Академический Документы
Профессиональный Документы
Культура Документы
ITEM DESCRIPTION
AMOUNT
TOTAL AMOUNT
BOQ - Summary
Page 1
0.00
Sl. No.
1.00
1.01
Cum
50.00
1.02
Cum
25.00
1.03
Cum
75.00
Cum
170.00
Cum
37.00
Smt
256.00
2.00
Providing and constructing 200mm thick Non load bearing wall with
precast concrete solid blocks of size 40x20x20cms with compressive
strength Not less than 38 Kg/sqm with cement mortar 1:6 masonry of joint
thickness Not to be more than 20mm (quoin, jamb, closer blocks )
confirming to I.S. 2185/1965 in superstructure including cost of materials,
labour charges, scaffolding, ladders, platforms, staging, curing, plant
required for the execution of the work etc.. Complete as per specifications
& relevant drawings / as directed by the Architect / Engineer In charge.
Bearing blocks of concrete or bricks in motor courses will have to be
introduced where ever required.
3.00
PLASTERING
Providing 12mm thick average cement plastering for RCC, Masonry
work, under sides of slab etc., Complete to true line and plane in all levels
and locations using CM 1:6 as per specifications including necessary
scaffolding, curing etc., as per instruction of the Architects.
4.00
5.00
6.00
PCC 1:4:8 for all RCC and boundary wall works and below flooring,
drains, trenches, pits, UGT etc wherever required
R C C M25 grade concrete with necessary plasticizer and water proof
compound for tanks
Reinforcement steel
Cum
18
Cum
53
Mt
6.5
7.00
Shuttering for all RCC works with ply sheets and necessary MS
Scaffolding with verticals of cup locks / H frames and tie rods wherever
required and stays as required etc complete.
Smt
360
8.00
Smt
105
9.00
Cum
25
10.00
FLOORING
Note:
The interior contractor has to check the existing floor for perfect leveling
before laying the Granite / vitrified tiles. If any undulations are found in
the floor shall be bring to the Notice of the project manager in writing and
get the approval for making up of level. If the contractor used any
material to make up the floor to level without Notice, No payment will be
made towards the same. Small local undulations (Up to +/- 10mm) shall
be leveled by the contractor which shall be included in the quoted rate and
No extra payment will be made for the same. If any corrections were
made as per approval from project manager, the contractor has to maintain
the joint measurement record (JMR) and to be produced at the time of
claim from the main general contractor.
Basic rate of any material shall mean the cost of material including
all applicable taxes, transportation charges to work site, loading,
unloading and stacking of material at required location and different
levels.
10.01
Smt
34.00
Smt
4.50
Smt
13.00
11.00
12.00
GRANITE FLOORING
13.00
Smt
1.00
Smt
17.00
RMT
17.00
Providing and fixing of ceramic tile dado using approved size of 200mm x
200mm approved make and color from floor level up to 2400mm height
set in CM 1:4 10mm thick cement backing. Tile to be layed in pattern as
indicated in the detail drawing. Aluminium "C" channel to be flushed
inline with dado at 2400mm Level to get groove same needs to be
included in the cost. Quoted rate to include the cost of making cut-outs
for electrical outlet and cost of filling the joints in dado with (BAL - RG1
Hygienic Impervious tile grout) curing etc., All the corner tiles to have
PVC edge beading of approved color and make as per detail drawing and
same to be considered in the quoted rate. Consider basic rate of tile at Rs.
450/-Smt. Including all taxes and transport.
14.02
15.00
PARTITIONS WALLS
Note:
Unless otherwise specified, the quoted rate of all blocked partitions shall
include the cost of two coats of gypboard primer, putty and two coats of
Acrylic emulsion paint of approved quality on both sides of partition.
Before painting the walls / partitions, the contractor has to take written
approval from architects.
15.01
Smt
7.00
Smt
90.00
Cladding:
NoTE :
16.01
PAINTING WORKS
Contractor shall protect the entire furniture provided by him or other
agencies before starting the painting / punning work and shall be held
responsible for any stains or damage including aluminium windows, AC
grilles, Diffusers, grid ceiling, Modular furniture, carpet etc.,
Providing and applying soft sheen enamel paint finish to walls, blocked
partitions, and plasterboard ceiling surfaces of approved shade, texture.
As per specification below.
POP PUNNING
Smt
90.00
Smt
90.00
No
1.00
TEXTURE PAINTING
Providing necessary Texture paint 5mm thickness of approved make &
Color as per the requirement of the client. The rates inclusive of pressure
cleaning, ICI / Asian Primer, Birla Texture & two top coats of external
emulsion of Apex as per the standard specification and as direction of the
Architect.
19.00
a)
b)
c)
Shutter:
Shutters: 32mm thick solid core flush door shutter finished with
approved 1mm thk laminate on both faces of the shutter. Shutter edges to
be lipped with 32mm x 6mm beech wood beading all around finished in
melamine polish. Refer Door Detail drawings.
d)
Hardware:
Hinges: 3 No's SS Ball bearing hinges (Dorset or approved equivalent
make)
Handle: Brushed SS 'C' type Handle (Dorset or approved equivalent
make)
Lock: Indicator Bolt (Dorset or approved equivalent make)
Door closer: NA
The door frame should be fixed to the partition with 8mm flat head wood
screws from behind or the frame is fixed to the masonry wall using M.S
hold fast with clear anti termite treatment for the concealed partition of
the frame.
20.00
GLAZING
20.01
Semi Unitized Glazing Providing and fixing semi unitized single glazed
6mm structural glazing system having main frame work of verticals and
horizontal made out of specially design extruded polyester powder coated
aluminum section to withstand wind speed of 150 Km/hr. 6mm glass
KT155 Saint Gobain Glass NaNo Moonshine of approved make online
coated glass with all standard necessary accessories connector joinery
which shall be HILTI/Fischer chemically grouted, including fixing of
aluminium sub frames, silicon sealant Dow Corning, EPDM triple
barriers, weather strip to ensure water and air-tightness etc. complete as
detailed in shop drawings and as directed by Architects. The wind load as
per I.S. 1.5 Kpa. The rate inclusive of G.I flashing & Smoke seal. The
structural calculation & wind load report should be submitted along with
Dow corning warranty of 10years.
Smt
58.00
20.02
No
1.00
20.03
Smt
8.00
Note:- All cladding tiles should be full tile & cut tiles are Not allowed.
21.00
TOTAL AMOUNT:-
Smt
1.10
RPOSE
CK
PUR.
RATE
AMOUNT
1.00
50.00
-
50.00
UNIT
QTY
Cum
265
2.00
Solid block masonry 230/100 mm thick for panel walls in superstructure with
CM (1:6) prop. ( cement : sand ) using second class bricks from approved source
having crushing strength not less than 50 Kg / Sqcm. including cost and
conveyance of all materials like cement, sand, bricks, water etc., to site, including
seignior age charges, sales & other taxes on all materials and all operational,
incidental and Labour charges such as mixing cement mortar, scaffolding charges,
constructing masonry, lift charges, curing, etc., complete for finished item of work.
Cum
75
3.00
Providing M20 concrete for the coping as per including necessary shuttering.
Cum
10
4.00
Kg
750
5.00
PLASTERING
Sqm
500.00
Providing necessary Texture paint 5mm thickness of approved make & Color as
per the requirement of the client. The rates inclusive of pressure cleaning, ICI /
Asian Primer, Birla Texture & two top coats of external emulsion of Apex as per
the standard specification and as direction of the Architect.
Sqm
500.00
Smt
250
1.00
DESCRIPTION
Providing and constructing CR masonry in CM 1:6, 300 - 750 tk. Using hammer
dressed bond stones at every 2 meters, including hammer dressed stoned face for
elevation walls including raking ,scaffolding etc. complete. Rates inclusive of
removing existing loose masonry and soil as per the engineer instruction.
6.00
7.00
PAINTING
TOTAL AMOUNT
RPOSE
ALL
PUR.
RATE
AMOUNT
0
0
0.00
1.01
DESCRIPTION
2.00
2.01
3.00
40.00
Cum.
20.00
Cum.
60.00
Cum.
60.00
Cum.
20.00
Earth work excavation for Foundations, depositing on bank with an initial lead of
10m and lift of 2m in all types hard rock required blasting including shoring
shuttering, sheeting, planking and dewatering including cost of hire charges of T&P,
Back filling in layers not exceeding 150mm thick and compacted with earth rammer
(after footing work completed) all labour charges and etc., complete for finished item
of work, as directed by the Engineer-in-charge.( for Foundations)
Filling in trenches and basement with excavated earth, boulders are to be broken
rolled and well consolidated in layers not exceeding 20mm thick each layer
sufficiently watered and throughly compacted.
Basement
1.04
Cum.
Earth work excavation for Foundations, depositing on bank with an initial lead of
10m and lift of 2m in all types of soils including soft rock like murrum soils, red
earth and ordinary gravely soils mixture of gravel and S.D.R. like shale's, ordinary
gravel stony earth and earth mixed with fair sized boulders except rock required
blasting including shoring shuttering, sheeting, planking and dewatering including
cost of hire charges of T&P, Back filling in layers not exceeding 150mm thick and
compacted with earth rammer (after footing work completed) all labour charges and
etc., complete for finished item of work, as directed by the Engineer-in-charge.( for
Foundations)
For Footing
1.03
QTY
1.02
UNIT
Filling in trenches and basement with brought out earth with well consolidated in
layers not exceeding 20mm thick each layer sufficiently watered and throughly
compacted.
Basement
PCC
Plain Cement Concrete ( 1:4:8) prop. corresponding to M 7.5 grade as per IS 456,
using 40mm and down graded machine crushed hard granite metal (coarse aggregate)
from approval quarry, river sand from approved quarry, with OPC of 53 grade from
approved manufacturer for foundation bed for footings including cost &
conveyance of all materials like cement, fine aggregate (river sand), course
aggregate, water etc., to site, including cost of seigniorage charges, taxes on all
materials, necessary shuttering, machine mixing, concrete laying, ramming in layers,
finishing top surface to the required level, curing and etc., complete, as directed by
the Engineer-in-charge for finished item of work.
Page 18 of 49
3.01
3.02
12.00
Cum.
3.00
Cum.
6.00
Cum.
14.00
3.03
Cum.
Page 19 of 49
5.01
6.01
Solid block work for panel walls in superstructure with CM (1:6) prop. ( cement :
sand ) using approved source having crushing strength not less than 50 Kg / Sqcm.
including cost and conveyance of all materials like cement, sand, bricks, water etc.,
to site, including seigniorage charges, sales & other taxes on all materials and all
operational, incidental and labour charges such as mixing cement mortar, scaffolding
charges, constructing masonry, lift charges, curing, etc., complete for finished item of
work.
Cum
34.00
Sqm
15.00
JOINERY WORK:
a) DOORS & Windows
Supply and fixing MS framed with GI mesh doors and windows as per the drawing
with necessary primer and painting, Rates inclusive of hold fast extra as per the
engineer instruction.
PLASTERING
Supply and laying plastering with cement mortar as specified to brick or concrete
surfaces and at all heights including chipping, faces and at all heights including
chipping, hacking, scaffolding, curing etc., complete with all materials and labour for
finished itemof work.
7.01
a) 16mm thick in Double coat in CM (1:6) & (1:4) trowelled to even and smooth
finish or as directed for ceiling & Internal walls.
Sqm
150.00
b) External Plastering
Ground Floor
FLOORING
Sqm
208.00
Providing and laying Polished kotta stone of approved shade with CM(1:5) laid over
the surface to required level and slope including the cost of cleaning the jointed
cement slurry mixed with color pigment.
Sqm
162.00
Sqm
208.00
Sqm
150.00
Sqm
Sqm
50.00
90.00
7.02
8.01
PAINTING
9
9.01
9.02
12
Supply, cleaning all surfaces of dirt, dust loose scales etc. before painting all
materials labour and scaffolding at all heights for a) Providing two coats of ACE
with primer.
a) Externalwalls
b)Providing and applying Plastic Emulsion Paint over 2 coats Lappam to internal
walls.
FORM WORKS
Providing, fabricating and erecting, form work at all levels and places wherever
needed/specified as per drawing including striking with 12mm Plastic coated, marine
resistant waterproof ply / M S steel plates(All Beam&lintel sides, bottom, drop
panels/ Capital sides should be of Marine ply wood) with adjustable steel props of
acceptable Staging system and with sufficient bracing as approved by consultant.
Cost to include designing of proper form work and staging system to suit the
requirements, sealing the joints with heavy duty brown self adhesive tape, aligning to
line and levels including M.S. Ties, PVC Spacer, Providing openings/ cut-outs/
pockets, applying de-shuttering chemical, De-shuttering as approved by the
consultant etc., complete at all floors / levels,(but height up to 4.00 mts. only)and
profiles for
Note :(1) Only plan area only considered for slabs up to 150 mm
thick slabs, for above 150 mm thick slabs skirting well be considered.
a) For Foundations
b) For Pedestal
Page 20 of 49
13
Sqm
110.00
Mt
1.20
Mt
5.62
No
66
Sqm
370
Providing High yield strength deformed steel bars (Fe 500 ) of different diameters,
cutting, bending to required sizes and shapes placing in position with cover blocks of
approved size, binding wire of 20 SWG, forming grills for reinforcement work as per
approved designs and drawings, including cost and conveyance of bars from
approved manufactures RINL, TISCON or equivalent, including cost and conveyance
of binding wire, cover blocks, overlaps, chair and all wastages, rusting (quantity for
overlaps, chairs, couplings, welded joints, spacer bars etc will not be measured
separately and are to be accounted in costing ) including drilling boreholes and
grouting the anchor bars wherever necessary and all taxes on all materials, all
incidental, operational, labour charges such as cutting, bending, placing in position,
tying etc., complete for finished item of work.
14
15
15
Page 21 of 49
AMOUNT
Page 22 of 49
Page 23 of 49
0
0
0
0
Page 24 of 49
0
0
0
0
Page 25 of 49
ITEM No.
1.00
1.01
1.02
2.00
2.01
3.00
Cum.
40.00
Cum.
120.00
Cum.
120.00
Cum.
40.00
1.04
80.00
1.03
Cum.
Filling in trenches and basement with brought out earth with well
consolidated in layers not exceeding 20mm thick each layer sufficiently
watered and throughly compacted.
Basement
PCC
3.01
3.02
24.00
Cum.
6.00
Cum.
12.00
Cum.
28.00
3.03
Cum.
4.00
5.00
5.01
6.01
Solid block work for panel walls in superstructure with CM (1:6) prop.
( cement : sand ) using approved source having crushing strength not less
than 50 Kg / Sqcm. including cost and conveyance of all materials like
cement, sand, bricks, water etc., to site, including seignior age charges, sales
& other taxes on all materials and all operational, incidental and labor
charges such as mixing cement mortar, scaffolding charges, constructing
masonry, lift charges, curing, etc., complete for finished item of work.
Cum
55.00
Sqm
40.00
JOINERY WORK:
a) DOORS & Windows
Supply and fixing MS framed with GI mesh doors and windows as per the
drawing with necessary primer and painting, Rates inclusive of hold fast
extra as per the engineer instruction.
PLASTERING
7.00
7.01
a) 16mm thick in Double coat in CM (1:6) & (1:4) trowelled to even and
smooth finish or as directed for ceiling & Internal walls.
Sqm
300.00
b) External Plastering
Ground Floor
FLOORING
Sqm
400.00
Providing and laying Polished kotta stone of approved shade with CM(1:5)
laid over the surface to required level and slope including the cost of
cleaning the jointed cement slurry mixed with color pigment.
Sqm
330.00
Sqm
300.00
Sqm
400.00
7.02
8.01
PAINTING
9.00
9.01
9.02
10.00
Supply, cleaning all surfaces of dirt, dust loose scales etc. before painting all
materials labor and scaffolding at all heights for a) Providing two coats of
ACE with primer.
a) External walls
b)Providing and applying Plastic Emulsion Paint over 2 coats Lappam to
internal walls.
FORM WORKS
Providing, fabricating and erecting, form work at all levels and places
wherever needed/specified as per drawing including striking with 12mm
Plastic coated, marine resistant waterproof ply / M S steel plates(All Beam &
lintel sides, bottom, drop panels/ Capital sides should be of Marine ply
wood) with adjustable steel props of acceptable Staging system and with
sufficient bracing as approved by consultant. Cost to include designing of
proper form work and staging system to suit the requirements, sealing the
joints with heavy duty brown self adhesive tape, aligning to line and levels
including M.S. Ties, PVC Spacer, Providing openings/ cut-outs/ pockets,
applying de-shuttering chemical, De-shuttering as approved by the consultant
etc., complete at all floors / levels,(but height up to 4.00 mts. only)and
profiles for
Note :(1) Only plan area only considered for slabs up to 150
mm thick slabs, for above 150 mm thick slabs skirting well be considered.
11.00
a) For Foundations
b) For Pedestal
c) For Plinth Beams & Column
REINFORCEMENT STEEL:
Sqm
Sqm
Sqm
100.00
180.00
400.00
Mt
2.40
Providing MS steel truss as per the design with necessary primer & painting
as per the engineers instruction.
Mt
9.80
No
90
Sqm
180
Providing High yield strength deformed steel bars (Fe 500 ) of different
diameters, cutting, bending to required sizes and shapes placing in position
with cover blocks of approved size, binding wire of 20 SWG, forming grills
for reinforcement work as per approved designs and drawings, including cost
and conveyance of bars from approved manufactures RINL, TISCON or
equivalent, including cost and conveyance of binding wire, cover blocks,
overlaps, chair and all wastages, rusting (quantity for overlaps, chairs,
couplings, welded joints, spacer bars etc will not be measured separately and
are to be accounted in costing ) including drilling boreholes and grouting the
anchor bars wherever necessary and all taxes on all materials, all incidental,
operational, labor charges such as cutting, bending, placing in position, tying
etc., complete for finished item of work.
12.00
13.00
BOLTS
14.00
Providing foundation bolts of 20mm dia with 600 depth as per the design
and engineers instruction.
Sheet
Providing and laying of GI powder coated sheet of 0.48mm thick as per
the required color and design.
TOTAL AMOUNT
RPOSE
AGE
PUR.
RATE
AMOUNT
0
0
0
0
0
0
0
ITEM No.
1.00
Providing and fixing in position two piece High polished natural stone slab
20mm. Thick, both edges machine cut, machine chamfered and polished as per
the drawing over a bed of 1:4 cement mortar to exact lines and levels including
filling the joints with M - Seal / Silicon sealants as directed to make it absolutely
water tight.
2.00
TREADS
Sqm
200.00
Sqm
120.00
Sqm
560.00
Rmt
100.00
Providing and fixing in position one piece treads of approved quality and co lour
High polish natural stone slab 20 to 25 mmthick front edge machine
cut,chamfered and polished as per the drawing over a bed of 1:4 cement mortar
including necessary dressing/ cutting, cement float, filling the joints with neat
cement slurry of appropriate color, watering, curing, cleaning etc. complete to
exact line, level and to the satisfaction of the Architect.
2.10
3.00
4.00
URPOSE
ASE FINISHING
LAPUR.
RATE
AMOUNT
ITEM No.
1.00
WATER PROOFING
1.01
100%
POLYISOPRENE-BASED
WATERPROOFING MEMBRANE WITH
INSULATION SYSTEM:
ELASTOMERIC
BRICK-BAT COBA Sqm
The fourth part consisting of providing and applying liquid-applied, singlecomponent, 100% Poly-isoprene (Polyurethane) based Elastomeric
Waterproof Membrane, having elongation of 550% (offered system :
ZUPA Equation 60, from M/s. Zenex Const. Chemicals Inc., USA), at
the coverage rate of 0.8 kg /sq.m. in 2 coats, as per manufacturers
specifications, over the entire roof terrace concrete slab and parapet walls
upto 300 mm height.
The fifth part consisting of providing and sprinkling of 8/12 grade quartz
pieces on the second coat of the wet membrane, to provide for protection of
the membrane as well as bonding of the subsequent screed, as per
manufacturers specifications approved by Consultants. Brushing off the
excess sand after the membrane has set.
650
The sixth part consisting of providing and laying rigid insulation and slope
making with avg. 115 mm thick brick-bat koba system comprising of 20
mm thick, CM 1:4 base coat, avg. 75 mm thick brick-bat coba in CM 1:5
mortar and 20 mm thick, CM 1:4 top-finish coat. The mortar for the brickbat koba shall be CM 1:4 and admixed with integral waterproofing
compound @ 100 ml/bag of cement, curing, complete. The top-finish coat
shall be suitably finished (either smooth IPS with 30 cm x 30 cm false
marked squares or broom-finished suitable for laying china mosaic tiles).
The cost should include treatment of cove (wata) at the interface of floor
and parapet, sealing the annular space between the pipe and the masonry,
making churros, river sand screened and washed, at all leads, lifts, heights,
scaffolding, with proper slope to drain-off water entirely, complete, etc.
Curing shall be done for 7 days by ponding with water.
The seventh part consisting of sealing all joints of outlet drain pipe and
making churros, etc. with ZUPA Repaira.
1.02
Plastering
Providing 20mm thick average cement plastering for RCC, Masonry work,
under sides of slab etc., Complete to true line and plane in all levels and
locations using CM 1:6 as per specifications including necessary
scaffolding, curing etc., as per instruction of the Architects.
Sqm
100
1.03
Providing and laying 150mm dia PVC pipe Ashirwad with necessary
assocceries. The rate inclusive dismantling and plastering etc. as per
instruction of the Architects.
Rmt
35
2.00
Cum
30
Sqm
100
Dismantling the existing solid block as per the requirement of our engineer,
Rate inclusive of all scaffolding, lead, Lift, etc. The dismental material
should be removed from the site upto 100mtr away.
a
Plastering
Providing 12mm thick average cement plastering for RCC, Masonry work,
under sides of slab etc., Complete to true line and plane in all levels and
locations using CM 1:6 as per specifications including necessary
scaffolding, curing etc., as per instruction of the Architects.
3.00
PHE
Providing and laying 50mm dia GI pipe 'B' class with necessary assocceries
to hook up the existing bore to U/G tank. The rate inclusive excavation,
bitumen wrapping etc. As per instruction of the Architects.
Rmt
200
Providing and laying 50mm dia GI valve zoloto boll valve to hook up the
existing bore to U/G tank. The rate inclusive excavation, bitumen wrapping
etc. As per instruction of the Architects.
No
TOTAL AMOUNT
URPOSE
OPINING & PHE
LAPUR.
RATE
AMOUNT
0
0
0
0
ITEM No.
1.00
FOUNDATION WORKS
1.01
For Footing
1.02
2.00
2.01
3.00
Cum.
10.00
Cum.
30.00
Cum.
40.00
Cum.
5.00
1.04
30.00
1.03
Cum.
Filling in trenches and basement with brought out earth with well
consolidated in layers not exceeding 20mm thick each layer sufficiently
watered and thoroughly compacted.
Basement
PCC
3.01
5.01
6.01
Cum.
70.00
Cum.
10.00
Cum.
18.00
Sqm
7.00
Solid block work for panel walls in superstructure with CM (1:6) prop.
( cement : sand ) using approved source having crushing strength not less
than 50 Kg / Sqcm. including cost and conveyance of all materials like
cement, sand, bricks, water etc., to site, including seignior age charges, sales
& other taxes on all materials and all operational, incidental and labor
charges such as mixing cement mortar, scaffolding charges, constructing
masonry, lift charges, curing, etc., complete for finished item of work.
JOINERY WORK:
a) DOORS & Windows
Supply and fixing MS framed with GI mesh doors and windows as per the
drawing with necessary primer and painting, Rates inclusive of hold fast
extra as per the engineer instruction.
PLASTERING
7.01
a) 16mm thick in Double coat in CM (1:6) & (1:4) trowelled to even and
smooth finish or as directed for ceiling & Internal walls.
Sqm
150.00
b) External Plastering
Ground Floor
FLOORING
Sqm
150.00
Providing and laying Polished kotta stone of approved shade with CM(1:5)
laid over the surface to required level and slope including the cost of
cleaning the jointed cement slurry mixed with color pigment.
Sqm
50.00
7.02
8.01
4135.00
Providing and laying Polished IPS flooring with CM(1:4) laid over the
surface to required level and slope including the cost of cleaning the jointed
cement slurry.
Sqm
100.00
Sqm
150.00
Sqm
150.00
Sqm
700.00
Mt
1.50
Mt
3.00
PAINTING
9
9.01
9.02
12
Supply, cleaning all surfaces of dirt, dust loose scales etc. before painting
all materials labor and scaffolding at all heights for a) Providing two coats
of ACE with primer.
a) External walls
b)Providing and applying Plastic Emulsion Paint over 2 coats Lappam to
internal walls.
FORM WORKS
Providing, fabricating and erecting, form work at all levels and places
wherever needed/specified as per drawing including striking with 12mm
Plastic coated, marine resistant waterproof ply / M S steel plates(All Beam
& lintel sides, bottom, drop panels/ Capital sides should be of Marine ply
wood) with adjustable steel props of acceptable Staging system and with
sufficient bracing as approved by consultant. Cost to include designing of
proper form work and staging system to suit the requirements, sealing the
joints with heavy duty brown self adhesive tape, aligning to line and levels
including M.S. Ties, PVC Spacer, Providing openings/ cut-outs/ pockets,
applying de-shuttering chemical, De-shuttering as approved by the
consultant etc., complete at all floors / levels,(but height up to 4.00 Mts.
only)and profiles for
Note :(1) Only plan area only considered for slabs
up to 150 mm thick slabs, for above 150 mm thick slabs skirting well be
considered.
13
For Foundations
REINFORCEMENT STEEL:
Providing High yield strength deformed steel bars (Fe 500 ) of different
diameters, cutting, bending to required sizes and shapes placing in position
with cover blocks of approved size, binding wire of 20 SWG, forming grills
for reinforcement work as per approved designs and drawings, including
cost and conveyance of bars from approved manufactures RINL, TISCON or
equivalent, including cost and conveyance of binding wire, cover blocks,
overlaps, chair and all wastages, rusting (quantity for overlaps, chairs,
couplings, welded joints, spacer bars etc will not be measured separately and
are to be accounted in costing ) including drilling boreholes and grouting the
anchor bars wherever necessary and all taxes on all materials, all incidental,
operational, labor charges such as cutting, bending, placing in position, tying
etc., complete for finished item of work.
MS STEEL TRUSS
Providing MS steel truss as per the design with necessary primer & painting
as per the engineers instruction.
15
BOLTS
15.01
Providing foundation bolts of 20mm dia with 600 depth as per the design
and engineers instruction.
No
20
15.02
Providing foundation packet and grouting as per the design and engineers
instruction. ( Bolt will be supplied by GVK Bio)
No
20
15.03
Providing foundation packet and grouting as per the design and engineers
instruction. ( Bolt will be supplied by contractor)
Kg
50
Sqm
70
16
Sheet
Providing and laying of GI powder coated sheet of 0.48mm thick as per
the required color and design.
TOTAL AMOUNT
RPOSE
DATION
APUR.
RATE
AMOUNT
0
0
0
0
0
0