Академический Документы
Профессиональный Документы
Культура Документы
01
Date
2013-04-28
Notice
The purchased products, services and features are stipulated by the contract made between Huawei and the
customer. All or part of the products, services and features described in this document may not be within the
purchase scope or the usage scope. Unless otherwise specified in the contract, all statements, information,
and recommendations in this document are provided "AS IS" without warranties, guarantees or representations
of any kind, either express or implied.
The information in this document is subject to change without notice. Every effort has been made in the
preparation of this document to ensure accuracy of the contents, but all statements, information, and
recommendations in this document do not constitute a warranty of any kind, express or implied.
Website:
http://www.huawei.com
Email:
support@huawei.com
Issue 01 (2013-04-28)
SingleRAN
Common Clock Feature Parameter Description
Contents
Contents
1 About This Document..................................................................................................................1
1.1 Scope..............................................................................................................................................................................1
1.2 Intended Audience..........................................................................................................................................................2
1.3 Change History...............................................................................................................................................................2
1.4 Differences Between Base Station Types.......................................................................................................................2
2 Overview.........................................................................................................................................3
3 Common GPS/BITS Reference Clock........................................................................................5
3.1 Common GPS/BITS Reference Clock in Separate-MPT Multimode Base Stations......................................................6
3.2 Common GPS/BITS Reference Clock in Co-MPT Multimode Base Stations...............................................................7
3.3 Common GPS/BITS Reference Clock in Hybrid-MPT Multimode Base Stations........................................................8
8 Engineering Guidelines.............................................................................................................36
8.1 When to Use Common Clock.......................................................................................................................................36
8.2 Required Information...................................................................................................................................................36
8.3 Requirements................................................................................................................................................................36
8.4 Initial Configuration.....................................................................................................................................................38
Issue 01 (2013-04-28)
ii
SingleRAN
Common Clock Feature Parameter Description
Contents
9 Parameters.....................................................................................................................................64
10 Counters......................................................................................................................................79
11 Glossary.......................................................................................................................................80
12 Reference Documents...............................................................................................................81
Issue 01 (2013-04-28)
iii
SingleRAN
Common Clock Feature Parameter Description
1.1 Scope
This document describes the Common Clock feature, which applies to multimode base stations
(MBTSs). Common clocks in multimode base stations can be classified into:
l
For details about clock configuration of a single-mode base station, see Synchronization Feature
Parameter Description for this mode.
The Common Clock feature involves the following features:
l
l Before reading this document, familiarize yourself with Synchronization Feature Parameter
Description for each mode, including eRAN, RAN, and GBSS.
l GBTS refers to a base station deployed with GTMU.
l eGBTS refers to a base station deployed with UMPT_G.
l NodeB refers to a base station deployed with WMPT or UMPT_U.
l eNodeB refers to a base station deployed with LMPT or UMPT_L.
l Co-MPT multimode base station refers to a base station deployed with UMPT_GU, UMPT_GL,
UMPT_UL, or UMPT_GUL, and it functionally corresponds to any combination of eGBTS, NodeB,
and eNodeB. For example, Co-MPT multimode base station deployed with UMPT_GU functionally
corresponds to the combination of eGBTS and NodeB.
l Separate-MPT multimode base station refers to a base station on which different modes use different
main control boards. For example, base stations deployed with GTMU and WMPT are called separateMPT GSM/UMTS dual-mode base station.
Issue 01 (2013-04-28)
SingleRAN
Common Clock Feature Parameter Description
Feature change
Changes in features of a specific product version
Editorial change
Changes in wording or addition of information that was not described in the earlier version
SRAN8.0 01 (2013-04-28)
This issue does not include any changes.
Added common reference clock solutions for co-MPT GSM/UMTS, GSM/LTE, UMTS/
LTE, and GSM/UMTS/LTE multimode base stations.
Added common reference clock solutions for separate-MPT multimode base stations and
co-MPT multimode base stations.
Issue 01 (2013-04-28)
SingleRAN
Common Clock Feature Parameter Description
2 Overview
Overview
With the Common Clock feature, all modes of a multimode base station share a clock source
and requires only one set of clock equipment.
The Common Clock feature applies to GSM/UMTS, GSM/LTE, or UMTS/LTE dual-mode and
GSM/UMTS/LTE triple-mode base stations. The Common Clock feature helps reduce operating
expense (OPEX) and capital expenditure (CAPEX).
A multimode base station can be configured with the following common reference clocks:
l
Separate-MPT scenario: Separate-MPT main controls boards are used in GSM, UMTS,
and LTE modes.
If all modes in a multimode base station are configured in the same BBU, all modes
exchange data by using the BBU backplane and share a clock source. If the modes of a
multimode base station are configured in two different BBUs, the BBU Interconnection
feature must be enabled.
The following restrictions apply to this scenario:
The shared clock source supports only frequency synchronization.
A multimode base station does not support the AUTO(Auto Handover) clock working
mode. Each mode in a multimode base station can be configured with only one clock
source. The main control board in each mode can be configured with only one reference
clock.
A multimode base station can be configured with only one USCU board and the USCU
board can be configured with only one clock source. A USCU board must be configured
for the GBTS, eGBTS, NodeB, or eNodeB if these base stations need to obtain a
Issue 01 (2013-04-28)
SingleRAN
Common Clock Feature Parameter Description
2 Overview
reference clock from the USCU board. The USCU boards of these base stations must
be configured with the same clock source.
In the inter-subrack SDR scenario, time synchronization between modes in different
subracks is not supported.
l
Co-MPT scenario: The GBTS/eGBTS, NodeB, and eNodeB share a UMPT board.
The UMPT board provides the reference clock for each mode and supports the Common
Clock feature. The reference clock provided by the UMPT board supports frequency
synchronization and time synchronization.
NOTE
l The UMPT board can be configured for a single-mode base station. UMPT_G, UMPT_U, and
UMPT_L represent the UMPT board configured for GSM, UMTS, and LTE single-mode base stations,
respectively.
l The UMPT board can be configured for a dual-mode or triple-mode base station. UMPT_GU,
UMPT_GL, UMPT_UL, and UMPT_GUL represent the UMPT board configured for GSM/UMTS,
GSM/LTE, UMTS/LTE, and GSM/UMTS/LTE multimode base stations, respectively.
Issue 01 (2013-04-28)
SingleRAN
Common Clock Feature Parameter Description
This chapter describes the common GPS/BITS reference clock in separate-MPT, co-MPT, and
hybrid-MPT multimode base stations.
Issue 01 (2013-04-28)
SingleRAN
Common Clock Feature Parameter Description
Figure 3-2 A common GPS/BITS reference clock in a separate-MPT GSM/LTE dual-mode base
station
Issue 01 (2013-04-28)
SingleRAN
Common Clock Feature Parameter Description
Issue 01 (2013-04-28)
SingleRAN
Common Clock Feature Parameter Description
When BBU Interconnection is enabled, the GPS/BITS reference clock is shared as follows:
l
As shown in Figure 3-6, the USCU board is installed in the primary BBU of a GSM/UMTS/
LTE triple-mode base station. The USCU board receives GPS or BITS clock signals and
forwards them to the GTMU and LMPT boards. Upon receiving the clock signals, the
GTMU board forwards them to the UCIU board. This UCIU board then sends the clock
signals to the UMPT board in the secondary BBU, which receives them through its BBU
interconnection port.
As shown in Figure 3-7, the USCU board is installed in the secondary BBU of a GSM/
UMTS/LTE triple-mode base station. The USCU board receives GPS or BITS clock signals
Issue 01 (2013-04-28)
SingleRAN
Common Clock Feature Parameter Description
and forwards them to the UMPT board, which in turn sends them through its BBU
interconnect port to the UCIU board in the primary BBU. This UCIU board then sends the
clock signals to the GTMU and LMPT boards by using the BBU backplane.
Figure 3-6 A common GPS/BITS reference clock in the primary BBU of a GSM/UMTS/
LTE triple-mode base station
Figure 3-7 A common GPS/BITS reference clock in the secondary BBU of a GSM/UMTS/LTE
triple-mode base station
Issue 01 (2013-04-28)
SingleRAN
Common Clock Feature Parameter Description
This chapter describes the common E1/T1 reference clock in separate-MPT, co-MPT, and
hybrid-MPT multimode base stations.
Table 4-1 describes the typical application scenarios for a common E1/T1 reference clock.
Table 4-1 Typical application scenarios for a common E1/T1 reference clock
Deployment Scenario
Description
NOTE
Only the UMTS mode can obtain E1/T1 clock signals from a UTRP board.
The LTE mode can obtain E1/T1 clock signals from a UMPT board.
For details about the Common Transmission feature, see Common Transmission Feature
Parameter Description for SingleRAN.
Issue 01 (2013-04-28)
10
SingleRAN
Common Clock Feature Parameter Description
Issue 01 (2013-04-28)
11
SingleRAN
Common Clock Feature Parameter Description
Figure 4-2 A common E1/T1 reference clock in a separate-MPT GSM/LTE dual-mode base
station
Figure 4-3 A common E1/T1 reference clock in a separate-MPT UMTS/LTE dual-mode base
station
12
SingleRAN
Common Clock Feature Parameter Description
Figure 4-4 A common E1/T1 reference clock in a co-MPT GSM/UMTS/LTE triple-mode base
station
Issue 01 (2013-04-28)
13
SingleRAN
Common Clock Feature Parameter Description
14
SingleRAN
Common Clock Feature Parameter Description
As shown in Figure 4-6 , the common E1/T1 reference clock is in the primary BBU of a
GSM/UMTS/LTE triple-mode base station. The GTMU board receives E1/T1 clock signals
from the transport network over an E1/T1 link and forwards them to the LMPT and UCIU
boards. Upon receiving the clock signals, the UCIU board sends them to the UMPT board
in the secondary BBU, which receives them over the BBU interconnection port.
As shown in Figure 4-7, the common E1/T1 reference clock is in the secondary BBU of a
GSM/UMTS/LTE triple-mode base station. The UMPT board receives E1/T1 clock signals
from the transport network over an E1/T1 link and forwards them to the UCIU board in the
primary BBU. Upon receiving the clock signals, the UCIU board sends them to the GTMU
and LMPT boards by using the BBU backplane.
Figure 4-6 A common E1/T1 reference clock in the primary BBU of a GSM/UMTS/LTE
triple-mode base station
Issue 01 (2013-04-28)
15
SingleRAN
Common Clock Feature Parameter Description
Figure 4-7 A common E1/T1 reference clock in the secondary BBU of a GSM/UMTS/LTE
triple-mode base station
Issue 01 (2013-04-28)
16
SingleRAN
Common Clock Feature Parameter Description
This chapter describes the common IEEE 1588v2 reference clock in separate-MPT, co-MPT,
and hybrid-MPT multimode base stations.
Table 5-1 describes the typical application scenarios for a common IEEE 1588v2 reference
clock.
Table 5-1 Typical application scenarios for a common IEEE 1588v2 reference clock
Deployment Scenario
Description
Issue 01 (2013-04-28)
17
SingleRAN
Common Clock Feature Parameter Description
Issue 01 (2013-04-28)
Deployment Scenario
Description
18
SingleRAN
Common Clock Feature Parameter Description
Issue 01 (2013-04-28)
19
SingleRAN
Common Clock Feature Parameter Description
Figure 5-2 A common IEEE 1588v2 reference clock in a separate-MPT GSM/LTE dual-mode
base station
Figure 5-3 A common IEEE 1588v2 reference clock in a separate-MPT UMTS/LTE dual-mode
base station
Issue 01 (2013-04-28)
20
SingleRAN
Common Clock Feature Parameter Description
Issue 01 (2013-04-28)
21
SingleRAN
Common Clock Feature Parameter Description
Figure 5-5 A common IEEE 1588v2 reference clock in a hybrid-MPT GSM/UMTS/LTE triplemode base station
Issue 01 (2013-04-28)
22
SingleRAN
Common Clock Feature Parameter Description
As shown in Figure 5-6, the common IEEE 1588v2 reference clock is in the primary BBU
of a GSM/UMTS/LTE triple-mode base station. The LMPT board is configured with an
IEEE 1588v2 clock client and receives IEEE 1588v2 clock packets containing clock signals
from an IEEE 1588v2 clock server through the transport network. Then, the LMPT board
generates synchronized 1 PPS clock signals and forwards them to the GTMU and UCIU
boards. Upon receiving the synchronized 1 PPS clock signals, the UCIU board sends them
to the UMPT board in the secondary BBU. Base stations of other modes in the primary
BBU obtain 1 PPS clock signals by using the BBU backplane.
As shown in Figure 5-7, the common IEEE 1588v2 reference clock is in the secondary
BBU of a GSM/UMTS/LTE triple-mode base station. The UMPT board is configured with
an IEEE 1588v2 clock client and receives IEEE 1588v2 clock packets containing clock
signals from an IEEE 1588v2 clock server through the transport network. Then, the UMPT
board generates synchronized 1 PPS clock signals and forwards them to the UCIU board
in the primary BBU, which in turn forwards them to the GTMU and WMPT boards.
Transmission port cabling on a multimode base station and the cabling of a common IEEE
1588v2 reference clock are independently deployed. Therefore, the operation of the multimode
base station is not affected.
Figure 5-6 A common IEEE 1588v2 reference clock in the primary BBU of a GSM/UMTS/
LTE triple-mode base station
Issue 01 (2013-04-28)
23
SingleRAN
Common Clock Feature Parameter Description
Figure 5-7 A common IEEE 1588v2 reference clock in the secondary BBU of a GSM/UMTS/
LTE triple-mode base station
Issue 01 (2013-04-28)
24
SingleRAN
Common Clock Feature Parameter Description
Issue 01 (2013-04-28)
Deployment Scenario
Description
25
SingleRAN
Common Clock Feature Parameter Description
Deployment Scenario
Description
Issue 01 (2013-04-28)
26
SingleRAN
Common Clock Feature Parameter Description
Issue 01 (2013-04-28)
27
SingleRAN
Common Clock Feature Parameter Description
Figure 6-2 A common synchronous Ethernet reference clock in a separate-MPT GSM/LTE dualmode base station
Issue 01 (2013-04-28)
28
SingleRAN
Common Clock Feature Parameter Description
6.2 Common Synchronous Ethernet Reference Clock in CoMPT Multimode Base Stations
As shown in Figure 6-4, each mode uses the synchronous Ethernet clock source configured for
the UMPT board. The UMPT board supports the Common Clock feature.
Figure 6-4 A common synchronous Ethernet reference clock in a co-MPT GSM/UMTS/LTE
triple-mode base station
Issue 01 (2013-04-28)
29
SingleRAN
Common Clock Feature Parameter Description
Issue 01 (2013-04-28)
30
SingleRAN
Common Clock Feature Parameter Description
As shown in Figure 6-6, the common synchronous Ethernet reference clock in the primary
BBU of a GSM/UMTS/LTE triple-mode base station. The WMPT board receives
synchronous Ethernet clock signals from the transport network over an FE link and
forwards them to the GTMU and UCIU boards. Upon receiving the clock signals, the UCIU
board sends them to the UMPT board in the secondary BBU. The other mode of base station
in the primary BBU obtains synchronous Ethernet clock signals by using the BBU
backplane.
As shown in Figure 6-7, the common synchronous Ethernet reference clock in the
secondary BBU of a GSM/UMTS/LTE triple-mode base station. The UMPT board receives
synchronous Ethernet clock signals from the transport network over a GE link and forwards
them to the UCIU board in the primary BBU. Upon receiving the clock signals, the UCIU
board sends them to the GTMU and WMPT boards.
Figure 6-6 A common synchronous Ethernet reference clock in the primary BBU of a
GSM/UMTS/LTE triple-mode base station
Issue 01 (2013-04-28)
31
SingleRAN
Common Clock Feature Parameter Description
Figure 6-7 A common synchronous Ethernet reference clock in the secondary BBU of a GSM/
UMTS/LTE triple-mode base station
Issue 01 (2013-04-28)
32
SingleRAN
Common Clock Feature Parameter Description
When the GSM, UMTS, and LTE modes share a UMTS board, besides common GPS, BITS,
E1/T1, IEEE 1588v2, and synchronous Ethernet reference clocks, the following common
reference clocks can be used:
l
These two common reference clocks are used only when the GSM, UMTS, and LTE modes
share a UMPT board. This is because these two common reference clocks only support a single
mode in a separate-MPT multimode base station.
Issue 01 (2013-04-28)
33
SingleRAN
Common Clock Feature Parameter Description
7.2 Common IEEE 1588v2+SyncE Reference Clock in CoMPT GSM/UMTS/LTE Triple-mode Base Stations
The IEEE 1588v2+SyncE clock source combines the IEEE 1588v2 clock and synchronous
Ethernet clock and supports only time synchronization. The clock source of the IEEE 1588v2
clock server must be the same as that of the synchronous Ethernet. As shown in Figure 7-2, the
UMPT board is configured with the IEEE 1588v2+SyncE clock source, which is shared by the
GSM, UMTS, and LTE modes. The clock source of the IEEE 1588v2 clock server and the
synchronous Ethernet in Figure 7-2 are GPS.
Issue 01 (2013-04-28)
34
SingleRAN
Common Clock Feature Parameter Description
Figure 7-2 A common IEEE 1588v2+SyncE reference clock in a co-MPT GSM/UMTS/LTE triple-mode base station
Issue 01 (2013-04-28)
35
SingleRAN
Common Clock Feature Parameter Description
8 Engineering Guidelines
Engineering Guidelines
Whether the multimode base station is configured with a GPS antenna or can obtain clock
signals from a BITS clock source
If the multimode base station is configured with a GPS antenna or can obtain clock signals
from a BITS clock source, it is recommended that two modes of the base station share a
GPS or BITS reference clock.
8.3 Requirements
MRFD-211601 Multi-mode BS Common Reference Clock(GBTS/eGBTS) and MRFD-221601
Multi-mode BS Common Reference Clock(NodeB) are not under license control.
MRFD-231601 Multi-mode BS Common Reference Clock(eNodeB) is under license control.
Issue 01 (2013-04-28)
36
SingleRAN
Common Clock Feature Parameter Description
8 Engineering Guidelines
Feature ID
Feature Name
License
Control Item
NE
Sales Unit
MRFD-231601
Multi-mode BS
Common
Reference
Clock(eNodeB)
Function-LTELLT1MCRC01
Common Clock
(eNodeB) (per
eNodeB)
eNodeB
per eNodeB
Hardware
l
If a GPS or BITS reference clock is used, a USCU board must be installed in the BBU.
Other Features
l
Issue 01 (2013-04-28)
37
SingleRAN
Common Clock Feature Parameter Description
8 Engineering Guidelines
Configuring a Common IEEE 1588v2 Reference Clock on the GBTS or eGBTS Side
Issue 01 (2013-04-28)
Parameter Name
MML Parameter
ID
Parameter Name
on the CME
Setting Notes
System clock
working mode
MODE
System Clock
Working Mode
38
SingleRAN
Common Clock Feature Parameter Description
8 Engineering Guidelines
Parameter Name
MML Parameter
ID
Parameter Name
on the CME
Setting Notes
Selected Clock
Source
CLKSRC
----End
MML Parameter
ID
Parameter Name
on the CME
Setting Notes
System clock
working mode
MODE
System Clock
Working Mode
Selected Clock
Source
CLKSRC
----End
39
SingleRAN
Common Clock Feature Parameter Description
8 Engineering Guidelines
Parameter Name
MML Parameter
ID
Parameter Name
on the CME
Setting Notes
System clock
working mode
MODE
System Clock
Working Mode
Selected Clock
Source
CLKSRC
----End
Configuring a Common IEEE 1588v2 Reference Clock on the GBTS or eGBTS Side
To configure a common IEEE 1588v2 reference clock for the GBTS, perform the following
steps:
Step 1 Run the SET BTSIPCLKPARA command to configure parameters for an IEEE 1588v2 clock
link. Set the key parameters according to the descriptions in the following table.
Issue 01 (2013-04-28)
Parameter Name
MML Parameter
ID
Parameter Name
on the CME
Setting Notes
CLKPRTTYPE
IP Clock Time
Synchronization
Mode
SYNMode
Clock
Synchronization
Mode
Clock Topology
Mode
CLKTOPOMODE
Clock Topology
Mode
Clock Reference
Source Redundancy
ISCLKREDUCY
Clock Reference
Source Redundancy
40
SingleRAN
Common Clock Feature Parameter Description
8 Engineering Guidelines
Parameter Name
MML Parameter
ID
Parameter Name
on the CME
Setting Notes
Clock Server 0 IP
Address
MASTERIPADDR
Clock Server 0 IP
Address
Clock Server 1 IP
Address
SLAVEIPADDR
Clock Server 1 IP
Address
Step 2 Run the SET BTSCLK command with ClkType (the CME name is Clock Type) set to
IP_TIME(IP Clock).
----End
To configure a common IEEE 1588v2 reference clock for the eGBTS, perform the following
steps:
Step 1 Run the ADD IPCLKLINK command to add an IEEE 1588v2 clock link. Set the key parameters
according to the descriptions in the following table.
Parameter Name
MML Parameter
ID
Parameter Name
on the CME
Setting Notes
Protocol Type
ICPT
Protocol Type
Profile Type
PROFILETYPE
Profile Type
Slot No.
Issue 01 (2013-04-28)
SN
Slot No.
41
SingleRAN
Common Clock Feature Parameter Description
8 Engineering Guidelines
Parameter Name
MML Parameter
ID
Parameter Name
on the CME
Setting Notes
Clock Topology
Mode
CNM
Client IP
CIP
Client IPv4
Server IP
SIP
Server IPv4
NOTE
If the IEEE 1588v2 clock server and the eGBTS are on different network segments, run the ADD IPRT
command to configure the route between the IEEE 1588v2 clock server and the eGBTS.
Step 2 Run the SET CLKMODE command to activate the IEEE 1588v2 reference clock. Set the key
parameters according to the descriptions in the following table.
Parameter Name
MML Parameter
ID
Parameter Name
on the CME
Setting Notes
System clock
working mode
MODE
Clock Working
Mode
Selected Clock
Source
CLKSRC
Selected Clock
Source
IP Clock Time
Synchronization
Mode
SYNMODE
Synchronization
Mode
----End
Issue 01 (2013-04-28)
42
SingleRAN
Common Clock Feature Parameter Description
8 Engineering Guidelines
MML Parameter
ID
Parameter Name
on the CME
Setting Notes
Slot No.
SN
Slot No.
Port No.
PN
Port No.
To configure a common synchronous Ethernet reference clock for the eGBTS, perform the
following steps:
Step 1 Run the ADD SYNCETH command to add a synchronous Ethernet clock link. Set the key
parameters according to the descriptions in the following table.
Issue 01 (2013-04-28)
Parameter Name
MML Parameter
ID
Parameter Name
on the CME
Setting Notes
Slot No.
SN
Slot No.
Port No.
PN
Port No.
43
SingleRAN
Common Clock Feature Parameter Description
8 Engineering Guidelines
Parameter Name
MML Parameter
ID
Parameter Name
on the CME
Setting Notes
SSM Selection
SSM
Synchronization
Status Message
Step 2 Run the SET CLKMODE command to activate the synchronous Ethernet reference clock. Set
the key parameters according to the descriptions in the following table.
Parameter Name
MML Parameter
ID
Parameter Name
on the CME
Setting Notes
System clock
working mode
MODE
Clock Working
Mode
Selected Clock
Source
CLKSRC
Selected Clock
Source
----End
MML Parameter
ID
Parameter Name
on the CME
Setting Notes
System clock
working mode
MODE
Clock Working
Mode
Selected Clock
Source
CLKSRC
Selected Clock
Source
----End
44
SingleRAN
Common Clock Feature Parameter Description
8 Engineering Guidelines
MML Parameter
ID
Parameter Name
on the CME
Setting Notes
System clock
working mode
MODE
System Clock
Working Mode
Selected Clock
Source
CLKSRC
----End
MML Parameter
ID
Parameter Name
on the CME
Setting Notes
System clock
working mode
MODE
System Clock
Working Mode
Selected Clock
Source
CLKSRC
----End
Issue 01 (2013-04-28)
45
SingleRAN
Common Clock Feature Parameter Description
8 Engineering Guidelines
MML Parameter
ID
Parameter Name
on the CME
Setting Notes
System clock
working mode
MODE
System Clock
Working Mode
Selected Clock
Source
CLKSRC
----End
MML
Parameter ID
Paramete
r Name
on the
CME
Setting Notes
Protocol
Type
ICPT
Protocol
Type
Profile
Type
PROFILETYP
E
Profile
Type
Issue 01 (2013-04-28)
Slot No.
SN
Slot No.
Clock
Topology
Mode
CNM
Clock Net
Mode
46
SingleRAN
Common Clock Feature Parameter Description
8 Engineering Guidelines
Paramete
r Name
MML
Parameter ID
Paramete
r Name
on the
CME
Setting Notes
Client IP
CIP
Client
IPv4
Server IP
SIP
Server
IPv4
NOTE
If the IEEE 1588v2 clock server and the NodeB are on different network segments, run the ADD IPRT
command to configure the route between the IEEE 1588v2 clock server and the NodeB.
The NodeB does not support IPV6.
Step 2 Run the SET CLKMODE command to activate the IEEE 1588v2 reference clock. Set the key
parameters according to the descriptions in the following table.
Parameter Name
MML Parameter
ID
Parameter Name
on the CME
Setting Notes
System clock
working mode
MODE
Clock Working
Mode
Selected Clock
Source
CLKSRC
Selected Clock
Source
IP Clock Time
Synchronization
Mode
SYNMODE
Synchronization
Mode
----End
Issue 01 (2013-04-28)
47
SingleRAN
Common Clock Feature Parameter Description
8 Engineering Guidelines
Parameter Name
MML Parameter
ID
Parameter Name
on the CME
Setting Notes
Slot No.
SN
Slot No.
Port No.
PN
Port No.
SSM Selection
SSM
Synchronization
Status Message
Step 2 Run the SET CLKMODE command to activate the synchronous Ethernet reference clock. Set
the key parameters according to the descriptions in the following table.
Parameter Name
MML Parameter
ID
Parameter Name
on the CME
Setting Notes
System clock
working mode
MODE
Clock Working
Mode
Selected Clock
Source
CLKSRC
Selected Clock
Source
----End
Issue 01 (2013-04-28)
48
SingleRAN
Common Clock Feature Parameter Description
8 Engineering Guidelines
Parameter Name
MML Parameter
ID
Parameter Name
on the CME
Setting Notes
System clock
working mode
MODE
Clock Working
Mode
Selected Clock
Source
CLKSRC
Selected Clock
Source
----End
MML Parameter
ID
Parameter Name
on the CME
Setting Notes
System clock
working mode
MODE
System Clock
Working Mode
Selected Clock
Source
CLKSRC
----End
Issue 01 (2013-04-28)
49
SingleRAN
Common Clock Feature Parameter Description
8 Engineering Guidelines
NOTE
The eNodeB does not support switch between clock sources. Therefore, the System clock working
mode parameter must be set to MANUAL(Manual Handover).
MML Parameter
ID
Parameter Name
on the CME
Setting Notes
System clock
working mode
MODE
System Clock
Working Mode
Selected Clock
Source
CLKSRC
----End
MML Parameter
ID
Parameter Name
on the CME
Setting Notes
System clock
working mode
MODE
System Clock
Working Mode
Selected Clock
Source
CLKSRC
----End
Issue 01 (2013-04-28)
50
SingleRAN
Common Clock Feature Parameter Description
8 Engineering Guidelines
MML Parameter
ID
Parameter Name
on the CME
Setting Notes
Protocol Type
ICPT
Protocol Type
Profile Type
PROFILETYPE
Profile Type
Issue 01 (2013-04-28)
Slot No.
SN
Slot No.
Clock Topology
Mode
CNM
Client IP
CIP
Client IPv4
Server IP
SIP
Server IPv4
51
SingleRAN
Common Clock Feature Parameter Description
8 Engineering Guidelines
Parameter Name
MML Parameter
ID
Parameter Name
on the CME
Setting Notes
Client IPv6
CIPV6
Client IPv6
Server IPv6
SIPV6
Server IPv6
NOTE
If the IEEE 1588v2 clock server and the eNodeB are on different network segments, run the ADD IPRT
command to configure the route between the IEEE 1588v2 clock server and the eNodeB.
Step 2 Run the SET CLKMODE command to activate the IEEE 1588v2 reference clock. Set the key
parameters according to the descriptions in the following table.
Parameter Name
MML Parameter
ID
Parameter Name
on the CME
Setting Notes
System clock
working mode
MODE
Clock Working
Mode
Selected Clock
Source
CLKSRC
Selected Clock
Source
IP Clock Time
Synchronization
Mode
SYNMODE
Synchronization
Mode
----End
Issue 01 (2013-04-28)
52
SingleRAN
Common Clock Feature Parameter Description
8 Engineering Guidelines
Parameter Name
MML Parameter
ID
Parameter Name
on the CME
Setting Notes
Slot No.
SN
Slot No.
Port No.
PN
Port No.
SSM Selection
SSM
Synchronization
Status Message
Step 2 Run the SET CLKMODE command to activate the synchronous Ethernet reference clock. Set
the key parameters according to the descriptions in the following table.
Parameter Name
MML Parameter
ID
Parameter Name
on the CME
Setting Notes
System clock
working mode
MODE
Clock Working
Mode
Selected Clock
Source
CLKSRC
Selected Clock
Source
----End
53
SingleRAN
Common Clock Feature Parameter Description
8 Engineering Guidelines
Parameter Name
MML Parameter
ID
Parameter Name
on the CME
Setting Notes
System clock
working mode
MODE
Clock Working
Mode
Selected Clock
Source
CLKSRC
Selected Clock
Source
----End
Configuring a Common GPS Reference Clock on the Co-MPT Base Station Side
Configuring a Common BITS Reference Clock on the Co-MPT Base Station Side
Configuring a Common E1/T1 Reference Clock on the Co-MPT Base Station Side
Configuring a Common IEEE 1588v2 Reference Clock on the Co-MPT Base Station
Side
Configuring a Common GPS Reference Clock on the Co-MPT Base Station Side
Before configuring a common GPS reference clock, ensure that the co-MPT multimode base
station has been configured with a USCU board.
Step 1 Run the ADD GPS command to add a GPS clock link.
Step 2 Run the SET CLKMODE command to activate the GPS reference clock. Set the key parameters
according to the descriptions in the following table.
Issue 01 (2013-04-28)
Parameter Name
MML Parameter
ID
Parameter Name
on the CME
Setting Notes
System clock
working mode
MODE
System Clock
Working Mode
54
SingleRAN
Common Clock Feature Parameter Description
8 Engineering Guidelines
Parameter Name
MML Parameter
ID
Parameter Name
on the CME
Setting Notes
Selected Clock
Source
CLKSRC
----End
Configuring a Common BITS Reference Clock on the Co-MPT Base Station Side
Before configuring a common BITS reference clock, ensure that the co-MPT multimode base
station has been configured with a USCU board.
Step 1 Run the ADD BITS command to add a BITS clock link.
Step 2 Run the SET CLKMODE command to activate the BITS reference clock. Set the key
parameters according to the descriptions in the following table.
Parameter Name
MML Parameter
ID
Parameter Name
on the CME
Setting Notes
System clock
working mode
MODE
System Clock
Working Mode
Selected Clock
Source
CLKSRC
----End
Configuring a Common E1/T1 Reference Clock on the Co-MPT Base Station Side
Before configuring a common E1/T1 reference clock, ensure that an E1/T1 clock link is
available.
Step 1 Run the ADD LINECLK command to add an E1/T1 clock link. In this step, set Port Type
(Port Type on the CME) to E1T1(E1T1).
Step 2 Run the SET CLKMODE command to activate the E1/T1 reference clock. Set the key
parameters according to the descriptions in the following table.
Issue 01 (2013-04-28)
Parameter Name
MML Parameter
ID
Parameter Name
on the CME
Setting Notes
System clock
working mode
MODE
System Clock
Working Mode
Selected Clock
Source
CLKSRC
55
SingleRAN
Common Clock Feature Parameter Description
8 Engineering Guidelines
----End
Configuring a Common IEEE 1588v2 Reference Clock on the Co-MPT Base Station
Side
Step 1 Run the ADD IPCLKLINK command to add an IEEE 1588v2 clock link. Set the key parameters
according to the descriptions in the following table.
Parameter Name
MML Parameter
ID
Parameter Name
on the CME
Setting Notes
Protocol Type
ICPT
Protocol Type
Profile Type
PROFILETYPE
Profile Type
Issue 01 (2013-04-28)
Slot No.
SN
Slot No.
Clock Topology
Mode
CNM
Client IP
CIP
Client IPv4
56
SingleRAN
Common Clock Feature Parameter Description
8 Engineering Guidelines
Parameter Name
MML Parameter
ID
Parameter Name
on the CME
Setting Notes
Server IP
SIP
Server IPv4
Client IPv6
CIPV6
Client IPv6
Server IPv6
SIPV6
Server IPv6
NOTE
If the IEEE 1588v2 clock server and the co-MPT multimode base station are on different network segments,
run the ADD IPRT command to configure the route between the IEEE 1588v2 clock server and the coMPT multimode base station.
Step 2 Run the SET CLKMODE command to activate the IEEE 1588v2 reference clock. Set the key
parameters according to the descriptions in the following table.
Parameter Name
MML Parameter
ID
Parameter Name
on the CME
Setting Notes
System clock
working mode
MODE
Clock Working
Mode
Selected Clock
Source
CLKSRC
Selected Clock
Source
IP Clock Time
Synchronization
Mode
SYNMODE
Synchronization
Mode
----End
57
SingleRAN
Common Clock Feature Parameter Description
8 Engineering Guidelines
Step 1 Run the ADD SYNCETH command to add a synchronous Ethernet clock link. Set the key
parameters according to the descriptions in the following table.
Parameter Name
MML Parameter
ID
Parameter Name
on the CME
Setting Notes
Slot No.
SN
Slot No.
Port No.
PN
Port No.
SSM Selection
SSM
Synchronization
Status Message
Step 2 Run the SET CLKMODE command to activate the synchronous Ethernet reference clock. Set
the key parameters according to the descriptions in the following table.
Parameter Name
MML Parameter
ID
Parameter Name
on the CME
Setting Notes
System clock
working mode
MODE
Clock Working
Mode
Selected Clock
Source
CLKSRC
Selected Clock
Source
----End
58
SingleRAN
Common Clock Feature Parameter Description
8 Engineering Guidelines
Parameter Name
MML Parameter
ID
Parameter Name
on the CME
Setting Notes
System clock
working mode
MODE
Clock Working
Mode
Selected Clock
Source
CLKSRC
Selected Clock
Source
----End
MML Parameter
ID
Parameter Name
on the CME
Setting Notes
System clock
working mode
MODE
System Clock
Working Mode
Selected Clock
Source
CLKSRC
----End
Issue 01 (2013-04-28)
59
SingleRAN
Common Clock Feature Parameter Description
8 Engineering Guidelines
Parameter Name
MML Parameter
ID
Parameter Name
on the CME
Setting Notes
Slot No.
SN
Slot No.
Port No.
PN
Port No.
SSM Selection
SSM
Synchronization
Status Message
LN
Link No. 0 is
synchronousEthernet input and
link No. 1 is
synchronousEthernet output.
Step 2 Run the ADD IPCLKLINK command to add an IEEE 1588v2 clock link. Set the key parameters
according to the descriptions in the following table.
Issue 01 (2013-04-28)
Parameter Name
MML Parameter
ID
Parameter Name
on the CME
Setting Notes
Protocol Type
ICPT
Protocol Type
60
SingleRAN
Common Clock Feature Parameter Description
8 Engineering Guidelines
Parameter Name
MML Parameter
ID
Parameter Name
on the CME
Setting Notes
Profile Type
PROFILETYPE
Profile Type
Issue 01 (2013-04-28)
Slot No.
SN
Slot No.
Clock Topology
Mode
CNM
Client IP
CIP
Client IPv4
Server IP
SIP
Server IPv4
Client IPv6
CIPV6
Client IPv6
Server IPv6
SIPV6
Server IPv6
61
SingleRAN
Common Clock Feature Parameter Description
8 Engineering Guidelines
NOTE
If the IEEE 1588v2 clock server and the co-MPT multimode base station are on different network segments,
run the ADD IPRT command to configure the route between the IEEE 1588v2 clock server and the coMPT multimode base station.
Step 3 Run the SET CLKMODE command to activate the IEEE 1588v2+SyncE reference clock. Set
the key parameters according to the descriptions in the following table.
Parameter Name
MML Parameter
ID
Parameter Name
on the CME
Setting Notes
System clock
working mode
MODE
Clock Working
Mode
Selected Clock
Source
CLKSRC
Selected Clock
Source
IP Clock Time
Synchronization
Mode
SYNMODE
Synchronization
Mode
----End
Then...
Issue 01 (2013-04-28)
62
SingleRAN
Common Clock Feature Parameter Description
8 Engineering Guidelines
If...
Then...
----End
8.6 Troubleshooting
If ALM-26276 Inter-System Site-Level Configuration Conflict is generated, a clock reference
type configuration conflict occurs. That is, the base station of the current mode does not support
this type of reference clock. If this occurs, you must check the configuration file and correct the
clock reference type.
Alarm ID
Alarm Name
Configuration Item
26276
Inter-System Site-Level
Configuration Conflict
If the common reference clock is correctly configured but the base station cannot lock the clock
source within 30 minutes after it starts, you need to troubleshoot the common reference clock
fault. For details, see section "Troubleshooting" in Synchronization Feature Parameter
Description for GSM, UMTS, or LTE.
Issue 01 (2013-04-28)
63
SingleRAN
Common Clock Feature Parameter Description
9 Parameters
Parameters
NE
MML
Command
Feature ID
Feature Name
Description
MODE
BTS3900
SET
CLKMODE
MRFD-210501
BTS Clock
LBFD-003005
Synchronization
LBFD-0030050
1
LBFD-0030050
2
Clock Source
Switching
Manually or
Automatically
LBFD-0030050
3
Free-running
Mode
LBFD-0030050
4
Synchronization
with GPS
LBFD-0030050
5
Synchronization
with BITS
LBFD-0030050
6
Synchronization
with 1PPS
LOFD-003013
Synchronization
with E1/T1
Meaning:Indicates the
working mode
of the system
clock. Manual
indicates that a
clock source
must be
specified by the
user. Auto
indicates that the
system
automatically
selects a clock
source based on
the priority and
availability of
the clock source.
Free indicates
that the system
clock works in
free-running
mode, that is, the
system clock
does not trace
any reference
clock source.
DSP CLKSTAT
LST
CLKMODE
LOFD-0030130
1
LOFD-0030130
2
LOFD-0030130
3
LOFD-003023
Enhanced
Synchronization
Synchronization
with Ethernet
(ITU-T G.8261)
IEEE1588 V2
Clock
Synchronization
Clock over IP
(Huawei
proprietary)
Issue 01 (2013-04-28)
GUI Value
Range:AUTO
(Auto),
MANUAL
64
SingleRAN
Common Clock Feature Parameter Description
Parameter ID
NE
MML
Command
9 Parameters
Feature ID
Feature Name
Description
IEEE 1588v2
over IPv6
(Manual), FREE
(Free)
Unit:None
Actual Value
Range:AUTO,
MANUAL,
FREE
Default
Value:FREE
(Free)
Issue 01 (2013-04-28)
65
SingleRAN
Common Clock Feature Parameter Description
9 Parameters
Parameter ID
NE
MML
Command
Feature ID
Feature Name
Description
CLKSRC
BTS3900
SET
CLKMODE
MRFD-210501
BTS Clock
LBFD-003005
Synchronization
LBFD-0030050
1
LBFD-0030050
3
Clock Source
Switching
Manually or
Automatically
LBFD-0030050
4
Synchronization
with GPS
LBFD-0030050
5
Synchronization
with BITS
LBFD-0030050
6
Synchronization
with 1PPS
LOFD-003013
Synchronization
with E1/T1
LST
CLKMODE
LOFD-0030130
1
LOFD-0030130
2
LOFD-0030130
3
LOFD-003023
Enhanced
Synchronization
Synchronization
with Ethernet
(ITU-T G.8261)
IEEE1588 V2
Clock
Synchronization
Clock over IP
(Huawei
proprietary)
IEEE 1588v2
over IPv6
GUI Value
Range:GPS
(GPS Clock),
BITS(BITS
Clock), IPCLK
(IP Clock),
SYNCETH
(SyncEth
Clock),
LINECLK(Line
Clock), TOD
(TOD Clock),
PEERCLK(Peer
Clock),
SYNCETH
+IPCLK
(SyncEth Clock
+IP Clock), GPS
+SYNCETH
(GPS Clock
+SyncEth
Clock)
Unit:None
Actual Value
Range:GPS,
BITS, IPCLK,
SYNCETH,
LINECLK,
TOD,
PEERCLK,
SYNCETH
+IPCLK, GPS
+SYNCETH
Issue 01 (2013-04-28)
66
SingleRAN
Common Clock Feature Parameter Description
Parameter ID
NE
MML
Command
9 Parameters
Feature ID
Feature Name
Description
Default
Value:GPS
(GPS Clock)
Issue 01 (2013-04-28)
67
SingleRAN
Common Clock Feature Parameter Description
9 Parameters
Parameter ID
NE
MML
Command
Feature ID
Feature Name
Description
ICPT
BTS3900
ADD
IPCLKLINK
WRFD-050501
Clock Sync on
Ethernet in
NodeB
LST
IPCLKLINK
GBFD-118606
GBFD-118620
LOFD-0030130
1
LOFD-0030130
2
LOFD-0030130
3
LOFD-003023
Clock over IP
Clock over IP
support 1588v2
Synchronization
with Ethernet
(ITU-T G.8261)
IEEE1588 V2
Clock
Synchronization
Clock over IP
(Huawei
proprietary)
IEEE 1588v2
over IPv6
GUI Value
Range:HW_DE
FINED(HuaWei
Defined
Protocol), PTP
(PTP Protocol)
Unit:None
Actual Value
Range:HW_DE
FINED, PTP
Issue 01 (2013-04-28)
68
SingleRAN
Common Clock Feature Parameter Description
Parameter ID
NE
MML
Command
9 Parameters
Feature ID
Feature Name
Description
Default
Value:PTP(PTP
Protocol)
Issue 01 (2013-04-28)
69
SingleRAN
Common Clock Feature Parameter Description
9 Parameters
Parameter ID
NE
MML
Command
Feature ID
Feature Name
Description
PROFILETYPE
BTS3900
ADD
IPCLKLINK
WRFD-050501
GBFD-118620
Clock Sync on
Ethernet in
NodeB
LOFD-0030130
1
Clock over IP
support 1588v2
LST
IPCLKLINK
LOFD-0030130
2
LOFD-0030130
3
LOFD-003023
Synchronization
with Ethernet
(ITU-T G.8261)
IEEE1588 V2
Clock
Synchronization
Clock over IP
(Huawei
proprietary)
IEEE 1588v2
over IPv6
GUI Value
Range:1588V2
(1588V2), G.
8265.1(G.
8265.1)
Unit:None
Issue 01 (2013-04-28)
70
SingleRAN
Common Clock Feature Parameter Description
Parameter ID
NE
MML
Command
9 Parameters
Feature ID
Feature Name
Description
Actual Value
Range:1588V2,
G.8265.1
Default Value:
1588V2
(1588V2)
SN
BTS3900
ADD
IPCLKLINK
None
None
LST
IPCLKLINK
Issue 01 (2013-04-28)
71
SingleRAN
Common Clock Feature Parameter Description
9 Parameters
Parameter ID
NE
MML
Command
Feature ID
Feature Name
Description
CNM
BTS3900
ADD
IPCLKLINK
WRFD-050501
GBFD-118620
Clock Sync on
Ethernet in
NodeB
LOFD-0030130
1
Clock over IP
support 1588v2
Meaning:Indicates the
networking type
for the IP clock.
The LTE
currently does
not support L3
Multicast
function.
LST
IPCLKLINK
LOFD-0030130
2
LOFD-0030130
3
LOFD-003023
Synchronization
with Ethernet
(ITU-T G.8261)
IEEE1588 V2
Clock
Synchronization
Clock over IP
(Huawei
proprietary)
IEEE 1588v2
over IPv6
GUI Value
Range:UNICAS
T(Unicast),
L3_MULTICA
ST(L3
Multicast),
L2_MULTICA
ST(L2
Multicast)
Unit:None
Actual Value
Range:UNICAS
T,
L3_MULTICA
ST,
L2_MULTICA
ST
Default
Value:UNICAS
T(Unicast)
Issue 01 (2013-04-28)
72
SingleRAN
Common Clock Feature Parameter Description
9 Parameters
Parameter ID
NE
MML
Command
Feature ID
Feature Name
Description
CIP
BTS3900
ADD
IPCLKLINK
WRFD-050501
Clock Sync on
Ethernet in
NodeB
DSP
IPCLKLINK
LST
IPCLKLINK
GBFD-118606
GBFD-118620
LOFD-0030130
1
LOFD-0030130
2
LOFD-0030130
3
LOFD-003023
Clock over IP
Clock over IP
support 1588v2
Synchronization
with Ethernet
(ITU-T G.8261)
IEEE1588 V2
Clock
Synchronization
GUI Value
Range:Valid IP
address
Unit:None
Actual Value
Range:Valid IP
address
Default Value:
0.0.0.0
Clock over IP
(Huawei
proprietary)
IEEE 1588v2
over IPv6
SIP
BTS3900
ADD
IPCLKLINK
LST
IPCLKLINK
WRFD-050501
GBFD-118606
GBFD-118620
LOFD-0030130
1
LOFD-0030130
2
LOFD-0030130
3
LOFD-003023
Clock Sync on
Ethernet in
NodeB
Clock over IP
Clock over IP
support 1588v2
Synchronization
with Ethernet
(ITU-T G.8261)
IEEE1588 V2
Clock
Synchronization
Clock over IP
(Huawei
proprietary)
IEEE 1588v2
over IPv6
Issue 01 (2013-04-28)
73
SingleRAN
Common Clock Feature Parameter Description
9 Parameters
Parameter ID
NE
MML
Command
Feature ID
Feature Name
Description
SYNMODE
BTS3900
SET
CLKMODE
WRFD-050501
Clock Sync on
Ethernet in
NodeB
LST
CLKMODE
GBFD-118620
LOFD-003013
LOFD-0030130
1
LOFD-0030130
2
LOFD-0030130
3
LOFD-003023
Clock over IP
support 1588v2
Enhanced
Synchronization
Synchronization
with Ethernet
(ITU-T G.8261)
IEEE1588 V2
Clock
Synchronization
Clock over IP
(Huawei
proprietary)
IEEE 1588v2
over IPv6
GUI Value
Range:ABSOL
UTE
(ABSOLUTE),
RELATIVE
(RELATIVE),
OFF(OFF)
Unit:None
Actual Value
Range:ABSOL
UTE,
RELATIVE,
OFF
Issue 01 (2013-04-28)
74
SingleRAN
Common Clock Feature Parameter Description
Parameter ID
NE
MML
Command
9 Parameters
Feature ID
Feature Name
Description
Default
Value:OFF
(OFF)
SN
BTS3900
ADD
SYNCETH
None
None
LST SYNCETH
PN
BTS3900
ADD
SYNCETH
LST SYNCETH
WRFD-050502
GBFD-118202
LOFD-003013
LOFD-0030130
1
Clock Sync on
Ethernet
Synchronous
Ethernet
Enhanced
Synchronization
Synchronization
with Ethernet
(ITU-T G.8261)
Issue 01 (2013-04-28)
75
SingleRAN
Common Clock Feature Parameter Description
9 Parameters
Parameter ID
NE
MML
Command
Feature ID
Feature Name
Description
SSM
BTS3900
ADD
SYNCETH
WRFD-050502
Clock Sync on
Ethernet
Meaning:Indicates whether
handling of
SSM frames is
supported.The
setting of this
parameter is
consistent with
the setting on the
Ethernet clock
server. The
synchronization
status message
(SSM) carries
clock quality
information,
which is
specified in
ITU-T. This
parameter is
valid only when
the
synchronousEthernet clock
link is of the
input type.
MOD
SYNCETH
DSP SYNCETH
LST SYNCETH
GBFD-118202
LOFD-003013
LOFD-0030130
1
Synchronous
Ethernet
Enhanced
Synchronization
Synchronization
with Ethernet
(ITU-T G.8261)
GUI Value
Range:DISABL
E(DISABLE),
ENABLE
(ENABLE)
Unit:None
Actual Value
Range:DISABL
E, ENABLE
Default
Value:DISABL
E(DISABLE)
Issue 01 (2013-04-28)
76
SingleRAN
Common Clock Feature Parameter Description
9 Parameters
Parameter ID
NE
MML
Command
Feature ID
Feature Name
Description
CIPV6
BTS3900
ADD
IPCLKLINK
WRFD-050501
Clock Sync on
Ethernet in
NodeB
DSP
IPCLKLINK
LST
IPCLKLINK
GBFD-118620
LOFD-0030130
1
LOFD-0030130
2
LOFD-0030130
3
LOFD-003023
SIPV6
BTS3900
ADD
IPCLKLINK
LST
IPCLKLINK
WRFD-050501
GBFD-118620
LOFD-0030130
1
LOFD-0030130
2
LOFD-0030130
3
LOFD-003023
Issue 01 (2013-04-28)
Clock over IP
support 1588v2
Synchronization
with Ethernet
(ITU-T G.8261)
IEEE1588 V2
Clock
Synchronization
GUI Value
Range:Valid IP
address
Unit:None
Clock over IP
(Huawei
proprietary)
Actual Value
Range:Valid IP
address
IEEE 1588v2
over IPv6
Default Value:
0:0:0:0:0:0:0:0
Clock Sync on
Ethernet in
NodeB
Clock over IP
support 1588v2
Synchronization
with Ethernet
(ITU-T G.8261)
IEEE1588 V2
Clock
Synchronization
GUI Value
Range:Valid IP
address
Unit:None
Clock over IP
(Huawei
proprietary)
Actual Value
Range:Valid IP
address
IEEE 1588v2
over IPv6
Default Value:
0:0:0:0:0:0:0:0
77
SingleRAN
Common Clock Feature Parameter Description
9 Parameters
Parameter ID
NE
MML
Command
Feature ID
Feature Name
Description
LN
BTS3900
ADD
SYNCETH
WRFD-050502
Clock Sync on
Ethernet
DSP SYNCETH
MOD
SYNCETH
RMV
SYNCETH
LST SYNCETH
GBFD-118202
LOFD-003013
LOFD-0030130
1
Synchronous
Ethernet
Enhanced
Synchronization
Synchronization
with Ethernet
(ITU-T G.8261)
GUI Value
Range:0~1
Unit:None
Actual Value
Range:0~1
Default Value:0
Issue 01 (2013-04-28)
78
SingleRAN
Common Clock Feature Parameter Description
10 Counters
10
Counters
Issue 01 (2013-04-28)
79
SingleRAN
Common Clock Feature Parameter Description
11 Glossary
11
Glossary
For the acronyms, abbreviations, terms, and definitions, see the Glossary.
Issue 01 (2013-04-28)
80
SingleRAN
Common Clock Feature Parameter Description
12
12 Reference Documents
Reference Documents
1.
2.
Synchronization Feature Parameter Description for GSM BSS, WCDMA RAN, and
eRAN
Issue 01 (2013-04-28)
81