Академический Документы
Профессиональный Документы
Культура Документы
Test Method
English
Metric
Youngs Modulus
82 000 psi
565 MPa
Tensile Strength
2250 psi
15,5 MPa
Tensile Elongation
17 %
17 %
Charpy Impact,
notched
3,8 ft-lb/in2
8 kJ/m2
Brinell Hardness
20,5 HB
Maximum Load
49 N
482 - 500 F
250 260 C
257 F
125 C
234 F
112 C
Thermal Expansion
Minimal
Odor
Nearly odorless
Solubility
Insoluble in water
Hazards
The information presented are typical values intended for reference and comparison purposes only. They should not
be used for design specifications or quality control purposes. End-use material performance can be impacted(+/-)
by, but not limited to part design, end-use conditions, test conditions, etc. Actual values will vary with build conditions.
Tested parts were built on Zortrax M200 @ 0.2mm slice. Product specifications are subject to change without notice.
The performance characteristics of these materials may vary according to application, operating conditions, or enduse. Each user is responsible for determining that the Zortrax material is safe, lawful and technically suitable for the
inttended application, as well as for identifying the proper disposal (or recycling) method consistent with applicable
environmental laws and regulations. Zortrax makes no warranties of any kind, express or implied including but not
limited to the warranties of merchantability, fitness for a particular use.
*Due amorphous nature, material does not display a true melting point.
www.zortrax.com | 1
Test Report
Plastic samples supplied by the principal were tested to determine their toughness in a static tensile test, the Charpy
impact test and the Brinell hardness test.
1. Endurance Testing
Test was performed in accordance with DIN EN ISO 527-2 standard (ASTM D638). Dumbbell shaped specimens
that were used to perform these tests are shown in picture 1. The INSTRON model 4481 toughness testing machine
(made in UK) was used to perform the tests. Tests were carried out in room temperature. Samples were elongated
with the speed of 50 mm/ min. Test results are summarized in the table 1., detailed overview of the results can be
found in an annex.
No
SAMPLE
Youngs Modulus
[MPa]
564,69 12
Tensile Strength
[MPa]
Yield Strength
[MPa]
15,28 0,43
7,83 0,69
Breaking
Strength
[MPa]
14,11 2,11
Elongation at
Break
[%]
17,21 3,45
www.zortrax.com | 2
The score was calculated as an average of 10 calculated impacts, where also fractured samples were counted in as
approved (parts of which were still connected to each other with a thin layer of material after an impact). The impact
score was estimated from the following formula:
ak=
k
____
btk
103 , kJ/m2
Where: an stands for the energy used to break the sample, kJ; b,t thickness and width of a sample,
mm; tk sample thickness under the notch
Charpy Impact Test results are presented in table 2.
Sample
SAMPLE
www.zortrax.com | 3
Sample
SAMPLE
20,45 1,15
Contact
Office: office@zortrax.com
Sales Department: sales@zortrax.com
Support Center: support@zortrax.com
Wyszynskiego 1/219
10-457 Olsztyn, Poland
NIP: 7393864289
REGON: 281551179
2014, Zortrax sp. z o.o. All rights reserved. Zortrax, Zortrax M200, Z-ABS, Z-ULTRAT, Z-PCABS, Z-HIPS, Z-GLASS, Z-WOOD, Z-Suite, .zcode
are trademarks of Zortrax.
www.zortrax.com | 4