuration
shall be identical for all actuator models and shall provide visual position
indication.
17. Accessory drive shaft shall
be bearing centered, with
respect to the mounting
pattern and isolated from
any axial or radial yoke
movements.
18. All shaft driven control and
signal devices shall be protected from mechanical damage by a bearing centered
shaft drive meeting NAMUR
dimensional specifications.
Device attachment shall be
identical and interchangeable between all models.
19. The spring preload shall apply
a compression force to positively retain the spring and
34.
35.
36.
37.
38.
Headquarters
P.O. Box 508
Waller, TX 77484
U.S.A.
Tel: 281/463-5100
Fax: 281/463-5103
E-mail:
marketing.bettis@bettis.com
Website: www.bettis.com
Optional Overrides
Bettis offers several overrides for G-Series model, they include:
Jackscrew manual override for G-1, G-2, and G3 models
with or without handwheel.
G-Ride gear override available on G-4 and G-5 models.
All overrides have a variety of options available including
proximity switches and lock out features
Bettis UK Ltd.
Brunel Way
Fareham, Hampshire PO15 5SA
England
Tel: 0148-988-5333
Fax: 0148-988-5200
Tlx: 47493
Bettisystems
Bettis has pre-engineered and documented a series of
commonly required control systems. These approved systems
utilize standard components, reduce lead times, and simplify
purchasing, installation and start-up. Please consult the factory
for additional information.
Bettis France:
30/36 Allee du Plateau
93250 Villemomble
France
Tel: 331-48-122610
Fax: 331-48-122619