Академический Документы
Профессиональный Документы
Культура Документы
9/21/05
1:39:07 PM
CM
MY
Mechanics Tips
CY
CMY
MT4015EN
Mechanics
Tips
2005 FEBRUARY
Rev. 1 2005 SEPTEMBER
MT4015EN
Allison Transmission
Allison 4th Generation Controls
Printed in USA
NOTES
TABLE OF CONTENTS
SECTION I
INTRODUCTION
SECTION II
PREVENTIVE MAINTENANCE
25 FLUID RECOMMENDATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
26 TRANSMISSION FLUID AND FILTER CHANGE INTERVALS . . . . . . 26
27 TRANSMISSION FLUID CONTAMINATION . . . . . . . . . . . . . . . . . . 30
28 TRANSMISSION FLUID AND FILTER CHANGE PROCEDURE . . . . . 31
29 FLUID LEAK DIAGNOSIS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
210
BREATHER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
211 TROUBLESHOOTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
212 TRANSMISSION STALL TEST . . . . . . . . . . . . . . . . . . . . . . . . . . 42
SECTION III
REMOVING TRANSMISSION
31 DRAINING TRANSMISSION . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
32
DISCONNECTING CONTROLS . . . . . . . . . . . . . . . . . . . . . . . . . . 47
SECTION IV
TRANSMISSION PREPARATION
INSTALLING PTO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
44
45
SECTION V
55
CHECKING CONTROLS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60
SECTION VI
61 HANDLING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64
62 MOUNTING TO ENGINE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64
63 INSTALLING TRANSMISSION MOUNTING COMPONENTS . . . . . . . 65
64
COUPLING TO DRIVELINE . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65
CONNECTING COOLER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67
69
610
611
612
INSTALLATION CHECKLIST . . . . . . . . . . . . . . . . . . . . . . . . . . 70
SECTION VII
71
INSTALLATION CHECKLIST . . . . . . . . . . . . . . . . . . . . . . . . . . . 71
72
SECTION VIII
CUSTOMER SERVICE
81 OWNER ASSISTANCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75
82
SERVICE LITERATURE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75
TRADEMARK USAGE
fi
fi
WARNING:
CAUTION:
NOTE:
fi
INTRODUCTION
fi
Section I
CONVERTER MODULE
TURBINE
PUMP
LOCKUP
CLUTCH/DAMPER
STATOR
V03350.06.00
CONTROL MODULE
ELECTRO-HYDRAULIC
CONTROLS
P1 MODULE
P2 MODULE
CONVERTER MODULE
TURBINE
PUMP
STATOR
LOCKUP
CLUTCH/DAMPER
V07286.01.00
CONTROL MODULE
ELECTRO-HYDRAULIC CONTROLS
P1 MODULE
P2 MODULE
10
CONVERTER HOUSING
MODULE
CONVERTER
HOUSING
CONVERTER MODULE
TURBINE
PUMP
STATOR
LOCKUP
CLUTCH/DAMPER
V07287.04.00
CONTROL MODULE
ELECTRO-HYDRAULIC
CONTROLS
P1 MODULE
P2 MODULE
P3 MODULE
CONVERTER MODULE
TURBINE
PUMP
STATOR
LOCKUP
CLUTCH/DAMPER
V07288.01.00
CONTROL MODULE
ELECTRO-HYDRAULIC CONTROLS
P1 MODULE
P2 MODULE
CONVERTER
HOUSING MODULE
CONVERTER HOUSING
CONVERTER MODULE
TURBINE
PUMP
STATOR
LOCKUP
CLUTCH/
DAMPER
P3 MODULE
P2 MODULE
P1 MODULE
V05641.02.00
MAIN SHAFT
MODULE
MAIN SHAFT
P3 SUN
P2 SUN
REAR COVER
MODULE
REAR COVER
OUTPUT SHAFT
C6 ADAPTER HOUSING
MODULE
C6 ADAPTER HOUSING
C6 CLUTCH
P4 MODULE
BREATHER
ASSEMBLY PADS
PTO
PROVISION
INPUT
SPEED
SENSOR
OUTPUT
SPEED
SENSOR
FEEDTHROUGH HARNESS
CONNECTOR
COOLER PORTS
NAMEPLATE
MAIN-PRESSURE TAP
NOTE: Inch Series Threads
RIGHT-REAR VIEW
BREATHER
TORQUE CONVERTER
WITH LOCKUP CLUTCH
AND TORSIONAL DAMPER
ASSEMBLY PADS
(BOTH SIDES)
MAIN-PRESSURE TAP
NOTE: Inch Series Threads
PTO PROVISION
(AVAILABLE BOTH SIDES)
LEFT-FRONT VIEW
Figure 16. 3000 Product Family
(With PTO Provision)
V07289.01.00
BREATHER
ASSEMBLY PADS
OUTPUT
SPEED
SENSOR
RETARDER
VALVE BODY
CONNECTOR
SUMP
COOLER
PROVISION
MAIN-PRESSURE TAP
NOTE: Inch Series Threads
TACHOGRAPH PROVISION
COOLER PORTS
LEFT-REAR VIEW
BREATHER
TORQUE CONVERTER
WITH LOCKUP CLUTCH
AND TORSIONAL DAMPER
ASSEMBLY PADS
(BOTH SIDES)
OUTPUT
RETARDER
TO RETARDER
ACCUMULATOR
MAIN-PRESSURE TAP
NOTE: Inch series threads
LEFT-FRONT VIEW
Figure 17. 3000 Product Family
(With Retarder)
V07401.01.00
PTO
(TOP RIGHT POSITION)
SHIPPING
BRACKET (3)
MOUNTING
PAD
FEEDTHROUGH
HARNESS
CONNECTOR
ENGINE SPEED
SENSOR
TURBINE SPEED
SENSOR
OUTPUT SPEED
SENSOR
FILL TUBE
NAMEPLATE
COOLER PORTS
RIGHT-REAR VIEW
MOUNTING PAD
(BOTH SIDES)
FEEDTHROUGH
HARNESS
CONNECTOR
PTO
(BOTTOM LEFT
POSITION)
COOLER PORTS
MAIN-PRESSURE TAP
LEFT-REAR VIEW
V07291.01.00
RETARDER
FEEDTHROUGH
HARNESS
CONNECTOR
NAMEPLATE
FILL TUBE
TURBINE
SPEED
SENSOR
ENGINE SPEED SENSOR
RIGHT-FRONT VIEW
MOUNTING PADS
(BOTH SIDES)
PTO (TOP RIGHT POSITION)
RETARDER
SUMP
COOLER
PROVISION
COOLER PORTS
LEFT-REAR VIEW
V07292.01.00
MOUNTING PADS
(BOTH SIDES)
PTO (TOP RIGHT POSITION)
C6 ADAPTER
HOUSING
REAR COVER
LEFT-REAR VIEW
MOUNTING PADS
(BOTH SIDES)
PTO (TOP RIGHT POSITION)
C6 ADAPTER
HOUSING
RETARDER
SUMP
COOLER
PROVISION
MAIN-PRESSURE TAP
LEFT-REAR VIEW
COOLER
PORTS
V07399.01.00
PREVENTIVE
MAINTENANCE
Section II
21.
a. Transmission Inspection.
fi
fl
b. Vehicle Inspection.
fl
c.
fl
Welding.
CAUTION:
fi
must
22.
19
NOTE:
fl
fl
fl
fl
fl
fl
fl
fl
Table 21.
Display Sequence
Interpretation of Display
fl
Table 22.
Display Sequence
N
fl
fl
NOTE:
fi
Table 23.
N
MODE
b.
fl
fi
fl
fl
c.
fl
fl
fi
fl
D
N
fi
fl
fl
fl
fl
fi
d.
fl
fl
fl
fl
NOTE:
fl
fl
FILL
TUBE
HOT
FULL
FILL
TUBE
HOT
ADD
COLD
ADD
COLD
ADD
COLD
FULL
HOT
ADD
COLD
FULL
OIL SUMP
TRANSMISSION/SUMP
DESCRIPTION
F**
106.7 mm
(4.20 in.)
76.2 mm
(3.00 in.)
66.0 mm
(2.60 in.)
132.6 mm
(5.22 in.)
13.8 mm
(0.54 in.)
2.00 in.***
101.6 mm
(4.00 in.)
73.7 mm
(2.90 in.)
50.8 mm
(2.00 in.)
86.6 mm
(3.41 in.)
5.9 mm
(0.23 in.)
4.00 in.***
101.6 mm
(4.00 in.)
63.5 mm
(2.50 in.)
45.7 mm
(1.80 in.)
86.6 mm
(3.41 in.)
5.9 mm
(0.23 in.)
NOTE: Calibrate level marking locations with respect to transmission control module
split line and fill tube.
Scale none.
*Dimension determined by installation.
**Reference dimension only. Actual dimension to be determined by installation.
***Reference drawing AS66-60.
****Reference drawing AS67-60.
V07301.00.01
Figure 21. Standard 3000 and 4000 Product Family Dipstick Markings
e.
Consistency of Readings.
24.
fl
fi
fi
CAUTION:
fi
NEVER
25.
fl
FLUID RECOMMENDATIONS
fl
fl
fications
i3
4
fl
fi
fi
fl
fi
fl
fl
CAUTION:
fl
fl
fl
fl
N
Table 24.
26.
a.
Frequency.
CAUTION: Transmission fluid and filter change frequency is
determined by the severity of transmission service. More frequent
changes can be necessary than recommended in the general guidelines
when operating conditions create high levels of contamination or
overheating.
26
27
Fluid
Main
Lube/
Lube/
Internal
Auxiliary
Fluid
Main
Internal
Auxiliary
Schedule 1. Non-TranSynd/Non-TES 295 Fluid
12,000 Miles 12,000 Miles
Overhaul
12,000 Miles 25,000 Miles 25,000 Miles
Overhaul
25,000 Miles
(20 000 km) (20 000 km)
(20 000 km) (40 000 km) (40 000 km)
(40 000 km)
6 Months
6 Months
6 Months
12 Months
12 Months
12 Months
500 Hours
500 Hours
500 Hours
1000 Hours
1000 Hours
1000 Hours
Recommendations in Schedule 2 are based upon the transmission containing 100 percent TranSynd or TES 295 fluid.
3000 Product Family filter change intervals in Schedule 2 are only valid with the use of Allison Gold series filters.
Flushing machines are not recommended or recognized due to variation and inconsistencies with assuring removal of
100 percent of the used fluid.
Schedule 2. TranSynd/TES 295 Fluid
Overhaul
75,000 Miles
Overhaul
75,000 Miles 150,000 Miles 75,000 Miles
75,000 Miles 75,000 Miles
(120000 km)
(120 000 km) (120 000 km)
(120 000 km) (240 000 km) (120 000 km)
36 Months
36 Months
48 Months
36 Months
36 Months
36 Months
3000 Hours
3000 Hours
4000 Hours
3000 Hours
3000 Hours
3000 Hours
GENERAL VOCATION
Filters
SEVERE VOCATION
Filters
Table 25.
fi
NOTE
fl
fi
fl
4 inch Control Module (3.5 inch approximately)Requires filter kit P/N 29540494
Schedule 2. Recommended Fluid and Filter Change Intervals (TranSynd/TES 295 Fluid)
fi
Lube/
Lube/
Fluid
Main
Internal
Auxiliary
Fluid
Main
Internal
Auxiliary
INITIAL FILTER CHANGE INTERVAL:
Schedule 1. Recommended Fluid and Filter Change Intervals (Non-TranSynd/Non-TES 295 Fluid
GENERAL VOCATION
Filters
SEVERE VOCATION
Filters
Table 26.
General Vocation:
fl
fl
fi
fl
Lube/
Lube/
Main
Internal
Auxiliary
Fluid
Main
Internal
Auxiliary
2 inch Control Module (1.75 inch approximately)Requires filter kit P/N 29540493
Schedule 3. Recommended Fluid and Filter Change Intervals (TranSynd/TES 295 Fluid)
Severe Vocation:
Fluid
GENERAL VOCATION
Filters
SEVERE VOCATION
Filters
Table 26.
b. Abnormal Conditions.
fl
fl
c.
fl
fl
fl
fi
Fluid Analysis.
fl
fl
fl
fl
fi
fl
fl
Table 27.
fi
Test
Limit
fl
fl
27.
a.
Fluid Examination.
fl
fl
fl
b. Water.
fl
fl
fl
fi
NOTE:
c.
Engine Coolant.
fi
d.
fi
Metal.
fl
fi
fi
CAUTION:
fl
fi
28.
a.
Drain Fluid.
NOTE:
fi
WARNING:
fl
fl
fl
fl
fl
fl
fl
fl
b.
Replace Filters.
fi
fi
fi
fi
FILTER
COVER
LUBE
LUBE
MAIN
MAIN
DRAIN
PLUG
LUBE
DRAIN
PLUG
MAIN
6
5
4
3
2
1
V03532.02.02
fi
fi
CAUTION:
c. Refill Transmission.
fi fl
fi
fl
fi
fi
After refill, check the fluid level using the procedure described in Section 23,
TRANSMISSION FLUID CHECK, Paragraph b. Manual Fluid Check Procedure.
Table 28.
Initial Fill*
Refill*
Transmission
Sump
Liters
Quarts
Liters
Quarts
4 inch
27
29
18
19
3000 Product Family
2 inch
25
26
16
17
4 inch**
45
48
37
39
4000 Product Family
2 inch**
38
40
30
31
* Approximate quantities, do not include external lines and cooler hose.
** For transmissions with PTO add 2.8 liters (3 quarts)
29.
a.
35
211.
TROUBLESHOOTING
36
b. Diagnostic Codes.
Table 29.
Code
List
Position DTC
Active* Historic
Check Failure
Trans Record**
fi
fi
fi
DTC.
fi
Active Indicator.
Y
Historic Indicator.
fi
Description
During installation, false codes can be recorded in the TCMs memory. Clear
these codes before road testing the vehicle. Use the shift selector to clear the
codes (Refer to Figure 23).
Enter the diagnostic mode on pushbutton selectors by pressing the (Up)
and (Down) arrow simultaneously. Simultaneously press both buttons
twice if there is an oil level sensor present.
With a lever selector, enter the diagnostic mode by momentarily pressing
the MODE button. Press twice if there is an oil level sensor present.
To clear all active indicators, press and hold the MODE button
approximately 3 seconds until the mode indicator (LED) flashes.
To remove all codes, press and hold the MODE button for approximately
10 seconds until the mode indicator (LED) flashes again.
38
NOTE:
fi
MODE
MODE
MODE
NOTE:
fi
1
2
3
4 6
5 1
D
N
R
HOLD OVERRIDE
BUTTON
MODE INDICATOR
(LED)
MODE BUTTON
HOLD OVERRIDE
BUTTON
MODE ID
DIGITAL DISPLAY*
R
N
D
6 5
1 43
2
1
DISPLAY MODE
DIAGNOSTIC BUTTON
SIX-SPEED,
LEFT-HAND
LEVER SELECTOR
WITH REVERSE
IN REAR
MODE INDICATOR
(LED)
MODE BUTTON
MODE ID
6
1
DIGITAL DISPLAY *
DISPLAY MODE
DIAGNOSTIC BUTTON
SIX-SPEED,
RIGHT-HAND
LEVER SELECTOR
WITH REVERSE
TO FRONT
CONTOURED
BEZEL
DIGITAL DISPLAY *
MODE
MODE ID
MODE
INDICATOR (LED)
Push simultaneously
to enter diagnostic
mode and fluid
level check
6
1
PUSHBUTTON SELECTORS
* NOTE: The first number displayed is highest forward range available and second number is range
attained in selected position.
Visually check to confirm range selected. If display is flashing, shift is inhibited.
fl
V07343.03.01
f.
fi
g.
(Up)
(Down)
N
MODE
212.
a.
Purpose.
fi
NOTE:
b.
fl
WARNING:
fl
fl
fl
fl
fl
WARNING:
c.
fl
OFF
CAUTION:
R
45
g.
46
REMOVING
TRANSMISSION
Section III
47
OUTPUT SPEED
SENSOR
REAR COOLER
PORTS
FRONT COOLER
PORTS
(OPTIONAL)
ACCUMULATOR LINE
TACHOGRAPH
PTO CONTROLS
(AND LINES
IF NECESSARY)
RETARDER
TEMPERATURE
SENSOR
RETARDER
CONNECTOR
FEEDTHROUGH
HARNESS
CONNECTOR
TO
COOLER
FROM
COOLER
TURBINE SPEED
SENSOR
REAR COOLER
PORTS
REMOTE COOLER
MANIFOLD
RIGHT SIDE
V07315.01.00
48
BREATHER
ASSEMBLY PADS
TACHOGRAPH
ENGINE
SPEED
SENSOR
NAMEPLATE
FEEDTHROUGH HARNESS
CONNECTOR
TEMPERATURE SENSOR
SPEED SENSOR
TO COOLER
NOTE: Inch Series Threads
FROM COOLER
NOTE: Inch Series Threads
V07359.01.00
49
If replacing the transmission, you may need to transfer the output flange or yoke
to the replacement transmission. Remove the output flange or yoke by removing
the M14 x 2.0 x 70 bolt, retainer plug, and O-ring.
50
TRANSMISSION
PREPARATION
Section IV
Starter Ring Gear. Check the starter ring gear for excessive wear or damage.
a. Output Oil Seal. Check the output oil seal for leaks or damage. Refer to the
latest edition of the approved Service Manual for replacement instructions. If not
replacing the oil seal, lubricate it with high-temperature grease or transmission
fluid.
CAUTION: DO NOT attempt to polish the oil seal contact surface on
the flange or yoke. Scratches or machine-type lead can cause the seal to
leak.
b. Check Flange or Yoke. Check the flange or yoke for damage or wear. The
oil seal contact surface must be smooth and regular to prevent oil leaking past the
seal. Rotate the flange or yoke after installation to check for binding.
51
c.
43.
INSTALLING PTO
Access to the PTO mounting pads and the space available to maneuver the
transmission determine whether the PTO should be installed before or after the
transmission is installed.
CAUTION: DO NOT use cork or other soft gaskets to install the PTO.
Use only the shims/gaskets listed in the appropriate parts catalogs. Refer
to Table 81 for the latest publication number.
a. Install Guide Pins. Guide pins are included in the PTO manufacturers
installation kit. Determine the required position of the guide pins in relation to the
mounted position of the PTO. The guide pins must align with the two blind holes
in the PTO pad. Install two headless guide pins into the converter-housing PTO
pad. Tighten the pins.
b. Install Gasket. Install the special gasket over the guide pinsribbed surface
away from the transmission.
c. Mount the PTO. Mount the PTO on the guide pins, meshing the PTO driven
gear with the transmission PTO drive gear. Retain the PTO by installing a bolt in
the top bolt hole. Install the remaining bolts. Tighten all bolts to 5161 Nm
(3845 lb ft).
44.
a.
Location.
3000 Product Familyfill tube may be mounted on either the right or left
side. The unused fill tube provision must have a plug to fill the tube
opening.
4000 Product Familyfill tube is on the right side.
52
CAUTION: Install the fill tube bracket with the correct length bolt. A
bolt that is too long may cause cracks and leaks in the main housing.
Refer to the appropriate parts catalog for the correct bolt.
b. Installation. Install the fill tube seal into the main housing. Insert the fill tube
through the seal. Align the tube bracket with its bolt location. Install the fill tube
bolt and tighten to 2429 Nm (1821 lb ft).
On 3000 Product Family transmissions, the unused hole is blocked using a
fill tube seal and a new plug. Install the fill tube seal into the unused fill
tube hole. Install the new plug so that the underside of the plug head
contacts the fill tube seal.
45. CHECKING PLUGS AND OPENINGS
Carefully check all sides and the bottom of the transmission for loose or missing
plugs.
a. Pressure Plugs. Check that 0.437520 UNF-2A pressure plugs are tightened
to 1013 Nm (710 lb ft).
b. Fluid Drain Plug. Check that the drain plug is tightened to 2532 Nm
(1824 lb ft).
c. Cleanliness. Check the openings into which the cooler lines connect for
deformities or obstructions. Check the transmission electrical connectors for
cleanliness. Clean electrical connectors with LPS cleaner only (refer to SIL
17-TR-94).
53
Section V
51.
PREPARING VEHICLE
FOR TRANSMISSION
INSTALLATION
You must make sure a new transmission installation can be adapted to the
vehicles engine. The measurements described in this section provide correct
transmission-to-engine adaptation. Refer to Figure 51 or Figure 52 and/or
AS67020. Typical arrangement of adaptation components is shown in Figure 54.
a.
b. Flywheel Housing Pilot Bore Diameter. The flywheel housing pilot bore
diameter must measure:
3000 Product Family447.68447.81 mm (17.62517.630 inches)
4000 Product Family511.18511.30 mm (20.12520.130 inches)
c. Flywheel Housing Bore Runout. Flywheel housing bore runout cannot
exceed 0.51 mm (0.020 inch) TIR.
d. Flywheel Housing Face Squareness. The flywheel housing face cannot be
out-of-square more than 0.51 mm (0.020 inch) TIR.
e. Crankshaft Hub Pilot or Adapter Diameter. The crankshaft hub pilot or hub
adapter pilot diameter must measure between 50.9450.99 mm
(2.0062.008 inches).
f. Crankshaft Hub Pilot or Adapter Squareness. The crankshaft hub or hub
adapter cannot be out-of-square more than 0.13 mm (0.005 inch) TIR.
g. Crankshaft Hub Pilot or Adapter Concentricity. The crankshaft hub pilot
or the hub adapter pilot concentricity cannot exceed 0.13 mm (0.005 inch) TIR.
54
55
FLYWHEEL HOUSING
SAE STANDARD J617/2
VENT HOLES
12-WASHER
HARDENED STEEL
V03536
4-FLEXPLATE
WEARPLATE
CRANKSHAFT BOLT (Consult engine
manufacturer for torque requirements.)
0.13 mm (0.005 in.)
1.60 mm (0.063 in.) MIN PILOT
MAXIMUM TOTAL
INDICATOR READING
ON CRANKSHAFT
76.28 mm (3.003 in.) MIN
HUB ADAPTER
4.40 mm (0.173 in.) MIN
VIEW B
ENGINE ADAPTATION REQUIREMENTS
FLEXPLATE ADAPTER
VIEW A
TRANSMISSION CONVERTER SPACE CLAIM
56
ACCESS HOLE
FLEXPLATE ADAPTER
FLYWHEEL HOUSING
28-BOLT
M8 x 1.25 x 25.0 mm (0.98 in.) LONG
Torque to 2429 Nm (1721 lb ft)
*Minimum if transmission side mounting pads are not used to mount powerpack.
**Minimum if transmission side mounting pads are used to mount powerpack.
Torque to 7388 Nm (5465 lb ft).
VIEW A
TRANSMISSION CONVERTER SPACE CLAIM
V03537
CONVERTER HOUSING
BOLT, FLEXPLATE-TO-FLEXPLATE ADAPTER
12-M8 x 1.25 x Various lengths
Torque to 2429 Nm (1721 lb ft)
or 6-M10 x 1.5 x Various lengths
Torque to 5161 Nm (3845 lb ft)
0.13 mm (0.005 in.) MAXIMUM TOTAL INDICATOR
READING ON FLEXPLATE ADAPTER
45.92 mm (1.808 in.) Design shall result in the flexplate
outside diameter being deflected 0.38 mm (0.015 in.)
away from engine (measure at location marked +).
See VIEW A for converter position.
4-FLEXPLATE
WEARPLATE
CRANKSHAFT BOLTS (Consult engine manufacturer for
torque requirements.)
VIEW B
ENGINE ADAPTATION REQUIREMENTS
*18-WASHER
**12-WASHER
21-BOLT MIN
IF M10 x 1.5-6H BOLTS ARE USED
Torque to 5161 Nm (3845 lb ft)
*18-BOLT 0.4375-14 UNC-2A
**2-BOLT 0.4375-14 UNC-2A
V01717
57
BALL BEARING
SEALRING
FLEXPLATE
ASSEMBLY
FLEXPLATE
ADAPTER
ENGINE
FLYWHEEL
HOUSING
CRANKSHAFT
HUB ADAPTER
WEAR PLATE
TRANSMISSION
V00533.03.00
Inspect the chassis and driveline components for the following conditions, and
correct them as appropriate:
Transmission mountsbroken or worn-out
Bolts and other hardwardamaged, missing, or incorrect
Isolators (rubber mounts)damaged or missing
Driveline anglesrunout, or balance which does not conform to the
manufacturers recommendations
Driveline yoke slip joints:
freedom of movement
damaged or worn-out
correctly lubricated
correctly indexed
58
59
60
0 Volt
4.444 Volts
0.278 Volts
ERROR
ZONE
5 Volts
0.972 Volts
3.889 Volts
ERROR
ZONE
APPROX.
19 mm (0.75 in.) STROKE
CLOSED
THROTTLE
FULLY
RETRACTED
(AT REST)
8.9 mm
(0.35 in.)
2.5 mm
(0.1 in.)
0 mm
WIDE OPEN
THROTTLE
Total Stroke
CTWOT
15.2 mm22.9 mm
(0.60 in.0.9 in.)
1.6672.500 Volts
35.7 mm
(1.4 in.)
FULLY
EXTENDED
40.6 mm
(1.6 in.)
45.7 mm
(1.8 in.)
V05746.00.02
62
BENDING LOAD
APPLIED
UNACCEPTABLE INSTALLATION
MOUNTING PROVISION:
Use M6 x 1.00 or 14-20 in. series bolts 3 places
Torque M6 x 1.00 bolt to 1013 Nm (84120 lb in.)
1
Torque 4-20 in. series bolts to 1314 Nm (108132 lb in.)
Mount to a solid frame member. Flatness of
chassis mounting surface must not exceed
0.8 mm (0.03 in.).
ACCEPTABLE INSTALLATION
Attachment must provide freedom
of motion to allow cable loading in
tension only (no bending loads).
WIRING HARNESS
55.0 mm (2.17 in.)
MIN REQUIRED
FOR CONNECTION
REMOVAL
FULLY EXTENDED
FORCE REQUIRED
26.7 N (6.0 LB) MAX
FULLY
RETRACTED
CLOSED THROTTLE
95.2 mm (3.75 in.)
MOUNTING
LENGTH
(NOTE: Mounting length
+ 50.8 mm (2 inches) equals
cable length)
118.1 mm
(4.65 in.)
95.2 mm
(3.75 in.)
CLOSED THROTTLE
FULL THROTTLE
160.2 mm (6.31 in.) MIN
SAME AS WITHOUT
SLIP LINK
FULLY EXTENDED
63
Section VI
INSTALLING
TRANSMISSION INTO
VEHICLE
61. HANDLING
a. Preventing Damage. Handle the transmission carefully to prevent damage to
components in the installation path.
b. Control of Transmission Movements. Use a hoist or transmission jack that
allows precise control of transmission movements during installation.
62. MOUNTING TO ENGINE
Use the following procedure to mount the transmission to the engine: (Reference
Figure 54):
1. Align one of the flexplates bolt holes with the access opening in the
engine flywheel housing.
2. Lubricate the center pilot boss with molybdenum disulfide grease
(Molycote G, or equivalent).
3. Install a headless guide bolt into one of the flexplate bolt holes in the
flexplate adapter or torque converter mounting lug (refer to Figure 53).
Align the guide bolt with the flexplate hole at the access opening.
4. Push the transmission toward the engine while guiding the pilot boss on the
torque converter into the flexplate hub adapter and the guide bolt into the
hole on the flexplate.
5. Seat the transmission squarely against the engine flywheel housingno
force is required. If interference is encountered, move the transmission
away from the engine and investigate the cause.
6. Align the bolt holes in the converter housing with those in the engine
flywheel housing.
7. Install all transmission-to-engine bolts finger tight.
CAUTION: The entire converter housing circumference must be flush
against the engine flywheel housing before tightening any bolts. DO
NOT use the bolts to seat the housing.
64
65
RETARDER
ACCUMULATOR
AND MOUNTING
BRACKETS
VEHICLE
WIRING
HARNESS
PRESSURE PROTECTION
VALVE (85 PSIG
MAXIMUM CLOSING
PRESSURE)
Be sure there is an
orifice fitting on
IN-CAB
4000/B 500
TRANSMISSION
installations (and
CONTROLS
is not present on
3000/B 400/B 300
installations).
RETARDER
SOLENOID
NORMALLY
CLOSED
V07302.00.01
If not already mounted, mount the PTO(s) onto the transmission (refer to Section
43, INSTALLING PTO).
1. Check the PTO harness routing for kinks and sharp bends. Avoid routing
the cable close to exhaust pipes or manifold. The PTO harness must not rub
or interfere with adjacent parts.
2. Connect controls to the PTO.
3. Check for proper PTO control operation.
66
CONNECTING COOLER
Refer to Figure 62 for typical cooler port locations on the transmission and
recommended torque for cooler line fittings.
69. CONNECTING ELECTRICAL COMPONENTS
NOTE: Allison Transmission electronic control systems are designed
and manufactured to comply with all FCC and other guidelines
regarding radio frequency interference/electromagnetic interference
(RFI/EMI) for transportation electronics. Manufacturers, assemblers, and
installers of radio-telephone or other two-way communication radios
have the sole responsibility to correctly install and integrate those
devices into Allison Transmission-equipped vehicles to customer
satisfaction. For further information, refer to TS3989EN, the Allison 4th
Generation Controls Troubleshooting Manual.
Remove the cover from the transmission feedthrough connector and
carefully connect the transmission external wiring harness to the 20-way
transmission feedthrough connector. Keep dirt and debris out of the
connector. Tighten the connector bolt to 2.03.2 Nm (1828 lb inch). DO
NOT OVER TORQUE.
Connect the external wiring harness.
For the 4000 Product Family, connect engine, turbine, and output
speed sensors, retarder control connector (if retarder is present), and
the retarder temperature sensor.
67
TO
COOLER
COOLER
TO
RETURN
COOLER
TORQUE 5468 Nm (4050 lb ft)
COOLER
RETURN
REAR VIEW
REAR VIEW
COOLER
RETURN
COOLER
TO
RETURN
COOLER
TORQUE 5468 Nm (4050 lb ft)
TO
COOLER
FRONT VIEW
FRONT VIEW
COOLER
TO
RETURN
COOLER
TORQUE 6881 Nm (5060 lb ft)
COOLER
TO
RETURN
COOLER
TORQUE 6881 Nm (5060 lb ft)
REAR VIEW
REAR VIEW
V07293.01.00
The TCM, through the VIM, provides an electronic speedometer speed signal. If
used, consult the OEM for connection procedures.
611. FILLING HYDRAULIC SYSTEM
1. Select a transmission fluidrefer to Section 25, FLUID
RECOMMENDATIONS.
2. Fill the transmission with the required amount of fluidrefer to Table 28.
69
3. Run the engine for about one minute and check the fluid levelrefer to
Section 23, TRANSMISSION FLUID CHECK, Paragraph c. Cold Check
Procedure.
612.
INSTALLATION CHECKLIST
70
CHECKS AND
ADJUSTMENTS
71.
Section VII
INSTALLATION CHECKLIST
Use this checklist after transmission installation. As items are checked, mark them
off this list.
Torque Values:
All control module bolts5161 Nm (3845 lb ft)
Speed sensor bolts2429 Nm (1821 lb ft)
Flexplate-to-crankshaft hub boltsconsult engine manufacturer
specifications
Flexplate-to-flexplate adapter bolts5161 Nm (3845 lb ft)
Fluid drain plug2532 Nm (1824 lb ft)
Fluid fill tube bracket2429 Nm (1821 lb ft)
Control module pressure taps1013 Nm (710 lb ft)
Cooler fittings:
#12, 3447 Nm (2535 lb ft)
#16, 5468 Nm (4050 lb ft)
#20, 6881 Nm (5060 lb ft)
Cooler port cover bolts5161 Nm (3845 lb ft)
Flexplate adapter-to-converter cover bolts2429 Nm (1821 lb ft)
Output flange bolt7080 Nm (5259 lb ft)
PTO cover bolts5161 Nm (3845 lb ft)
PTO mounting bolts5161 Nm (3845 lb ft)
Breather1216 Nm (912 lb ft)
PTO pressure hose to transmission1013 Nm (710 lb ft)
20-Way transmission feedthrough connector bolt2.03.2 Nm
(1828 lb inch)
Rear cover bolts90110 Nm (6681 lb ft)
71
72
72.
a.
Driveability.
NOTE: Refer to the latest edition of the 3000 and 4000 Product Family
Operators Handbooks or Owners Manuals for operating instructions.
Refer to Section 82, SERVICE LITERATURE for the latest publication
number.
73
c.
74
CUSTOMER SERVICE
Section VIII
75
Table 81.
76
MT4015EN 200509
www.allisontransmission.com