Академический Документы
Профессиональный Документы
Культура Документы
1 CC Command
1.1 PRM Parameter configuration command (Reference code Prmlpub.c):
1) ShowPrm:
Arguments detailed
a) bIsBpOk [BP_MAX]:
byMskChgState:
byMskChgState 0 BP veneer that the parameters of all the carrier is not configured or has been
configured go back to the ACK a;
Low 12-bit bitmap, respectively, the BP card is not bound to the carrier frequency in the
configuration parameters;
Highest profile DSPAddr parameters that do not return ACK; highest participation low one
that configuration BUC
Number, there did not return ACK.
c) DWORD dwBitmap;
dwBitmap 0 carrier on behalf of BP load for all the veneer back ACK;
dwBitmap low 12 BIT with each BP 12 FUTrx corresponding veneer, bit 1 for this photo
FuTrx for carrying, is waiting for response, response to the ACK, then this bit bitmap clear
0.
d) BYTE byL2State:
CC Communications and BP is normal, 1 link links, 0 links broken, FF link
status unknown;
e) tPrmCtlVar.tBpIns [3]. tSynPnt.bySub:
Examples of synchronization reference point
typedef enum tagESynbase (
SYNBASE_IDLE, / * 0: no sync * /
SYNBASE_PWRON, / * 1: power on report submitted to synchronize * /
SYNBASE_SET, / * 2: SET synchronization * /
SYNBASE_GET, / * 3: GET synchronization * /
SYNBASE_TST * 4: TST synchronization * /
) TESynbase;
2) ShowTrxInBp
byBPIndex: view the wireless configuration of the cell and binding
of BP transceiver board (byBPIndex) carrier
Enter telnet CC 6 slots ShowTrxInBp 2 shows the carrier bound BP board as follows:
CC-> ShowTrxInBp 2
tOldAllTrxInPerBp.byBandTrxNum = 6!
BPTrxindex = 0, SectorNo = 1, TrxNo = 1, IPTBSetupFlag = 0, NeedIpTbFlag = 1!!
BPTrxindex = 1, SectorNo = 1, TrxNo = 2, IPTBSetupFlag = 0, NeedIpTbFlag = 1!!
Arguments detailed
a.
b.
c.
d.
BPTrxindex corresponding BP board DSP's Index (0-11), SectorNo and TrxNo cell
binding and the corresponding carrier transceiver
bIPTBSetupFlag: said bearing is established, one that set up, 0 not established
byNeedIpTbFlag:
telnet CC type ShowBoardFlag 1 shows a plot of all the TRX configuration is as follows
CC-> ShowBoardFlag 1
tGetBoardInfoAck. [1] [0] -> bPhyLogOK = 1, bIPTBBracsOK = 1, bIQCfgOK = 1!!!
tGetBoardInfoAck. [1] [1] -> bPhyLogOK = 1, bIPTBBracsOK = 1, bIQCfgOK = 1!!!
tGetBoardInfoAck. [1] [2] -> bPhyLogOK = 1, bIPTBBracsOK = 1, bIQCfgOK = 1!!!
tGetBoardInfoAck. [1] [3] -> bPhyLogOK = 1, bIPTBBracsOK = 1, bIQCfgOK = 1!!!
tGetBoardInfoAck. [1] [4] -> bPhyLogOK = 1, bIPTBBracsOK = 1, bIQCfgOK = 1!!!
tGetBoardInfoAck. [1] [5] -> bPhyLogOK = 1, bIPTBBracsOK = 1, bIQCfgOK = 1!!!
Arguments detailed
a) tGetBoardInfoAck. [cell number] [transceiver number], where transceiver number is
started from 0
b) bPhyLogOK physical logic is configured: 1 for configuration
Arguments detailed
Command ShowBoardFlag, ShowPrm, ShowTrxInBp have stated above, while ShowBitmap see
ShowPrm in dwBitmap.
tRuTruPos: (3,1,1,1)
************************************************** *************************
a.
Arguments detailed
bySectorNo cell number, byFHMode configuration hopping mode: 1, said base-band
frequency hopping, and 2 radio frequency hopping, if configured as a base-band
frequency hopping, the following also print out a list of the baseband frequency.
c.
tBpTruPos and tRuTruPos: BP's carrier and the RRU that the carrier channel
corresponding IQ
tBpTruPos: (1,1,4,0): BpRackNo, BpShelfNo, BpSlot, CHIQID (CH IQ channel number 0,1,2 ....,
11)
tRuTruPos: (3,1,1,1): RuRackNo, RuShelfNo, RuSlot, byTruNo (RU internal carrier
0,1,2 ... ...., 6)
2) dbtr 52 shows platform database access BP and FS of the corresponding relationship between IQ
CC-> dbtr 52
Table [R_CHSWIT] record (Primary Memory: 2)
************************************************** *****************************
byRackNo (*) byShelfNo (*) bySlotNo (*) byDirection (*) byCHIQID (*) byFSPortID (*) byFSIQID (*)
byFSSlotNo (*) byFSRackNo byFSShelfNo byUsedFlg byServType dwStatus
************************************************** *****************************
1140000311110
1141000311110
stop at: 2
Arguments detailed
a.
byRackNo (BP board rack where the number) byShelfNo (chassis number) bySlotNo (slot
number),
b.
c.
d.
e.
f.
g.
h.
i.
3) dbtr 53 shows platform database access RRU and FS of the corresponding relationship between
IQ
CC-> dbtr 53
Table [R_RRUSWT] record (Primary Memory: 2)
************************************************** ***************************
byRackNo (*) byShelfNo (*) bySlotNo (*) byDirection (*) byFSPortID (*) byFSIQID (*) byRRURackNo
byRRUShelfNo byRRUSlotNo byRuTxID byServType dwStatus
************************************************** *****************************
113000311010
113100311010
stop at: 2
Arguments detailed
a.
byRackNo (FS plate rack where the number) byShelfNo (chassis number) bySlotNo (slot
number)
b. byRRURackNo (RRU board where the rack number) byRRUShelfNo (chassis number)
c.
rncmac = 00-d0-d0-a0-69-12,
bpmac = 40-00-c0-fc-04-20
index = 3, vlanid = 65535, Qos = 0x0, rncport = 16643, nodebport = 21387,
rncip = 118.18.1.3, nodebip = 118.18.1.111, bpip = 193.252.4.32,
rncmac = 00-d0-d0-a0-69-12,
bpmac = 40-00-c0-fc-04-20
Parameter Description
a) index0 to 3 represents the 4-way bearing
b) rncport IBSC the port number, nodebport BTS port number
c) rncip IPABIS's IP address, nodebip CC's IP address, bpip BP's DSP IP address of the
primary nuclear
d) rncmac IBSC's IPBB board MAC address, bpmac BP board MAC address
2) BspShowUdpCount port (port number): see the corresponding upper and lower load line data
can be located up and down the silent
Parameter Description
a.
a.
Parameter Description
CurLogTrxNum: Current number of configurable logic carrier, OldLogTrxNum: The last time
the number of configurable logic carrier
b) byTrxIndex index number, CurRRUPos [3,1,1,1] the current physical configuration of the
RRU of the rack number, chassis number, slot number, carrier number
c) bIsNeedIQCfg: the need for IQ configure flags, 0 do not
2) ShowBandTable n: View the current database (TTrx) in the RU and the binding
relationship between BP, n said the configuration of the BBU LMT uniform
number of physical carrier
telnet CC type
ShowBandTable 1
CC-> ShowBandTable 1
bIsBand = 1,
Bp [1,1,4,0],
Ru [3,1,1,2]
Parameter Description
a.
b. Bp [1,1,4,0]: BP rack number, chassis number, slot number, CHIQ number (DSP Carrier)
Ru [3,1,1,2]: RU rack number, chassis number, slot number, carrier number
Parameter Description
AD operating state (1 block, 2 solutions closed), OP operating state (1 block, 2
solutions closed), AV can state
AV Status:
# Define AV_AD_DIFFERENCE (BYTE) 0x10 / * issued to BP status timeout * /
# Define AV_FS (BYTE) 0x04 / * IQ binding before and after the state * /
Parameter Description
(1,1,0 xff): FU state
(1,1, TS): 8 time slots of the state
3) DbsShowTableRecord
and type of veneer
Parameter Description
a) byRackNo (*) byShelfNo (*) bySlotNo (*) single board position
b) wBoardType veneer type
(WORD16) 153
Value
Explanation
dwStatus
Bit2 ~ Reservation
Bit7
Bit0 = Fault / normal
1/0
Bit1 = Where the veneer failure / normal (only AAL2, AAL5 and
1/0
E1, the local district, tower up)
Bit2 = Remote manual occlusion / de-closed, if this bit,
1/0
indicating the remote manual occlusion. (AAL2 use)
Bit3 = The main reserve, on the CCS effective, RBI effective
1/0
when used in B09/B09A
Bit4 = Initialize / normal
1/0
Bit5 = Not available / available; on the veneer is as
1/0
follows:
B09/B09A/B06C/B03C: only WDDL invalid.
Bit6 = Test / normal
1/0
Bit7 = Under the power / normal
1/0
Bit8 = Amplifier Disable / amplifier enable; current RTR
1/0
series of single board, HPA series of single board,
LPA series veneer effective
Bit9 = Did not shake hands with the RNC / RNC to shake hands
1/0
with the success of
Bit10 ~ Reservation
Bit31
CC-> ShowAIFAlm 0
AIFAlm BitMap:
0,0,0,0,0,0,0,0,0,0,0,0,0
Parameter Description
1) The first 0 downlink data is reported FPGA, 0 for no alarm, 1 for alarm.
2) representatives of the other 12 0 12 IQ channel, is detected by the DSP to the uplink data.
2) ShowBoardState (BYTE byRack, BYTE byShelf, BYTE bySlot) shows the state veneer and veneer type
Parameter Description
# Define ENABLED
3) ShowGspsAlm
(BYTE) 0x02
CC-> ShowGspsAlm
AL_PRM_DIF_ALMCODE: 0
AL_RD_PRM_ALMCODE: BPIndex0 ~ 4:0,0,0,0,0
AL_L3NORES_ALMCODE: BPIndex0 ~ 4:0,0,0,0,0
AL_IQ_ERROR_ALMCODE: 0
AL_IPTB_ERROR_ALMCODE: 0
AL_REQ_RFPRM_TIMEOUT: 0
Parameter Description
These are the 6 GSPS detection alarm, 0 for no warning, a report on behalf of a
warning
CC-> OmsAlmMan
Parameter Description
By AlmMapDumpAlmInfo command can query to each alarm bit map veneer
7.
CC-> ShowReboot
Reset Type:
1, the watchdog reset.
2, the software reset. Divided into:
1) normal soft reset (reboot function, such as manual input, or high-level application
software download called reset function reset itself) 2) abnormal soft reset (such as
data resulting from cross-border anomalies, etc.).
3, the hardware power-down reset.
4, CPU reset pin reset pulse signal received. RST by veneer on the front panel reset
button, this is the case.
2) ShowUserMem order to retain the memory view, unusual for reset record
o
o
Reset the record carrier is to retain the information memory and reset the log
Reset the log acquisition method re: ftp to the main control board, and from the
/ ROOT / log directory for OssRec.log (the current log) and OssRecBak.log (earlier
log backup)
CC-> version
VxWorks (for ZTE MPC8360 BOARD) version 5.5.2.
Kernel: WIND version 2.6.
Made on Aug 17 2008, 01:13:02.
Boot line:
qefcc (0,0) host: vxWorks e = 192.252.1.16 h = 192.1.1.1 u = cca pw = cca tn = cca
o
Parameter Description
a.
b.
2) ShowBMCVersion: Displays the current operating specifications package version number and
store location information
CC-> ShowBMCVersion
Run BMC Version ------------- 4.00.020b
Run BMC File Length --------- 3940847
Bak BMC Version ------------- 4.00.021a
Bak BMC File Length --------- 3901559
Running Status -------------- boot normal
Run Package Path ------------ / ROOT/sw2 /
Run Package Version --------- 4.00.020b
Bak Package Path ------------ / ROOT/sw1 /
Bak Package Version --------- 4.00.021b
o
Parameter Description
a.
b.
c.
d.
3) SwShowName: show the version of the specification package version number corresponding to
the version of the name
CC-> SwShowName
================================================== ======
D = 00048, H = 0x00030, SW_CSA, CSA veneer Software
D = 65584, H = 0x10030, SW_CSA_FPGA, CSA veneer FPGA software
D = 00096, H = 0x00060, SW_BPC, BPC veneer Software
D = 65632, H = 0x10060, SW_BPC_FPGA, BPC veneer FPGA software
D = 524384, H = 0x80060, SW_BPC_DSP, BPC single board DSP software
D = 262196, H = 0x40034, SW_AMC_MMC, BPC, FSA veneer MMC Software
D = 327732, H = 0x50034, SW_AMC_MMC, BPC, FSA veneer MMCBOOT Software
D = 00052, H = 0x00034, SW_FSA, FSA veneer Software
D = 65588, H = 0x10034, SW_FSA_FPGA, FSA veneer FPGA software
D = 00069, H = 0x00045, SW_RTR, RTR veneer Software
D = 65605, H = 0x10045, SW_RTR_FPGA, RTR veneer FPGA software
D = 524357, H = 0x80045, SW_RTR_DSP, RTR single board DSP software
D = 393285, H = 0x60045, SW_RTR_EPLD, RTR veneer EPLD Software
D = 00209, H = 0x000d1, SW_TTR, TTR veneer Software
D = 65745, H = 0x100d1, SW_TTR_FPGA, TTR veneer FPGA software
D = 524497, H = 0x800d1, SW_TTR_DSP, TTR single board DSP software
D = 00208, H = 0x000d0, SW_DTR, DTR Single Board Software
D = 65744, H = 0x100d0, SW_DTR_FPGA, DTR veneer FPGA software
D = 524496, H = 0x800d0, SW_DTR_DSP, DTR single board DSP software
D = 00097, H = 0x00061, SW_UBPG, UBPG veneer Software
D = 65633, H = 0x10061, SW_UBPG_FPGA, UBPG veneer FPGA software
a) Open the packet capture tool Ethereal, capture used in small networks where the network
card, click the start be.
b) filter on the knock ip.addr == 118.18.1.3 (ibsc access ip address, this can
be in the background ibsc IP information in global variables found. different
circumstances will be different)
3) telnet CC type M88E61XXDelMonitor 0,8
Role: Use complete packet capture tool, to cancel the CC abis port to
the debug port on the image, or can not connect to the CC on LMT
2. UBPG command
2.1 BUC command (refer to code BucInfo.c)
1) BucShowPhyAndLogInfo: Display physical logic, that logic TRX
binding of BP-board DSP channel (0 - 11).
o
1126
Parameter Description
a.
b.
TruNo: DSP DSP channel number that corresponds to the 12-channel carrier
BtsNo (Cell No.) And TrxNo (transceiver No.): The logical DSP channel
bonding and the transceiver cell
<BTS Attribute>
ItfLvBnd: 0,10,15,20,25,63
ItvPrd: 31
Connetion fail Criterion: 1, value: 64,0,0
RACHLdIndPrd: 2, RACHLdThd: 80, RACHBusyThd: 47
PCHLdIndPrd: 2, PCHLdThd: 80
T3105_SDCCH: 28, T3105_TCH: 10, Ny1: 8
BCCH ARFCN: 51
bIsSateAbis: 1
BSIC: 53
bPageExtActived: 0
bExIndication: 0
byFHMode: 1
PCTestPeriod: 240
bGprsSupported: 0
bEgprsSupport: 0, bEgprsPacketChReqSupport: 0, bDTMSupport: 0
bPageCoordinationSupport: 0, bIRSupportUp: 0, byPCUFrameType: 0
byPpchOvldIndPrd: 0
byRachAccessMin: 0, by8PSKLowerLevel: 0, byTaMin: 0, byTaMax: 0
wTrxFuncMode: 0, bySiteType: 18
Parameters:
byDlevHqave: 6
byUqualHqave: 6
byDqualHqave: 6
byPCDLevWeight: 2
byPCDQualWeight: 2
byPCULevWeight: 2
byPCUQualWeight: 2
byLRxLevUL: 22
byURxLevUL: 30
byLRxQualUL: 2
byURxQualUL: 0
byLRxLevDL: 26
byURxLevDL: 34
byLRxQualDL: 2
byURxQualDL: 0
byPCULIncrLevN: 4
byPCULDecrLevN: 4
byPCULIncrQualN: 4
byPCULDecrQualN: 4
byPCDLIncrLevN: 4
byPCDLDecrLevN: 4
byPCDLIncrQualN: 4
byPCDLDecrQualN: 4
byPCULIncrLevP: 3
byPCULDecrLevP: 3
byPCULIncrQualP: 3
byPCULDecrQualP: 3
byPCDLIncrLevP: 3
byPCDLDecrLevP: 3
byPCDLIncrQualP: 3
byPCDLDecrQualP: 3
byMsTxPwrMax: 39
byMsTxPwrMin: 39
byBsTxPwrMin: 10
bRapidUpPCInd: 1
bRapidDownPCInd: 0
bFastAverageInd: 2
byPCMinInterval: 0
byFreqBand: 24
abyPwrDecrLimit: 22,20,18,16,14,12,10,2
byIncreaseStep: 2
byDecreaseStep: 99
o
Parameter Description
BYTE byUqualHqave; / * average uplink bit error rate measurement data cycles * /
BYTE byDqualHqave; / * measurement data downlink bit error rate of cycle * /
BYTE byPCDLevWeight; / * for the power control downlink RXLEV weighted coefficient * /
BYTE byPCDQualWeight; / * for the power control downlink RXQUAL weighted coefficient * /
BYTE byPCULevWeight; / * for uplink power control weighting coefficient RXLEV * /
BYTE byPCUQualWeight; / * for uplink power control weighting coefficient RXQUAL * /
BYTE byLRxLevUL; / * up power caused by the increase in RXLEV low threshold * /
BYTE byURxLevUL; / * lead to lower RXLEV high uplink power threshold * /
BYTE byLRxQualUL; / * up power caused by the increase in RXQUAL low threshold (value tends
to 7) * /
BYTE byURxQualUL; / * up power caused by reduced RXQUAL high threshold (value tended to 0) *
/
BYTE byLRxLevDL; / * caused by the increased downlink power RXLEV low threshold * /
BYTE byURxLevDL; / * lead to lower RXLEV high downlink power threshold * /
BYTE byLRxQualDL; / * caused by the increased downlink power RXQUAL low threshold * /
BYTE byURxQualDL; / * lead to lower RXQUAL high downlink power threshold * /
BYTE byPCULIncrLevN; / * uplink L_RXLEV_UL threshold compared with the use of treatment as
the samples * /
BYTE byPCULDecrLevN; / * uplink U_RXLEV_UL threshold compared with the use of treatment as
the samples * /
BYTE byPCULIncrQualN; / * uplink L_RXQUAL_UL threshold compared with the use of treatment
as the samples * /
BYTE byPCULDecrQualN; / * uplink U_RXQUAL_UL threshold compared with the use of treatment
as the samples * /
BYTE byPCDLIncrLevN; / * L_RXLEV_DL downlink threshold compared with the use of treatment
as the samples * /
BYTE byPCDLDecrLevN; / * U_RXLEV_DL downlink threshold compared with the use of treatment
as the samples * /
BYTE byPCDLIncrQualN; / * L_RXQUAL_DL downlink threshold compared with the use of treatment
as the samples * /
BYTE byPCDLDecrQualN; / * U_RXQUAL_DL downlink threshold compared with the use of
treatment as the samples * /
BYTE byPCULIncrLevP; / * uplink threshold compared with L_RXLEV_UL handle the number used in
P*/
BYTE byPCULDecrLevP; / * uplink threshold compared with U_RXLEV_UL handle the number used
in P * /
BYTE byPCULIncrQualP; / * uplink threshold compared with L_RXQUAL_UL handle the number used
in P * /
BYTE byPCULDecrQualP; / * uplink threshold compared with U_RXQUAL_UL handle the number
used in P * /
BYTE byPCDLIncrLevP; / * the downlink compared with L_RXLEV_DL treatment threshold used in
the P number * /
BYTE byPCDLDecrLevP; / * the downlink compared with U_RXLEV_DL treatment threshold used in
the P number * /
BYTE byPCDLIncrQualP; / * the downlink compared with L_RXQUAL_DL treatment threshold used
in the P number * /
BYTE byPCDLDecrQualP; / * the downlink compared with U_RXQUAL_DL treatment threshold used
in the P number * /
BYTE byMsTxPwrMax; / * MS in the serving cell in the maximum allowable transmit power (dbm) *
/
BYTE byMsTxPwrMin; / * MS in the serving cell in the minimum allowable transmission power
(dbm) * /
BYTE byBsTxPwrMin; / * BTS in the service district in the minimum allowable transmission
power (level) * /
BOOLEAN bRapidUpPCInd; / * whether uplink fast power control * /
BOOLEAN bRapidDownPCInd; / * whether downlink fast power control * /
BOOLEAN bFastAverageInd; / * whether the fast average * /
BYTE byPCMinInterval; / * power control the minimum time interval * /
BYTE byFreqBand; / * TRX-band, GSM and DCS in the same power level corresponds to a different
power dbm. * /
BYTE abyPwrDecrLimit [8]; / * decrease the maximum power, 8 corresponding to different signal
quality grade 8 different values. * /
BYTE byIncreaseStep; / * Step up * /
BYTE byDecreaseStep; / * steps down * /
) TPCPrmAttr;
ARFCN: 51,
TN7 byChComb: 255, byTSC: 0, byHSN: 0, byMAIO: 0
ARFCN: 51,
Parameter Description
a) byChComb channel combinations, the specific definition:
# Define
TCHHALF
(BYTE) 0x01
# Define
TCHHALF2
(BYTE) 0x02
UBPG-> BucShowRTPLinkID 0
CS RTP LinkID: 21384
CS RTCP LinkID: 21385
PS RTP LinkID: 21386
PS RTCP LinkID: 21387
o
Parameter Description
a.
b.
CS RTP LinkID: CS service port number, investigation and need to use the
port number silent
PS RTP LinkID: PS service port number
c) CS RTCP LinkID and PS RTCP LinkID: With road traffic channel, the current
system has not been achieved
6) void BucShowAIFCfg (BYTE byTruNo): View AIF channel configuration
o
Parameters:
a.
b.
typedef struct
(
WORD16 wARFCN; / * frequency, if the frequency meaningless, compared to
0xFFFF * /
WORD16 wChannelBit; / * channel bitmap with 16 bits to describe the
carrier / frequency channel occupied by the situation. Bit 0 corresponds
to channel 0, bit 1 corresponds to channel 1, and so on. Corresponding
bit is 1, that occupy this channel * /
) TAifConfig
7) void BucShowTruState (BYTE byTruNo): View byTruNo of FU, and various state TS
o
BUC AD state: 2
TN0 AD state: 2
TN1 AD state: 2
TN2 AD state: 2
TN3 AD state: 2
TN4 AD state: 2
TN5 AD state: 2
TN6 AD state: 2
TN7 AD state: 2
Parameters:
a.
b.
8) void BucShowCCAddr (): see BUC access to the IP and MAC address CC,
o
CC IP Addr: 193.252.1.16
CC MAC Addr: 40:0: c1: fc: 1:10
9) void BucShowDspAddr (): View DSP3 a core of user plane and control plane of IP and MAC
address
o
Parameters:
a.
IP address allocation:
BBU all IP and MAC address of veneer are calculated by the CC. For UBPG
single IP and MAC address of the board, CC calculated after configuration to
the BP CPU, then CPU write I2C years. BP DSP loaded after reboot I2C access to
the CC from the user plane IP and MAC address, BP CPU and its own IP and MAC
address.
b.
192 for the control surfaces that address, 193 address that the user
plane
Parameters:
a. DSP cfg syn point: The last time BUC to DBB synchronization point; BUC
will detect if there are parameters to change, will be issued to the DBB
parameters.
b) DSP cfg syn table: 1 (TrxAttr), 1 (FHSAttr), 1 (CommLink),
1 (TrxChnState), both as a representative of four parameters are
synchronized to the DBB, to 0 for parameter is not synchronized
c) OAMM synchronization DBB parameters:
i) TRX attributes:
BucShowInfoHelp
1.BucShowPhyAndLogInfo
2.BucShowBTSAttrs (BYTE byTruNo)
3.BucShowPwrCtrlPrm (BYTE byTruNo)
4.BucShowChnAttrs (BYTE byTruNo)
5.BucShowRTPLinkID (BYTE byTruNo)
6.BucShowAIFCfg (BYTE byTruNo)
Simple way to enter the command: for example, view the physical logic
command BucShowPhyAndLogInfo, can also be used BucShowInfo 1;
View the carrier state BucShowTruState 0 0 can also be used BucShowInfo 6, 0
alternative.
5121100010
576,100,000
640,100,000
704,100,000
768,100,000
832,100,010
16384200120
UB info for User Ub Pool!
#######################
-UBSize-TotalNum UsedNum-MaxUsed-Lack
64,100,000
128,100,000
256,100,000
512,400,000
960,500,000
39,681,000
o
Parameters:
a) Sys Ub Pool System Pool Group: General for the message when the application memory,
or internal use of OSS.
b) User Ub Pool User Pool Group: General users OSS_GetUB application from the pool.
c) UB pool run out of ways to judge: When TotalNum (the number of all UB)
field value == UsedNum (the number of used UB) field value, it means you run
out of a pool of UB.
3. FS command
3.1 FS board commonly used commands
1) DumpFsIQCfgPara: Display FS IQ configuration parameters panel
FS-> DumpFsIQCfgPara
************************************************** ******************
Total Number: 12
byServType byBspCHIQID byDirection byFsPortID byFsIQID byOpType
1540200
1541200
1560210
1561210
1570220
1571220
1580230
1581230
1590240
1,591,240
1550250
1551250
************************************************** ******************
o
Parameters:
FS-> DumpFsRruAddrCfgPara
-------------------------------------------------- -------------byFibPortId = 0
byRruNum = 1
byRackNo = 3
byShelfNo = 1
bySlotNo = 1
byRruId = 3
abyRruFiberMacAddr = 64.0.200.252.0.3
abyRruFiberIpAddr = 200.252.0.3
abyRruFiberIpMask = 255.0.0.0
abyLeftMchIpAddr = 192.252.1.16
abyRightMchIpAddr = 192.252.2.16
abyFsFiberIpAddr = 200.252.3.254
o
Parameters:
ucRruId: RRU ID
abyRruFiberMacAddr: RRU optical port MAC address
abyRruFiberIpAddr: RRU optical port IP address
abyRruFiberIpMask: RRU optical port IP mask
abyLeftMchIpAddr: CSA 1 slot IP address
abyRightMchIpAddr: CSA 2 slot IP address
abyFsFiberIpAddr: Fs optical port IP address
FS-> d 0x610020c0
610020c0: 0001 0000 0002 0000 0003 0000 0005 0000 *................*
610020d0: 0004 0000 0000 0000 0030 0000 0035 0000 *......... 0 ... 5 ..*
610020e0: 0031 0000 0032 0000 0033 0000 0034 0000 *. 1 ... 2 ... 3 ... 4 ..*
610020f0: 0000 0000 0000 0000 0000 0000 0000 0000 *................*
61002100: 0,000,000,000,000,000 0,000,000,000,000,000 *................*
61002110: 0,000,000,000,000,000 0,000,000,000,000,000 *................*
61002120: 0,000,000,000,000,000 0,000,000,000,000,000 *................*
61002130: 0,000,000,000,000,000 0,000,000,000,000,000 *................*
61002140: 0,000,000,000,000,000 0,000,000,000,000,000 *................*
61002150: 0,000,000,000,000,000 0,000,000,000,000,000 *................*
61002160: 0,000,000,000,000,000 0,000,000,000,000,000 *................*
61002170: 0,000,000,000,000,000 0,000,000,000,000,000 *................*
61002180: 0,000,000,000,000,000 0,000,000,000,000,000 *................*
Parameters:
a) Each FS optical port 24 ports
1, the corresponding optical port port number 0-23
2 optical port corresponding to port number 24-47
3 Light exit port number corresponding to 48-51
4 optical port port number corresponding to 52-75
5, optical port corresponding to port number 76-89
Corresponding optical port on the 6th port number 90-113
b) a representative of an IQ channel WORD32 are:
000100001 1 Luminous exit port
000,200,001 Luminous exit port 2
000,300,001 Luminous exit port 3
000,500,001 Luminous exit port 5
000,400,001 Luminous exit port 4
000,000,001 Luminous exit port 0
0030000048 that corresponds to the 3rd light exit port 0
0035000053 light that corresponds to the 3rd exit port 5
0031000049 light that corresponds to the 3rd exit port 1
0032000050 light that corresponds to the 3rd exit port 2
0033000051 light that corresponds to the 3rd exit port 3
0034000052
0034000052
4. RRU command
4.1 RRU common command set
1) man: See all RRU help command
o
DTR-> man
Command Parameter Help Info.
man - Prints this help list.
init9516 - Initializes Ad9516.
init6655 - Initializes Ad6655.
init9788 - Initializes Ad9788.
Parameter description:
On the left show the Run command on the right shows the role of the command
description
DTR-> drst
3) hr: Show RRU power running track, can be judged RRU unusual in that
DTR-> dcfg
byNum = 4
Parameter Description
5. Troubleshooting
5.1 Silent investigation methods
1) Check the silent TRX binding of BP board:
telnet to the CC type the following command:
a) ShowPrm: View BP board configuration
b) ShowTrxInBp
byBPIndex view the configuration of the BP board binding of TRX, TRX
can be found in the silent which BP bound to the plate, while carrying through
bIPTBSetupFlag positioning silent TRX is created, a creation, 0 did not create, if not
to create a certain quiet, need to find CC's PRM investigation.
Length
4
5
>=6
Level
M
M
O
Meaning
PKG_HEAD : 10 80 00 03 5A 54 45 0B
MSG_HEAD : 7D 00 FF FF FF
RtpPort attribute : 7A 01 01 01 40 08
Field
Meaning
Length
Attribute 1
0x7a
Id
TrxNum 1
Configure the number of carrier frequency
TrxPort 4
Carrier frequency of a port resources (the carrier frequency is
1
allocated for each of four consecutive ports, one for CS
operations RTP / RTCP, PS business, RTP / RTCP. The port resources
for the four consecutive ports of the first port number.)
TrxPort 4
Port resources, carrier frequency 2
2
... ....
TrxPort 4
Carrier frequency of n-port resources
N
port (port number): see corresponding data load of the upper and
Rnc to Bpc ETH CDESCs Statistics: iBSC to the BTS downlink data reception
Bpc to Rnc ETH CDESCs Statistics: BTS uplink data reception to iBSC
2 times as long as the continuous input of the command, whether the changes observed
packets can locate the specific problem is upstream or downstream silent.
o
o
ShowStateInfo 1, Cell, Trx query GSPS records FU and the logic state of each TS;
DbsShowTableRecord
5 (table number), 0 (bIsDbEx) View platform database BP
veneer state, the specific parameter description, see CC command query.
2) investigation RRU
o