Академический Документы
Профессиональный Документы
Культура Документы
org
Access provided by Rochester Institute of Technology on 03/25/15. For personal use only.
ANNUAL
REVIEWS
Further
Key Words
Abstract
We discuss in this review how the roughness of a solid impacts its wettability.
We see in particular that both the apparent contact angle and the contact angle hysteresis can be dramatically affected by the presence of roughness. Owing to the development of rened methods for setting very well-controlled
micro- or nanotextures on a solid, these effects are being exploited to induce
novel wetting properties, such as spontaneous lmication, superhydrophobicity, superoleophobicity, and interfacial slip, that could not be achieved
without roughness.
71
Controlling the wettability of solid materials is a classical and key issue in surface engineering.
Roughly speaking, two extreme limits are often desired. The rst limit is complete wetting, in
which a liquid brought into contact with a solid spontaneously makes a lm. In the case of a
windshield, for example, this lm maintains the transparency of the glass; in addition, the lm
ows in the gravity eld (if the car is stopped) or due to air friction (when it moves), taking dust
particles with it. The second limit is complete drying: Liquid drops remain spherical without
developing any contact with the substrate. They are thus readily evacuated, which prevents liquid
contamination of the solid surface.
It is of obvious interest to determine which parameters favor both these situations. The basic
laws were rst established for ideal solids, which are both at and chemically homogeneous. As
understood by Young and Laplace, surfaces carry a specic energy, the so-called surface tension,
that reects the cohesion of the underlying condensed phase (either solid or liquid). This quantity,
denoted as IJ for an interface between phases I and J (below the indices are S, L, A for solid,
liquid, and air, respectively), is an energy per unit area and thus a force per unit length: This force
applies along the IJ surface to minimize the corresponding (positive) surface energy. We denote
the liquid/air surface energy simply as .
Hence, we arrive at a construction rst imagined by Marangoni: A lm spreads from a reservoir
of liquid (a drop or a bath) onto a solid, as sketched in Figure 1a, provided that the solid/air
surface tension SA (which entrains this lm) is larger than SL + , the sum of the solid/liquid
and liquid/air surface tensions (which both resist the spreading because complete wetting expands
the two corresponding surface areas). The sign of the spreading parameter S = SA SL
will thus determine the behavior of a drop on a solid: For S > 0, a drop spreads, whereas it forms
a small lens in the opposite case. This lens meets the solid with a well-dened contact angle ,
whose value is similarly given by a force balance (Figure 1b). Projecting on the solid plane the
different surface tensions acting on the contact line provides the equilibrium condition of the drop
(1). The balance at equilibrium can be written as
SA = SL + cos .
1.
The contact angle is thus xed univocally by the chemical nature of the different phases. Here
we show that this statement can be dramatically affected if the solid is rough. We refer below to
the angle as the chemical or Young angle. In many common situations, this angle lies between
0 and 90 (i.e., the hydrophilic case). Very qualitatively, a solid/liquid surface tension (between
SL
SA
SA
SL
Figure 1
Two classical wetting situations for an ideal material. (a) A liquid lm spreads, drawn by the solid/air surface
tension, despite the action of the liquid/air and solid/liquid tensions. (b) Wetting is only partial, and the
balance of surface tensions determines the contact angle .
72
Quere
two condensed phases) tends to be smaller than a solid/air one (with only one condensed phase)
because the phases are less contrasted in the rst case. Hence, a positive cosine in Equation 1
results, implying an acute angle .
Conversely, we could dene a drying parameter D = SL SA . If SL is larger than SA +
, the contact line will be withdrawn by surface forces until a lm of air comes between the solid
and the liquid: D > 0 is the criterion for complete drying. (This criterion is also simply derived
by making cos < 1 in Equation 1.) There is a rst case in which this criterion is fullled:
For a system in which complete wetting is achieved (for example, water on freshly cleaned glass),
inverting the liquid and the air immediately provides D > 0; a bubble of air at the bottom of the
same glass lled with water will completely dewet glass.
In a particular circumstance, the so-called Leidenfrost effect (2), D is forced to vanish: If water
(or any volatile oil) is deposited on a solid whose temperature is much larger than the boiling
temperature of the liquid, a vapor lm forms between the solid and the liquid, which sits on its
own vapor. Considering in Equation 1 that the solid role is played by the vapor, we determine that
D = 0. But the situation is quite different at standard temperatures. Although complete wetting can
be achieved (for example, with most light oils on most solids), complete drying of water (or any oil)
on a at solid is never observed. On the most hydrophobic solids (uorinated materials), the contact
angle never exceeds approximately 120 (3), to which corresponds a negative parameter D (of
approximately /2). We term hydrophobic these situations in which obtuse angles are observed.
Another aim of this review is to show how one can take advantage of the surface roughness for
lling the (large) gap existing between 120 and (nearly) 180 , thus generating ultrahydrophobic
behaviors of obvious practical interest (water repellency).
Figure 2
(a) A liquid brought into contact with a tube or a slot will penetrate it provided that the surface energy of the
tube is lower wet than dry. This means that, as deduced from Equation 1, the contact angle of the liquid on
the tube walls must be acute. (b) Conversely, for an obtuse contact angle, the tube tends to remain dry. If
gravity is present, both the rise and descent are limited.
www.annualreviews.org Wetting and Roughness
73
the tube. As stressed above, contact angles are generally acute, which means that most sponges
absorb most liquids. A system for which we have S > 0 will necessarily satisfy the condition W >
0 (then, the contact angle is zero, indeed smaller than 90 ), and it is worth discussing carefully the
mechanism of invasion in this case. Therefore, as shown in Figure 1a, a liquid lm (typically of
a molecular thickness) progresses along the tube walls (4) such that the meniscus behind the lm
advances on a prewet tube. Because this meniscus suppresses the liquid/air interface as it moves,
the penetration is always favorable. The wicking parameter can be written as W = , which is
indeed the limit of W as the contact angle vanishes, as seen in Equation 1.
Conversely, wicking is not favorable for W < 0, and liquid is expelled from the pore
(Figure 2b)hence the development of the idea that a solid decorated with hydrophobic cavities can remain lled with air, even if the solid is exposed to a liquid, and thus approach the
Leidenfrost limit. As we see, not only can roughness modify the wettability of a solid but also
perhaps the main message of this reviewroughness can result in new and specic properties
such as water repellency. We rst show that the natural roughness of most solids is likely to induce
pinning of the contact line and thus variability of the contact angle (apparently contrasting with
what can be expected from Equation 1). Subsequently, we discuss how special kinds of roughness
(well-designed microstructures) can be created at the solid surface to control both wettability and
pinning and, beyond, special hydrodynamic properties such as slip.
2. ROUGH SOLIDS
2.1. Contact Angle Hysteresis
Most solids are naturally rough, often at a micrometric scale. Processes of fabrication (such as
lamination) may generate striations or microgrooves. Materials resulting from the compaction of
grains exhibit roughness at the scale of the grains. Coating can also induce roughness, in particular
when the coating lm dewets, thus producing microdrops at the surface. Conversely, very few solids
are molecularly at. Most often, molecularly at solids result from solidifying a liquid lm, either
free or suspended on another liquid; in such cases, the roughness can correspond to the thermal
roughness of a liquid interface, generally of the order of a few angstroms. This is the case of glass,
solidied from its molten state after deposition onto a bath of molten tin.
Gibbs pointed out that defects on a solid can pin a contact line. As a consequence, droplets
on an incline stay at rest; the front and rear contact nonwetting and wetting defects, respectively
(5). The resulting asymmetry in contact angles creates a Laplace pressure difference between the
front (of high curvature) and the rear (of smaller curvature) and, thus, a force able to resist gravity
provided that the drop is small enough (6). Both chemical heterogeneities and roughness can act
as pinning sites. It is useful to think of a single defect such as is sketched in Figure 3.
Even on a chemically homogeneous surface, the edge of the defect (of characteristic angle )
makes the contact angle exible at this place. We measure a (Young) angle before the edge and
a (Young) angle + after the edge, considering the horizontal as the reference (we ignore
with our naked eye the existence of the defect). Hence it is possible to have any angle between
and + at the edge (7). A groove can thus stop the front of a liquid drop (as if it were
nonwetting), and a tip will act in the opposite way so that a solid decorated with both kinds of
defects yields both small and large apparent angles.
Contact angles therefore generally depend on the history of the process of liquid deposition.
A drop gently deposited spreads and stops when it is surrounded by primarily nonwetting defects,
which prevent it from exploring the solid further. After a while, the drop evaporates, and thus its
conguration is that of a drop pinned on wetting defects. The way to quantify this contact angle
74
Quere
Figure 3
Apparent pinning of a contact line on an edge. The Young condition stipulates that the liquid meets the solid
with a contact angle . Hence the contact angle at the edge can take any value (if the horizontal direction is
considered as the reference one) between and + , as illustrated by the colored region.
hysteresis consists of slowly increasing the volume of a drop: The contact line rst remains stuck
before it suddenly jumps above a critical volume (for which the line suddenly depins and moves
toward a next series of pinning defects). The maximum observed angle is the so-called advancing
contact angle a . Conversely, sucking the liquid from the drop attens it until it depins and retracts
to the next wetting series of events, which stop and pin the line; the minimum corresponding angle
is the receding contact angle r .
Contact angle hysteresis can be seen as benecial (e.g., when it is exploited for guiding a
ow along a line of defects, following a predened route) or detrimental (e.g., water drops stuck
on window panes distort their transparency and contribute to degradation of the glass). It is thus
crucial to understand it, but there is still a debate about the laws that relate the microscopic picture
(pinning on a single defect) to the macroscopic observations (measurement of the hysteresis, which
averages on many defects). We give further an example of such a calculation. More generally, we
see that the contact angle hysteresis = a r varies dramatically on a rough solid, from
nearly zero to a giant value, of the order of a itself (8).
dx
Liquid
Vapor
Solid
Figure 4
The Wenzel picture. One can obtain the apparent contact angle by considering a small apparent
displacement of the contact line and looking at the corresponding variation in surface energy, assuming that
the liquid follows the accidents of the solid surface.
www.annualreviews.org Wetting and Roughness
75
assumption of the model is sketched in Figure 4: As the contact line progresses on the dry solid,
it is assumed to follow all the topological variations of the material so that each piece of liquid/air
interface gets replaced by a solid/liquid interface of the same surface area. The surface energy
variation dE arising from an apparent displacement dx of the line can be written, per unit length
of the contact line, as
Annu. Rev. Mater. Res. 2008.38:71-99. Downloaded from www.annualreviews.org
Access provided by Rochester Institute of Technology on 03/25/15. For personal use only.
dE = r(SL SA ) dx + dx cos ,
2.
where the second term on the right corresponds to the change of liquid/vapor surface area as the
drop spreads. The roughness increases both the solid energies, enhanced geometrically by a factor
r. The minimum of E (dE = 0) yields Equation 1 if the solid is at (r = 1); if not, we nd (9)
cos = r cos ,
3.
3. MICROTEXTURED SOLIDS
We show in the previous section that roughness modies both the ideal character of the Young
equation (the angle is not unique) and the value of the apparent observed angle. Therefore,
wettability can be tuned by roughness. We can take advantage of roughness to modulate the
surface properties of a solid and, even better, to induce properties that could not be generated
otherwise, a theme that has been extremely popular during the past decade.
Let us quote here three factors that contributed to the burst of this domain. (a) At the end of the
1990s, researchers from the Kao Corporation in Japan showed that extremely large angles could be
obtained by the use of uorinated rough (fractal) surfaces (15, 16). This result was not fully novel;
similar results had been obtained in the 1940s (17) but somehow forgotten (18). (b) At the same
time, Neinhuis and Barthlott in Germany systematically analyzed the structures on the surfaces
of hydrophobic plants. These researchers showed the remarkable variety of the surface designs,
suggesting that nature had optimized the patterns (19, 20). This kind of study was extended to
animals, and new fascinating designs were (re)discovered and discussed (2124). There have since
76
Quere
cos *
been many attempts to mimic these natural patterns so as to understand their efciency. (c) The
recent development of microfabrication techniques allows us today to construct very well-dened
micro- or nanostructures, which has pushed researchers, e.g., to imagine new designs and to
optimize given designs. We now summarize different ndings related to these three factors (ac).
Cosine of the
apparent contact
angle on a
textured surface, as a
function of the
cosine of the Young
angle measured on
the same surface, yet
at (16). The lines
show the behavior
expected from
Equations 3, 10,
and 14.
0
c
cos
www.annualreviews.org Wetting and Roughness
77
regime results from the penetration of the liquid inside the microtextures; this liquid surrounds the
drop on which the contact angle is measured. Then, the lens of liquid sits upon a mixture of solid and
liquid, at odds with the Wenzel hypothesis, which assumes a dry solid beyond the drop, as shown in
Figure 4. We call this second regime superhydrophilic, and we describe this regime in Section 4.
50 m
50 m
50 m
500 nm
Figure 6
A few examples of natural superhydrophobic materials, as revealed by SEM. (a) Leaf of the so-called
elephants ear (Colocasia esculenta). From Reference 39 (courtesy of Peter Wagner and Christoph Neinhuis).
(b) Lotus leaf. Courtesy of Barthlott & Neinhuis (20). (c) Leg of a water strider. From Reference 23 (courtesy
of Lei Jiang). (d ) Surface of a mosquito (Culex pipiens) eye. From Reference 40 (courtesy of Lei Jiang). Note
the difference in scale between panels ac and panel d.
78
Quere
stimulating hypotheses, there is no real understanding for this hierarchical structure, which is not
necessary for reaching very high degrees of hydrophobocity (37). Actually, such structures often
provide both a high contact angle and a low contact angle hysteresis. For lotus, for example, the
advancing angle is approximately 160 , and the receding angle is larger than 150 , which confers
to water drops a high mobility on these leaves. In some cases, such as the rice leaf, the arrangement
of the papillae at the surface can be anisotropic, and thus wetting and adhesion are also anisotropic
(38). On such materials, water will ow preferentially along certain directions.
Feathers of many birds [such as those of pigeons (41) and ducks] are hydrophobic and/or
superhydrophobic, as are insects such as cicada, butteries, and of course water striders (24, 42).
Insects cuticles are covered with a layer of epicuticular wax (of typical thickness of 250 nm),
which prevents the intrusion of water into the body (a serious threat for the insect) and protects
the animals from dessication. Without this protection, the insect rapidly dies if exposed to dry air.
But the most impressive superhydrophobic properties are related to the presence of setae on the
body or on the legs (Figure 6c), allowing some animals to oat on water or even to live underwater
owing to the air spread on their body (4348); see details in the recent and comprehensive review
by Bush et al. (24). The setae often consist of tapered hairs with a length of 30 m, a diameter of
110 m, and an angle of inclination of typically 30 (Figure 6c). As for plants, there is a secondary
texture, namely nanogrooves, whose exact role is still questioned (23). Other structures can be
very different: Figure 6d shows the pattern that decorates the eye of Culex pipiens, the classical
mosquito. It is very simple and well-ordered, at an impressively small scale (posts of size and height
of approximately 100 nm) (40). We show further that some applications indeed require reduction
of the pattern size.
4. HEMIWICKING
Patterns on a hydrophilic solid at a scale much smaller than the capillary length (above which gravity
dominates surface tension effects) can induce superhydrophilicity. We discuss above the Wenzel
effect, in which the roughness enhances hydrophilicity, provided that liquid ts in the pattern
(Figure 4), leaving dry the rest of the solid as in usual partial wetting (Figure 1b). However, the
structures may also guide the liquid within the array they form, in a manner similar to wicking.
The phenomenon that occurs here is not classical wicking but hemiwicking: As the lm progresses
in the microstructures, it develops an interface with air, leaving (possibly) a few dry islands behind
it. We examine the conditions for observing hemiwicking, starting with the case of a single groove.
We discuss how this phenomenon impacts the wetting laws and conclude with a few considerations
of the dynamics of these lms.
www.annualreviews.org Wetting and Roughness
79
10 m
500 nm
5 m
20 m
Figure 7
Different examples of synthetic microtextured surfaces. (a) The simplest possible surface, with regular
micropillars. (Courtesy of M. Reyssat.) (b) A surface decorated with nanobers. From Reference 51 (courtesy
of L. Gao and T.J. McCarthy). (c) A surface planted with carbon nanotubes. From Reference 52 (courtesy of
J. Bico). (d ) Mushroom pattern (with a at hat). From Reference 53 (courtesy of G. McKinley).
4.1. Grooves
As stressed above, many solids are naturally striated by grooves. Such defects can also be etched for
specic purposes, such as directional wetting. We consider, for example, a rectangular groove of
width w and depth , as sketched in Figure 8, in which we ignore the detail of the different menisci.
For observing a spontaneous invasion of the groove, the solid must lower its energy by being
wet ( SL < SA ). But this is not enough because a liquid/vapor interface also develops at the top.
dx
w
Figure 8
A liquid (in blue) invading a rectangular groove on a solid. Here, we ignore the menisci (at the liquid front
and along the corners, ahead of it) and consider a progression of the liquid by a quantity dx.
80
Quere
We expect the interface to be at (as represented in Figure 8), which minimizes the corresponding
surface area. Hence, for a liquid progression in the groove by a quantity dx, the surface energies
change by an amount (ignoring gravity effects)
dE = (SL SA )(2 + w) dx + w dx.
4.
Using the Young equation, we nd that the liquid progression is favorable (dE < 0) if we have
< c ,
5.
with
cos c = w/(2 + w).
6.
Whatever the values of w and , the latter quantity (which depends only on the aspect ratio /w)
denes a number between 0 and 1, from which the angle c can be made explicit. If the groove
is narrow and/or deep (w is small and/or is large), we recover the criterion (discussed above, in
the context of Figure 2) of spontaneous penetration in a classical porous medium: c = 90 . In
a general case ( w), c is somewhere between 0 and 90 : It is more demanding to impregnate
a groove than a 3-D porous medium. This is all the more true because the groove is shallow: As
/w tends toward 0, so does c , meeting the criterion of complete wetting on a at solid.
81
Air
dx
b
h
Liquid
Solid
Figure 10
Liquid lm (in blue) propagating on a solid, within a forest of microposts of height h, mutual distance p, and
radius b. The condition for the progression is deduced from the variation of surface energy associated with it.
The impregnating front should propagate as pictured in Figure 10: The solid is coated by the
liquid on a surface area proportional to r S , whereas the (at) liquid/vapor interface develops
on a surface area proportional to 1 S .
For a lm progressing by a distance dx (larger than the scale of the defects), the variation in
surface energy per unit length perpendicular to the gure can be written as
dE = (SL SA )(r s )dx + LV (1 s ) dx.
7.
The progression is favorable provided (once again) that the Young angle is smaller than a critical
value c , which depends only on the design of the solid (56):
cos c = (1 s )/(r s ).
8.
Liquid invasion on a microstructured solid can thus be tuned by the geometry of the structures.
For dilute defects (small S ), we have cos c 1/r: The rougher the substrate, the larger c , i.e.,
the more likely that hemiwicking occurs. For a substrate composed of disconnected defects (such
as posts), the liquid front must somehow be activated to achieve the jumps sketched in Figure 10.
For wetting liquids, this is made possible via the menisci, which form around each post, allowing the liquid to reach the next row. In other cases, the contact line can remain pinned in a
metastable Wenzel state, and an external source of energy (such as vibrations) must be employed to
nucleate a contact with the next rows of pillars. We can even imagine equilibrium situations in
which the drop coexists with a wet ring of nite extension (looking a bit like a fried egg). If, for
example, the energy barrier is passed owing to the action of the Laplace pressure, the progression
can stop once the drop spreads enough to make its Laplace pressure too small for inducing a
further motion.
We can interpret the second regime (for < c ) in Figure 5 as resulting from hemiwicking.
In this experiment, the solid is very rough, with a fractal structure. Even if we do not know the
value of the parameter S , we expect it to be smaller than 1, so cos c should be of the order of
1/r. The second regime indeed starts close to the abscissa where the Wenzel regime (of slope r)
intercepts the line cos = 1, that is, for cos 1/r. The apparent angle then hardly depends on
, which can be understood qualitatively: The drop sits on a composite surface consisting mainly
of liquid, apart from a few solid islands. The angle should be very close to 0 (the value it would
take if there were only liquid), but it cannot reach this value owing to the islands on which the
angle is > 0. The number of islands should be a function of , which makes it difcult to produce
a general theory. The value expected for the angle is based on Figure 11, in which we sketch
the drop coexisting with the impregnating lm.
We consider a displacement of the contact line by a quantity dx. The solid becomes wet on
a fraction of surface S , and liquid interfaces are eliminated on a fraction 1 S . Because the
displacement also implies an increase of the liquid/vapor interface of the drop, the total change of
surface energies eventually becomes (per unit length of the line)
dE = s (SL SA ) dx (1 s ) dx + dx cos .
82
Quere
9.
dx
Liquid
Solid
Figure 11
Drop coexisting with a lm that self-propagated within the material textures. The apparent angle is obtained
by considering a displacement of the contact line and computing the corresponding variation of surface
energy.
The minimum of E yields the apparent angle , as rst shown by Cassie (57, 58):
cos = 1 (1 s ) cos .
10.
For small S , the angle hardly varies with , as observed in Figure 5 for < c . This variation
is linear when the cosines of both angles are plotted, and the slope provides S . We would deduce,
for example, from Figure 5 that S 0.15. However, the actual behavior should not be linear for
a disordered surface, for which the proportion of emerged islands should itself be a function of
(the smaller the , the smaller the S ), making the actual variation () less simple.
83
is a good way for setting lms of a desired thickness). Then, p is chosen to maximize the speed
of propagation; it will be taken of order h because there is no dynamic benet for having more
compact networks.
5. SUPERHYDROPHOBICITY
5.1. Air Trapping
On hydrophobic solids, the situation is of course different from that for hydrophilic solids. If
the solid is rough enough, we do not expect that the liquid will conform to the solid surface, as
assumed in the Wenzel model (Figure 4). Rather, air pockets should form below the liquid [this is
the so-called Cassie or fakir state (4849)], provided that the energetic cost associated with all the
corresponding liquid/vapor interfaces is smaller than the energy gained not to follow the solid.
This criterion can be made more quantitative by consideration of, again, pillar-like textures. If
the liquid/air interfaces are assumed to be at (which can be justied by a condition of constant
Laplace pressure in the liquid, which, for defects much smaller than the drop size, can be taken
as null), the wet and liquid surface areas are proportional to (r S ) and (1 S ), respectively.
Hence, air pockets are favored, provided that (6365)
(r s ) (SL SA ) > (1 s ) ,
11.
which (through the use of the Young formula) can be reformulated as > c , with
cos c = (1 s )/(r s ).
12.
This criterion is similar to the one established for propagating a lm of liquid inside the texture.
Air here replaces liquid, so the critical angle expected from Equation 12 is just minus the
critical angle below which hemiwicking takes place (Equation 8). For very rough solids (r 1),
this criterion is always satised. Then, c tends toward 90 , and is indeed larger than this
value, because we assumed chemical hydrophobicity. For materials decorated with long hairs, for
example, the roughness factor r 2bh/p2 can typically be 5 to 10 (as deduced from Figures 6c
or 7c, for example). Figure 12 conrms that the leg of Microvelia, a small bug walking on water,
does not contact the liquid, as evidenced by the distance visible between the leg and its reection
(24).
1 cm
Figure 12
(a) A Cassie state in action: Microvelia walking on water (scale bar, 1 cm). (b) Thin (hydrophobic) hairs allow
the bug to be repelled by and to skate on water. From Reference 24 (courtesy of D. Hu and J.W.M. Bush).
84
Quere
dx
Liquid
Air
Solid
Figure 13
Displacing the contact line in the Cassie regime: The energy balance must include the creation of liquid/air
interfaces below the drop, as indicated by the dotted lines.
The situation is more ambiguous for modest roughness factors, such as those provided by
small pillar density S . The chemical contact angle is typically 100 to 110 , and its cosine is
slightly negative. Thus, the criterion for air trapping is not obeyed. However, Cassie states are
often observed in spite of a higher interfacial energy (64, 66, 67). The air present before we place
a drop can remain trapped in a metastable state, as long as the drop does not nucleate a contact
with the ground surface of the solid. We discuss in Section 5.3 the metastability of Cassie states.
This Cassie regime is the one of interest because, in addition to a large contact angle, it provides a
small contact angle hysteresis, owing to the presence of the air cushion. As a consequence, we term
superhydrophobic the only Cassie regime, which generates amazing properties such as reduced
adhesion, water repellency, and slip (partially discussed in Sections 5.2 and 6.3).
Because the drop sits on a mixture of solid and air, we expect a large apparent angle . If
there is only air, Young (Equation 1, where we replace the index S by A) predicts a contact angle
of 180 (i.e., no contact). Any deviation from this value tells us the proportion of solid actually
contacting the liquid.
The variation of interfacial energy arising from a displacement of the contact line by a quantity
dx (as sketched in Figure 13) is related to the creation of new wet solid surface and liquid/vapor
interfaces. The nal balance can be written as
dE = s (SL SA ) dx + (1 s ) dx + dx cos .
13.
14.
This description must be complemented by a (local) Young condition at each contact line (at
the edge of the drop and for each liquid/vapor interface below). This condition is satised by
the presence of edges on the posts (or more generally of large slopes on the rough material). As
discussed above in the context of Figure 3 and because we have > 90 , sharp angles permit
this condition. We expect stronger pinning if these edge angles are smaller: Re-entrant designs
will make more robust Cassie states, and we see below (Section 5.3) that they can even induce air
trapping in a hydrophilic situation (29).
Equation 14 usually predicts large angles. For 110120 and S between 5% and 10%,
we get apparent angles of 160170 . In Figure 14, we see a millimetric water drop on a silicon
www.annualreviews.org Wetting and Roughness
85
Figure 14
Millimetric water drop
on a hydrophobic
surface textured with
regularly spaced
micropillars. The
texture acts as a
diffraction grating,
which induces
structural colors. From
Reference 70 (courtesy
of M. Reyssat).
substrate where silicon micropillars (similar to Figure 7a, with S = 5%) were etched and coated
with a uoropolymer (70). The drop is like a pearl (69, 71), sitting on a solid whose iridescences
reveal the regular array of defects, which diffracts light (structural color) (66, 72, 73). Conversely,
structures much smaller than the wavelength of light yield transparency (7476). This raises the
interesting question of the smallest size generating water repellency, which remains to be solved.
The smaller is S , the larger is . But for a more complex topology, S should be a function of
(69). Conversely, the measurement of in a Cassie situation should provide the solid fraction
s contacting the liquid, a quantity of interest for characterizing not only wetting but also hydrodynamic slip (see Section 6.3) or any properties related to a solid/liquid contact (e.g., electrical or
chemical). In the limit of small S , we note that = (with 1), and Equation 14 rewrites
to
2 cos ( /2)s1/2 ,
15.
whose critical behavior in S emphasizes the difculty for achieving a strict nonwetting situation
( 0). However, Gao & McCarthy (51) approached, and perhaps reached, this limit (within
the uncertainty of the measurements) by using nonwoven assemblies of nanobers (Figure 7b) on
which both the advancing and receding angles were 180 . The same authors reported similar results
for pulverulent hydrophobic solids obtained by compressing commercially available lubricant (37).
In both cases, the texture is submicrometric and quite regular, with smooth rounded defects, which
should induce a very low hysteresisthe quantity we now discuss.
Quere
y
p
2b
Figure 15
In a Cassie state, a drop is likely to pin on the edges of the defects as we displace it. The drop becomes
distorted, and the energy stored in this deformation xes the amplitude of the hysteresis.
defects. Therefore, the shape of the defects or the sharpness of the edges is signicant, as evidenced
16.
We guess that will depend on the shape of the defects (for example, complex contours will
generate a higher , and thus a larger hysteresis, unlike small and rounded defects). For the sake
of simplicity, we assume an equilibrium (Young) angle of 90 ; in addition, our defects are pillars
(or disks) of radius b and mutual distance p (with b p). We thus have S b2 /p2 .
As the line pins on a defect of size b, the drop gets distorted, as shown in Figure 15. Its tails
form surfaces of zero curvature: r = b cosh (x/b); that is, for x b, r 1/2 b exp(x/b). The
deformation is maximum (x = u) for the largest lateral deformation r, i.e., for the typical distance
p between two defects. Hence we get
u b log ( p/b).
17.
The pinning force on a defect f is related to b (the line pins on the contour of each defect): f
b , which yields a relationship between force and deformation,
f u/ log ( p/b).
18.
Equation 18 denes a linear spring of stiffness K = /log(p/b) (84). Hence, there is an energy
= 1/2Ku2 stored in the deformation. The force necessary to move the line can be written, per
unit length, as
F = (cos r cos a ).
19.
www.annualreviews.org Wetting and Roughness
87
20.
The contact angle hysteresis vanishes with the density of defects, but the presence of a logarithm in
Equation 20 makes this behavior quite pathological: At small S , the hysteresis decreases because
there are fewer defects (the linear term), but the logarithm term (slowly) diverges, making the
residual hysteresis appreciable. This result seems to be in agreement with many existing data,
but more remains to be done to check these models quantitatively and to extend them to more
complex patterns.
Hysteresis makes drops stick on solids, despite gravity eld or air ow. A general calculation
of the sticking force is difcult, but a simplied argument allows us to evaluate how the hysteresis
enters this quantity (86). We assume that the rear half of the drop joins the solid with an angle r ,
whereas the front half meets it with an angle a . The capillary sticking force can be written as
(cos r cos a ), denoting l as the radius of the solid/liquid contact (quasi-circular for 1).
Assuming a geometric contact l R (where is the difference between the mean angle and ,
and R is the drop radius) and using Equations 15 and 20, we nd that a drop will move in the
gravity eld (on a vertical window pane) provided that
s3/2 log(1/S ) < R2 2 ,
21.
in which we introduce the capillary length 1 = ( /g)1/2 (2.7 mm for water) and ignore all
the numerical coefcients. Once again, the density of defects is crucial for driving the wetting
properties (here the degree of adhesion of a drop on a solid). As we could guess, small densities are
required for suppressing adhesion. However, such a limit also weakens the stability of the Cassie
state, which we now discuss.
Figure 16
Millimetric water drops of the same volume on a superhydrophobic substrate covered with dilute pillars
(S = 0.01, h = 2 m). The drop on the right was thrown on the substrate, whereas the one on the left was
carefully deposited. As observed, Cassie and Wenzel states (left and right, respectively) can coexist. From
Reference 70 (courtesy of M. Callies).
88
Quere
The rst globule is a Cassie drop (we even see light passing below it), whereas the second one is
in a Wenzel state: On this substrate of small roughness (r 1.1), the contact angle is close to the
Young angle, slightly larger than 90 in this example.
When the Wenzel state is the less energetic one, any perturbation of a Cassie drop can provoke
its transition to this state. Conversely, a Wenzel drop is rmly bound to its stable conguration. It
is of practical importance to quantify the robustness of metastable Cassie states and to understand
the conditions provoking impalement. Obviously, an energy barrier must be overcome to nd the
ground state (8790). One can evaluate this barrier by considering the penetration of a Cassie
drop. Assuming unchanged liquid/vapor interfaces as the drop sinks, the only change in surface
energy corresponds to the (unfavorable) wetting of the posts walls. This implies a (positive) energy
per unit area E = ( SL SA )(r 1) = (r 1) cos (this quantity becomes negative in a
hydrophilic situation). We thus nd an energy barrier E 2bh/p2 cos . It is proportional
to the pillar height h, which appears as a natural parameter for tuning this quantity. The energy
barrier E is generally too large to be overcome by thermal energy (we need defects of molecular
dimensions to get E of the order of kT ). However, the energy can be supplied by pressing on
the drop (66, 90), by vibrating the substrate (91), or by an impact (92, 93). Indeed, the higher the
posts, the larger is the resistance to impalement. Once the liquid penetrates the texture, it remains
strongly pinned, and the printed drop is even able to conform to the network of microposts (92).
Sbragaglia et al. (94) described the dynamics of the Cassie/Wenzel transition as very quick and
following a zipping mechanism: One row of cavities gets lled (in a time of approximately 10 s
on a length of 100 m!) before jumping to the next row. This process is somehow reminiscent of
the progression in a groove sketched in Figure 8. The surface force here involves the creation
of wet surfaces and the suppression of suspended liquid/air interfaces, whereas the resisting force
should be viscous. We thus expect a Washburn law for the progression (see Section 4.3), which can
be extremely quick at the small scale of the phenomenon. For a pattern composed of posts whose
height h is comparable to the pitch p (of approximately 10 m), the typical time for invading a row
of length x scales as x2 / h, of the order of 10 s for water and x = 100 m.
The way in which solid/liquid contacts nucleate for triggering the transition is interesting.
Interfaces above the air pockets are curved, tting the global curvature of the drop (Figure 17). If
the drop becomes small enough, the liquid can reach the underlying solid and then propagate. The
size of a drop should thus impact the drops wetting state. Indeed, small droplets are more likely
to be in a Wenzel state than are large droplets (66), which can also be evidenced by observing the
evaporation of a drop. Then, the drops size varies continuously, and investigators have reported
the existence of a critical radius below which the drop suddenly falls into the Wenzel regime
(95, 96).
Following the notations in Figure 17, the interface curvature scales as /p2 (for h < p). Equating
it with the drop curvature 1/R yields the depth of penetration of the interface inside the texture:
p2 /R; the smaller the drop, the larger is. When it becomes of the order of the pillar height
p
Figure 17
The liquid/vapor interface is curved, owing to the curvature of the drop, but the interface also can be curved
if we apply pressure to the drop. denotes the lowering of the interface below the top of the posts.
www.annualreviews.org Wetting and Roughness
89
h, a solid/liquid contact can nucleate on the bare substrate and propagate if the Cassie state is
metastable. This implies a critical radius for a Cassie drop scaling as (96)
R p 2 / h.
22.
Note that, as deduced from Figure 3, depinning from the edge will also occur if the drop radius is
smaller than p/|cos |, a limiting condition for modest chemical hydrophobicity. Here we assume
that this second condition is screened by the rst one, i.e., p > h/|cos |.
The radius R can be much larger than p if h < p. The Cassie state will be all the more robust
because this critical radius is small (no drops fall in the Wenzel drops, except invisible ones). One
can achieve this in two ways: either by making h large, using micro- or nanobers for decorating
the solids (see Figures 6c and 7c) (96), or by reducing both p and h. Miniaturizing the pattern size
enhances the resistance of the Cassie state, which may explain the existence of such small scales
in many natural materials.
Jiang and coauthors (40) recently reported that the eye of C. pipiens apparently remains dry
even if exposed to tiny drops, as encountered in the foggy and moist environments where these
mosquitoes usually circle. Figure 18 is a close-up of C. pipiens after the mosquito passed through an
aerosol of water droplets. Water condenses on most of the animal, but the eyes remain dry, which
of course preserves its vision (renowned as excellent). Figure 6d displays a microphotograph
of the textures observed on the surface of the eye; these are remarkably small, with p h
100 nm. With these values, we get R 100 nm: A drop at this scale not only is invisible but also
evaporates quasi-instantaneously. In a cloud, drops are quite polydisperse, with a typical radius
of 10 msuch small drops would impale on most microtextured surfaces but might resist the
Wenzel transition for the nanopattern worn by the mosquitos eye.
Other promising metastable Cassie states are those obtained on hydrophilic materials with
a particular design. Oils having contact angles of the order of 40 can be suspended on special
textures, producing an increase of the angle by approximately 100 (the superoleophobic effect)
(53, 97102). As shown by Herminghaus, fakir wetting drops are possible on overhangs or reentrant angles, that is, sites where a hydrophilic Young condition can be satised (29). Fibers
and defects with overhangs do provide quite robust oleophobicity and are able to resist a Wenzel
transition by pressing on the liquid with the Laplace pressure related to the size of the holes
Figure 18
Close-up of Culex
pipiens after exposure
to water aerosol.
Droplets condense on
the antennas, but the
black eyes remain
drya condition for
preserving the eyesight
of the insect. From
Reference 40 (courtesy
of L. Jiang).
90
Quere
at the surface. With structures with pronounced re-entrant proles, such as those displayed in
Figure 7d (where the pattern evokes a mushroom, or a hoodoo), Tuteja et al. (53) spectacularly
reported that even a liquid as wetting as octane can be suspended in a Cassie state with advancing
and receding contact angles as high as 160 and 140 , respectively.
6. SPECIAL PROPERTIES
As we see above, hydrophobic Cassie materials generate high contact angles and small hysteresis,
ideal conditions for making water drops very mobile. We conclude this article by discussing a few
special properties potentially generated by these surfaces, such as anisotropy, wettability switches,
and slip.
6.1. Anisotropy
Many natural (Figure 6a,b,d ) and synthetic (Figure 7a,b,c,d ) textures are isotropic. However,
it can be interesting to design directional structures, such as arrays of parallel grooves or microwrinkles, that consequently generate anisotropic wetting, in particular, in the Cassie regime
(69, 103105). Owing to a differential pinning of contact lines, the contact angles (and the hysteresis) are quite different along and perpendicular to the grooves. Axial motion is preferred, and
such designs are appropriate when liquid must be guided.
There are examples of such patterns in nature (38, 41, 106), as in Figure 19, which shows the
scales covering the wings of the buttery Papilio ulysses. Both the arrangement and microtexture of
the tiles contribute to the directionality of this material. Another kind of anisotropy is exploited
by water striders (see its inclined hairs in Figure 6c): Striders strike the surface perpendicular to
the grooves, which generates a large contact force, before swinging the legs by 90 to align them
in the direction of the motion for skating. Motion will arise from alternating pinning and gliding
events (24).
Figure 19
The wings of Papilio
ulysses. The way the
tiles are displayed
together with the
detail of the texture
confer anisotropy to
the texture. From
Reference 106
(courtesy of S.
Berthier).
100 m
www.annualreviews.org Wetting and Roughness
91
Textured surfaces undergo a brutal change of wettability as the contact angle exceeds 90
(Figure 5). This behavior can be exploited to achieve superhydrophobic/superhydrophilic
switches. Different physicochemical effects affecting the solid wettability, such as light on photocatalytic textures (107, 108) or heat for temperature-sensitive coatings (109), can be used for
triggering the transition. The comprehensive review by Feng & Jiang (50) provides details.
Electric eld, as we have learned from Lippman, also affects wettability. Applying a voltage
across a drop lowers its contact angle, and this effect is amplied on a textured surface. A drop
with an angle of approximately 160 can nearly spread under the action of modest voltages (approximately 10 V) (73). However, the liquid gets irreversibly pinned in the superhydrophilic state
(or in any state in which it intimately contacts the rough solid), contrasting with our expectations
for a switch. Krupenkin et al. (110) proposed to use a short and intense pulse of current (through
a thin conductive layer on the sample), which evaporates the liquid close to the surface, hence
restoring a Cassie-suspended state. More generally, there is today no clear example of a Wenzel
state (even potentially metastable) spontaneously transforming into a Cassie state. This situation
is detrimental as a vapor condenses: This naturally forces a Wenzel situation, which often evolves
toward mixed and ambiguous Cassie/Wenzel situations (111115). Much remains to be done to
achieve genuine antidew materials.
Figure 20
The slip length is the distance inside the solid for which the velocity prole of a owing liquid vanishes.
92
Quere
Figure 21
Slip length on
superhydrophobic
patterns of
nanotubes of
constant density, but
with a varying pitch.
In the Cassie state
(circles), the slip
length is
micrometric and
increases with the
pitch. In the Wenzel
state (squares), there
is no measurable slip.
(m)
1.5
0.5
0
0
p (m)
Using microparticle imaging velocimetry, Joseph et al. (122) directly measured slip lengths for water owing on hydrophobic carbon nanotubes. As shown in Figure 21, the slip length dramatically
depends on the nature of hydrophobicity. In a Wenzel state (induced by pressing on the liquid),
there is no measurable slip, in agreement with the paper of Richardson (123), who stipulated that
roughness kills any (potential) slippage if the liquid conforms to it. Conversely, micrometric slip
lengths are observed in the Cassie state, and increase linearly with the post distance p, in these
experiments performed at constant S . This slip can be dramatically damped if liquid/air interfaces
are curved (as in Figure 17), owing, for example, to a pressure exerted on the liquid (124).
It is natural to expect a large slip in a Cassie situation: Liquid glides on air, owing to the large
viscosity ratio between water and air (typically a factor of 100). However, part of the liquid contacts
the top of the posts, which limits the total slip on the surface. We can make this argument more
quantitative, following a recent analysis by Ybert et al. (125). For a ow of typical velocity V, the
size affected by the presence of a post should scale as b, the post radius (b p, the pitch of the
post array). The friction force per pillar, and thus per surface area p2 , should scale as Vb, denoting
as the liquid viscosity. This yields a viscous stress Vb/p2 . This stress dominates the one
arising from the underlying air ow, provided that Vb/p2 > a V/h, in which we introduced the
air viscosity a . Hence there is a geometric requirement, bh/p2 > a /, which can be achieved by
adjusting the post height h. With water, a / is of the order of 102 , and the latter criterion will
be satised with posts of characteristics b = 1 m, h = 10 m, and p = 10 m, for which the
factor bh/p2 is 101 . As seen in Figure 20, the stress can also be written as V/, from which we
deduce an effective slip length :
1/2
p 2 /b p/S .
23.
For a constant pillar density S , is linear with the pillar spacing p, as seen in Figure 21. For
b p ( S 1), we expect very large slip lengths, compared with the values found on at solids.
will typically be between a few p, i.e., 110 m (as reported experimentally), 1000 times larger
than the slip length on a at hydrophobic solid! If air friction dominates the pillar friction (h <
a p2 /b), the slip length becomes h/a , which can be very large as well.
The contact angle is also determined by the density S (Equation 14), so and should
be correlated. At small S , we note = . Introducing Equation 22 in Equation 15 [where
www.annualreviews.org Wetting and Roughness
93
24.
which directly connects the quality of the nonwetting with the amplitude of the slip.
It is of obvious practical interest to maximize the slip and thus to work with low post densities.
However, we see that the liquid in this limit is likely to sink inside the texture, provoking a
complete failure of the slip properties. There again, there is an optimum to nd, and the design
to be given to the microstructures might itself be questioned. The design can also induce slip
anisotropy. If grooves are considered, for example, slip is expected to be larger along the grooves
than perpendicular to them. One can prove that the slip length (which is again of the order of p,
the distance between grooves) differs by a factor of two in both directions (126128), reecting
the factor-of-two difference of the viscous force on a slender object (such as a cylinder) in both
directions.
7. CONCLUSION
Textured surfaces, which provide superwetting, superslip, and superhydrophobicity, are supersurfaces. But so what? After a decade of intense research, we have hundreds of materials for which
drops behave in the eccentric ways we described, but there is no real large-scale application (contrasting with many other smart surfaces, such as self-cleaning ones, for example). The fragility
of these materials (in both a mechanical sense and a thermodynamic sense) seems to limit industrialization. Conversely, the textures in the natural world can be repaired and protected from
contamination (insects spend an appreciable part of their existence grooming their legs). However, there may be short-term applications for synthetic materials, such as disposable devices (for
microuidics) or temporary surface treatments with microbeads (sticking on the material and
forming there the desired microstructures)both cases in which aging is not a major obstacle.
On a more fundamental point of view, many interesting questions remain unsolved, among
which we select (a) the question of the reduction of sizeit would be useful to quantify how
the wetting properties vary as the size of microtextures vanishes; (b) the question of optimization:
What is the best of the microstructures, according to the searched application? We need to dene
a battery of tests to build a classication of the existing textures, before going further to more
detailed models; (c) the search for new properties, such as antidew, for which the use of exible
microbers seems promising; and (d ) a quantitative understanding of contact angle hysteresis,
which remains to be fully done. As we see, wetting and roughness should continue to play their
entertaining game with each other in the coming years!
DISCLOSURE STATEMENT
The author is not aware of any biases that might be perceived as affecting the objectivity of this
review.
ACKNOWLEDGMENTS
It is a real pleasure to thank Anne-Laure Biance, Jose Bico, Aurelie Lafuma, Mathilde Reyssat,
and Denis Richard for the many exchanges on pearl drops. I also thank Yong Chen, Chieko
Ishino, Anne Pepin, and Ko Okumura for stimulating collaborations. I am very grateful to Herve
Arribart, Serge Berthier, Lyderic Bocquet, John Bush, Christophe Clanet, Lichao Gao, Stephan
Herminghaus, L. Mahadevan, Thomas McCarthy, Glen McHale, Gareth McKinley, Lei Jiang,
94
Quere
Christoph Neinhuis, and Julia Yeomans for precious discussions and providing documents for this
report. Finally, the help of A. Dechy and V. Dolies regarding the pictures was greatly appreciated.
LITERATURE CITED
1. Young T. 1805. An essay on the cohesion of uids. Philos. Trans. R. Soc. A 95:6587
2. Leidenfrost JG. 1996. On the xation of water in diverse re. Int. J. Heat Mass Trans. 9:115366
3. Shafrin EG, Zisman WA. 1964. Upper limits to the contact angles of liquids on solids. In Contact Angle,
Wettability and Adhesion: Advances in Chemistry Series, Vol. 43, ed. RF Gould, pp. 14557. Washington,
DC: Am. Chem. Soc.
4. De Gennes PG. 1985. Wetting: statics and dynamics. Rev. Mod. Phys. 57:82763
5. Furmidge CGL. 1962. Studies at phase interfaces. 1. The sliding of liquid drops on solid surfaces and a
theory for spray retention. J. Colloid Sci. 17:309314
6. Dussan VEB, Chow RTP. 1983. On the ability of drops or bubbles to stick to nonhorizontal surfaces of
solids. J. Fluid Mech. 137:129
7. Oliver JF, Huh C, Mason SG. 1977. Resistance to spreading of liquids by sharp edges. J. Colloid Interface
Sci. 59:56881
8. Johnson RE, Dettre RH. 1964. Contact angle hysteresis. I. Study of an idealized rough surface. In
Contact Angle, Wettability and Adhesion: Advances in Chemistry Series, Vol. 43, ed. RF Gould, pp. 11235.
Washington, DC: Am. Chem. Soc.
9. Wenzel RN. 1936. Resistance of solid surfaces to wetting by water. Ind. Eng. Chem. 28:98894
10. Swain PS, Lipowsky R. 1998. Contact angles on heterogeneous surfaces: a new look at Cassies and
Wenzels laws. Langmuir 14:677280
11. Wolansky G, Marmur A. 1998. The actual contact angle on a heterogeneous rough surface in three
dimensions. Langmuir 14:529297
12. Wolansky G, Marmur A. 1999. Apparent contact angles on rough surfaces: the Wenzel equation revisited.
Colloids Surf. A 156:38188
13. Borgs C, de Coninck J, Kotecky R, Zinque M. 1995. Does the roughness of the substrate enhance
wetting? Phys. Rev. Lett. 74:229294
14. Checco A, Guenoun P, Daillant J. 2003. Nonlinear dependence of the contact angle of nanodroplets on
contact line curvature. Phys. Rev. Lett. 91:186101
15. Onda T, Shibuichi S, Satoh N, Tsujii K. 1996. Super-water-repellent fractal surfaces. Langmuir 12:2125
27
16. Shibuichi S, Onda T, Satoh N, Tsujii K. 1996. Super water-repellent surfaces resulting from fractal
structure. J. Phys. Chem. 100:1951217
17. Norton FJ. 1945. U.S. Patent No. 2,386,259
18. Gao L, McCarthy TJ. 2006. Articial lotus leaf prepared using a 1945 patent and a commercial textile.
Langmuir 22:59986000
19. Neinhuis C, Barthlott W. 1997. Characterization and distribution of water-repellent, self-cleaning plant
surfaces. Ann. Bot. 79:66777
20. Barthlott W, Neinhuis C. 1997. Purity of the sacred lotus, or escape from contamination in biological
surfaces. Planta 202:18
21. Wagner T, Neinhuis C, Barthlott W. 1996. Wettability and contaminability of insect wings as a function
of their surface sculptures. Acta Zool. 77:21325
22. Parker AR, Lawrence CR. 2001. Water capture by a desert beetle. Nature 414:3334
23. Gao X, Jiang L. 2004. Biophysics: water-repellent legs of water striders. Nature 432:36
24. Bush JWM, Hu D, Prakash M. 2008. The integument of waterwalking arthropods: form and function.
Adv. Insect Physiol. 34:11792
25. Pliny the Elder. 2004. Natural History: A Selection, transl. ed. JF. Healey. London: Penguin. Rev. ed.
26. Dufour L. 1833. Recherches Anatomiques et Physiologiques sur les Hemipt`eres Accompagnees de Considerations
Relatives a` lHistoire Naturelle et a` la Classication de Ces Insectes. Extr. Mem. Savans Etrang., Tome IV.
Paris: Impr. Bachelier
www.annualreviews.org Wetting and Roughness
95
27.
28.
29.
30.
31.
32.
33.
34.
35.
36.
37.
38.
39.
40.
41.
42.
43.
44.
45.
46.
47.
48.
49.
50.
51.
52.
53.
54.
55.
56.
96
Quere
Fogg GE. 1944. Diurnal uctuation in a physical property of leaf cuticle. Nature 154:515
Cassie ABD, Baxter S. 1945. Large contact angles of plant and animal surfaces. Nature 155:2122
Herminghaus S. 2000. Roughness-induced nonwetting. Europhys. Lett. 52:16570
Minko S, Muller M, Motornov M, Nitschke M, Grundke K, et al. 2003. Two-level structured self-adaptive
surfaces with reversibly tunable properties. JACS 125:3896900
Patankar NA. 2004. Mimicking the lotus effect: inuence of double roughness structures and slender
pillars. Langmuir 20:8209213
Shirtcliffe NJ, McHale G, Newton MI, Chabrol C, Perry CC. 2004. Dual-scale roughness produces
unusually water-repellent surfaces. Adv. Mater. 16:192932
Shirtcliffe NJ, McHale G, Newton MI, Perry CC. 2005. Wetting and wetting transitions on copper-based
superhydrophobic surfaces. Langmuir 21:93743
Gao L, McCarthy TJ. 2006. The lotus effect explained: two reasons why two length scales of topography
are important. Langmuir 22:296667
Bhushan B, Jung YC. 2006. Micro- and nanoscale characterization of hydrophobic and hydrophilic leaf
surfaces. Nanotechnology 17:275872
Nosonovsky M. 2007. Multiscale roughness and stability of superhydrophobic biomimetic interfaces.
Langmuir 23:315761
Gao L, McCarthy TJ. 2007. A commercially available perfectly hydrophobic material. Langmuir 23:9125
27
Wang R, Hashimoto K, Fujishima A, Chikuni M, Kojima E, et al. 1999. Photogeneration of highly
amphiphilic TiO2 surfaces. Adv. Mater. 10:13538
Wagner P, Furstner R, Barthlott W, Neinhuis C. 2003. Quantitative assessment to the structural basis
of water repellency in natural and technical surfaces. J. Exp. Bot. 54:12951303
Gao XF, Yan X, Yao X, Xu L, Zhang K, et al. 2007. The dry-style antifogging properties of mosquito
compound eyes and articial analogues prepared by soft lithography. Adv. Mater. 19:221315
Bormashenko E, Bormashenko Y, Stein T, Whyman G, Bormashenko E. 2007. Why do pigeon feathers
repel water? Hydrophobicity of pennae, CassieBaxter wetting hypothesis and CassieWenzel capillarityinduced wetting transition. J. Colloid Interface Sci. 311:21216
Lee W, Jin MK, Yoo WC, Lee JK. 2004. Nanostructuring of a polymeric substrate with well-dened
nanometer-scale topography and tailored surface wettability. Langmuir 20:766569
Thorpe WH. 1950. Plastron respiration in aquatic insects. Biol. Rev. 25:34490
Noble-Nesbitt J. 1963. Transpiration in Podura aquatica L. (Collembola, Isotomidae) and the wetting
properties of its cuticle. J. Exp. Biol. 40:681700
Heckman CW. 1983. Comparative morphology of arthropod exterior surfaces with the capability of
binding a lm of air underwater. Int. Rev. Gesamten Hydrobiol. Hydrogr. 68:71536
Vogel S. 2006. Living in a physical world. VIII. Gravity and life in water. J. Biosci. 30:30922
Marmur A. 2006. Underwater superhydrophobicity: theoretical feasibility. Langmuir 22:14002
Shirtcliffe NJ, McHale G, Newton MI, Perry CC, Pyatt AJ. 2006. Plastron properties of a superhydrophobic surface. Appl. Phys. Lett. 89:104600
Nakajima A, Hashimoto K, Watanabe T. 2001. Recent studies on superhydrophobic lms. Monatshefte
Chim. 132:3141
Feng X, Jiang L. 2006. Design and creation of superwetting/antiwetting surfaces. Adv. Mater. 18:306378
Gao L, McCarthy TJ. 2006. A perfectly hydrophobic surface. JACS 128:905253
Lau KKS, Bico J, Teo KBK, Chhowalla M, Amaratunga GAJ, et al. 2003. Superhydrophobic carbon
nanotube forests. Nano Lett. 3:17015
Tuteja A, Choi W, Ma M, Mabry JM, Mazzella SA, et al. 2007. Designing superoleophobic surfaces.
Science 318:161822
Ishino C, Reyssat M, Reyssat E, Okumura K, Quere D. 2007. Wicking within forests of micropillars.
EPL 79:56005
Courbin L, Denieul E, Dressaire E, Ajdari A, Roper M, et al. 2007. Imbibition by polygonal spreading
on microdecorated surfaces. Nat. Mater. 6:66164
Bico J, Tordeux C, Quere D. 2001. Rough wetting. Europhys. Lett. 55:21420
57.
58.
59.
60.
61.
62.
63.
64.
65.
66.
67.
68.
69.
70.
71.
72.
73.
74.
75.
76.
77.
78.
79.
80.
81.
82.
83.
84.
85.
86.
87.
88.
89.
90.
Cassie ABD, Baxter S. 1944. Wettability of porous surfaces. Trans. Faraday Soc. 40:54650
Cassie ABD. 1948. Contact angles. Discuss. Faraday Soc. 3:1116
Washburn EW. 1921. The dynamics of capillary ow. Phys. Rev. 17:27383
Cazabat AM, Cohen-Stuart MAC. 1986. Dynamics of wetting: effects of surface roughness. J. Phys.
Chem. 90:584549
Apel-Paz M, Marmur A. 1999. Spreading of liquids on rough surfaces. Colloids Surf. A 146:27379
Rye RR, Mann JA, Yost FG. 1996. The ow of liquids in surface grooves. Langmuir 12:55565
Bico J, Thiele U, Quere D. 2002. Wetting of textured surfaces. Colloids Surf. A 206:4146
Patankar N. 2003. On the modeling of hydrophobic contact angles on rough surfaces. Langmuir 19:1249
53
Alberti G, DeSimone A. 2005. Wetting of rough surfaces: a homogenization approach. Proc. R. Soc.
London Ser. A 461:7997
Lafuma A, Quere D. 2003. Superhydrophobic states. Nat. Mater. 2:45760
Marmur A. 2004. The lotus effect: superhydrophobicity and metastability. Langmuir 20:351719
Rathgen H, Sugiyama K, Ohl CD, Lohse D, Mugele F. 2007. Nanometer-resolved collective micromeniscus oscillations through optical diffraction. Phys. Rev. Lett. 99:214501
Bico J, Marzolin C, Quere D. 1999. Pearl drops. Europhys. Lett. 47:22026
Callies M, Quere D. 2005. On water repellency. Soft Matter 1:5561
Oner
D, McCarthy TJ. 2000. Ultrahydrophobic surfaces. Effects of topography length scales on wettability. Langmuir 16:777782
Gu ZZ, Uetsuka H, Takahashi K, Nakajima R, Onishi H, et al. 2003. Structural color and the lotus effect.
Angew. Chem. Int. Ed. 42:89497
Krupenkin TN, Taylor JA, Schneider TM, Yang S. 2004. From rolling ball to complete wetting: the
dynamic tuning of liquids on nanostructured surfaces. Langmuir 20:382427
Tadanaga K, Katata N, Minami T. 1997. Formation process of superwater-repellent Al2 O3 coating lms
with high transparency by the sol-gel method. J. Am. Ceram. Soc. 80:104042
Nakajima A, Fujishima A, Hashimoto K, Watanabe T. 1999. Preparation of transparent superhydrophobic boehmite and silica lms by sublimation of aluminum acetylacetonate. Adv. Mater. 11:136568
Nakajima A, Hashimoto K, Watanabe T, Takai K, Yamauchi G, et al. 2000. Transparent superhydrophobic thin lms with self-cleaning properties. Langmuir 16:704447
Richard D, Quere D. 2000. Bouncing water drops. Europhys. Lett. 50:76975
Extrand CW. 2002. Model for contact angles and hysteresis on rough and ultraphobic surfaces. Langmuir
18:799199
McHale G, Shirtcliffe NJ, Newton MI. 2004. Contact-angle hysteresis on superhydrophobic surfaces.
Langmuir 20:1014649
Extrand CW. 2006. Designing for optimal water repellency. Langmuir 22:171114
Gao LC, McCarthy TJ. 2006. Contact angle hysteresis explained. Langmuir 22:623437
Kusumaatmaja H, Yeomans JM. 2007. Modeling contact angle hysteresis on chemically patterned and
superhydrophobic surfaces. Langmuir 23:601932
DeSimone A, Grunewald N, Otto F. 2007. A new model for contact angle hysteresis. Netw. Heterog.
Media 2:21125
Joanny JF, de Gennes PG. 1984. A model for contact angle hysteresis. J. Chem. Phys. 81:55262
Pomeau Y, Vannimenus J. 1985. Contact angle on heterogeneous surfaces: weak heterogeneities.
J. Colloid Interface Sci. 104:47788
Quere D, Azzopardi MJ, Delattre L. 1998. Drops at rest on a tilted plane. Langmuir 14:221316
Patankar NA. 2004. Transition between superhydrophobic states on rough surfaces. Langmuir 20:7097
102
Ishino C, Okumura K, Quere D. 2004. Wetting transitions on rough surfaces. Europhys. Lett. 68:41925
Barbieri L, Wagner E, Hoffmann P. 2004. Water wetting transition parameters of peruorinated substrates with periodically distributed attop microscale obstacles. Langmuir 23:172334
Carbone G, Mangialardi L. 2005. Hydrophobic properties of a wavy rough substrate. Eur. Phy. J. E
16:6776
www.annualreviews.org Wetting and Roughness
97
91. Bormashenko E, Pogreb R, Whyman G, Bormashenko Y, Erlich M. 2007. Vibration-induced CassieWenzel wetting transition on rough surfaces. Appl. Phys. Lett. 90:201917
92. Reyssat M, Pepin A, Marty F, Chen Y, Quere D. 2006. Bouncing transitions on microtextured materials.
Europhys. Lett. 74:30612
93. Bartolo D, Bouamrirene F, Verneuil E, Buguin A, Silberzan P, et al. 2006. Bouncing or sticky droplets:
impalement transitions on superhydrophobic micropatterned surfaces. Europhys. Lett. 74:299305
94. Sbragaglia M, Peters AM, Pirat C, Borkent BM, Lammertink RGH, et al. 2007. Spontaneous breakdown
of superhydrophobicity. Phys. Rev. Lett. 99:156001
95. McHale G, Aqil S, Shirtcliffe NJ, Newton MI, Erbil HY. 2005. Analysis of droplet evaporation on a
superhydrophobic surface. Langmuir 21:1105360
96. Reyssat M, Yeomans JM, Quere D. 2008. Impalement of fakir drops. EPL 81:26006
97. Morra M, Occhiello E, Garbassi F. 1989. Contact angle hysteresis in oxygen plasma treated
poly(tetrauoroethylene). Langmuir 5:87276
Quere
119. Ou J, Rothstein JP. 2005. Direct velocity measurements of the ow past drag-reducing ultrahydrophobic
surfaces. Phys. Fluids 17:103606
120. Truesdell R, Mammoli A, Vorobieff P, van Swol F, Brinker CJ. 2006. Drag reduction on a patterned
superhydrophobic surface. Phys. Rev. Lett. 97:044504
121. Roach P, McHale G, Evans CR, Shirtcliffe NJ, Newton MI. 2007. Decoupling of the liquid response of
a superhydrophobic quartz crystal microbalance. Langmuir 23:982330
122. Joseph P, Cottin-Bizonne C, Benoit JM, Ybert C, Journet C, et al. 2006. Slippage of water past superhydrophobic carbon nanotube forests in microchannels. Phys. Rev. Lett. 97:156104
123. Richardson S. 1973. On the no-slip boundary condition. J. Fluid Mech. 59:70719
124. Steinberger A, Cottin-Bizonne C, Kleimann P, Charlaix E. 2007. High friction on a bubble mattress.
Nat. Mater. 6:66568
125. Ybert C, Barentin C, Cottin-Bizonne C, Joseph P, Bocquet L. 2007. Achieving large slip with superhydrophobic surfaces: scaling laws for generic geometries. Phys. Fluids 19:123601
126. Philip JR. 1972. Flows satisfying mixed no-slip and no-shear conditions. Z. Angew. Math. Phys. 23:35370
127. Philip JR. 1972. Integral properties of ows satisfying mixed no-slip and no-shear conditions. Z. Angew.
Math. Phys. 23:96068
128. Lauga E, Stone HA. 2003. Effective slip in pressure-driven Stokes ow. J. Fluid Mech. 489:5577
99
AR347-FM
ARI
2 June 2008
14:10
Annual Review of
Materials Research
Contents
ix
AR347-FM
ARI
2 June 2008
14:10
Current Interest
Combinatorial Materials Sciences: Experimental Strategies
for Accelerated Knowledge Discovery
Krishna Rajan p p p p p p p p p p p p p p p p p p p p p p p p p p p p p p p p p p p p p p p p p p p p p p p p p p p p p p p p p p p p p p p p p p p p p p p p p p p p p p p 299
Bamboo and Wood in Musical Instruments
Ulrike G.K. Wegst p p p p p p p p p p p p p p p p p p p p p p p p p p p p p p p p p p p p p p p p p p p p p p p p p p p p p p p p p p p p p p p p p p p p p p p p p p p 323
Contents
Annual Reviews
Its about time. Your time. Its time well spent.
Complimentary online access to the first volume will be available until January 2015.
table of contents:
Access this and all other Annual Reviews journals via your institution at www.annualreviews.org.