Академический Документы
Профессиональный Документы
Культура Документы
Foreword
John Crane
Type 5610 and 5610Q
Single O-ring Cartridge
Seal Assembly and
Installation Instructions
These instructions are provided to familiarize the user with the seal and its
designated use. The instructions must be read and applied whenever work
is done on the seal, and must be kept available for future reference.
ATTENTION
Safety Instructions
5. If the pumped fluid is hazardous or toxic, appropriate precautions
must be taken to ensure that any seal leakage is adequately
contained. Further information on sealing hazardous or toxic fluids
should be obtained from John Crane prior to seal installation.
ATTENTION
ATTENTION
1. Check the pump at the coupling for proper alignment of the driver
or motor.
2. Ensure that the gland plate nuts/bolts are securely tightened
according to the pump manual instructions, and that all screws are
securely fastened.
3. Complete the assembly of the pump, and turn the shaft (by hand if
possible) to ensure free rotation.
WARNING:
I-5610/5610Q
-1-
General Instructions
1. Study the Engineering layout drawing to confirm the proper seal
arrangement for the pump being used. Type 5610 and 5610Q seals
are designed for versatility and can be assembled in various ways.
The following instructions describe the standard configurations.
13
11
10
7
Part Name
1 Mating Ring
2 O-ring
3 Primary Ring
4 O-ring
5 Sleeve Assembly
6 O-ring
7
8
9
10
11
12
Collar
Set Screws
Spacers
Cap Screws
Gland Plate Assembly
Spring
13
14
15
16
17
Gasket
Snap Ring
O-ring
Drive Ring
Anti X-Ring
17
16 12
15
14
0.040"
63
20
BORE
0D +0.000"
- 0.002"
SHAFT OR SLEEVE
0.040 LG. X 20 CHAM.
MOUNT
DIAL INDICATOR
ON SEAL CHAMBER
FACE
NOTE: If measured dimensions exceed those values given, correct the equipment to meet specifications prior to seal installation.
6. Set the gland plate assembly gasket side down on table. Install
collar on gland plate assembly and engage spacers into groove,
aligning spacers with pipe taps of gland plate. Uniformly finger
tighten the cap screws.
3. Stand sleeve on its base and slide mating ring over sleeve, align pins
and press in place.
12. Align notches on primary ring tail with drive ring tabs and press
into bore of retainer. Make sure primary ring is engaged into tabs
and moves freely.
13. Place gland plate onto table with gasket side up.
14. Insert seal assembly in gland plate, align pins and press in place.
Turn gland plate over and confirm that retainer is flush with end of
gland plate.
I-5610/5610Q
-2-
L90 MIN.
L91
MIN. BOX
DEPTH
NEAREST OBSTRUCTION
SLOT
WIDTH
L39
L23
L90 MIN.
L91 MIN.
BOX DEPTH
L56
L23
N
L92
NEAREST OBSTRUCTION
L39
L56
D26
L92
D26
63
D4
63
D4
D2
D3
L12
L12
D1
D1
D2
1.375
1.500
1.625
1.750
1.937
2.062
2.170
2.312
2.437
2.562
2.687
2.812
3.062
3.312
3.312
3.375
3.625
3.750
3.750
4.000
4.125
4.218
4.343
4.468
4.593
4.718
4.843
5.093
5.343
5.843
6.093
6.343
D4
Min. Max.
1.445 1.889
N/A 2.015
N/A 2.294
N/A 2.421
2.007 2.680
2.132 2.812
2.240 2.918
2.382 2.918
2.507 3.015
2.632 3.360
2.757 3.485
2.882 3.610
N/A 3.891
N/A 4.062
N/A 4.062
N/A 4.186
N/A 4.469
3.853 4.600
3.853 4.600
4.125 4.850
4.250 4.975
4.343 5.100
4.468 5.199
4.593 5.375
4.718 5.500
4.843 5.625
4.968 5.750
5.218 6.000
5.468 6.313
5.968 7.260
6.218 7.510
6.468 8.000
I-5610/5610Q
D26
4.000
4.125
4.250
4.375
4.875
5.000
5.250
5.250
5.500
5.859
6.500
6.500
6.750
6.750
6.750
7.000
7.750
7.875
7.437
8.125
8.250
8.375
8.750
8.750
9.000
9.000
9.250
9.500
10.375
12.000
12.250
12.687
L12
1.989
2.062
2.062
2.062
2.156
2.156
2.156
2.156
2.375
2.375
2.375
2.484
2.484
2.500
2.500
2.500
2.500
2.562
2.562
2.562
2.562
2.562
2.562
2.562
2.562
2.562
2.562
2.562
2.562
2.953
2.953
2.953
L23
1.353
1.446
1.446
1.446
1.487
1.487
1.487
1.487
1.601
1.601
1.601
1.717
1.717
1.625
1.625
1.725
1.787
1.593
1.593
1.593
1.593
1.593
1.593
1.593
1.593
1.593
1.593
1.593
1.593
1.749
1.749
1.749
L39
1.954
2.062
2.062
2.062
2.125
2.125
2.125
2.125
2.312
2.312
2.312
2.466
2.562
2.500
2.500
2.500
2.562
2.562
2.510
2.562
2.562
2.562
2.562
2.562
2.562
2.562
2.562
2.562
2.562
3.043
3.043
3.043
L56
0.531
0.531
0.531
0.531
0.593
0.593
0.593
0.593
1.063
1.593
0.593
0.625
0.625
0.625
0.625
0.625
0.685
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
L90
2.000
2.125
2.125
2.125
2.187
2.187
2.187
2.187
2.375
2.375
2.375
2.528
2.625
2.562
2.562
2.562
2.625
2.687
2.635
2.687
2.687
2.687
2.687
2.687
2.687
2.687
2.687
2.687
2.687
3.168
3.168
3.168
L91
0.160
0.125
0.125
0.125
0.156
0.156
0.156
0.156
0.187
0.187
0.187
0.143
0.125
0.125
0.125
0.125
0.125
0.125
0.177
0.125
0.125
0.125
0.125
0.125
0.125
0.125
0.125
0.125
0.125
0.125
0.125
0.125
L92
0.035
N/A
N/A
N/A
0.031
0.031
0.031
0.031
0.062
0.062
0.062
0.018
N/A
N/A
N/A
N/A
N/A
N/A
0.052
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
M
N
0.525 2.805
0.525 2.933
0.525 3.213
0.525 3.338
0.525 3.599
0.562 3.766
0.562 3.875
0.562 3.875
0.562 4.000
0.687 4.469
0.687 4.566
0.687 4.719
0.687 5.000
0.687 5.170
0.687 5.170
0.687 5.312
0.812 5.720
0.812 5.845
0.812 5.845
0.812 6.095
0.812 6.220
0.687 6.250
0.687 6.770
0.812 6.636
0.812 6.761
0.812 6.886
0.812 7.011
0.812 7.261
0.812 7.574
0.812 10.000
0.812 10.250
0.937 10.500
-3-
D3
1.564
1.689
1.812
1.939
2.187
2.312
2.406
2.549
2.673
2.798
2.923
3.048
3.301
3.551
3.551
3.614
3.864
4.022
4.022
4.246
4.371
4.500
4.625
4.750
4.875
5.000
5.125
5.375
5.625
6.125
6.375
6.625
D4
Min. Max.
1.625 1.889
1.750 2.015
1.875 2.294
2.000 2.421
2.250 2.680
2.375 2.812
2.480 2.918
2.625 2.918
2.750 3.015
2.875 3.360
3.000 3.485
3.125 3.610
3.375 3.891
3.625 4.062
3.625 4.062
3.687 4.186
3.934 4.469
4.125 4.600
4.125 4.600
4.375 4.850
4.500 4.975
4.625 5.100
4.724 5.199
4.875 5.375
5.000 5.500
5.125 5.625
5.250 5.750
5.500 6.000
5.750 6.313
6.250 7.260
6.500 7.510
6.750 8.000
D26
4.000
4.125
4.250
4.375
4.875
5.000
5.250
5.250
5.500
5.859
6.500
6.500
6.750
6.750
6.750
7.000
7.750
7.875
7.437
8.125
8.250
8.375
8.750
8.750
9.000
9.000
9.250
9.500
10.375
12.000
12.250
12.687
L12
2.575
2.651
2.728
2.728
2.744
2.744
2.744
2.744
2.963
2.963
2.963
3.063
2.980
3.088
3.088
3.088
3.088
3.156
3.093
3.156
3.156
3.156
3.156
3.156
3.156
3.156
3.156
3.156
3.156
3.609
3.609
3.609
L23
1.353
1.446
1.446
1.446
1.487
1.487
1.487
1.487
1.601
1.601
1.601
1.717
1.717
1.625
1.625
1.725
1.787
1.593
1.593
1.593
1.593
1.593
1.593
1.593
1.593
1.593
1.593
1.593
1.593
1.749
1.749
1.749
L39
1.954
2.062
2.062
2.062
2.125
2.125
2.125
2.125
2.312
2.313
2.313
2.466
2.563
2.500
2.500
2.500
2.562
2.562
2.510
2.562
2.562
2.562
2.562
2.562
2.562
2.562
2.562
2.562
2.562
3.043
3.043
3.043
L56
0.531
0.531
0.531
0.531
0.593
0.593
0.593
0.593
1.032
0.593
0.593
0.625
0.625
0.625
0.625
0.625
0.685
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
L90
2.000
2.125
2.125
2.125
2.187
2.187
2.187
2.187
2.375
2.375
2.375
2.528
2.625
2.562
2.562
2.562
2.625
2.687
2.635
2.687
2.687
2.687
2.687
2.687
2.687
2.687
2.687
2.687
2.687
3.168
3.168
3.168
L91
0.746
0.714
0.791
0.791
0.744
0.744
0.744
0.744
0.775
0.775
0.775
0.722
0.542
0.713
0.713
0.713
0.651
0.719
0.708
0.719
0.719
0.719
0.719
0.719
0.719
0.719
0.719
0.719
0.719
0.691
0.691
0.691
L92
0.621
0.589
0.666
0.666
0.619
0.619
0.619
0.619
0.650
0.650
0.650
0.597
0.417
0.588
0.588
0.588
0.526
0.594
0.583
0.594
0.594
0.594
0.594
0.594
0.594
0.594
0.594
0.594
0.594
0.566
0.566
0.566
M
N
0.525 2.805
0.525 2.933
0.525 3.213
0.525 3.338
0.525 3.599
0.562 3.766
0.563 3.875
0.563 3.875
0.562 4.000
0.687 4.469
0.687 4.566
0.687 4.719
0.687 5.000
0.687 5.170
0.687 5.170
0.687 5.312
0.812 5.720
0.812 5.845
0.812 5.845
0.812 6.095
0.812 6.220
0.687 6.250
0.687 6.770
0.812 6.636
0.812 6.761
0.812 6.886
0.812 7.011
0.812 7.261
0.812 7.574
0.812 10.000
0.812 10.250
0.937 10.500
D2
1.750
2.170
2.312
2.562
3.062
3.312
3.312
D4
Min. Max.
2.875 3.023
3.500 3.925
3.625 3.734
3.875 4.250
4.750 5.078
4.625 4.740
4.750 4.875
D26
5.375
6.500
6.500
7.250
8.000
8.000
8.000
L12
2.062
2.156
2.156
2.375
2.484
2.500
2.500
L23
1.446
1.487
1.316
1.570
1.697
1.619
1.697
L39
2.062
2.125
1.954
2.282
2.407
2.329
2.407
L56
0.625
0.656
0.485
0.749
0.749
0.578
0.656
L90
2.125
2.187
2.017
2.407
2.625
2.454
2.532
L91
0.250
0.250
0.327
0.219
0.204
0.296
0.218
L92
0.125
0.125
0.202
0.094
0.079
0.171
0.093
Min.
N Turn Diam.
4.062 3.268
5.093 3.885
5.093
*
5.687 4.264
6.062 5.139
6.062
**
6.062 5.139
Seal
Size/D1
1.375
1.750
1.875
2.125
2.500
2.625
2.750
D3
1.939
2.406
2.549
2.798
3.301
3.551
3.551
D4
Min. Max.
2.875 3.023
3.500 3.925
3.625 3.734
3.875 4.250
4.750 5.078
4.625 4.740
4.750 4.875
D26
5.375
6.500
6.500
7.156
8.000
8.000
8.000
L12
2.062
2.156
2.156
2.375
2.484
3.088
2.500
L23
1.446
1.487
1.316
1.570
1.697
1.619
1.697
L39
2.062
2.125
1.954
2.282
2.407
2.329
2.407
L56
0.625
0.656
0.485
0.749
0.656
0.578
0.656
L90
2.125
2.187
2.017
2.407
2.532
2.454
2.532
L91
0.791
0.744
0.915
0.806
0.698
0.884
0.806
L92
0.666
0.619
0.790
0.681
0.573
0.759
0.681
M
0.562
0.687
0.687
0.687
0.687
0.687
0.687
Min.
N Turn Diam.
4.062 3.268
5.093 3.885
5.093
*
5.687 4.264
6.062 5.000
6.062
**
6.062 5.139
LUBRICANT
Vegetable Oil, Animal Oil, Mineral-Hydrocarbon Oils,
Soap Solution, Parker Super-O-Lube, Silicone Grease
Ethylene Propylene
Perfluoroelastomer
(i.e. Kalrez)
NOTE: Always use a lubricant that is compatible with your machinery and product.
Use lubricant sparingly, only enough to install seal with ease.
Viton and Kalrez are registered trademarks of DuPont.
Polywater is a registered trademark of American Polyware Co.
GLAND BOLTS
CAP SCREWS
SPACERS
SET SCREWS
O-RING
I-5610/5610Q
-4-
For DIN pumps rotate gland 135 CCW. Use port #2 as flush.
NOTE: For CCW (counter clockwise) rotation pumps,
consult John Crane Engineering.
Quench Q
Port #1
Port #2
Port #3
Port #4
- Not Drilled
- Flush
- Not Drilled
- Not Drilled
Port #1
Port #2
Port #3
Port #4
Flush F
- Quench
- Flush
- Drain
- Not Drilled
Flush F
Clockwise
Rotation
Clockwise
Rotation
Type 5610
Type 5610Q
Drain D
Maintenance
Quality Assurance
This seal has been assembled in accordance with John Crane Quality
Assurance Standards and with proper maintenance and use will give safe
and reliable operation to the maximum recommended performance as
shown in any relevant approved John Crane publication.
I-5610/5610Q
-5-
Ordering Information
Primary Ring
Mating Ring
Cartridge Hardware
Secondary Seal
Carbon Graphite
Silicon Carbide (optional)
Nickel Binder Tungsten Carbide (optional)
Silicon Carbide
Nickel Binder Tungsten Carbide (optional)
316 Stainless Steel*
Fluoroelastomer*
Operating Limits
Pressure:
Temperature:
Speed:
*Various options.
5610
H-SP-39543
H-SP-37305
H-SP-39554
H-SP-37306
H-SP-39564
H-SP-39574
H-SP-37307
H-SP-37308
H-SP-39584
H-SP-37309
H-SP-39594
H-SP-39604
H-SP-37310
H-SP-37311
H-SP-37312
H-SP-39614
H-SP-39624
H-SP-41625
H-SP-41630
H-SP-41636
H-SP-41641
H-SP-41646
H-SP-41651
H-SP-41954
H-SP-41656
H-SP-41661
H-SP-41664
H-SP-41668
H-SP-41671
H-SP-41674
H-SP-41677
H-SP-41680
Seal Size
1.375
1.750
1.875
2.125
2.500
2.625
2.750
5610Q
H-SP-39545
H-SP-37313
H-SP-39556
H-SP-37314
H-SP-39566
H-SP-39576
H-SP-37315
H-SP-37316
H-SP-39586
H-SP-37317
H-SP-39596
H-SP-39606
H-SP-37318
H-SP-37319
H-SP-37320
H-SP-39616
H-SP-39626
H-SP-41626
H-SP-41631
H-SP-41637
H-SP-41642
H-SP-41647
H-SP-41652
H-SP-41955
H-SP-41657
H-SP-41662
H-SP-41666
H-SP-41669
H-SP-41672
H-SP-41675
H-SP-41678
H-SP-41681
5610
H-SP-38057
H-SP-38067
H-SP-38077
H-SP-39034
H-SP-39007
H-SP-38087
H-SP-39017
5610Q
H-SP-38058
H-SP-38068
H-SP-38078
H-SP-39035
H-SP-39008
H-SP-38088
H-SP-39018
For your nearest John Crane facility, please contact one of the locations below.
North America
Morton Grove, IL, USA
Europe
Slough, UK
Latin America
So Paulo, Brazil
Asia Pacific
Singapore
1-800-SEALING
Tel: 1-847-967-2400
Fax: 1-847-967-3915
Tel: 44-1753-224000
Fax: 44-1753-224224
Tel: 55-11-3371-2500
Fax: 55-11-3371-2599
Tel: 971-481-27800
Fax: 971-488-62830
Tel: 65-6518-1800
Fax: 65-6518-1803
If the products featured will be used in a potentially dangerous and/or hazardous process, your John Crane representative should be consulted prior to their selection and use. In the
interest of continuous development, John Crane Companies reserve the right to alter designs and specifications without prior notice. It is dangerous to smoke while handling products
made from PTFE. Old and new PTFE products must not be incinerated. ISO 9001 and ISO 14001 Certified, details available on request.
2014 John Crane
I-5610/5610Q
Revised 5/12
www.johncrane.com
-6-
www.johncranetoday.com
I-5610/5610Q