Академический Документы
Профессиональный Документы
Культура Документы
SECTION
ADP
CONTENTS
BASIC INSPECTION .................................... 5
DIAGNOSIS AND REPAIR WORKFLOW .......... 5
Work Flow ................................................................. 5
ADP
Description ...............................................................29
DTC Logic ................................................................29
Diagnosis Procedure ..............................................29
Special Repair Requirement ....................................29
Description ...............................................................30
DTC Logic ................................................................30
Diagnosis Procedure ..............................................30
ADP-1
2008 QX56
Description .............................................................. 34
DTC Logic ............................................................... 34
Diagnosis Procedure ............................................. 34
Description .............................................................. 52
Component Function Check .................................. 52
Diagnosis Procedure .............................................. 52
Component Inspection ............................................ 53
ADP-2
2008 QX56
Description .............................................................. 73
Component Function Check .................................. 73
Diagnosis Procedure .............................................. 73
Description ...............................................................97
Component Function Check ..................................97
Diagnosis Procedure ..............................................97
Description .............................................................. 75
Component Function Check .................................. 75
Diagnosis Procedure .............................................. 75
Description ...............................................................99
Component Function Check ....................................99
Diagnosis Procedure ...............................................99
Component Inspection ........................................... 101
ADP
ADP-3
2008 QX56
ADP-4
2008 QX56
BASIC INSPECTION
INFOID:0000000001735407
WORK FLOW
C
ADP
ALKIA0538GB
DETAILED FLOW
Revision: July 2007
ADP-5
2008 QX56
ADP-6
2008 QX56
Perform the DTC confirmation procedure (if DTC is detected) or component function check (if no DTC is
detected) again, and then check that the malfunction can be repaired securely.
Are all malfunctions corrected?
YES >> INSPECTION END
Symptom is detected.>> GO TO 4
DTC is detected.>> GO TO 7
ADP
ADP-7
2008 QX56
INFOID:0000000001735408
1. FOREIGN OBJECTS
Check the following:
objects on or behind the seats that could cause binding
objects under the seats that may be interfering with the seats moving parts
objects under pedals that may interfere with movement
Are there any foreign objects that could be causing interference?
YES >> Remove objects.
NO
>> GO TO 2
2. WIRING CONNECTIONS
1. Disconnect harness connectors.
2. Check terminals for damage or loose connections.
3. Reconnect harness connectors.
Are any connectors damaged or loose?
YES >> Repair or replace damaged parts.
NO
>> GO TO 3
INFOID:0000000001735409
Refer to Owners Manual for Automatic Drive Positioner system operating instructions.
ADP-8
2008 QX56
FUNCTION DIAGNOSIS
B
INFOID:0000000001735410
ADP
ALJIA0234GB
ADP-9
2008 QX56
INFOID:0000000001735411
ALJIA0235ZZ
1.
A. Steering column
B. Key switch and ignition knob
switch M12
C. BCM M18, M19, M20 (view with
instrument panel removed)
3.
4.
6.
A. Door mirrror LH D4, RH D107
B. Front door switch LH B8
C. Front door lock assembly LH (key
cylinder switch) D14
7.
5.
INFOID:0000000001735412
OUTLINE
The system automatically moves the driver seat, pedal assembly, steering wheel and door mirror position by
the driver seat control unit and the automatic drive positioner control unit. The driver seat control unit corresponds with the automatic drive positioner control unit by UART communication.
ADP-10
2008 QX56
Description
Manual function
The driving position (seat, pedal assembly, steering wheel and door mirror position)
can be adjusted by using the power seat switch, pedal adjusting switch, ADP steering
switch or door mirror remote control switch.
Memory function
The seat, pedal assembly and outside mirror move to the stored driving position by
pressing seat memory switch (1 or 2).
Exit
On exit, the seat moves backward and the steering wheel moves upward.
Entry
On entry, the seat and steering wheel return from exiting position to the previous driving position.
D
INFOID:0000000001735413
CONTROL UNITS
Item
Function
It communicates with the driver seat control unit via UART communication.
Perform various controls with the instructions of driver seat control unit.
Perform the controls of the pedal adjusting, steering wheel, door mirror and the
seat memory switch.
BCM
Transmit the following status to the driver seat control unit via CAN communication.
Front door LH: OPEN/CLOSE
Ignition switch position: ACC/ON
Door lock: UNLOCK (with Intelligent Key or remote keyless entry request switch
operation)
Key ID
Key switch: Insert/Pull out Intelligent Key
Starter: CRANKING/OTHER
Combination meter
Transmit the vehicle speed signal to the driver seat control unit via CAN communication.
AV control unit
The setting change of auto drive positioner system can be performed on the display.
Transmit the shift position signal (P range) to the driver seat control unit.
ADP
INPUT PARTS
Switches
Item
Key switch and ignition knob switch
Set switch
The registration and system setting can be performed with its operation.
Function
ADP-11
2008 QX56
Function
Sensors
Item
Function
Tilt sensor
Reclining sensor
Sliding sensor
OUTPUT PARTS
Item
Function
Tilt motor
Reclining motor
Sliding motor
MANUAL FUNCTION
ADP-12
2008 QX56
INFOID:0000000001735414
H
ALJIA0236GB
INFOID:0000000001735415
OUTLINE
The driving position (seat, pedal assembly, steering wheel and door mirror position) can be adjusted manually ADP
with power seat switch, pedal adjusting switch, ADP steering switch and door mirror remote control switch.
OPERATION PROCEDURE
1.
2.
3.
DETAIL FLOW
M
Seat
Order
1
Input
Power seat switch
(sliding, lifting, reclining)
Output
The power seat switch signal is inputted to the driver seat control
unit when the power seat switch is operated.
Motors
(sliding, lifting, reclining)
The driver seat control unit outputs signals to each motor according to the power seat switch input signal.
Adjustable pedals
ADP-13
2008 QX56
Input
Output
The automatic drive positioner control unit actuates the motor according to the operation of the pedal adjusting switch signal from
the driver seat control unit.
Motor
Sensor
(forward, backward)
The automatic drive positioner control unit recognizes any operation limit of each actuator via each sensor and will not operate
the actuator anymore at that time.
Output
The ADP steering switch signal is input to the automatic drive positioner control unit when the ADP steering switch is operated.
Input
ADP steering switch
Sensor
(upward, downward)
The automatic drive positioner control unit actuates the tilt motor
according to the operation of the ADP steering switch signal.
Motor
The automatic drive positioner control unit recognizes any operation limit of each actuator via each sensor and will not operate
the actuator anymore at that time.
Door Mirror
Order
1
Input
Door mirror remote
control switch
Output
The door mirror remote control switch signal is inputted to the automatic drive positioner control unit when the door mirror remote
control switch is operated.
Motors
(Door mirror motor)
NOTE:
The door mirrors can be operated manually when ignition switch is in either ACC or ON position. The ignition
switch signal (ACC/ON) is transmitted from BCM to the driver seat control unit via CAN communication and
from the driver seat control unit to the automatic drive positioner control unit via UART communication.
ADP-14
2008 QX56
INFOID:0000000001735416
I
ALJIA0235ZZ
1.
A. Steering column
B. Key switch and ignition knob
switch M12
C. BCM M18, M19, M20 (view with
instrument panel removed)
3.
4.
6.
A. Door mirrror LH D4, RH D107
B. Front door switch LH B8
C. Front door lock assembly LH (key
cylinder switch) D14
7.
5.
N
INFOID:0000000001735417
CONTROL UNITS
Item
ADP
Function
Operates the specific seat motor with the signal from the power seat switch.
Transmits the ignition switch signal (ACC/ON) via UART communication to the
automatic drive positioner control unit.
Transmits the pedal adjusting switch signal via UART communication to the automatic drive positioner control unit.
ADP-15
2008 QX56
Function
Operates the specific motor with the signal from driver seat control unit, ADP steering switch or door mirror remote control switch.
BCM
Recognizes the following status and transmits it to the driver seat control unit via
CAN communication.
Ignition position: ACC/ON
INPUT PARTS
Switches
Item
Function
Sensors
Item
Function
Tilt sensor
OUTPUT PARTS
Item
Function
Tilt motor
Reclining motor
Sliding motor
MEMORY FUNCTION
ADP-16
2008 QX56
INFOID:0000000001735418
H
ALJIA0237GB
INFOID:0000000001735419
OUTLINE
The driver seat control unit can store the optimum driving positions (seat, pedal assembly, steering wheel and ADP
door mirror position) for 2 people. If the front seat position is changed, one-touch (pressing desired memory
switch for more than 0.5 second) operation allows changing to the other driving position.
NOTE:
K
Further information for the memory storage procedure. Refer to Owners Manual.
OPERATION PROCEDURE
1.
2.
3.
OPERATION CONDITION
Satisfy all of the following items. The memory function is not performed if these items are not satisfied.
Item
Request status
Ignition position
ON
Switch inputs
Power seat switch
Pedal adjusting switch
ADP steering switch
Door mirror control switch
Set switch
Seat memory switch
O
OFF
(Not operated)
P position
DETAIL FLOW
ADP-17
2008 QX56
Input
Memory switch
Output
Motors
(seat, pedal adjusting,
tilt, door mirror)
Driver seat control unit operates each motor of seat when it recognizes the memory switch pressed for 0.5 second or more and requests
each motor operation to automatic drive positioner control unit via
UART communication. The automatic drive positioner control unit operates each motor.
Driver seat control unit judges the operating seat position with each
seat sensor input. The positions of the adjustable pedals and outside
mirror are monitored with each sensor signal that is input from auto
drive positioner control unit via UART communication. Driver seat
control unit stops the operation of each motor when each part reaches the recorded address.
Sensors
(seat, pedal adjusting, tilt, door mirror)
INFOID:0000000001735420
ALJIA0235ZZ
ADP-18
2008 QX56
4.
7.
5.
A. Steering column
B. Key switch and ignition knob
switch M12
C. BCM M18, M19, M20 (view with
instrument panel removed)
3.
6.
A. Door mirrror LH D4, RH D107
B. Front door switch LH B8
C. Front door lock assembly LH (key
cylinder switch) D14
B
A. A/T selector lever
B. A/T device (park position switch)
M203
E
INFOID:0000000001735421
CONTROL UNITS
Item
Function
Operates the pedal adjusting motor, tilt motor and door mirror with the instructions
from the driver seat control.
INPUT PARTS
Switches
ADP
Item
Memory switch 1/2
Function
The registration and memory function can be performed with its operation.
K
Sensors
Item
Function
Tilt sensor
Reclining sensor
Sliding sensor
OUTPUT PARTS
Item
Function
Tilt motor
Reclining motor
ADP-19
2008 QX56
Function
Sliding motor
Memory indicator
INFOID:0000000001735422
ALJIA0238GB
INFOID:0000000001735423
OUTLINE
When exiting, if the conditions are satisfied, the seat is moved backward and steering wheel is moved upwardfrom normal sitting position.
The seat slide amount at entry/exit operation can be changed.
NOTE:
This function is set to OFF before delivery (initial setting).
Further information for the system setting procedure. Refer to Owners Manual.
OPERATION PROCEDURE
1.
2.
OPERATION CONDITION
Satisfy all of the following items. The exit assist function is not performed if these items are not satisfied.
Item
Request status
Ignition switch
OFF
ON
Initialization
Done
ADP-20
2008 QX56
Request status
Switch inputs
Power seat switch
Pedal adjusting switch
ADP steering switch
Door mirror remote control switch
Set switch
Seat memory switch
A/T selector lever
OFF
(Not operated)
P position
DETAIL FLOW
D
Order
Input
Output
Driver seat control unit receives front door switch LH signal (open)
from BCM via CAN communication.
Driver seat control unit operates the seat sliding motor, which recognizes that the front door LH is opened with ignition switch OFF. Driver seat control unit then requests the operation of the tilt motor to the
automatic drive positioner control unit via UART communication.
The automatic drive positioner control unit operates the motor for a
constant amount.
G
INFOID:0000000001735424
ADP
ALJIA0235ZZ
ADP-21
2008 QX56
A. Steering column
B. Key switch and ignition knob
switch M12
C. BCM M18, M19, M20 (view with
instrument panel removed)
3.
4.
6.
A. Door mirrror LH D4, RH D107
B. Front door switch LH B8
C. Front door lock assembly LH (key
cylinder switch) D14
7.
5.
INFOID:0000000001735425
CONTROL UNITS
Item
Function
BCM
Recognizes the following status and transmits it to the driver seat control unit via
CAN communication.
Front door LH: OPEN/CLOSE
INPUT PARTS
Switches
Item
Front door switch LH
Function
Detect front door LH open/close status.
Sensors
Item
Function
Sliding sensor
Tilt sensor
OUTPUT PARTS
Item
Function
Sliding motor
Tilt motor
ADP-22
2008 QX56
INFOID:0000000001735426
H
ALJIA0238GB
INFOID:0000000001735427
OUTLINE
The seat and steering wheel are in the exiting position when either following condition (A or B) is satisfied, the ADP
seat and steering wheel return from exiting position to the previous driving position.
NOTE:
This function is set to OFF before delivery (initial setting).
K
Further information for the system setting procedure. Refer to Owners Manual.
OPERATION PROCEDURE
1.
2.
OPERATION CONDITION
Satisfy all of the following items. The entry assist function is not performed if these items are not satisfied.
Item
Request status
O
OFF
(Not operated)
P position
DETAIL FLOW
ADP-23
2008 QX56
Input
Output
Driver seat control unit receives the signals of ignition switch signal
and front door switch from BCM via CAN communication.
Door switch/Ignition
switch
2
Sensors (sliding, tilt)
Driver seat control unit operates the sliding motor when the operating
conditions are satisfied. Driver seat control unit then requests the operation of the tilt motor to the automatic drive positioner control unit
via UART communication. The automatic drive positioner control unit
operates the motor for a constant amount.
Sensors monitor the operating positions of seat and steering wheel
and then stops the operation of each motor when each part reaches
the recorded address.
INFOID:0000000001735428
ALJIA0235ZZ
1.
A. Steering column
B. Key switch and ignition knob
switch M12
C. BCM M18, M19, M20 (view with
instrument panel removed)
3.
4.
6.
A. Door mirrror LH D4, RH D107
B. Front door switch LH B8
C. Front door lock assembly LH (key
cylinder switch) D14
7.
5.
ADP-24
2008 QX56
INFOID:0000000001735429
CONTROL UNITS
Item
Function
According to the ignition signal and front door switch LH signal from BCM,
Operates the seat sliding motor for a constant amount.
Driver seat control unit then requests the operation of the tilt motor to the automatic drive positioner control unit via UART communication.
BCM
Recognizes the following status and transmits it to the driver seat control unit via
CAN communication.
Front door LH: OPEN/CLOSE
Ignition switch position: ACC/ON
INPUT PARTS
Switches
F
Item
Function
Detect front door LH open/close status.
Sensors
Item
Function
Sliding sensor
Tilt sensor
OUTPUT PARTS
Item
Function
Sliding motor
Tilt motor
ADP
ADP-25
2008 QX56
INFOID:0000000001735430
The auto drive positioner system can be checked and diagnosed for component operation with CONSULT-III.
DIAGNOSTIC MODE
Diagnostic mode
[AUTO DRIVE POS.]
Description
WORK SUPPORT
SELF-DIAG RESULTS
Performs self-diagnosis for the auto drive positioner system and displays the results.
DATA MONITOR
Displays input signals transmitted from various switches and sensors to driver seat control unit in real time.
ACTIVE TEST
CONSULT-III Function
INFOID:0000000001735431
SELF-DIAGNOSIS RESULTS
Refer to ADP-123, "DTC Index".
DATA MONITOR
Monitor Item
SET SW
Unit
Main
Signals
Selection
From
Menu
ON/OFF
Contents
MEMORY SW1
ON/OFF
MEMORY SW2
ON/OFF
SLIDE SWFR
ON/OFF
SLIDE SWRR
ON/OFF
RECLN SWFR
ON/OFF
RECLN SWRR
ON/OFF
LIFT FR SWUP
ON/OFF
ON/OFF status judged from the lifting switch front (up) signal.
LIFT FR SWDN
ON/OFF
LIFT RR SWUP
ON/OFF
ON/OFF status judged from the lifting switch rear (up) signal.
LIFT RR SWDN
ON/OFF
ON/OFF
ON/OFF
ON/OFF
ON/OFF
ADP-26
2008 QX56
Main
Signals
Selection
From
Menu
Contents
ON/OFF
ON/OFF
TILT SW-UP
ON/OFF
TILT SW-DOWN
ON/OFF
Monitor Item
PEDAL SW-FR
ON/OFF
ON/OFF status judged from the pedal adjusting switch (forward) signal.
PEDAL SW-RR
ON/OFF
DETENT SW
ON/OFF
STARTER SW
ON/OFF
Ignition key switch ON (START, ON) /OFF (ACC, OFF) status judged from the ignition switch signal.
SLIDE PULSE
RECLN PULSE
LIFT FR PULSE
LIFT RR PULSE
ADP
MIR/SEN RH UD
MIR/SEN RH RL
MIR/SEN LH UD
MIR/SEN LH RL
PEDAL SEN
ACTIVE TEST
CAUTION:
When driving vehicle, do not perform active test.
O
Test item
Description
SEAT SLIDE
SEAT RECLINING
SEAT LIFTER FR
SEAT LIFTER RR
TILT MOTOR
MIRROR MOTOR RH
ADP-27
2008 QX56
Description
MIRROR MOTOR LH
MEMORY SW INDCTR
WORK SUPPORT
Work item
Content
Item
40 mm
80 mm
150 mm
ADP-28
ON
OFF
ON
OFF
2008 QX56
COMPONENT DIAGNOSIS
INFOID:0000000001735433
INFOID:0000000001735434
DTC Logic
DTC DETECTION LOGIC
D
DTC
U1000
Trouble diagnosis
name
CAN COMM CIRCUIT
Possible cause
Harness or connectors
(CAN communication line is
open or shorted)
1. STEP 1
G
2. STEP 2
Check Self diagnostic result with CONSULT-III.
Is the DTC detected?
YES >> Perform diagnosis procedure. Refer to ADP-29, "Diagnosis Procedure".
NO
>> INSPECTION END
Diagnosis Procedure
ADP
INFOID:0000000001735435
INFOID:0000000001735436
ADP-29
2008 QX56
INFOID:0000000001735437
DTC Logic
INFOID:0000000001735438
B2112
Trouble diagnosis
name
SEAT SLIDE
Possible cause
1. STEP 1
Turn ignition switch ON.
>> GO TO 2
2. STEP 2
Check Self diagnostic result with CONSULT-III.
Is the DTC detected?
YES >> Perform diagnosis procedure. Refer to ADP-30, "Diagnosis Procedure".
NO
>> INSPECTION END
NOTE:
First perform diagnosis for B2126 if B2126 is detected. Refer to ADP-40, "Diagnosis Procedure".
Diagnosis Procedure
INFOID:0000000001735439
2. CHECK COMPONENTS
Refer to ADP-71, "Component Function Check" and ADP-87, "Component Function Check".
>> INSPECTION END
ADP-30
2008 QX56
Description
INFOID:0000000001735440
DTC Logic
INFOID:0000000001735441
DTC No.
B2113
SEAT RECLINING
Possible cause
E
Driver seat control unit
1. STEP 1
Turn ignition switch ON.
>> GO TO 2
2.STEP 2
Diagnosis Procedure
ADP
INFOID:0000000001735442
2. CHECK COMPONENTS
Refer to ADP-73, "Component Function Check" and ADP-89, "Component Function Check".
O
ADP-31
2008 QX56
INFOID:0000000001735443
DTC Logic
INFOID:0000000001735444
B2114
Trouble diagnosis
name
SEAT LIFTER FR
Possible cause
The driver seat control unit detects the output of lifting motor (front) output terminal for 0.1 second or
Driver seat control unit
more even if the lifting switch is not input.
1. STEP 1
Turn ignition switch ON.
>> GO TO 2
2.STEP 2
Check Self diagnostic result with CONSULT-III.
Is the DTC detected?
YES >> Perform diagnosis procedure. Refer to ADP-32, "Diagnosis Procedure".
NO
>> INSPECTION END
NOTE:
First perform diagnosis for B2126 if B2126 is detected. Refer to ADP-40, "Diagnosis Procedure".
Diagnosis Procedure
INFOID:0000000001735445
2. CHECK COMPONENTS
Refer to ADP-75, "Component Function Check" and ADP-91, "Component Function Check".
>> INSPECTION END
ADP-32
2008 QX56
Description
INFOID:0000000001735446
DTC Logic
INFOID:0000000001735447
DTC No.
B2115
SEAT LIFTER RR
Possible cause
The driver seat control unit detects the output of lifting motor (rear) output terminal for 0.1 second or
Driver seat control unit
more even if the lifting switch is not input.
1. STEP 1
Turn ignition switch ON.
>> GO TO 2
2.STEP 2
Diagnosis Procedure
ADP
INFOID:0000000001735448
2. CHECK COMPONENTS
Refer to ADP-77, "Component Function Check" and ADP-93, "Component Function Check".
O
ADP-33
2008 QX56
INFOID:0000000001735449
DTC Logic
INFOID:0000000001735450
B2117
Trouble diagnosis
name
Possible cause
1. STEP 1
Turn ignition switch ON.
>> GO TO 2
2. STEP 2
Check Self diagnostic result with CONSULT-III.
Is the DTC detected?
YES >> Perform diagnosis procedure. Refer to ADP-34, "Diagnosis Procedure".
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000001735451
2. CHECK FUNCTION
1.
2.
Description
The pedal adjusting motor is activated by receiving the drive signal.
ADP-34
2008 QX56
C
ALJIA0195ZZ
H
Connector
Terminals
(+)
(-)
37
M34
Ground
45
Condition
Voltage (V)
(Approx.)
Battery voltage
PIIA4806E
ADP
Battery voltage
ADP-35
2008 QX56
INFOID:0000000001754036
DTC Logic
INFOID:0000000001754037
B2118
Trouble diagnosis
name
TILT SENSOR
Possible cause
1. STEP 1
Turn ignition switch ON.
>> GO TO 2
2. STEP 2
Check Self diagnostic result with CONSULT-III.
Is the DTC detected?
YES >> Perform diagnosis procedure. Refer to ADP-36, "Diagnosis Procedure".
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000001754038
Condition
Tilt position
Value
Top
2V
Bottom
4V
2.CHECK FUNCTION
ADP-36
2008 QX56
Connector
M33
Terminals
(+)
(-)
Ground
Condition
Voltage (V)
(Approx.)
OK or NG
OK
>> Tilt sensor circuit is OK.
NG
>> GO TO 3
C
LIIA0485E
7-3
33 - 2
41 - 4
3.
OK or NG
OK
>> Replace tilt motor. Refer to ST-18, "Removal and Installation".
NG
>> Repair or replace harness.
ADP
K
LIIA1432E
1. Connect automatic drive positioner control unit connector and tilt sensor.
2. Turn ignition switch ON.
3. Check door mirror operation with memory function.
Is the operation normal?
YES >> Replace tilt sensor. Refer to ST-18, "Removal and Installation".
NO
>> GO TO 5
ADP-37
2008 QX56
INFOID:0000000001735452
DTC Logic
INFOID:0000000001735453
B2120
Trouble diagnosis
name
Possible cause
1. STEP 1
Turn ignition switch ON.
>> GO TO 2
2. STEP 2
Check Self diagnostic result with CONSULT-III.
Is the DTC is detected?
YES >> Perform diagnosis procedure. Refer to ADP-38, "Diagnosis Procedure".
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000001735454
Condition
Pedal position
Value
Forward
0.5V
Backward
4.5V
ADP-38
2008 QX56
G
LIIA1003E
ADP
ADP-39
2008 QX56
B2126 DETENT SW
< COMPONENT DIAGNOSIS >
B2126 DETENT SW
Description
INFOID:0000000001735455
Park position switch is installed on A/T device. It is turned OFF when the A/T selector lever is in P position.
The driver seat control unit judges that the A/T selector lever is in P position if continuity does not exist in this
circuit.
DTC Logic
INFOID:0000000001735456
B2126
Trouble diagnosis
name
DETENT SW
Possible cause
Harness and connectors
(Park position switch circuit is
opened/shorted.)
Park position switch
Combination meter
(CAN communication )
1. STEP 1
Drive the vehicle at 74km/h or more.
>> GO TO 2
2. STEP 2
Check Self diagnostic result with CONSULT-III.
Is the DTC detected?
YES >> Perform diagnosis procedure. Refer to ADP-40, "Diagnosis Procedure".
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000001735457
1. CHECK DTC
Check Self diagnostic result for BCM with CONSULT-lll.
Are other DTCs detected?
YES >> Check The DTC.
NO
>> GO TO 2
Condition
A/T selector lever
Status
P position
OFF
ON
ADP-40
2008 QX56
B2126 DETENT SW
< COMPONENT DIAGNOSIS >
1. Turn ignition switch OFF.
2. Disconnect A/T device and driver seat control unit.
3. Check continuity between A/T device connector M203 terminal 6
and driver seat control unit connector B203 terminal 21.
6 - 21
4.
Condition
6
Continuity
P position
Yes
No
H
LIIA1491E
ADP
ADP-41
2008 QX56
INFOID:0000000001735458
Driver seat control unit performs UART communication with the automatic drive positioner control unit using 2
communication lines, TX and RX line. Driver seat control unit receives the operation signals of pedal adjusting
switch, door mirror remote control switch, set switch and memory switch and the position signals of adjustable
pedal sensor and door mirror sensor from the automatic drive positioner control unit and transmits the operation request signal.
DTC Logic
INFOID:0000000001735459
B2128
UART COMM
Possible cause
1. STEP 1
Turn ignition switch ON.
>> GO TO 2
2. STEP 2
Operate pedal adjusting switch for more than 2 seconds.
>> GO TO 3
3. PROCEDURE 3
Check Self diagnostic result with CONSULT-III.
Is the DTC detected?
YES >> Perform diagnosis procedure. Refer to ADP-42, "Diagnosis Procedure".
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000001735460
4.
Terminal
1
17
Terminal
10
26
Continuity
Yes
PIIA4598E
Check continuity between driver seat control unit harness connector and ground.
ADP-42
2008 QX56
Terminal
1
Continuity
Ground
No
17
ADP
ADP-43
2008 QX56
INFOID:0000000001735461
INFOID:0000000001735462
INFOID:0000000001735463
NOTE:
Do not disconnect the battery negative terminal and the driver seat control unit connector until DTC is confirmed with CONSULT-III.
Terminal
B202
6
33
B203
()
Ground
40
Power
source
Condition
START
power supply
Ignition
switch
START
Battery
power supply
Ignition
switch
OFF
Voltage (V)
(Approx.)
LIIA1897E
Battery
voltage
Terminal
B202
32
B203
48
Continuity
Ground
Yes
ADP-44
PIIA4542E
2008 QX56
INFOID:0000000001735464
NOTE:
Do not disconnect the battery negative terminal and the driver seat control unit connector until DTC is confirmed with CONSULT-III.
M33
G
Voltage (V)
(Approx.)
Terminal
()
H
34
Ground
39
Battery voltage
PIIA4543E
ADP
Terminals
(+)
Automatic drive positioner
control unit connector
Terminal
40
Continuity
Ground
Yes
48
M
PIIA4544E
ADP-45
2008 QX56
SLIDING SWITCH
< COMPONENT DIAGNOSIS >
SLIDING SWITCH
Description
INFOID:0000000001735467
Sliding switch is equipped to the power seat switch LH on the seat cushion side surface. The operation signal
is input to the driver seat control unit when the sliding switch is operated.
INFOID:0000000001735468
1. CHECK FUNCTION
1.
2.
Select SLIDE SW-FR, SLIDE SW-RR in Data monitor mode with CONSULT-III.
Check sliding switch signal under the following conditions.
Monitor item
Condition
SLIDE SW-FR
SLIDE SW-RR
Status
Operate
ON
Release
OFF
Operate
ON
Release
OFF
Diagnosis Procedure
INFOID:0000000001735469
Terminals
(+)
Condition
()
11
B202
Ground
Sliding
switch
26
Voltage (V)
(Approx.)
Operate
(backward)
Release
Battery
voltage
Operate
(forward)
Release
Battery
voltage
PIIA4577E
Terminal
11
26
Terminal
Continuity
7
1
Yes
LIIA1125E
ADP-46
2008 QX56
SLIDING SWITCH
< COMPONENT DIAGNOSIS >
4. Check continuity between driver seat control unit harness connector and ground.
A
Driver seat control unit
connector
Terminal
Continuity
Ground
11
B202
B
No
26
1.
2.
3.
Terminals
Ground
Battery voltage
(+)
11
B202
()
Voltage (V)
(Approx.)
26
PIIA4577E
ADP
Component Inspection
INFOID:0000000001735470
Condition
3
1
Continuity
Operate
Yes
Release
No
Operate
Yes
Release
No
P
LIIA1126E
ADP-47
2008 QX56
RECLINING SWITCH
< COMPONENT DIAGNOSIS >
RECLINING SWITCH
Description
INFOID:0000000001735471
Reclining switch is equipped to the power seat switch LH on the seat cushion side surface. The operation signal is input to the driver seat control unit when the reclining switch is operated.
INFOID:0000000001735472
1.CHECK FUNCTION
1.
2.
Select RECLN SW-FR, RECLN SW-RR in Data monitor mode with CONSULT-III.
Check reclining switch signal under the following conditions.
Monitor item
Condition
RECLN SW-FR
RECLN SW-RR
Status
Operate
ON
Release
OFF
Operate
ON
Release
OFF
Diagnosis Procedure
INFOID:0000000001735473
Terminals
(+)
12
B202
Ground
Voltage (V)
(Approx.)
Condition
()
Reclining
switch
27
Operate
(forward)
Release
Battery voltage
Operate
(backward)
Release
Battery voltage
PIIA4580E
4.
Terminal
12
27
Terminal
Continuity
9
10
Yes
Check continuity between driver seat control unit harness connector and ground.
ADP-48
LIIA1127E
2008 QX56
RECLINING SWITCH
< COMPONENT DIAGNOSIS >
Driver seat control unit
connector
Terminal
Ground
12
B202
Continuity
No
27
Terminals
(+)
12
B202
27
()
Voltage (V)
(Approx.)
Ground
Battery voltage
PIIA4580E
ADP
Component Inspection
INFOID:0000000001735474
N
Terminals
Power seat switch LH
Condition
Continuity
Reclining switch
(backward)
Operate
Yes
Release
No
10
Reclining switch
(forward)
Operate
Yes
Release
No
LIIA1128E
ADP-49
2008 QX56
INFOID:0000000001735475
Lifting switch (front) is equipped to the power seat switch LH on the seat cushion side surface. The operation
signal is input to the driver seat control unit when the lifting switch (front) is operated.
INFOID:0000000001735476
1. CHECK FUNCTION
1.
2.
Select LIFT FR SW-UP, LIFT FR SW-DN in DATA MONITOR mode with CONSULT-III.
Check lifting switch (front) signal under the following conditions.
Monitor item
Condition
LIFT FR SW-UP
LIFT FR SW-DN
Status
Operate
ON
Release
OFF
Operate
ON
Release
OFF
Diagnosis Procedure
INFOID:0000000001735477
Terminals
(+)
13
B202
Voltage (V)
(Approx.)
Condition
()
Ground
Lifting
switch
(front)
28
Operate
(down)
0V
Release
Battery
voltage
Operate (up)
0V
Release
Battery
voltage
PIIA4583E
Terminal
13
28
Terminal
Continuity
5
6
Yes
LIIA1129E
ADP-50
2008 QX56
Terminal
Continuity
Ground
13
B202
B
No
28
1.
2.
3.
Terminals
Ground
Battery voltage
(+)
13
B202
()
Voltage (V)
(Approx.)
28
PIIA4583E
ADP
Component Inspection
INFOID:0000000001735478
Condition
3
6
Continuity
Operate
Yes
Release
No
Operate
Yes
Release
No
P
LIIA1130E
ADP-51
2008 QX56
INFOID:0000000001735479
Lifting switch (rear) is equipped to the power seat switch LH on the seat cushion side surface. The operation
signal is inputted to the driver seat control unit when the lifting switch (rear) is operated.
INFOID:0000000001735480
1. CHECK FUNCTION
1.
2.
Select LIFT RR SW-UP, LIFT RR SW-DN in Data monitor mode with CONSULT-III.
Check lifting switch (rear) signal under the following conditions.
Monitor item
Condition
LIFT RR SW-UP
LIFT RR SW-DN
Status
Operate
ON
Release
OFF
Operate
ON
Release
OFF
Diagnosis Procedure
INFOID:0000000001735481
Terminals
(+)
14
B202
Voltage (V)
(Approx.)
Condition
()
Lifting
switch
(rear)
Ground
29
Operate (down)
Release
Battery voltage
Operate (up)
Release
Battery voltage
PIIA4586E
4.
Terminal
14
29
Terminal
Continuity
8
2
Yes
Check continuity between driver seat control unit harness connector and ground.
ADP-52
LIIA1131E
2008 QX56
Terminal
Ground
14
B202
Continuity
No
29
Terminals
14
B202
()
Voltage (V)
(Approx.)
Ground
Battery voltage
(+)
29
PIIA4586E
ADP
Component Inspection
INFOID:0000000001735482
Condition
Continuity
Operate
Yes
Release
No
Operate
Yes
P
LIIA1132E
Release
No
ADP-53
2008 QX56
TILT SWITCH
< COMPONENT DIAGNOSIS >
TILT SWITCH
Description
INFOID:0000000001754039
ADP steering switch is equipped to the steering column. The operation signal is input to the automatic drive
positioner control unit when the ADP steering switch is operated.
INFOID:0000000001754040
1.CHECK FUNCTION
1.
2.
Select TILT SW-UP, TILT SW-DN in Data monitor mode with CONSULT-III.
Check tilt switch signal under the following conditions.
Monitor item
Condition
TILT SW-UP
TILT SW-DN
Status
Operate
ON
Release
OFF
Operate
ON
Release
OFF
Diagnosis Procedure
INFOID:0000000001754041
Connector
Terminals
(+)
1
M33
Ground
17
Condition
Voltage (V)
(Approx.)
(-)
LIIA0491E
3.
ADP-54
LIIA1434E
2008 QX56
TILT SWITCH
< COMPONENT DIAGNOSIS >
1 - Ground
17 - Ground
OK or NG
OK
>> GO TO 3
NG
>> Repair or replace harness.
Check continuity between ADP steering switch connector M16 terminal 1 and ground.
1 - Ground
OK or NG
OK
>> Check the condition of the harness and connector.
NG
>> Replace or replace harness.
F
LIIA0490E
ADP
Component Inspection
INFOID:0000000001754042
L
Terminals
Condition
2
1
3
Continuity
Yes
No
Yes
No
OK or NG
OK
>> INSPECTION END
NG
>> Replace ADP steering switch.
N
LIIA1435E
ADP-55
2008 QX56
INFOID:0000000001735483
Pedal adjusting switch is on the instrument panel. The operation signal is input to the driver seat control unit
when the pedal adjusting switch is operated. The pedal adjusting switch signal is sent to the automatic drive
positioner control unit via UART communication.
INFOID:0000000001735484
1. CHECK FUNCTION
1.
2.
Select PEDAL SW-FR, PEDAL SW-RR in Data monitor mode with CONSULT-III.
Check pedal adjusting switch signal under the following conditions.
Monitor item
Condition
PEDAL SW-FR
PEDAL SW-RR
Status
Operate
ON
Release
OFF
Operate
ON
Release
OFF
Diagnosis Procedure
INFOID:0000000001735485
Terminals
(+)
()
Condition
15
B202
Ground
30
Pedal adjusting
switch
Voltage (V)
(Approx.)
Operate
(backward)
Release
Battery
voltage
Operate
(forward)
Release
Battery
voltage
PIIA4591E
ADP-56
2008 QX56
B
Driver seat
control unit
connector
Pedal adjusting
switch connector
Terminal
15
B202
Terminal
M96
30
Continuity
Yes
LIIA0726E
4.
Check continuity between driver seat control unit harness connector and ground.
Driver seat control unit
connector
Terminal
Continuity
Ground
15
B202
No
30
Terminals
(+)
15
30
()
Voltage (V)
(Approx.)
Ground
Battery voltage
ADP
PIIA4591E
Check continuity between pedal adjusting switch connector M96 terminal 1 and ground.
1 - Ground
LIIA1015E
ADP-57
2008 QX56
Component Inspection
INFOID:0000000001735486
Condition
Continuity
Operate
Yes
Release
No
Operate
Yes
Release
No
LIIA1014E
ADP-58
2008 QX56
Description
INFOID:0000000001735487
Memory switch is equipped on the seat memory switch installed to the front door LH trim. The operation signal
is input to the automatic drive positioner control unit when the memory switch is operated.
INFOID:0000000001735488
1. CHECK FUNCTION
1.
2.
Select MEMORY SW 1, MEMORY SW 2, "SET SW" in Data monitor mode with CONSULT-III.
Check seat memory switch signal under the following conditions.
Monitor item
Condition
MEMORY SW1
Memory switch 1
MEMORY SW2
Memory switch 2
SET SW
Set switch
Diagnosis Procedure
Push
ON
Release
OFF
Push
ON
Release
OFF
Push
ON
Release
OFF
H
INFOID:0000000001735489
Automatic drive
positioner control
unit connector
Terminal
Seat memory
switch connector
Terminal
9
M33
ADP
Continuity
24
D5
25
4.
Status
1.
2.
PIIA4576E
Yes
Check continuity between automatic drive positioner control unit harness connector and ground.
N
Automatic drive positioner
control unit connector
Terminal
9
M33
Continuity
Ground
24
No
25
ADP-59
2008 QX56
Terminal
D5
Ground
Continuity
Yes
Component Inspection
INFOID:0000000001735490
Condition
Memory switch 1
Memory switch 2
Set switch
Continuity
Push
Yes
Release
No
Push
Yes
Release
No
Push
Yes
Release
No
LIIA1020E
ADP-60
2008 QX56
CHANGEOVER SWITCH
CHANGEOVER SWITCH : Description
INFOID:0000000001735491
INFOID:0000000001735492
Check the operation on MIR CHNG SW-R or MIR CHNG SW-L in DATA MONITOR mode with CONSULT-III.
Refer to ADP-26, "CONSULT-III Function".
Is the inspection result normal?
YES >> Changeover switch function is OK.
NO
>> Refer to ADP-61, "CHANGEOVER SWITCH : Diagnosis Procedure".
Terminals
(+)
(-)
Terminal
Voltage (V)
(Approx.)
ADP
2
M33
Ground
18
RIGHT
LEFT
PIIA4767E
Automatic drive
positioner control
unit connector
M33 (A)
4.
Terminal
2
18
Terminal
Continuity
P
11
10
Yes
ALJIA0201ZZ
Check continuity between automatic drive positioner control unit connector and ground.
Automatic drive
positioner control
unit connector
INFOID:0000000001735493
ADP-61
2008 QX56
Terminal
Continuity
Ground
M33 (A)
No
18
Terminal
D10
Ground
Continuity
Yes
Terminal
2
18
(-)
Voltage (V)
(Approx.)
Ground
PIIA4767E
INFOID:0000000001735494
ADP-62
2008 QX56
Continuity
LEFT
Yes
No
RIGHT
Yes
No
ALJIA0190ZZ
MIRROR SWITCH
INFOID:0000000001735495
F
INFOID:0000000001735496
INFOID:0000000001735497
ADP
L
Terminals
(+)
Automatic drive
positioner control
unit connector
Terminal
4
M33
Mirror switch
Condition
()
Ground
19
20
Voltage (V)
(Approx.)
UP
LEFT
DOWN
RIGHT
PIIA4771E
ADP-63
2008 QX56
Terminal
Terminal
15
M33 (A)
19
ALJIA0191ZZ
13
D10 (B)
Yes
12
20
4.
Continuity
Check continuity between automatic drive positioner control unit connector and ground.
Automatic drive positioner
control unit connector
Terminal
Continuity
3
4
M33 (A)
Ground
No
19
20
Terminal
D10
Ground
Continuity
Yes
Terminal
(-)
Voltage (V)
(Approx.)
3
M33
4
19
PIIA4771E
Ground
20
ADP-64
2008 QX56
INFOID:0000000001735498
Terminal
Door mirror remote
control switch
4
13
7
15
12
Continuity
RIGHT
Yes
No
LEFT
Yes
No
UP
Yes
No
DOWN
Yes
No
ALJIA0192ZZ
ADP
ADP-65
2008 QX56
INFOID:0000000001735499
Terminal
B208
32
Ground
Continuity
Yes
ADP-66
LIIA1133E
2008 QX56
DETENTION SWITCH
< COMPONENT DIAGNOSIS >
DETENTION SWITCH
Description
INFOID:0000000001735500
Park position switch is installed on A/T device. It is turned OFF when the A/T selector lever is in P position.
The driver seat control unit judges that the A/T selector lever is in P position if continuity does not exist in this
circuit.
INFOID:0000000001735501
1. CHECK FUNCTION
1.
2.
Condition
DETENT SW
Status
P position
OFF
Other than
above
ON
Diagnosis Procedure
G
INFOID:0000000001735502
ADP
B202
Terminal
(+)
21
(-)
Ground
Voltage (V)
(Approx.)
Condition
P position
Battery voltage
Other than
above
0V
M
ALJIA0193ZZ
ADP-67
2008 QX56
DETENTION SWITCH
< COMPONENT DIAGNOSIS >
1. Turn ignition switch OFF.
2. Disconnect driver seat control unit and A/T device.
3. Check continuity between driver seat control unit harness connector (A) and A/T device harness connector (B).
A
4.
Connector
Terminal
Connector
Terminal
B202
21
M203
Continuity
Yes
Check continuity between driver seat control unit harness connector (A) and ground.
A
Connector
Terminal
B202
21
ALJIA0194ZZ
Continuity
Ground
No
ADP-68
2008 QX56
Description
INFOID:0000000001735503
INFOID:0000000001735504
1. CHECK FUNCTION
1.
2.
Condition
DOOR SW-DR
Status
Open
ON
Close
OFF
Diagnosis Procedure
F
INFOID:0000000001735505
Disconnect BCM.
Check continuity between BCM connector and front door switch
LH connector.
BCM connector
Terminal
Terminal
Continuity
M19
47
B8
Yes
3.
ADP
Terminal
M19
47
Ground
Continuity
LIIA1027E
No
Component Inspection
P
INFOID:0000000001735506
ADP-69
2008 QX56
Ground part of
door switch
Condition
Front door switch
LH
Continuity
Pushed
No
Released
Yes
LIIA2377E
ADP-70
2008 QX56
SLIDING SENSOR
< COMPONENT DIAGNOSIS >
SLIDING SENSOR
Description
INFOID:0000000001735507
INFOID:0000000001735508
1. CHECK FUNCTION
1.
2.
Condition
SLIDE PULSE
Seat sliding
Valve
Operate (forward)
Change (increase)
Operate (backward)
Change (decrease)
Release
No change
Diagnosis Procedure
G
INFOID:0000000001735509
ADP
Terminals
(+)
Drivers
seat
control
unit
Terminal
()
Condition
Voltage signal
PIIA4556E
Operate
B202
24
Ground
Seat
sliding
PIIA3277E
Other
than
above
0 or 5
ADP-71
2008 QX56
SLIDING SENSOR
< COMPONENT DIAGNOSIS >
1. Turn ignition switch OFF.
2. Disconnect driver seat control unit and sliding motor LH.
3. Check continuity between driver seat control unit harness connector and sliding motor LH harness connector.
Driver seat control
unit connector
Terminal
Sliding motor
LH connector
16
B202
Continuity
24
B204
31
4.
Terminal
Yes
LIIA0706E
Check continuity between driver seat control unit harness connector and ground.
Driver seat control unit
connector
Terminal
16
B202
Continuity
Ground
24
No
31
ADP-72
2008 QX56
RECLINING SENSOR
< COMPONENT DIAGNOSIS >
RECLINING SENSOR
Description
INFOID:0000000001735510
INFOID:0000000001735511
1. CHECK FUNCTION
1.
2.
Condition
RECLN PULSE
Seat reclining
Value
Operate (forward)
Change (increase)
Operate (backward)
Change (decrease)
Release
No change
Diagnosis Procedure
G
INFOID:0000000001735512
Terminals
ADP
(+)
Driver
seat control unit
Terminal
()
Condition
Voltage signal
PIIA4559E
B202
Ground
Seat
reclining
Operate
M
SIIA0692J
Other
than
above
N
0 or 5
ADP-73
2008 QX56
RECLINING SENSOR
< COMPONENT DIAGNOSIS >
1. Turn ignition switch OFF.
2. Disconnect driver seat control unit and reclining motor LH.
3. Check continuity between driver seat control unit harness connector and reclining motor LH harness connector.
Driver seat control
unit connector
B202
4.
Reclining motor
connector
Terminal
9
Continuity
B205
31
Terminal
Yes
Check continuity between driver seat control unit harness connector and ground.
Terminal
9
LIIA0707E
Continuity
Ground
No
31
ADP-74
2008 QX56
Description
INFOID:0000000001735513
The lifting sensor (front) is installed to the seat slide cushion frame.
The pulse signal is input to the driver seat control unit when the lifting (front) is operated.
The driver seat control unit counts the pulse and calculates the lifting (front) amount of the seat.
INFOID:0000000001735514
1.CHECK FUNCTION
1.
2.
Condition
LIFT FR PULSE
Value
Operate (up)
Change (increase)
Operate (down)
Change (decrease)
Release
No change
Diagnosis Procedure
G
INFOID:0000000001735515
ADP
Terminals
(+)
Driver
seat control unit
connector
Terminal
()
Condition
Voltage signal
PIIA4561E
B202
25
Ground
Seat
lifting
(front)
Operate
SIIA0691J
Other
than
above
0 or 5
ADP-75
2008 QX56
Terminal
B202
25
Lifting motor
(front) connector
16
Continuity
3
B206
31
4.
Terminal
Yes
LIIA0708E
Check continuity between driver seat control unit harness connector and ground.
Terminal
16
B202
Continuity
Ground
25
No
31
ADP-76
2008 QX56
Description
INFOID:0000000001735516
The lifting sensor (rear) is installed to the seat slide cushion frame.
The pulse signal is input to the driver seat control unit when the lifting (rear) is operated.
The driver seat control unit counts the pulse and calculates the lifting (rear) amount of the seat.
INFOID:0000000001735517
1. CHECK FUNCTION
1.
2.
Condition
LIFT RR PULSE
Value
Operate (up)
Change (increase)
Operate (down)
Change (decrease)
Release
No change
Diagnosis Procedure
G
INFOID:0000000001735518
ADP
Terminals
(+)
Driver
seat control unit
connector
Terminal
()
Condition
Voltage signal
PIIA4563E
B202
10
Ground
Seat
lifting
(rear)
Operate
SIIA0693J
Other
than
above
0 or 5
ADP-77
2008 QX56
Terminal
B202
16
Terminal
B207
10
31
4.
Continuity
Yes
LIIA0709E
Check the continuity between driver seat control unit harness connector and ground.
Driver seat control unit
connector
Terminal
10
B202
Continuity
Ground
16
No
31
ADP-78
2008 QX56
TILT SENSOR
< COMPONENT DIAGNOSIS >
TILT SENSOR
Description
INFOID:0000000001754043
INFOID:0000000001754044
1. CHECK FUNCTION
1.
2.
Condition
TILT SEN
Value
Change between
1.2 V (Close to top)
3.4 V (Close to bottom)
Tilt position
Diagnosis Procedure
G
INFOID:0000000001754045
Connector
M33
Terminals
(+)
(-)
Ground
Condition
ADP
Voltage (V)
(Approx.)
LIIA0485E
ADP-79
2008 QX56
TILT SENSOR
< COMPONENT DIAGNOSIS >
1. Disconnect automatic drive positioner control unit and tilt sensor.
2. Check continuity between automatic drive positioner connector
M33, M34 terminals 7, 33, 41 and tilt sensor connector M69 terminals 2, 3, 4.
7-3
33 - 2
41 - 4
3.
OK or NG
OK
>> Replace motor. Refer to ST-18, "Removal and Installation".
NG
>> Repair or replace harness.
LIIA1432E
ADP-80
2008 QX56
Description
INFOID:0000000001735519
INFOID:0000000001735520
1. CHECK FUNCTION
1.
2.
Condition
PEDAL SEN
Pedal position
E
Value
Forward
0.5V
Backward
4.5V
Diagnosis Procedure
INFOID:0000000001735521
ADP
Terminal
(+)
Automatic
drive positioner control unit
Terminal
M33
(-)
Condition
Voltage (V)
(Approx.)
L
8
Ground
Pedal assembly
position
Forward
0.5
Backward
4.5
PIIA4569E
ADP-81
2008 QX56
Terminal
M33
M34
4.
Pedal adjusting
sensor connector
Terminal
Continuity
33
E110
41
Yes
Terminal
M33
M34
Continuity
Ground
33
No
LIIA1003E
41
ADP-82
2008 QX56
MIRROR SENSOR
< COMPONENT DIAGNOSIS >
MIRROR SENSOR
DRIVER SIDE
DRIVER SIDE : Description
INFOID:0000000001735522
INFOID:0000000001735523
1. CHECK FUNCTION
1.
2.
Condition
MIR/SEN LH U-D
Door mirror LH
MIR/SEN LH R-L
E
Value
Close to peak
3.4V
Close to valley
0.6V
3.4V
0.6V
INFOID:0000000001735524
ADP
Terminals
(+)
Door mirror
LH connector
Terminal
7
D4
Ground
8
Voltage (V)
(Approx.)
Condition
()
Door
mirror
LH
Close to peak
3.4
Close to valley
0.6
3.4
0.6
LIIA1482E
ADP-83
2008 QX56
MIRROR SENSOR
< COMPONENT DIAGNOSIS >
1. Turn ignition switch OFF.
2. Disconnect automatic drive positioner control unit and door mirror LH connector.
3. Check continuity between automatic drive positioner control unit
harness connector and door mirror LH harness connector.
Automatic drive
positioner control
unit connector
Door mirror LH
connector
M33
4.
Terminal
Terminal
7
D4
22
Continuity
Yes
LIIA1484E
Check continuity between automatic drive positioner control unit harness connector and ground.
Automatic drive positioner
control unit connector
Terminal
Continuity
Ground
M33
No
22
33
M34
2.
Terminal
41
Door mirror LH
connector
Terminal
Continuity
D4
Yes
Terminal
33
LIIA1483E
Continuity
Ground
No
41
ADP-84
2008 QX56
MIRROR SENSOR
< COMPONENT DIAGNOSIS >
PASSENGER SIDE
A
INFOID:0000000001735525
C
INFOID:0000000001735526
1.CHECK FUNCTION
1.
2.
Condition
MIR/SEN RH U-D
Door mirror RH
MIR/SEN RH R-L
Value
Close to peak
3.4V
Close to valley
0.6V
3.4V
0.6V
INFOID:0000000001735527
ADP
Terminals
(+)
Door mirror
RH connector
Terminal
()
Voltage (V)
(Approx.)
Condition
L
7
D107
Close to peak
3.4
Close to valley
0.6
3.4
0.6
LIIA1485E
Ground
Door mirror
RH
ADP-85
2008 QX56
MIRROR SENSOR
< COMPONENT DIAGNOSIS >
1. Turn ignition switch OFF.
2. Disconnect automatic drive positioner control unit and door mirror RH.
3. Check continuity between automatic drive positioner control unit
harness connector and door mirror RH harness connector.
Automatic drive positioner control unit
connector
Terminal
5
M33
4.
Door mirror RH
connector
Terminal
7
D107
21
Continuity
Yes
LIIA1473E
Check continuity between automatic drive positioner control unit harness connector and ground.
Terminal
Ground
M33
Continuity
No
21
Terminal
M34
2.
Door mirror RH
connector
33
Terminal
5
D107
41
Continuity
Yes
Terminal
33
LIIA1486E
Continuity
Ground
No
41
ADP-86
2008 QX56
SLIDING MOTOR
< COMPONENT DIAGNOSIS >
SLIDING MOTOR
Description
INFOID:0000000001735528
INFOID:0000000001735529
1. CHECK FUNCTION
1.
2.
Description
OFF
SEAT SLIDE
Stop
FR
Seat sliding
Forward
RR
Backward
Diagnosis Procedure
G
INFOID:0000000001735530
ADP
Terminal
(+)
Driver seat
control unit
connector
Terminal
Voltage (V)
(Approx.)
Test Item
(-)
PIIA4801E
OFF
35
B203
FR (forward)
Ground
42
SEAT
SLIDE
Battery voltage
RR (backward)
OFF
FR (forward)
RR (backward)
Battery voltage
ADP-87
2008 QX56
SLIDING MOTOR
< COMPONENT DIAGNOSIS >
1. Turn ignition switch OFF.
2. Disconnect driver seat control unit and sliding motor LH.
3. Check continuity between driver seat control unit harness connector and sliding motor LH harness connector.
Driver seat control
unit connector
B203
4.
Sliding motor LH
connector
Terminal
35
Continuity
B204
42
Terminal
Yes
Check continuity between driver seat control unit harness connector and ground.
Driver seat control
unit connector
B203
Terminal
35
LIIA0696E
Continuity
Ground
No
42
ADP-88
2008 QX56
RECLINING MOTOR
< COMPONENT DIAGNOSIS >
RECLINING MOTOR
Description
INFOID:0000000001735531
INFOID:0000000001735532
1. CHECK FUNCTION
1.
2.
Description
OFF
SEAT RECLINING
Stop
FR
Seat reclining
RR
Forward
Backward
Diagnosis Procedure
G
INFOID:0000000001735533
ADP
Terminal
(+)
Driver
seat control unit
connector
Terminal
(-)
Voltage (V)
(Approx.)
Test Item
PIIA4802E
OFF
36
B203
FR (forward)
Ground
44
SEAT RECLINING
Battery voltage
RR (backward)
OFF
FR (forward)
RR (backward)
Battery voltage
ADP-89
2008 QX56
RECLINING MOTOR
< COMPONENT DIAGNOSIS >
1. Turn ignition switch OFF.
2. Disconnect driver seat control unit connector and recling motor
LH.
3. Check continuity between driver seat control unit harness connector and reclining motor harness connector.
Driver seat control
unit connector
Terminal
B203
4.
Reclining motor LH
connector
36
Continuity
B205
44
Terminal
Yes
LIIA0697E
Check continuity between driver seat control unit harness connector and ground.
Driver seat control unit
connector
B203
Terminal
36
Continuity
Ground
No
44
ADP-90
2008 QX56
Description
INFOID:0000000001735534
The lifting motor (front) is installed to the seat slide cushion frame.
The lifting motor (front) is activated with the driver seat control unit.
The lifter (front) is moved upward/downward by changing the rotation direction of lifting motor (front).
INFOID:0000000001735535
1. CHECK FUNCTION
1.
2.
Description
OFF
SEAT LIFTER FR
E
Stop
UP
DWN
Upward
Downward
Diagnosis Procedure
G
INFOID:0000000001735536
ADP
Terminal
(+)
Driver seat
control unit
connector
Terminal
Voltage (V)
(Approx.)
Test Item
(-)
PIIA4805E
37
B203
Ground
45
SEAT
LIFTER
FR
OFF
UP
DWN (down)
Battery voltage
OFF
UP
Battery voltage
DWN (down)
ADP-91
2008 QX56
Terminal
B203
4.
37
Terminal
6
B206
45
Continuity
Yes
LIIA0698E
Check continuity between driver seat control unit harness connector and ground.
Driver seat control unit
connector
B203
Terminal
37
Continuity
Ground
No
45
ADP-92
2008 QX56
Description
INFOID:0000000001735537
The lifting motor (rear) is installed to the seat slide cushion frame.
The lifting motor (rear) is activated with the driver seat control unit.
The seat lifter (rear) is moved upward/downward by changing the rotation direction of lifting motor (rear).
INFOID:0000000001735538
1. CHECK FUNCTION
1.
2.
Description
OFF
SEAT LIFTER RR
E
Stop
UP
DWN
Upward
Downward
Diagnosis Procedure
G
INFOID:0000000001735539
ADP
Terminal
(+)
Driver seat
control unit
connector
Terminal
(-)
Voltage (V)
(Approx.)
Test Item
PIIA4804E
OFF
38
B203
UP
Ground
39
SEAT
LIFTER
RR
Battery voltage
DWN (down)
OFF
UP
DWN (down)
Battery voltage
ADP-93
2008 QX56
Terminal
B203
3.
38
Continuity
B207
39
Terminal
Yes
Check continuity between driver seat control unit harness connector and ground.
Driver seat control unit
connector
B203
Terminal
38
LIIA0699E
Continuity
Ground
No
39
ADP-94
2008 QX56
TILT MOTOR
< COMPONENT DIAGNOSIS >
TILT MOTOR
Description
INFOID:0000000001754046
INFOID:0000000001754047
1.CHECK FUNCTION
1.
2.
Description
OFF
TILT MOTOR
E
Stop
UP
Steering tilt
DWN
Upward
Downward
Diagnosis Procedure
G
INFOID:0000000001754048
4.
ADP
LIIA1431E
OK or NG
OK
>> GO TO 2
NG
>> Repair or replace harness.
1.
2.
LIIA0482E
ADP-95
2008 QX56
TILT MOTOR
< COMPONENT DIAGNOSIS >
Connector
Terminals
(+)
(-)
35
M34
Ground
42
Condition
Voltage (V)
(Approx.)
Battery voltage
Battery voltage
OK or NG
OK
>> Replace tilt motor. Refer to ST-18, "Removal and Installation".
NG
>> GO TO 3
ADP-96
2008 QX56
Description
INFOID:0000000001735540
INFOID:0000000001735541
1. CHECK FUNCTION
1.
2.
Description
OFF
Stop
FR
RR
Forward
Backward
Diagnosis Procedure
INFOID:0000000001735542
ADP
Terminal
(+)
Automatic
drive positioner control unit
connector
Terminal
(-)
Test Item
Voltage
(V)
(Approx.)
PIIA4806E
37
M34
Ground
45
OFF
RR (backward)
FR (forward)
OFF
RR (backward)
FR (forward)
Battery
voltage
0
Battery
voltage
ADP-97
2008 QX56
3.
Terminal
37
45
Pedal adjusting
motor connector
E109 (B)
Terminal
Continuity
Yes
ALJIA0195ZZ
Check continuity between automatic drive positioner control unit harness connector and ground.
Terminal
37
Continuity
Ground
No
45
ADP-98
2008 QX56
Description
INFOID:0000000001735543
It makes mirror face operate from side to side and up and down with the electric power that automatic drive
positioner control unit supplies.
INFOID:0000000001735544
Diagnosis Procedure
INFOID:0000000001735545
Terminals
Door mirror
connector
Terminal
()
Voltage (V)
(Approx.)
I
UP
1
D4 (LH)
D107 (RH)
(+)
Battery voltage
LEFT
Ground
0
Battery voltage
ALJIA0196ZZ
0
Battery voltage
ADP
Door mirror LH
Automatic drive
positioner control
unit connector
O
Terminal
Door mirror LH
connector
16
M33
31
32
Terminal
Continuity
3
D4
Yes
LIIA1880E
ADP-99
2008 QX56
Door mirror
RH connector
Terminal
14
M33
Continuity
15
D107
30
4.
Terminal
Yes
LIIA1888E
Door mirror LH
Terminal
16
M33
Continuity
Ground
31
No
32
Door mirror RH
Terminal
14
M33
Continuity
Ground
15
No
30
Terminals
(+)
Automatic drive
positioner control
unit connector
Terminal
(-)
Mirror switch
condition
Voltage (V)
(Approx.)
DOWN / RIGHT
Battery voltage
ALJIA0197ZZ
16
M33
31
32
Ground
UP
Battery voltage
0
Battery voltage
ADP-100
2008 QX56
Terminals
(+)
Automatic drive
positioner control unit connector
(-)
Terminal
C
UP
14
M33
Voltage (V)
(Approx.)
Battery voltage
15
LEFT
Ground
30
ALJIA0198ZZ
Battery voltage
0
Battery voltage
Component Inspection
INFOID:0000000001735546
ADP
M
Door mirror connector
D4 (LH)
D107 (RH)
Terminal
Operational direction
(+)
()
RIGHT
LEFT
UP
DOWN
O
ALJIA0199ZZ
ADP-101
2008 QX56
INFOID:0000000001735547
Memory switch is equipped on the seat memory switch installed to the driver side door trim. The operation
signal is inputted to the automatic drive positioner control unit when the memory switch is operated.
The status of automatic drive positioner system can be checked according to the illuminating/flashing status.
INFOID:0000000001735548
1. CHECK FUNCTION
1.
2.
Description
OFF
MEMORY SW INDCTR
OFF
ON-1
ON-2
Indicator 1: ON
Indicator 2: ON
Diagnosis Procedure
INFOID:0000000001735549
Automatic drive
positioner control
unit connector
M33
4.
Terminal
12
Terminal
6
D5
13
Continuity
Yes
LIIA1022E
Check continuity between automatic drive positioner control unit harness connector and ground.
Terminal
12
Continuity
Ground
No
13
ADP-102
2008 QX56
(+)
()
Voltage (V)
(Approx.)
D5
Ground
Battery voltage
C
PIIA4595E
Component Inspection
H
INFOID:0000000001735550
Continuity
(-)
5
Yes
L
ALJIA0200ZZ
ADP-103
2008 QX56
ECU DIAGNOSIS
DRIVER SEAT CONTROL UNIT
Reference Value
INFOID:0000000001735551
Monitor Item
Condition
SET SW
Set switch
MEMORY SW1
Memory switch 1
MEMORY SW2
Memory switch 2
SLIDE SWFR
SLIDE SWRR
RECLN SWFR
RECLN SWRR
LIFT FR SWUP
LIFT FR SWDN
LIFT RR SWUP
LIFT RR SWDN
Mirror switch
Mirror switch
Mirror switch
Mirror switch
Changeover switch
Changeover switch
PEDAL SW-FR
PEDAL SW-RR
Value/Status
Push
ON
Release
OFF
Push
ON
Release
OFF
Push
ON
Release
OFF
Operate
ON
Release
OFF
Operate
ON
Release
OFF
Operate
ON
Release
OFF
Operate
ON
Release
OFF
Operate
ON
Release
OFF
Operate
ON
Release
OFF
Operate
ON
Release
OFF
Operate
ON
Release
OFF
Up
ON
OFF
Down
ON
OFF
Right
ON
OFF
Left
ON
OFF
Right
ON
OFF
Left
ON
OFF
Forward
ON
OFF
Backward
ON
OFF
ADP-104
2008 QX56
Condition
DETENT SW
AT selector lever
STARTER SW
Ignition position
SLIDE PULSE
RECLN PULSE
LIFT FR PULSE
LIFT RR PULSE
MIR/SEN RH UD
P position
OFF
ON
Cranking
ON
Seat sliding
Seat reclining
MIR/SEN RH RL
MIR/SEN LH UD
MIR/SEN LH RL
PEDAL SEN
Pedal position
Value/Status
OFF
Forward
Backward
Forward
Backward
Up
Down
Up
Down
Close to peak
3.4
Close to valley
0.6
3.4
0.6
Close to peak
3.4
Close to valley
0.6
0.6
3.4
Forward
0.5
Backward
4.5
ADP
TERMINAL LAYOUT
L
LIIA2449E
PHYSICAL VALUES
ADP-105
2008 QX56
Wire
Color
Item
Condition
Voltage (V)
(Approx.)
PIIA4813E
CAN-H
L/R
Battery voltage
SIIA0692J
10
0 or 5
SIIA0693J
12
13
R/B
O/B
L/B
14
G/W
15
L/Y
0 or 5
0
Battery voltage
0
Battery voltage
0
Battery voltage
0
Battery voltage
0
Battery voltage
5
16
Ignition switch ON
17
PIIA4814E
ADP-106
2008 QX56
Wire
Color
19
Item
Condition
Voltage (V)
(Approx.)
CAN-L
L/R
Battery voltage
24
Y/G
PIIA3277E
0 or 5
25
LG
SIIA0691J
27
28
P/B
G/B
Y/B
29
R/W
30
31
L/Y
32
33
35
36
37
Battery voltage
0
ADP
Battery voltage
0
Battery voltage
0
Battery voltage
0
Battery voltage
Sensor ground
Ground
L/B
Battery voltage
V/W
Battery voltage
Y/G
BR
ADP-107
0 or 5
P
Battery voltage
0
Battery voltage
0
2008 QX56
Wire
Color
Item
38
B/W
39
40
Y/R
42
O/B
44
45
48
Y/R
GR
B/W
Condition
Voltage (V)
(Approx.)
Battery voltage
0
Battery voltage
0
Battery voltage
Battery voltage
Ground
ADP-108
0
Battery voltage
0
Battery voltage
0
0
2008 QX56
Wiring Diagram
INFOID:0000000001735552
ADP
AWJWA0010GB
ADP-109
2008 QX56
AWJWA0011GB
ADP-110
2008 QX56
ADP
O
AWJWA0012GB
ADP-111
2008 QX56
AWJWA0013GB
ADP-112
2008 QX56
ADP
O
AWJIA0039GB
ADP-113
2008 QX56
AWJIA0040GB
ADP-114
2008 QX56
ADP
O
AWJIA0041GB
ADP-115
2008 QX56
AWJIA0042GB
ADP-116
2008 QX56
ADP
O
AWJIA0043GB
ADP-117
2008 QX56
AWJIA0044GB
ADP-118
2008 QX56
ADP
O
AWJIA0045GB
ADP-119
2008 QX56
AWJIA0046GB
ADP-120
2008 QX56
ADP
O
AWJIA0047GB
ADP-121
2008 QX56
AWJIA0048GB
Fail Safe
INFOID:0000000001735553
The fail-safe mode may be activated if the following symptoms are observed.
FAIL-SAFE MODE
When any manual and automatic operations are not performed, if any motor operations of front seat LH or
pedals are detected for T2 or more, status is judged Output error.
ADP-122
2008 QX56
T2
Seat sliding
Seat reclining
Same as above
Same as above
Same as above
Pedal adjust
Same as above
NOTE:
The front seat LH position and pedal adjustment functions (see the following table) operate simultaneously in
the order of priority.
Priority
Function
Priority
Function
Seat lifter-FR
Pedal
Seat lifter-RR
Seat reclining
*: In conjunction with sliding the seat, the door mirrors are positioned.
DTC Index
INFOID:0000000001735554
H
CONSULT-III
display
Timing*1
Item
Reference page
Current malfunction
Previous malfunction
1-39
CAN communication
ADP-29
SEAT SLIDE
[B2112]
1-39
ADP-30
SEAT RECLINING
[B2113]
1-39
ADP-31
1-39
ADP-34
1-39
ADP-34
TILT MOTOR
[B2116]
1-39
ADP-95
1-39
ADP-34
TILT SENSOR
[B2118]
1-39
ADP-36
1-39
ADP-34
DETENT SW
[B2126]
1-39
ADP-40
UART COMM
[B2128]
1-39
UART communication
ADP-42
*1
ADP
ADP-123
2008 QX56
INFOID:0000000001735555
TERMINAL LAYOUT
LIIA2449E
PHYSICAL VALUES
Terminal
Wire Color
W/G
LG
Y/B
Item
Condition
Voltage (V)
(Approx.)
V/W
R/B
L/Y
Y/BR
BR/Y
LG/B
10
0.5
4.5
Memory switch 1 ON
PIIA4813E
12
Memory switch 1 ON
Battery voltage
ADP-124
2008 QX56
Wire Color
Item
13
Y/G
14
GR/R
15
V/R
O
Mirror motor LH RIGHT signal
17
18
G/B
BR/W
Condition
Voltage (V)
(Approx.)
Memory switch 2 ON
Battery voltage
0
1.5 - Battery voltage
0
1.5 - Battery voltage
0
1.5 - Battery voltage
19
SB
20
GR
21
L/W
22
24
G/O
25
P/L
Set switch 1 ON
Memory switch 2 ON
ADP
L
26
M
PIIA4814E
Y
Mirror motor RH RIGHT signal
31
0
1.5 - Battery voltage
0
32
BR
33
W/L
34
Y/R
Battery voltage
ADP-125
2008 QX56
Wire Color
35
37
39
Item
Condition
Voltage (V)
(Approx.)
Battery voltage
0
Battery voltage
0
L/B
Battery voltage
40
B/W
Ground
41
W/G
Sensor ground
Battery voltage
42
R
B
Ground
ADP-126
0
Battery voltage
0
0
2008 QX56
Wiring Diagram
INFOID:0000000001735556
ADP
AWJWA0010GB
ADP-127
2008 QX56
AWJWA0011GB
ADP-128
2008 QX56
ADP
O
AWJWA0012GB
ADP-129
2008 QX56
AWJWA0013GB
ADP-130
2008 QX56
ADP
O
AWJIA0039GB
ADP-131
2008 QX56
AWJIA0040GB
ADP-132
2008 QX56
ADP
O
AWJIA0041GB
ADP-133
2008 QX56
AWJIA0042GB
ADP-134
2008 QX56
ADP
O
AWJIA0043GB
ADP-135
2008 QX56
AWJIA0044GB
ADP-136
2008 QX56
ADP
O
AWJIA0045GB
ADP-137
2008 QX56
AWJIA0046GB
ADP-138
2008 QX56
ADP
O
AWJIA0047GB
ADP-139
2008 QX56
AWJIA0048GB
ADP-140
2008 QX56
Reference Value
INFOID:0000000001735557
Monitor Item
DOOR SW-DR
Condition
Value/Status
Off
On
TERMINAL LAYOUT
PHYSICAL VALUES
Wiring Diagram
INFOID:0000000001735558
INFOID:0000000001735559
For DTC priority information, refer to BCS-47, "DTC Inspection Priority Chart".
DTC Index
INFOID:0000000001735560
ADP
ADP-141
2008 QX56
SYMPTOM DIAGNOSIS
ADP SYSTEM SYMPTOMS
Symptom Table
INFOID:0000000001735561
NOTE:
Always perform the Basic Inspection before performing diagnosis in the following table. Refer to ADP-5,
"Work Flow".
SYMPTOM 1
Symptom
Diagnosis procedure
Reference
page
Sliding operation
ADP-46
Reclining operation
ADP-48
ADP-50
ADP-52
ADP-56
ADP-81
ADP-54
1. Changeover switch.
ADP-61
2. Mirror switch
ADP-63
ADP-66
Pedal operation
Steering wheel tilt operation
Door mirror operation
All parts of seat
SYMPTOM 2
Symptom
Diagnosis procedure
Reference
page
Sliding operation
ADP-71
Reclining operation
ADP-73
ADP-75
ADP-77
Pedal operation
ADP-81
ADP-79
Driver side:
ADP-83
Passenger
side:
ADP-85
SYMPTOM 3
Symptom
Memory functions and manual functions (for specific part) do not operate
Diagnosis procedure
Reference
page
Sliding operation
ADP-87
Reclining operation
ADP-89
ADP-91
ADP-93
Pedal operation
ADP-97
ADP-95
ADP-99
ADP-142
2008 QX56
Diagnosis procedure
Reference
page
ADP-20
2. Perform initialization.
ADP-22
ADP-69
SYMPTOM 5
Symptom
Memory indicators 1 and/or 2 do not illuminate.
Diagnosis procedure
Reference
page
ADP-59
ADP-102
SYMPTOM 6
F
Symptom
Memory operation does not operate.
Diagnosis procedure
Check A/T device (park position switch).
Reference
page
ADP-67
ADP
ADP-143
2008 QX56
INFOID:0000000001735562
The following symptoms are normal operations, and they do not indicate a malfunction.
Symptom
Action to take
Reference page
Cause
Perform initialization.
ADP-20
ADP-23
ADP-23
Memory function:
ADP-17
Memory function, entry/exit assist function or Intelligent Key interlock function does not
operate.
ADP-144
2008 QX56
PRECAUTIONS
< PRECAUTION >
PRECAUTION
PRECAUTIONS
Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT
PRE-TENSIONER"
INFOID:0000000001537293
The Supplemental Restraint System such as AIR BAG and SEAT BELT PRE-TENSIONER, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. This system includes seat belt switch inputs and dual stage front air bag modules. The SRS
system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front
air bag, depending on the severity of a collision and whether the front occupants are belted or unbelted.
Information necessary to service the system safely is included in the SR and SB section of this Service Manual.
WARNING:
To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in
the event of a collision which would result in air bag inflation, all maintenance must be performed by
an authorized NISSAN/INFINITI dealer.
Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal
injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag
Module, see the SR section.
Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this
Service Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or harness connectors.
INFOID:0000000001537294
When removing or disassembling each component, be careful not to damage or deform it. If a component
may be subject to interference, be sure to protect it with a shop cloth.
I
When removing (disengaging) components with a screwdriver or similar tool, be sure to wrap the component
with a shop cloth or vinyl tape to protect it.
Protect the removed parts with a shop cloth and keep them.
ADP
Replace a deformed or damaged clip.
If a part is specified as a non-reusable part, always replace it with new one.
Be sure to tighten bolts and nuts securely to the specified torque.
After re-installation is completed, be sure to check that each part works normally.
K
Follow the steps below to clean components.
- Water soluble foul: Dip a soft cloth into lukewarm water, and wring the water out of the cloth to wipe the
fouled area.
L
Then rub with a soft and dry cloth.
- Oily foul: Dip a soft cloth into lukewarm water with mild detergent (concentration: within 2 to 3%), and wipe
the fouled area.
Then dip a cloth into fresh water, and wring the water out of the cloth to wipe the detergent off. Then rub with M
a soft and dry cloth.
Do not use organic solvent such as thinner, benzene, alcohol, or gasoline.
For genuine leather seats, use a genuine leather seat cleaner.
N
ADP-145
2008 QX56
ON-VEHICLE MAINTENANCE
PRE-INSPECTION FOR DIAGNOSTIC
Basic Inspection
INFOID:0000000001735563
ADP-146
2008 QX56
7. CHECK MECHANISM
ADP
ADP-147
2008 QX56
PREPARATION
< PREPARATION >
PREPARATION
PREPARATION
Special Service Tool
INFOID:0000000001537295
The actual shapes of Kent-Moore tools may differ from those of special service tools illustrated here.
Tool number
(Kent-Moore No.)
Tool name
Description
Locating the noise
(J-39570)
Chassis ear
SIIA0993E
(J-43980)
NISSAN Squeak and Rattle
Kit
SIIA0994E
INFOID:0000000001537296
(Kent-Moore No.)
Tool name
Description
(J-39565)
Engine ear
SIIA0995E
ADP-148
2008 QX56
INFOID:0000000001536870
Refer to ACC-3, "Removal and Installation" and ADP-149, "Removal and Installation" .
C
ADP
ADP-149
2008 QX56