Академический Документы
Профессиональный Документы
Культура Документы
Communication with remotely located automation systems is possible via the Internet. A physical communication port with a
network is required for this communication. An Ethernet interface can be used for that purpose.
Presented here is the design and implementation of an Ethernet interface for automation systems, using a microcontroller.
Ethernet is quite a complex interface, which was difficultto use with small microcontrollers having little memoryuntil Microchip
came up with ENC28J60 Ethernet chip. It is a small chip with only 28 pins that can be used as an Ethernet network interface for
any microcontroller equipped with serial peripheral interface (SPI).
Therefore Microchip opens a whole new world of applications like the one we have implemented in this project where real-time
readings of temperature and ambient light sensors placed at a remote place can be read using the Internet.
Fig. 1 shows the html page embedded in the source code of the automation system that provides these readings. The html
page can be accessed from a remote location. Distance is no longer a limiting factor. Even Wi-Fi connectivity is possible because
the devices can be connected to a wireless bridge too.
Communication with the host controller is implemented via SPI, with clock rates of up to 25 MHz. Two dedicated pins (LED A
and LED B) are used for LED link and network activity indication. Fig. 4 shows the simplifiedconnections scheme for easy
understanding.
The SPI pins of IC3 are directly interfaced with IC4 as shown in Fig. 4. In the interconnection circuit there is no conversion
required from 3.3 V to 5 V because the pins of IC4 are 5V tolerant.
Automation system. The heart of the system is ATmega128, which is an eight-bit microcontroller with 128 kB of in-system
programmable Flash with read-while-write capabilities, 4kB EEPROM, 4kB SRAM, 53 general-purpose input/output (I/O) lines,
32 general-purpose working registers, real-time counter (RTC), four flexibletimers/counters with compare modes and PWM, two
US-ARTs, a byte-oriented two-wire serial interface, an eight-channel, 10-bit analogue-to-digital converter (ADC) with optional
differential input stage with programmable gain, programmable watchdog timer with internal oscillator, an SPI serial port, IEEE
1149.1 standard-compliant JTAG test interface (also used for accessing the on-chip debug system and programming) and six
software-selectable power-saving modes.
Microcontroller IC3 continuously monitors temperature and light intensity using sensors IC5 and IC6, respectively. Both the
sensors communicate to the microcontroller via I2C protocol. Port pins PD0 and PD1 are used to interface both the sensors to
the microcontroller. Real-time readings from both the sensors are displayed on LCD1, which is interfaced to IC3 using pins PC4
through PC7 for data pins of LCD1 and pins PC0 through PC2 for control pins of LCD1. Temperature range can be defned in the
source code, within which LCD1 displays the message its normal temperature and green LEDs (LED5 and LED8) glow. If
temperature crosses the maximum of the range, the message on the display changes to its too hot and red LEDs (LED3 and
LED6) glow. In case temperature goes below the minimum limit, the message changes to its too cold and blue LEDs (LED4
and LED7) glow.
The triggering value for light intensity can also be definedin the source code. If the intensity of light goes below the
predefinedvalue, the relay connected through CON2 is driven by port pin PD7 of IC3 to switch on the bulb and the LCD shows
the message bulb on.
The power to the whole system is provided using a 12V adaptor. Regulator IC1 provides a 5V output, which is further regulated
by IC2 to 3.3 V.
Software
The program is written in C language. It is compiled and programmed into the target device using WinAVR. The html page
embedded in the source code can be accessed from a remote place to findout the readings of the temperature and light
sensors. The section of the program definingthe html page is shown in Fig. 5.
To access the system, you have to change the mac address and IP address corresponding to your network arrangement in the
line mentioned below in the source code:
static uint8_t mymac[6] = {0x54,0x90,
0x58,0x10,0x65,0x77};
The source code is compiled and programmed using WinAVR following the below mentioned steps:
1. Install WinAVR
2. Connect the programmer and check the COM port allotted to the device
3. Change the COM port in the make fileprovided together with the source code
4. Open command prompt and go to the directory where the program is saved
5. Type make clean and press enter
6. Then type make all and press enter
7. Finally, to program the microcontroller, type make program after connecting the programmer to the target board
Download: http://www.electronicsforu.com/electronicsforu/circuitarchives/my_documents/my_files/8DZ_Archive.zip
Construction and testing
Both the layers of an actual-size, double-side PCB are shown in Figs 6 and 7 while the component layout is shown in Fig. 8.
Assemble the circuit on a PCB as it saves time and minimises assembly errors. Carefully assemble the components and doublecheck for any overlooked error.For testing the circuit, refer the test-point table and verify the voltages. To test the functionality
of the overall system, proceed as follows: