Академический Документы
Профессиональный Документы
Культура Документы
LIMITATION OF LIABILITY
THE INFORMATION IN THIS PUBLICATION IS BELIEVED TO
BE ACCURATE IN ALL RESPECTS, HOWEVER, WE CANNOT
ASSUME RESPONSIBILITY FOR ANY CONSEQUENCES
RESULTING FROM THE USE THEREOF. THE INFORMATION
CONTAINED HEREIN IS SUBJECT TO CHANGE WITHOUT
NOTICE. REVISIONS OR NEW EDITIONS TO THIS
PUBLICATION MAY BE ISSUED TO INCORPORATE SUCH
CHANGES.
- ii -
CAUTION:
CAUTION
PRECAUTIONS
Safety -----------------------------------------
Installation -----------------------------------
- iii -
CE COMPLIANCE STATEMENT
WARNING
This is a Class A product. In a domestic environment this product
may cause radio interference in which case the user may be required
to take adequate measures.
- iv -
IMPORTANT SAFEGUARDS
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with dry cloth.
7. Do not block any ventilation openings. Install in accordance with the
manufacturer's instructions.
8. Do not install near any heat sources such as radiators, heat registers,
stoves, or other apparatus (including amplifiers) that product heat..
9. Do not defeat the safety purpose of the polarized or grounding-type plug.
A polarized plug has two blades with one wider than the other.
A grounding type plug has two blades and a third grounding prong.
The wide blade or the third prong is provided for your safety. If the
provided plug does not fit into your outlet, consult an electrician for
replacement of the obsolete outlet.
10. Protect the power cord from being walked on or pinched particularly
at plugs, convenience receptacles, and the point where thy exit from the
apparatus.
11. Only use attachments/accessories specified by the manufacturer.
12. Unplug this apparatus during lightning storms or when unused for long
periods of time.
13. Refer all servicing to qualified service personnel. Servicing is required
when the apparatus has been damaged in any way, such as power-supply
cord or plug is damaged, liquid has been spilled or objects have fallen into
the apparatus, the apparatus has been exposed to rain or moisture, does
not operate normally, or has been dropped.
14. CAUTION - THESE SERVICING INSTRUCTIONS ARE FOR USE BY
QUALIFIED SERVICE PERSONNEL ONLY. TO REDUCE THE RISK
OF ELECTRIC SHOCK DO NOT PERFORM ANY SERVICING OTHER
THAN THAT CONTAINED IN THE OPERATING INSTRUCTIONS
UNLESS YOU ARE QUALIFIED TO DO SO.
-v-
TABLE OF CONTENTS
INTRODUCTION
CAMERA OVERVIEW
FUNCTION DESCRIPTION
CONNECTIONS
CONTENTS OF PACKAGE
8
10
11
12
SPECIFICATIONS
13
- vi -
INTRODUCTION
The camera provides high-quality images using SONY CCD technology
especially designed for closed-circuit television (CCTV) and security
surveillance applications.
Features:
High resolution and high performance 1/3" SONY Super HAD CCD
technology
Excellent picture quality
540 lines(Color) of resolution
0.25 Lux(Color) / 0.01 Lux(B/W) @ F1.2 Sensitivity (True D&N)
0.25 Lux(Color) @ F1.2 Sensitivity (Digital D/N)
C/CS, backfocus cam for easy adjustment
Auto electronic shutter [1/60(1/50) ~ 1/100,000] and manual electronic
Shutter modes
Auto Trace White balance modes
Selectable BLC function
Day & Night (True D&N / Digital D/N)
AGC (Auto Gain Control)
Video out(BNC)
Quick connect for video or DC lens with 4-pin connector
Operates in 100-240 VAC
CAMERA OVERVIEW
C Mount Ring (Option)
120.0mm
(C MOUNT LENS)
SIDE VIEW
1/4-20UNC
43.0mm
14.0mm
56.0mm
1-32UNEF
7.0mm
66.0mm
FRONT VIEW
TOP VIEW
FUNCTION DESCRIPTION
- SIDE VIEW
- REAR VIEW
1
1 IRIS LEVEL
AUTO
COLOR
D/N
2 FUNCTION SWITCH
3 AC Power Cord
4 POWER INDICATOR
5 VIDEO OUTPUT CONNECTOR
<DC12V>
1) IRIS LEVEL
Adjust the DC-type auto iris lens for an optimum picture using this volume.
2) FUNCTION SWITCH
- E/I (on/off)
When set to the ON position, the electronic iris switch automatically varies the
camera's shutter to mimic auto-iris control, allowing fixed or manual iris lenses to
be used in a wider range. When this switch is set to ON, turn the F/F switch OFF.
- FF (on/off)
This function is used for removing flicker, when camera signal format does not
coincide with power source frequency being used.
- BLC (on/off)
This on/off switch controls backlight compensation. When set to ON, the camera
will automatically try to maintain proper exposure in the specific area even if the
lighting level changes.
- AGC (on/off)
The auto gain control switch allows the video signals to maintain a constant level.
This switch is useful when using the camera at low-light levels and when lighting
levels change over time. For best low light conditions, this switch should set to ON.
- Day/Night (Auto/Color)
Use this switch to set the camera Day/Night mode Auto(ON) or Color(OFF)
Auto : D/N mode converse automatically (AGC must set to ON)
Color : Only Color
- A/I (DC/VIDEO)
Use this switch to set the auto iris type.
3) POWER INPUT TERMINAL
4) POWER INDICATOR
5) VIDEO OUTPUT CONNECTOR
CONNECTIONS
1) POWER INPUT TERMINAL
AC Power Cord - This power cord accepts a
100-240V ~ 50Hz +/- 1Hz
AC 100-240V
CONTENTS OF PACKAGE
Installation of the camera must be performed by qualified service personnel in
accordance with all local and national electrical and mechanical codes.
Carefully remove the color camera and its accessories from the carton
and verify that they were not damaged in shipment.
The contents of the package includes:
1. Color CCD camera
2. Mini-DIN connector (for video-or dc-type auto-iris lens)
3. This Manual
Rib
Pin 3
Automatic
Iris Lens
Pin 1
Heat
Pin 4
Shrinkable
Tubes
Iris Control
Pin 2
Cable
Connector
PIN
NAME
WIRE COLOR
Voltage +
Open
Red
_
Video
White
Ground
Black
2. Attach the video-type auto iris lens to the lens mount on the front of the
camera.
3. IMPORTANT: The minimum Plug the connector from the lens into the auto
iris jack on the side of the camera. The connector is polarized and can only
be inserted into the jack one way.
4. Apply power to the camera.
5. Set the E/I dip switch (rear side on the camera) to OFF position.
6. Set the A/I dip switch (rear side on the camera) to VIDEO position.
7. Adjust the focus ring on the lens for an optimum picture. If a picture is not
Visible, set the lens for proper exposure by adjusting the ALC (Automatic
Level Control) and the level on the lens. The ALC setting can range
between AVG (average) or PK (peak). A midrange setting is appropriate for
most applications.
To increase the speed of the lens reaction to the changing light, set
the lens adjustment to PK so the lens will adjust to the brightest or
peak object in the video. Use this setting if you want to see the
brightest object and not the background objects.
Rib
Pin 3
Automatic
Iris Lens
Pin 1
Heat
Pin 4
Shrinkable
Tubes
Iris Control
Pin 2
Cable
Connector
PIN
NAME
WIRE COLOR
Damp Coil -
Blue
Damp Coil +
Red
Drive Coil +
White
Drive Coil -
Green
side
10
11
AREA TO CHECK
PROBLEM
No video
Video but no
control
Dark Video
1. Adjust iris.
2. Check A/I connections.
PREVENTIVE MAINTENANCE
Preventive maintenance allows detection and correction of minor that faults
before they become serious and cause equipment failure.
Every three-month, perform the following maintenance.
1. Inspect all connection cables for deterioration or other damage.
2. Clean components with a clean damp cloth.
3. Verify that all the mounting hardware is secure.
12
SPECIFICATIONS
MODEL
Power
General
Connector
&
etc.
Power source
Power consumption
Image sensor
Total pixels
Scanning system
Scanning frequency
Sync. system
Electronic shutter
Resolution
True D&N
(NTSC)
(PAL)
100 - 240V
3.5 Watts
Digital D/N
(NTSC)
(PAL)
10%
3.0 Watts
13