Академический Документы
Профессиональный Документы
Культура Документы
Version: 001
Date:2009/05/26
Notice:
- For RO to input specific Legal Requirement in specific NS regarding to responsibility and liability
statements.
- Please check BenQs eSupport web site, http://esupport.benq.com, to ensure that you have the most
recent version of this manual.
First Edition (May, 2009)
Copyright BenQ Corporation 2009. All Right Reserved.
-1-
Content Index
Abbreviations & Acronyms .............................................................................. 3
1 About This Manual......................................................................................... 3
1.1. Trademark ............................................................................................................ 3
2 Introduction .................................................................................................... 4
2.1.
2.2.
2.3.
2.4.
2.5.
-2-
1.1. Trademark
The following terms are trademarks of BenQ Corporation:
BenQ
Importance
Only trained service personnel who are familiar with this BenQ Product shall perform
service or maintenance to it. Before performing any maintenance or service, the
engineer MUST read the Safety Note.
-3-
2 Introduction
This section contains general service information, please read through carefully. It should be
stored for easy access place for quick reference.
-4-
3 Product Overview
3.1. Specification
3.1.1
Introduction
G2420HD is defined 24W LCD Monitor supports WXGA (1920x1080) resolution with DPMS
(Display Power Management System) and Senseye function. There are three different input types,
D-sub, DVI and HDMI, of models. G2420HD adopts AUO panel, M240HW01 V2.
The features summary is shown as below,
*All panel spec. in service manual definition depends on the variance of panel source.
*All spec. of monitor need to warm up at least 1hr.
* To test the Contrast Ratio and Luminance functions, the color status must be User preset
mode.
1. Contrast Ratio: Set brightness at 100, and contrast at 50.
2. Luminance: Set brightness at 100, and contrast at 100.
Feature items
Panel supplier & module name
Screen diagonal
Display Format
Pixel Pitch
Specifications
AUO M240HW01 V2
24W
531.36(H) x 298.89(V)
0.276 mm x 0.276 mm
R/L:85/85 degrees (typ)
Viewing Angle (@ Contrast Ratio >= 10) and U/D: 80/80 degrees
(typ)
Remark
TN, Normally white
609.7mm
Panel Display information
per one triad
-5-
Yes
Yes
Yes
No
No
I-Key function
DDC2B
DDC-CI
Yes
No
Yes
Yes
No
No
Yes
Operational Specification
Power supply
Condition
Universal input full
range
90 ~ 264VAC
Normal On operation
DPMS Off state
DPMS Sleep state
110 VAC
220 VAC
264 VAC/50Hz
1. 1500VAC, 1 sec
2. Ground test: 30A,
1sec
IEC1000-4-4
Spec
OK N.A Remark
90~264VAC /47~63Hz
< 2.0 Arms
<49 W
<1W
<1W
< 30 A (peak)
< 60A (peak)
< 3.5 mA
Without damage
< 0.1 ohm
1KV
Common: 2KV,
IEC1000-4-5 (Surge)
Differential: 1KV
(on-line test)
(in-lab test)
90 ~ 264VAC
3~8mA
CCFL Frequency
90 ~ 264VAC
40KHz ~ 80KHz
Color: Black
Length: 1500 +/- 50
mm
-6-
Cold-start
Power cord
LED: Green
LED: Off
LED: Amber
Depends on panel
source
Depends on panel
source
3.1.2.2
Item
Signal interface
Condition
15-pin D-Sub
Signal Cable
24-pin DVI-D
15-pin D-sub
connector
24-pin DVI-D
connector
19-pin HDMI
connector
Signal type
Level
Impedance
Pin assignment
Analog input
Impedance
Sync Pulse Width
(SPW)
Level
Impedance
Digital input
(Positive/Negative)
Logic High: 2.4V ~
5.5V
down)
0.7s < H-SPW
1H < V-SPW
600mV for each
differential line
50 Ohm TDR Scan
See Note-3
Level
OK N.A Remark
See Note-2
Signal type
Sync input
Spec
Color: Black
Length: 1500 +/- 30
mm
Color: Black
Length: 2000 +/- 50
mm
See Note-1
1
2
3
4
5
6
7
8
PSignal Assignment
Pin
Signal Assignment
Red video
Green video
Blue video
Ground
Cable Detected
Red Ground
Green Ground
Blue Ground
9
10
11
12
13
14
15
-7-
to
VESA
Standard
10K
application
for
1
2
3
4
5
6
7
8
9
10
11
12
PSignal Assignment
TMDS RX2TMDS RX2+
TMDS Ground
Floating
Floating
DDC Clock
DDC Data
Floating
TMDS RX1TMDS RX1+
TMDS Ground
Floating
Pin
13
14
15
16
17
18
19
20
21
22
23
24
Signal Assignment
Floating
+5V Power
Ground
Hot Plug Detect
TMDS RX0TMDS RX0+
TMDS Ground
Floating
Floating
TMDS Ground
TMDS Clock+
TMDS Clock-
-8-
3.1.2.3
Item
Video performance
Condition
Spec
OK N.A Remark
Both for analog and
170 MHz
digital inputs
Both for analog and
1920x1080@60
digital inputs
1920 x 1080 @
<5.89 ns
60Hz
(50% of minimum pixel
(max. support
clock period)
timing)
Refer to VESA
< 5% final full-scale
VSIS Standard
value
V1R1
Refer to VESA
< 12% of step function
voltage level over the
VSIS Standard
full voltage range
V1R1
3.1.2.4
Scan range
Item
Horizontal
Vertical
Condition
Spec
24-83 KHz
50-76 Hz
3.1.2.5
Plug & Play DDC2B DDC-CI Support
Item
Condition
Spec
DDC channel type
EDID
DDC2B
Version 1.3
DDC-CI
-9-
OK N.A Remark
OK N.A Remark
Refer to BenQ LS
EDID definition.
Refer to BenQ
DDCCI requirement
definition.
3.1.2.6
Support Timings
- 10 -
3.1.3
3.1.3.1
Video performance
*All spec. of monitor need to warm up at least 1hr.
Item
Condition
Spec
Any input resolution
Resolution
modes which are under
1920 x 1080
1920x1080
Contrast ratio
600(min),1000(typ)
Brightness
At R/G/B saturated
condition
Response time
Gray to Gray
Viewing angle
At Contrast ratio = 10
CIE coordinate of White
Display colors
Average response time
Response time with AMA of gray level to gray
level
- 11 -
2 ms (typ.)
At Contrast ratio = 10
OK NA Remark
6 bit+FRC
Test Condition: Set
Contrast at 50,
Brightness at 90,
Color at User
preset.
3.1.3.2
Item
Spec
28 dB/A
OK NA Remark
Refer to C326
Condition
Operating
Non-operating
Spec
0 ~ +40
-20 ~ +60
Operating
10 ~ 90%
Non-operating
10 ~ 90%
OK NA Remark
Non
condensing
Non
condensing
Without
packing
With packing
Environment
Temperature
Humidity
Operating
Altitude
0~3048m (10,000ft)
Non-operating
3.1.3.5
Item
0~12,192m (40,000ft)
Transportation
Condition
(1) Vibration
Spec
OK NA Remark
(1) Sine wave
5~200Hz
1.5G,
1
octave/min, 15 min dwell
on
each
resonant
frequency, all primary
axis, one sweep (30 min
minimum)
per
orientation, total of 90+
min.
Package, Non-Operating
(2) Random
5 ~100 Hz, 0 dB/Oct.
0.015 g2/Hz
100 ~200 Hz, -6 dB/Oct.
200 Hz, 0.0038 g2/Hz
Equivalent to 1.47 Grms,
All primary axis, 20 min
per- orientation, total is
60 min.
- 12 -
(3) Procedure:
Confirmed sample with
appearance and function
ready
before testing then
compare with after test
record as brightness,
uniformity and contrast
ratio. Perform random
vibration after sine-wave
vibration test.
Test Spectrum:
20 Hz 0.0185(g2/Hz)
200Hz 0.0185(g2/Hz)
Unpackaged, Non(2) Unpackaged Vibration
Duration : 5 Minutes
Operating
Axis : 3 axis
( Horizontal and Vertical
axis ,Z axis)
91 cm Height (MP stage)
(3) Drop
Package, Non-Operating (1 corner, 3 edges, 6
faces)
Waveform: half sine
Faces: 6 sides/ per
Wooden package, Nonorientation
(4) Shock
Operating
3 shocks.
Duration: <3ms
Velocity accelerate: 75g
3.1.3.6
Item
EMC
Condition
Electric
TCO03
Magnetic
FCC part 15J class B
EMI
EN55022 class B
3.1.3.8
Item
OK NA Remark
Spec
OK NA Remark
Band 1 < 10 V/m
Reliability
MTBF Prediction
CCFL Life time
Condition
Spec
Refer to MIL-217F
At 252, under 7.0mA
OK NA Remark
Excluding
CCFL
See Note-4
Note-4: CCFL lifetime is determined as the time at which brightness of lamp is 50%. The typical
lifetime of CCFL is on the condition at 7.0mA lamp current.
- 13 -
3.1.3.9
Audio performance (Ear-Jack, For HDMI audio only)
Item
Condition
Spec
OK NA Remark
Preamp + Power amp
(1)Output power
1 Wrms/CH @ 1KHz
(2)THD (@ 1W)
<1%
(3)S/N ratio
>40dB
Speaker Driver
(1)Nominal impedance
4 ohm
(3)Frequency response
180~20KHz SPL-10dB
level
2
(5)Dimension of box
284x60x27mm
Audio Control
(1)Volume range
0 ~100 levels
(2)Mute
On/Off
3.1.4
LCD Characteristics
OK N.A Remark
6 bit + HiFRC
Typ.
Max.
85
85
80
80
1000
3.4
1.6
5
2
0.649
0.338
0.289
0.609
0.146
7.4
2.6
10
0.679
0.368
0.319
0.639
0.176
Remark
Color
White
Coordinates
Luminance Uniformity
Blue y
White x
White y
9 points
measurement
(CIE)
[%]
0.04
0.283
0.299
0.07
0.313
0.329
75
80
0.10
0.343
0.359
User Controls
Spec
OK NA Remark
Spec
Auto-Geometry
OK NA Remark
Bluish
Reddish
Normal
17 languages
Recall All
Standard / Dynamics /
Movie / Photo/sRGB
D-sub
DVI
HDMI
Color
OSD Position
OSD Time
OSD Lock
Language
Recall
Mode
Input Select
- 15 -
Sharpness
Display Information
For input timing
Volume
For HDMI Audio only
Mute
For HDMI Audio only
The detailed firmware functions specification, please refer to C212 S/W spec. document.
3.1.6
Mechanical Characteristics
3.1.6.1 Dimension
Item
Bezel opening
Monitor without Stand
Monitor with Stand
Carton Box (outside)
Condition
W x H x D mm
W x H x D mm
L x W x H mm
3.1.6.2 Weight
Item
Monitor (Net)
Monitor
with
(Gross)
Spec
533.2*300.7 mm
570*348.42*63.26mm
570*412.6*183.94mm
636*133*482 mm
Tilt: -3.5 ~ +21.5 degree
Swivel: 0 degree
Condition
packing
3.1.6.3 Plastic
Item
Flammability
Heat deflection To
UV stability
Condition
ABS
ABS
Resin
Texture
Color
3.1.6.4 Carton
Item
Color
Material
Compression strength
Burst Strength
Stacked quantity
Condition
Remark
Spec
4.91Kg
OK N.A Remark
6.5Kg
Spec
>ABS<,94-HB
65
Delta E < 8.0
MPRII: ABS
(SD0150/GP35/D150/PA
757/HP-126/T0103)
MT-11010
BCS-7015A
OK N.A Remark
Spec
Kraft
A Flute
250 KGF
19.2 KGF/cm2
5 Layers
- 16 -
OK N.A
OK N.A Remark
3.1.7
40'
Quantity of Products
(sets)
(Every Pallet)
Pallet A: 76
Pallet B: 68
Pallet C: 24
Pallet A: 76
Pallet B: 68
X
Quantity of pallet
(sets)
(Every Container)
Pallet A: 4
Pallet B: 4
Pallet C: 2
Pallet A: 9
Pallet B: 9
X
4.9Kg
6.5Kg
Package:
Carton Interior Dimension (mm)
L*W*H
570*412.6*183.94mm
636*133*482 mm
Certification
Item
Environment
PC-Monitor
Safety
Dimension w/ Base
W*H*D (mm)
624*121*456 mm
3.1.8
Condition
Spec
Green design
Blue Angel
German Standard
E-2000
EPA
TCO99
TCO03
Green Mark
Microsoft Windows
DPMS
DDC 2B
USB
UL (USA)
CSA (Canada)
Nordic / D.N.S.F
- 17 -
Switzerland
USA Standard
OK N.A Remark
ISO14000
Requirement
PC98/99
VESA
Version 1.3
External
UL60950 3rd edition
CAN/CSA-C22.2 No.
60950
EN60950
FIMKO
CE Mark
CB
CB
TUV/GS
EMC
X- Ray Requirement
CCC (China)
GOST
SASO
CE Mark
FCC (USA)
EN55022
CISPR 22
VCCI (Japan)
BSMI (Taiwan)
C-Tick (Australia)
DHHS (21 CFR)
DNHW
German X- Ray
standard
PTB
Ergonomics
EN60950
73/23/EEC
IEC60950
EN60950
EN60950 /
EK1-ITB 2000:2003
CB4943
EN60950
IEC60950
89/336/EEC
FCC Part 15 B
Class B
Class B
VCCI Class B
CNS 13438
AS/ NZS CISPR22
USA X- Ray Standard
TUV / Ergo
ISO 13406-2
prEN50279
- 18 -
- 19 -
3.2.6.
CLASSIFICATION OF DEFECTIVES
A defective is a product which contains one or more defects. The defective will be
classified into following classes.
Critical defective
A critical defective contains one or more critical and may also contain major and/or minor
defects.
Major defective
A major defective contains one or more defects and may also contain minor defects but
contains no critical defect.
Minor defective
A minor defective contains one or more minor defects but contains no critical and major
defects.
3.2.7.
EXPRESSION OF DEFECTIVES
Number of defects
Percent of defects = ------------------------------------------ X 100%
Number of products inspected
3.2.8.
INSPECTION STANDARD
Unless otherwise specified, the inspection standard will be defined by MIL- STD105E(ISO-2859), SINGLE SAMPLING PLAN. level II is in use all the time , inspection
levels are normal ,reduce and tighten .
Acceptance Quality Level
When a critical defect is found, this must be reported immediately upon detection, the lot
or batch shall be rejected and further shipments shall be held up pending instructions
from the responsible person in relevant organization.
Major Defective: 0.4 AQL
Minor Defective: 1.50 AQL
3.2.9.
GENERAL RULES
The inspection must be carried out by trained inspectors having good knowledge of the
meaning of "fitness for use". The inspection must be based upon the documents
concerning the completely assembled and packed product when more defects appear
with the same cause only the most serious defect must be taken into account. Defects
found in accessories packed with the product as connecting cables, plugs, adapters and
the like, and being inspected as a part of the complete product, must be included in the
evaluation.
The evaluation must be within the limits of the product specification and, for not specified
characteristics, be related to the design model, limit samples or judgment of a jury of
experts. Faults must be demonstrable.
- 20 -
3.2.10.
TEST CONDITIONS
Unless otherwise prescribed, the test conditions are as follows:
. Nominal mains voltage
Temperature: +5~+35
. Warm up time : 30minutes minimum .
. Visual inspection shall be down with the distance from eyes to the sample 35-50 cm .
. Display mode: Primary mode 1920 x 1080
3.2.11.
TEST EQUIPMENTS
1. PC with display adapter or other specific
display adapter which is agreed upon by both parties
2. Test program by BenQ
3. Ruler
4. Power saving test tool
5. Minolta color analyzer ( CA-110 or BM 7 )
- 21 -
Class
Major
Minor
Minor
Major
Major
Major
Major
Major
Major
Major
Major
Major
Major
Major
Minor
Major
Major
Major
Major
Major
No
3.4
3.5
3.6
3.7
3.8
3.9
3.10
3.11
3.12
3.13
3.14
3.15
3.16
3.17
3.18
3.19
3.20
3.21
3.22
3.20
3.21
3.23
3.24
3.25
3.26
3.27
3.28
3.29
4
4.1
4.2
4.3
4.4
4.5
4.6
4.7
4.8
5
5.1
5.2
5.3
5.4
5.5
5.6
5.7
5.8
5.9
5.10
Description
Poor print of logo or name plate
Label on product Wrong or missing
Scratched or dirty but legible spec. label
GAP between LCD and front bezel is over 2.0 mm
Dot/area discolor over 1mm dia. in front or over 2mm dia. in other areas
Cabinet warped, sagged or bulging 0.5% of surface length
Cabinet warped, sagged or bulging noticeable but 0.5% of surface length
Sharp stud or edge, which can cause damage not safe
Finishing of piece parts will not arrived in good condition at the customer
Cabinet step ( between housing and bezel ) 1.0mm , < 1.5mm
Cabinet step ( between housing and bezel ) 1.5mm
Wiring or fixing cord comes out of cabinet or jammed
Auxiliary material used during production not removed
Cabinet parts come loose during normal handling, not safe
Cabinet parts come loose during normal handling, but safe
Tilt/swivel too flexible/not working
Tilt/swivel stiff
Dirty front bezel and housing cant remove
Dirty front bezel and housing removable easily
Sticker or loose user control switch which will not function correctly
Missing knob or switch, not safe
Missing knob or switch, but safe
Poor functional user controls in mechanical
Unreadable printing of user controls label
Rubber foot missing
LED wrong material or missing
LED sagged >1.0mm or bulging>0.5mm
Wrong S/N between spec. label and monitor display
AC power and signal cable
AC power or connector not correct or damaged, not safe
AC power or connector not correct or damaged, but safe
Signal cable contact pin dirty
Signal cable plug dirty or surface damaged, but safe
Cable crack
Cable scratch ( wire not exposed ), or dirty
AC-DC adapter no function
Signal cable contact pin dirty
Interior of the product
Use Non-QVL ( Qualify vendor list )component
Wrong parts, broken component, but safe
Foreign material
Conductive (Has potential to short circuit)
Non-conductive (Moveable)
Missing hardware, component or screw, stripped screw
Loose hardware/screw or insufficient torque
Poor wire routing, which is no concerned on EMI
Cold soldering/loose connections (Electrical)
Wires and mechanical structure do not meet UL/CSA or TUV
Wrong parts, broken component, not safe
Component burn
- 22 -
Class
Major
Major
Minor
Major
Major
Major
Minor
Major
Major
Minor
Major
Major
Major
Critical
Major
Major
Minor
Major
Minor
Major
Critical
Major
Major
Major
Major
Major
Minor
Major
Critical
Major
Minor
Minor
Major
Major
Minor
Major
Major
Major
Major
Minor
Major
Major
Minor
Major
Critical
Critical
Critical
PATTERN
FULL WHITE
DARK
TEST ITEM
H - Size , V Size
.Viewing Angle
Light Output
Impurity, Spot check
Contrast Ratio
Brightness adjust Range
Background, Spot check
FULL W , R , G , B
256 COLORS
Color Check
16 GREY
Gray Check
Electric characteristics
- 23 -
OK
170 MHz
1920x1080@60
<5.89 ns
(50% of minimum pixel
clock period)
N.A Remark
Both for analog and
digital inputs
Both for analog and
digital inputs
Settling
Time
after
< 5% final full-scale value
overshoot /undershoot
< 12% of step function
Overshoot/Undershoot
voltage level over the full
voltage range
Specification
Line defect
Cant be seen
Bright Dot
<=2 dots
Green bright
dots
<=2 dots
Dark dots
<=4 dots
<=5 dots
Continuous
Defect
Note:
This Panel Specification is subject to change. Please check it on eSupport system for latest update.
- 24 -
Print Cord
I2C Board
Check the Jumpers on the I2C circuit board (make sure J5/J6/J7/J8 are set at Pin 1 & Pin 2 short)
Connected to print
cord and PC
Connected to Display
Signal Cable
- 25 -
1.
2.
- 26 -
Step6: Check result, If the words showed in red, need to run the program again
3.
6.
4.
5.
- 27 -
- 28 -
Step 2: Click Open File and select VGA or HDMI EDID file
- 29 -
- 30 -
- 31 -
D. Color adjustment:
1. Setup input timing ICL-605, white pattern.
2. Confirm auto color adjustment had already done.
3. Measure color temperature by Minolta CA-110 (or equivalent equipment).
4. Check the color temperature Bluish, Reddish & Normal. The color temperature
specification as follows:
White Balance
X+0.283+(-) 0.015
(Bluish, 9300K set on OSD)
Y+0.297+(-) 0.015
White Balance
X+0. 326+(-) 0.015
(Reddish, 5800K set on OSD)
Y+0. 342+(-) 0.015
White Balance
X+0.313+(-) 0.015
(sRGB, 6500K set on OSD)
Y+0. 329 +(-) 0.015
- 32 -
F. Command definition :
PC Host will send 0x7C IIC slave address and then following 4 bytes command
Byte Byte
I2C Send Command
Byte1 2
3
Byte4 OK N.A. Remark
cksu
Write Contrast to MCU RAM
CA 55 Data m
cksu
Write Brightness to MCU RAM
CA 56 Data m
cksu
Write data to MCU RAM
Write Red Gain to MCU RAM
CA 57 Data m
screen immediately.
Dont store data to
cksu
EEPROM.
Write Blue Gain to MCU RAM
CA 59 Data m
cksu
Read Contrast from MCU RAM
C3 55 XX m
cksu
Read Brightness from MCU RAM
C3 56 XX m
cksu
Write User R-Gain Data to EEPROM
AA 6C Data m
cksu
Write User G-Gain Data to EEPROM
AA 6D Data m
cksu
Write User B-Gain Data to EEPROM
AA 6E Data m
- 33 -
AA
7C
AA
7D
AA
7E
AA
92
AA
93
AA
AA
AA
cksu
Data m
cksu
Data m
cksu
Data m
cksu
Data m
cksu
Data m
1=C1/9300/Bluish,
2=C2/6500/sRGB/,
3=C3/5800/Reddish,
4=User, 5=Cx
cksu
1~4 m
cksu
95 Data m
cksu
96 Data m
94
AA
AA
AA
AA
AA
AA
A3
A3
A3
A3
A3
- 34 -
cksu
97 0~17 m
cksu
98 Data m
cksu
99 Data m
cksu
9A Data m
cksu
9E Data m
cksu
9F Data m
cksu
3C XX m
cksu
3D XX m
cksu
3E XX m
cksu
4C XX m
cksu
4D XX m
1=English, 3=French,
0=Deutsch, 4=Italian,
2=Spanish, 5=JAPAN,
6=, 7=
8=Hungarian,
9=Serbian, 0A=Russian,
0B=Dutch, 0C=Polish,
0D=Czech, 0E=Swedish,
0F=Portugese,
10=Romanian
A3
4E
XX
A3
5C
XX
A3
5D
XX
A3
5E
XX
A3
6C
XX
A3
6D
XX
A3
6E
XX
A3
7C
XX
A3
7D
XX
A3
7E
XX
A3
92
XX
A3
93
XX
A3
94
A3
95
A3
96
A3
97
A3
98
A3
99
A3
9A
A3
9E
- 35 -
cksu
m
cksu
m
cksu
m
cksu
m
cksu
m
cksu
m
cksu
m
cksu
m
cksu
m
cksu
m
cksu
m
cksu
m
1=C1/9300/Bluish,
2=C2/6500/sRGB/,
3=C3/5800/Reddish,
4=User, 5=Cx
cksu
XX m
cksu
XX m
cksu
XX m
cksu
XX m
cksu
XX m
cksu
XX m
cksu
XX m
cksu
XX m
1=English, 3=French,
0=Deutsch, 4=Italian,
2=Spanish, 5=JAPAN,
6=, 7=
8=Hungarian,
9=Serbian, 0A=Russian,
0B=Dutch, 0C=Polish,
0D=Czech, 0E=Swedish,
0F=Portugese,
10=Romanian
A3
9F
CC
01
CC
02
CC
03
CC
04
CC
05
CD
01
CD
02
On burn in mode
CE
01
CE
XX*
CF
01
CF
XX*
C0
00
C0
01
C0
02
C0
03
C1
00
C1
01
C1
02
C1
03
AC
23
AC
24
AC
25
AC
33
AC
34
- 36 -
cksu
XX m
cksu
XX m
cksu
XX m
cksu
XX m
cksu
XX m
cksu
XX m
cksu
XX m
cksu
XX m
cksu
XX m
cksu
XX m
cksu
XX m
cksu
XX m
cksu
XX m
cksu
XX m
cksu
XX m
cksu
XX m
cksu
XX m
cksu
XX m
cksu
XX m
cksu
XX m
cksu
Data m
cksu
Data m
cksu
Data m
cksu
Data m
cksu
Data m
Reserved
Change Sense-Eye
mode immediately. And
store the index to
EEPROM.
Change luminance
sensor mode
immediately. And store
the index to EEPROM.
cksu
Data m
cksu
Data m
cksu
Data m
cksu
Data m
cksu
Data m
cksu
Data m
cksu
Data m
cksu
XX m
cksu
XX m
cksu
XX m
cksu
XX m
cksu
XX m
cksu
XX m
cksu
XX m
cksu
XX m
cksu
XX m
cksu
XX m
cksu
XX m
NA NA
NA NA
AC
35
AD
23
AD
24
AD
25
AD
33
AD
34
AD
35
AE
23
AE
24
AE
25
AE
33
AE
34
AE
35
1A
5A
1B
5A
1C
5A
1E
5A
1F
55
BB
5A
NA
NA
55
NA
NA
NA
BB
NA
NA
NA
44
NA
NA
NA
33
NA
NA
C0
0~3
NA
cksu
XX m
- 37 -
cksu
D0 Data XX m
ckssu
D1 Data XX m
PowerOFF: Data=AA
PowerON: Data=Other
Value
Asia: Data=AA
European: Data=Other
Value
EEPROM Bank R/W (For Debug using only, not for Production Line Write EEPROM directly)
Addr
cksu
Read EEPROM Bank 0
B0 ess XX m
Addr
cksu
Read EEPROM Bank 1
B1 ess XX m
Addr
cksu
Read EEPROM Bank 2
B2 ess XX m
Addr
cksu
Write EEPROM Bank 0
B8 ess Data m
Addr
cksu
Write EEPROM Bank 1
B9 ess Data m
Addr
cksu
Write EEPROM Bank 2
BA ess Data m
(For 24C08 type)
Addr
cksu
Write EEPROM Bank 3
BB ess Data m
- 38 -
R-Byte1
FC
R-Byte2
AA
FC
FC
CF
13
14
15
16
17
21
20
8
7
12
6
10
11
18
22
19
23
- 39 -
5E.0BJ06.001
5E.0RM03.001
5E.0RM02.001
5E.0RM01.011
5F.LUDB0.051
* This Service BOM is subject to change. Please check it on eSupport and SPO system before
service parts order release.
- 40 -
picture
Operation
Disassemble the stand
2 screws
- 41 -
Tool
Notes
Screw-driver
When disassembly
the bezel ,notice
dont bend the
C/B .man must wear
glove
The purpose is
loose the BZL
- 42 -
- 43 -
10
Disassemble the
hexangular screws
( four or two )
10
11
- 44 -
Screw-driver
picture
Operation
Put panel on the
cushion carefully,
- 45 -
Tool
Notes
Screw
driver:5+0.6kg
Screw driver:
Side mount:
30.6
Other:
40.6
- 46 -
Screw driver :
71kg
Use location
tool ,location the bkt on
panel
10
11
- 47 -
location tool:
G24101
12
13
14
15
- 48 -
Screw driver(if
it need) :
3+0.5KG
1.750.05
#1
16
Screw driver :
7.5+0.5kg
17
Screw driver :
9.0+1.0kg
18
- 49 -
BenQ G900HD
BenQ G2220HD
BenQ G2020HD
BenQ G2410HD AUO
BenQ G2410HD CMO
BenQ T2200
BenQ G2420HD/G2420HDB
A
56.69mm
84mm
69mm
78.65mm
72.65mm
56.69mm
78.65mm
B
40mm
44.5mm
42mm
57.2mm
55.85mm
40mm
57.2mm
C
40mm
44.5mm
42mm
57.2mm
55.85mm
40mm
57.2mm
AL-Tape
AL-Tape
L Shape Tooling
- 50 -
5.4. Packing
- 51 -
- 52 -
Power off
Y
Turn on power
N
Does cable plugs in connector?
Y
Is 5V from power
board normal ?
N
Check Power BD 5V
output
Y
Is Power LED light Green or
amber?
Y
Y
Does crystal work correctly?
Y
Is interface BD normally?
Replace interface BD
Y
N
Plug LVDS cable again
or replace it
- 53 -
No
Plug control BD then retry
Is control BD connecting?
Yes
Yes
Is bottom key normally?
No
Replace Control BD
Is OSD working??
No
Check Interface BD
Is control BD working?
Replace control BD
Check interface BD
- 54 -
Panel or I/F
BD or Audio
no function
DC/DC
converter
+5V(+5.4V) valid?
Yes
No
No
Replace components
IC
Check IC851
Vcc valid?
Yes
No
Check F851
OK?
No
Yes
AC/DC converter
- 55 -
Replace F851
No
Replace IC851
components
- 56 -
5.6.4.3 Inverter
Panel lamp
no work
Check V-INVERTER
OK?
No
AC/DC converter
Yes
No
DC/DC converter
Yes
Check BL_ON,
BRT_ADJ
OK?
No
No
Replace IC801
components
Yes
Check IC801
frequency, output
OK?
Yes
Replace components
- 57 -
- 58 -
(c) IC introduction:
1.) DDC (Display Data Channel) function: We use DDC IC to support DDC2Bi function. DDC
data is store in 24C02 (EEPROM). Those data related to LCD monitor specification. PC
can read them by SDA and SCL serial communication for IC communication for
DDC2Bi.
2.) Scalar IC: There are A/D, TMDS receiver, Scaling, OSD and LVDS transmitter functions
built-in the RTD2482D IC. Scaling IC is revolutionary scaling and color engine, capable
of expanding any source resolution to a highly uniform and sharp image or down scaling
from 1920x1080, combined with the critically proven integrated 8 bit triple-ADC and
patented Rapid-lock digital clock recovery system. It also support detect mode and
DPMS control.
3.) MCU embedded in Scalar: Control unit, it controls all the functions of this interface board,
just like the OSD display setting, the adjustable items, adjusted data storage, the external
IIC communication, support DDC2Bi. .
4.) EEPROM: We use 24C16 to store all the adjustable data, user settings and uses two
24C02 to store D-SUB, DVI and HDMI data.
5.) Flash-rom stores source code.
A-2.) Control board introduction
There are 6 keys for user's control which includes Power, Menu, Right/Plus, Left/Minus,
Auto, and Enter. The following descriptions are the introduction of these keys.
(1) Power key: to turn/off power of monitor
(2) Menu key: to enter sub-menus or select items.
(3) Right/Plus key: to select previous and to increase adjustment and Brightness /Contrast
Popup submenu hotkey
(4) Left/Minus key: to select next and to decrease adjustment and Senseye Mode Popup
submenu hotkey
- 59 -
Rectifier
and filter
PWM
controller
Isolation
power
transformer
Rectifier and
filter
Switching element
Rectifier and
filter
Inverter
circuit
SW regulator
Feedback
Isolation
Fig.1
#1 EMI Filter
This circuit (fig. 2) is designed to inhibit electrical and magnetic interference for meeting FCC,
VDE, VCCI standard requirements.
2
TR601
NTC 5
1
L4
L602
C601
0.22U M
C604
2200PF
19MH
C602
0.22U M
C603
2200PF
N3
Fig. 2
- 60 -
L6
GSIB4A60-LF
BD601
+ 1
2
4 -
C605
150U 450V
<Spec>
Fig. 3
#3 Switching element and Isolation power transformer
When the Q601 turns on, energy is stored in the transformer. During Q601 turn-off period, the
stored energy is delivered to the secondary of transformer. C614, R607, C607 and D601 are
snubber circuits. R615 is current sense resistor to control output power. (See Fig.4)
L605
E2
Z45/100MHZ
C607
0.001U J
R607
68K
E3
K
T601
12
D601
UF4007-LF
2
E4
L604
Z45/100MHZ
E5
10
11
L603
5
Q601
Z45/100MHZ
C614
100P K
4
R615
0.22
Fig. 4
- 61 -
A2
R702
100
3
C704
1000P K
C705
1000P K
10
11
Fig. 5
- 62 -
C701
470U 35V
RC1820
1
+
C702
470U 35V
RC1820
+
2
D702
Y G862C15RSC
R701
100
12
V-INVERTER
T601
D701
Y G862C15RSC
A1
J
A2
C703
470U 35V
RC1820
#5 PWM Controller
The TEA1530(A)T can be used in Fixed Frequency converter designs for low voltage,
high current applications. At low power (standby) levels, the system operates in cycle
skipping mode which minimizes the switching losses during standby.
The proprietary high voltage BCD800 process makes direct start-up possible from the
rectified universal mains voltage in an effective and green way. A second low voltage
BICMOS IC is used for accurate, high speed protection functions and control.
The TEA1530(A)T enables highly efficient and reliable supplies to be designed easily.
L605
E1
E3
Z45/100MHZ
C607
0.001U J
R607
68K
C605
150U 450V
<Spec>
E2
T601
12
D601
UF4007-LF
2
E4
R605
10K
L604
Z45/100MHZ
E5
R606
C612
1U K
R620
100K F
Gnd
HVS
Protect Driv er
Ctrl
R617
10K F
Sense
5
Z45/100MHZ
C608
1000P K
Q601
STP7NK80ZFP
R612
10 J
R614
1K F
C611
100PF 50V J
C614
100P K
R613 68K F
C613
1U 25V
ZD601
TZMC20
Drain
R622
10K F
C616 1U K
R615
0.22
90V ?W Protection
264V ?W Protection
C610
3300P J
11
L603
D602
EGP10D-LF
10 J
C606
47U 50V
10
NXP1530
1
Vcc
E6
IC601
R611
27
R618
4.7K
K
ZD602
TZMC6V2
Fig. 6
- 63 -
K
R616
68K
A
D605
LL4148
#6 Feedback circuit
PC123 is a photo-coupler and KA431 is a shunt regulation. They are used to detect the
output voltage change and be the primary and secondary isolation. When output voltage
changes, the feedback voltage will be compared and duty cycle will be decided to control the
correct output voltage. (See Fig.7)
R708
2K
R711
22K F
C709
0.1U K
R709
10K F
IC602
PC123FY 1J00F
R707
10K
R
IC702
R712
3.32K F
KA431AZT A_NL
Fig. 7
#7 DC-DC circuit
IC851(PWM IC TL1451) is used to convert V-INVERTER to other voltage needed.
F851
32V 2A
R864
3.3K
R865
22K
Q853
PMBS3904
R876
2.05K F
IC851-10
FD851
SB360-LF
Q854
2N3906S
C863
470P K
+ C865
220U 25V
R877
1.2K F
R866
22
R853
10K F
C864
0.1U
1
Q853-B
2
C860
0.1U
MCU_3.3V
+ C862
220U 25V
R863
330
R860
22K
AUDIO_CTRL
R861
2.7K J
R856
330K
L851
D
C853
1U K
47U
R852
Q857-B 2.7K
B
Q857
2N3906S
Q851
2SJ598
Q853-C
V-INVERTER
C855
0.01U K
R855
47K
9
VCC
Q852
2SJ598
Q855-C
C859
1U K
C857
220P K
K
A
FD853
ERB83-004
C868
470P K
R874
3.09K F
C869
0.1U
1
FD852
ERB83-004
+ C871
220U 25V
2
E
E
Q856
2N3906S
B
C
R862
2.7K J
C858
0.01U K
1U K
R858
330K
Q855
PMBS3904
Q855-E
IC851-7
R873
47K
R857
C85610K F
R872
22K
R871
3.3K
C
+ C867
220U 25V
2
R851
10K F
PANEL_5V
47U
1
C851
470P K
L852
D
GND
1OUT
1DTC
1FBK
1IN-
RT
CT
1IN+
IC851
TL1451ACN
C852
0.1U K
2OUT
11
2FBK
2DTC
10
IC851-14
12
13
C854
220P K
2IN-
14
15
SCP
2IN+
RFF
16
R854
10K F
R859
10K F
IC851-3
- 64 -
R882
22
L853
Z45/100MHZ
R875
1K F
F851
32V 2A
R853
10K F
C855
0.01U K
R863
330
R854
10K F
R855
47K
R851
10K F
R858
330K
10
9
VCC
11
2DTC
C858
0.01U K
R859
10K F
- 65 -
GND
8
P13
R873
47K
R857
10K F
1OUT
1DTC
C857
220P K
1IN-
1FBK
5
RT
CT
1
C851
470P K
1IN+
IC851
TL1451ACN
C852
0.1U K
C856
1U M
2OUT
12
13
2IN-
2FBK
15
14
SCP
2IN+
RFF
16
C854
220P K
C859
1U M
P-MOSFET Q852 is used for switching of step-down converter. And FD852/FD853 are the
flywheel diodes.
R874/R875 determine the feedback to IC851 to set up the output to +5V or +3.3V.
V-INVERTER
Q852
2SJ598
VCC
11
10
2OUT
R874
3.09K F
FD853
ERB83-004
C869
1200P K
1
C
Q856
2N3906S
FD852
ERB83-004
+ C871
220U 25V
C868
470P K
R882
22
R862
2.7K J
Q855
PMBS3904
P10
K
R872
22K
R871
3.3K
+ C867
220U 25V
1
GND
8
1OUT
7
1DTC
1FBK
1IN-
PANEL_+5V
L852
47U
RT
1IN+
3
CT
IC851
TL1451ACN
L853
Z45/100MHZ
2FBK
2DTC
12
13
2IN-
14
2IN+
15
SCP
RFF
16
F851
32V 2A
R875
1K F
- 66 -
Full-Bridge Configuration
ZD801
TZMC6V2
Q801
P_A
R801
5.1K
4
5
6
8
7
N_B
C827
4.7U M
R811
10K
Q802
K
3
P_C
C829
4.7U M
T 801
.
5
A
FD801
ERB83-004
.
3
5
6
8
7
N_D
R812
10K
Fig. 1
Fig. 1: Q801, Q802 and T801 form a full-bridge configuration.
The full-bridge switch is configured such that Q801 N-MOS and Q8026 P-MOS are ON while
Q801 P-MOS and Q802 N-MOS are OFF in a half-cycle. During the next half cycle, Q801 NMOS and Q802 P-MOS are OFF while Q801 P-MOS and Q802 N-MOS are ON. This
develops an alternating current through the transformer primary.
The result in T801 primary coil has an AC square waveform.
Certainly, the secondary of T801 will produce high voltage AC sinusoidal waveform.
- 67 -
Feed-back Circuit
C815
100P J
F1
TP801
TP802
C819
5PF D
.
C820
470P J
.
3
10
11
12
13
14
15
NDR2
PDR1
GNDP
VDDA
TIMER
PWM
ISEN
OVPT
ENA
PDR2
GNDA
RT1
CT
SST/CMP
VSEN
8
7
C816
100P J
C821-2
.
2
6
5
2
2K62272102
R831 D801
511 F BAV99
TP803
TP804
C821
5PF D
1
2
CN802
1
2
2K62272102
R821
100K
R816
2.2K
C822
470P J
R822
20K F
4
3
2
1
C814
0.033U K
R834
1M
D809
LL4148
R820
20K F
16
NDR1
OZ9933
K
C831
0.22U K
F3
IC801
R815
2.2K
R819
100K
CN801
T 801
D805
BAV99
A
R827
365 F
Fig. 2
Fig. 2 shows the feedback circuit consists of a lamp, R816, D805, R827 and C814.
With the lamp current through D805, a half sine-waveform voltage signal is produced.
We may get the Maximum value through R827/C814.
After OZ9933 gets the feedback voltage signal from PIN14, the duty of the full-bridge
driver outputs is decided.
- 68 -
P/N
8F.205B4.019
8F.5A224.6R0
8F.EA324.6R0
3
8F.5A356.8R0
6K.L8810.001
8F.00273.6R0
8F.VZ524.6R0
8F.00518.100
8F.00003.143
DESCRIPTION
MOUNTING
MATERIAL
HOLE
TORQUE
SIZE
(KG-CM)
(MM)
Metal;
D-SUB;DVI
5.00.6
Connector
Metal
Side mount:
SCRW MACH
Metal to metal
30.6
Plastic to
Other:
FLATM3*0.5P*6L ZN
metal
40.6
None
tread 8
SCRW TAP FH M3*6L ZN
Metal
10
Have tread:
68
Metal
SCRW MACH FH M4*8L B- Metal to metal
9.01.0
ZN NYL
Plastic to
metal
ASSY SCREW M4*8L
Metal
FP726A NLK ISU
Metal to metal
9.01.0
(8F.5A456.8R0+4B.L7212.0
Plastic to
01)
metal
None
tread 8
Metal
Metal to metal
10
SCRW TAP PH F/10WSH
Plastic to
Have tread:
M3*6L C-ZN
metal
68
PCB to metal Aluminum:
4~5
None
tread 8
10
SCRW TAP FLAT+EXT
Metal
Have tread:
M3*6L C-ZN
Metal to metal
68
Aluminum:
4~5
None
Metal
tread 8
Metal to metal
10
SCRW TAP W/FL
Plastic to
Have tread:
M3*10L(S3.8)ZN
metal
68
SPEAKER to
Aluminum:
metal
4~5
Aluminum
SCRW TAP PAN #4-40*3/8
(Heatsink)
3.30.3
SCRW MACH HEX #440*0.3" N
- 69 -
Screw
Head
5.00.6 #4-40
M3*0.5
#2
2.680.0
3
#2
M4*0.7
#2
M4*0.7
#2
2.680.0
3
2.680.0
3
#2
#2
2.680.0
3
#2
2.60.03
#2
10 8F.VG234.6R0
Aluminum
(Heatsink)
Metal
Metal to metal
Metal
SCRW TAP
Metal to metal
8F.HA334.8R0
FPHM3*6(6/1)TP-S B-ZN
Plastic to
metal
Metal
SCRW MACH FLAT M4*8L Metal to metal
8F.5A456.8R0
C-ZN NYLO
Plastic to
metal
Metal
SCRW TAP CAP
Metal to metal
8F.WA324.6R0
M3*1.34P*6L B-NI
Plastic to
metal
Metal
8F.XA324.5R0 SCRW TAP M3*5L B-ZB
Metal to
Plastic
Metal
SCRW MACH PAN M4*5L Metal to metal
8F.1A526.5R0
NI
Plastic to
metal
11 8F.VZ526.6R0
None
tread 8
10
2.680.0
Have tread:
3
68
Aluminum:
4~5
#2
M4*0.7
#2
6~8
2.680.0
3
#2
9.01.0
M4*0.7
#2
5.01.0
2.350.0
5
#2
6~8
2.85~2.95
#2
8~10
M4*0.7P
#2
17
Metal
SCRW MACH PAN W/SPG Metal to metal
8F.1B524.3R0
M3*3L NI
Plastic to
metal
6~8
M3*0.5P
#2
18
Metal
SCRW MACH FLAT M3*4L Metal to metal
8F.5A524.4R0
NI(W2407 lift
Plastic to
metal
6~8
M3*0.5P
#2
19
8F.00573.5R0
6~8
M3*0.5P
#1
Metal
SCRW MACH FLAT M4*7L Metal to Metal
20 8F.5A456.7R0
B-ZN NYL
Plastic to
Metal
8~10
M4*0.7P
#2
Metal
Metal to metal
Plastic to
metal
8~10
M4*0.7P
#2
12
13
14
15
16
21
- 70 -
Metal
Metal to
Plastic
101.0
22
23
8F.00608.6R0
8F.XA313.8R0
24 8F.WA314.8R0
25
26
27
8F.00607.8R0
28
8F.5A322.2R4
29
8F.00551.3R0
30 8F.MA324.5R5
31
8F.XA326.100
- 71 -
PLASTIC
Plastic
Metal to plastic
Plastic to
plastic
PCB to plastic
Plastic
Metal to plastic
Plastic to
plastic
PLASTIC
Plastic
Metal to plastic
Plastic to
plastic
Plastic
Metal to plastic
Plastic to
plastic
PCB to plastic
Plastic
Metal to plastic
Plastic to
plastic
PCB to plastic
Plastic
Metal to plastic
Plastic to
plastic
PCB to plastic
Metal
Metal to metal
Plastic to
metal
Plastic
Metal to plastic
Plastic to
plastic
4.50.5
2.350.0
5
#2
4.00.5
2.00.05
#1
5.01.0
2.350.0
5
#2
4.50.5
2.350.0
5
#2
4.50.5
2.350.0
5
#2
4.00.5
2.680.0
3
#2
2.00.5
1.750.0
5
#1
2.00.5
1.750.0
5
#1
6~8
M3*0.5P
#2
8~10
3.450.0
5
#2
- 72 -
- 73 -