Вы находитесь на странице: 1из 3

PROPOSED TWO-STOREY JAIME HILARIO INTEGRATED SCHOOL - LA

SALLE
DIVISION
9 - FINISHES
SECTION 09 50 00
-Ceiling
May 2013

Project
:
Location :
DIVISION

Proposed Two-Storey Jaime Hilario Integrated School - La Salle


Banawang, Bagac, Bataan
9

SECTION 09 24 00

FINISHES
-

Ceiling

PART 1 GENERAL
1.1

PROJECT INCLUDES:

A. Ceiling Assemblies
1
2
3
4
B

Gypsum Board Attachment


1

1.2

Gypsum Board
Fiber Cement Board
Acoustic Ceiling Board
Steel framing system to receive boards.

Screws -attached to steel framing and furring.

QUALITY ASSURANCE
A

Fire, structural and seismic performance shall meet the requirement of


building code and local authorities.

Comply with the applicable provisions and recommendations of the following:


1

American Society of Testing and Materials (ASTM) Publications:


ASTM C36 Gypsum Wall board

Ceiling
09 50 00

ASTM C475

Joint Treatment Materials for Gypsum Backing Board

ASTM C645

Non-load (axial) Bearing Steel Studs, Runners (Track),


and Rigid Furring Channels for Screw Application of
Gypsum Board.

ASTM C754

Installation of Framing Members to Receive Screw


Attached Gypsum Wallboard, Backing Board or Water
Resistant Backing Board.

ASTM C840

Application and Finishing of Gypsum Board.

Page 1 of 3

PROPOSED TWO-STOREY JAIME HILARIO INTEGRATED SCHOOL - LA


SALLE
DIVISION
9 - FINISHES
SECTION 09 50 00
-Ceiling
May 2013
ASTM C1002
2

Gypsum Association (GA) Publications:


GA-201

Gypsum Board for Walls and Ceilings.

GA-216
PART 2
2.1

Steel Drill Screws for the Application of Gypsum Board.

Recommended Specifications for the Applications and


Finishing of Gypsum Board.

PRODUCTS

MATERIALS
A

Gypsum Board:

Standard Gypsum Board: 1200 mm x 2400 mm x 12.5mm thick,


maximum permissible length; ends square cut, tapered edges, on G.I.
furring channel.
Provide all accessories needed for complete
installation. For location, refer to Plans & Schedule of Finishes.

Moisture-Resistant Gypsum Board: 1200 mm x 2400 mm x 12.5mm


thick, maximum permissible length; ends square cut, tapered edges, on
G.I. furring channel.
Provide all accessories needed for complete
installation. For Toilets, Lockers, Laundry Room, Washing Areas, and
refer to Plans & Schedule of Finishes for other areas.

Joint treatment to conform to ASTM C475 and ASTM C840, 3 coat system

Acoustic Ceiling Board:


1
Provide Acoustic ceiling board with minimum Noise
Reduction Coefficient (NRC) rating = 0.75

Thickness: 1 inch (25mm)

Length = 2400 mm

Width = 1200 mm

Fiber Cement Boards


1

Length = 2440 mm

Width = 1220 mm

Thickness = 4.5 mm, 9.0mm

Bending Radius = 900 mm radius for 4.5 mm thk

Ceiling
09 50 00

Page 2 of 3

PROPOSED TWO-STOREY JAIME HILARIO INTEGRATED SCHOOL - LA


SALLE
DIVISION
9 - FINISHES
SECTION 09 50 00
-Ceiling
May 2013
5
D

Finish = Ready for Painting

Steel Framing for Suspended and Furred Ceilings

1 Furring Channels: ASTM C645 and GA-216, gauge 20 (0.80 mm) standard
channels.
2
1

PART 3
3.1

3. 2

Accessories: Hangers and inserts


Screw Fixed Suspended Ceiling System: For Gypsum Boards- concealed
G.I. furring channel suspension system, complete with rods, clips and
accessories.

Auxiliary Materials
1

Gypsum board nails: ASTM C514.

Fastening adhesive: GA-216.

Other hardware & accessories necessary

EXECUTION

JOINT TREATMENT
A

Tape, fill, and sand exposed joints, edges, and corners to produce smooth
surface ready to receive finishes.

Feather coats onto adjoining surfaces so that camber is maximum 1.6mm.

TOLERANCES
A

PART 4
A
B
152
exposed

Maximum Variation of Finished Gypsum Board Surface from True Flatness:


3mm in 3m in any direction.
SUBMITTALS
Product Data: Submit manufacturers product data and
installation instructions.
Samples: Submit selection and verification samples: 6 inch 6 inch (152
mm) sample for each wood ceiling unit required, showing full range of
texture to be expected in completed work

End of Section 09 50 00

Ceiling
09 50 00

Page 3 of 3

Вам также может понравиться