Академический Документы
Профессиональный Документы
Культура Документы
Users Manual
(For CLP-9001R / 9301R Printers)
Contents
CAUTION .....................................................................2
1 Function of the peeler .......................................3
2 Loading the media (paper) ................................3
3 Unloading the liner (backing material) ...........6
4 Peeler operation ...................................................7
5 Peeling position ...................................................7
6 Commands ............................................................8
7 Main specifications of peeler ............................9
CAUTION
Always use the peeler with the right side cover (viewed from the front of
the printer) closed except when the media (paper) is being loaded.
When opening the right side cover, ensure it is fully open and resting on
the end stops on top of the main printer cover before making
adjustments, loading or unloading the media.
Do not knock or scratch the peeling sensors located on the small bars
protruding from the front of the printer. They are in close proximity to the
control panel and behind the front door.
Use standard label media (paper) with liner. Unsuitable media may cause
paper jams or improper operation.
Wipe off dirt, dust, glue residues, etc. stuck to the peeler with a soft cloth
that is soaked in a neutral detergent. Always switch off the power to the
printer and remove the power cord before cleaning.
For details about the normal method of loading media in to the printer, please see the
users manual of the printer. This manual is only concerned with the additional specific
requirements for the peeler operation.
CAUTION
Notch
(2) Route the media out to the front of the print head / platen mechanism as shown
and described in detail in the user manual leaving about 60cm (2 ft) of excess
media beyond the front of the platen.
(3) Peel off labels from the liner (manually, by fingers) over the first part of the
media in a length of about 60cm (2 ft). Then route the media out to the peeling
roller at the front of the printer.
(4) Pull the peeling roller towards the front of the printer about 1cm (0.39) to easily
pass the peeled liner under the front mechanism block to the rewinder shaft as
shown.
Right path
L-shaped bar of
peeler lever
Peeling roller
Wrong path
L-shaped bar of
peeler lever
Labels
removed from
excess media
Rewinder shaft
(5) Wind the beginning part of the peeled liner around the rewinder shaft and turn it
counterclockwise.
(6) Fix the peeled liner with the U-shaped stopper pin supplied.
CAUTION
The U-shaped stopper pin can be fitted only one way round!
Be careful that the longer shaft of the stopper pin is fitted in the shallow groove
of the rewinder shaft. The liner is sandwiched between the longer shaft of the
stopper pin and the groove. The shorter shaft of the stopper pin is fitted in the
deep groove of the rewinder shaft without sandwiching the liner.
Rewinder shaft
Longer shaft of U-shaped
stopper pin to be fitted in
shallow groove of rewinder
shaft
Shorter shaft of
U-shaped stopper pin
to be fitted in deep
groove of rewinder
shaft
Liner
(7) Lastly turn the rewinder shaft counterclockwise to remove any slack in the
media or liner. Remember to lower the print head and pinch rollers and lock
them in place.
Black lever of
paper full sensor
4 Peeler operation
Enable the Peel ON from the control panel of the printer
You must enable the peeling function using the control panel of the
printer. Please refer to the users manual for detailed operation of the
Menu System. A brief explanation is as follows:
* After
Print
Peel/Cut
Function
From the menu system, select the *After Print Menu Group.
Choose the Peel/Cut Function from the list of menu items and
select the Peel On function from the possible values.
Peel On
* Save
Settings
5 Peeling position
The peeling or tear position will be set automatically if the value Peel ON is selected
via the control panel or software. The distance fed between sensor position and
peeling position is a 132.9mm (5.23). To adjust peeling position by software use the
STX fnnn command. The command-designated value will be valid until a reset is
performed. For details, see the Command Reference manual.
The peeling position can also be set from the control panel. The value
of the Paper Position within the After Print menu group can be
adjusted from 20.3mm (0.8) to 76.2mm (3). For details, see the
users manual of the printer.
Peeling position =
Tear position
Paper
Position
Position
0.00mm
Printhead position
Sensor position
87 mm (3.43)
45.9 mm (1.81)
f = 132.9 mm (5.23)
6 Commands
The following commands are related to operation of the peeler. For details of each
command, see the separate Command Reference manual.
Label
Label removed
with fingers
Sensor
Sensor
: 0.07 mm (0.0027)
a
c
Direction of feed
CAUTION
10
JK74909-00
Printed in Japan