Академический Документы
Профессиональный Документы
Культура Документы
Contents
1 Preface...................................................................................... 1-1
Before reading the command reference: ........................................................ 1-2
Contents
Setting of daylight saving time................................................................................ 3-8
Display of date and time ........................................................................................3-11
Clearing of daylight saving time.............................................................................3-12
5 Ports.......................................................................................... 5-1
Setting of port blocking/unblocking......................................................................... 5-2
Setting of port speed and MDI/MDI-X..................................................................... 5-3
Setting of GbE port media ...................................................................................... 5-5
Setting of flow control ............................................................................................. 5-6
Setting of port link protection time .......................................................................... 5-7
Setting of SNMP link trap transmission .................................................................. 5-8
Setting of ATM transmission path clock.................................................................. 5-9
Setting of ATM transmission path framing mode...................................................5-10
Display of port setting and status information........................................................5-11
ii
Contents
Display of link trap transmission setting.................................................................5-16
Display of port link protection time.........................................................................5-18
Setting of port cable length....................................................................................5-19
Display of port cable length settings ......................................................................5-21
Setting of TDMP155 port logical interface .............................................................5-23
Display of TDMP155 port logical interface setting .................................................5-25
Setting of impedance.............................................................................................5-26
Display of impedance setting.................................................................................5-27
Display of port (line) alarm status for TDMP155 port.............................................5-28
iii
Contents
Setting of priority discard function in output VLAN units ........................................7-28
Display of maximum band limiting function in output VLAN units ..........................7-32
Clearing of maximum band limiting function in output VLAN units ........................7-35
Setting of priority mapping.....................................................................................7-37
Display of priority mapping ....................................................................................7-38
Creating of priority mapping profile........................................................................7-40
Display of priority mapping profile .........................................................................7-42
Creating of CoS profile ..........................................................................................7-43
Display of CoS profile ............................................................................................7-46
Clearing of CoS profile ..........................................................................................7-48
Setting of input CoS priority mapping ....................................................................7-49
Display of input CoS priority mapping....................................................................7-50
Clearing of CoS priority mapping...........................................................................7-51
Setting of output CoS priority mapping ..................................................................7-52
Display of output CoS priority mapping .................................................................7-53
Clearing of output CoS priority mapping................................................................7-54
Setting of output-side fairness control mode function ............................................7-55
Display of output-side fairness control mode function ...........................................7-56
Setting of priority discard function of output-side fairness control function
of output port .........................................................................................................7-57
Setting of output-side fairness control function rate of output port.........................7-60
Setting of output-side fairness control function weight of output port ....................7-62
Setting of upper threshold of output-side fairness control function of
output port .............................................................................................................7-64
Display of output-side fairness control function of output port ...............................7-66
Clearing of output-side fairness control function of output port..............................7-70
Setting of default priority mapping .........................................................................7-72
Display of default priority mapping ........................................................................7-74
Setting of default burst tolerance...........................................................................7-76
Display of default burst tolerance ..........................................................................7-79
Setting of subtraction cycle....................................................................................7-81
Display of subtraction cycle ...................................................................................7-82
iv
Contents
Display of aging time .............................................................................................. 8-5
Display of MAC learning count in port units............................................................ 8-6
Display of MAC learning count in VLAN units......................................................... 8-8
Display of MAC learning count in device units........................................................ 8-9
Display of MAC learning information .....................................................................8-10
Display of MAC learning information in port units..................................................8-11
Clearing of MAC learning information in port units ................................................8-12
Display of MAC learning information in VLAN units...............................................8-13
Clearing of MAC learning information in VLAN units .............................................8-14
Setting of IFG overrate mode ................................................................................8-15
Display of IFG overrate mode................................................................................8-16
Contents
Display of system priority.......................................................................................9-29
Setting of port priority ............................................................................................9-30
Display of port priority............................................................................................9-31
Setting of link aggregation protection time.............................................................9-32
Display of link aggregation protection time ............................................................9-33
Setting of IGMP Snooping function enable/disable ...............................................9-34
Display of IGMP Snooping function enable/disable information ............................9-35
Display of IGMP Snooping entry for specified MAC ..............................................9-36
Clearing of IGMP Snooping entry for specified group address..............................9-37
Display of IGMP Snooping entry for specified VLAN .............................................9-38
Display of IGMP Snooping entry for specified port number ...................................9-39
Clearing of IGMP Snooping entry for specified VLAN ...........................................9-40
vi
Contents
Clearing of MEG....................................................................................................11-5
Setting of MEP ......................................................................................................11-6
Display of MEP setting information........................................................................11-8
Clearing of MEP ..................................................................................................11-10
Setting of test target MEP....................................................................................11-11
Display of test target MEP setting information.....................................................11-12
Clearing of test target MEP .................................................................................11-13
Setting of associated MEP ID..............................................................................11-14
Clearing of associated MEP ID............................................................................11-15
Setting of MIP......................................................................................................11-16
Display of MIP setting information .......................................................................11-17
Clearing of MIP....................................................................................................11-19
Setting of EtherOAM frame common information ................................................11-20
Display of EtherOAM frame common information ...............................................11-21
Setting of Reply frame returning period ...............................................................11-22
Display of Reply frame returning period ..............................................................11-23
Setting of EtherOAM Continuity Check transmission ..........................................11-24
Setting of RDI operation ......................................................................................11-26
Display of final fault information...........................................................................11-27
Display of CCM error cause ................................................................................11-28
Clearing of CCM error cause...............................................................................11-30
Starting of EtherOAM Loop Back test..................................................................11-31
Starting of EtherOAM Link Trace test ..................................................................11-33
Starting of EtherOAM Frame Delay Measurement test .......................................11-35
Starting of EtherOAM Loss Measurement test ....................................................11-37
Setting of EtherPS enable/disable.......................................................................11-40
Setting of EtherPS control VLAN.........................................................................11-42
Setting of EtherPS lockout...................................................................................11-43
Setting of EtherPS timer ......................................................................................11-44
Changeover of EtherPS state..............................................................................11-45
Resetting of EtherPS state changeover...............................................................11-46
Display of EtherPS configuration information ......................................................11-47
Display of EtherPS status....................................................................................11-49
vii
Contents
Setting of APS lockout...........................................................................................12-4
Setting of APS timer values...................................................................................12-5
Changeover of APS...............................................................................................12-6
Resetting of APS changeover ...............................................................................12-8
Display of APS settings and status........................................................................12-9
viii
Contents
Clearing path setting between ATMs...................................................................13-40
ix
Contents
Setting of TDM group name ..................................................................................17-8
Display of TDM group name setting ....................................................................17-10
Clearing of TDM group name setting...................................................................17-12
Setting of TDM path ............................................................................................17-14
Display of TDM path setting information..............................................................17-16
Clearing of TDM path ..........................................................................................17-18
Contents
Setting of SNMP enable/disable............................................................................20-2
Setting of SNMP manager.....................................................................................20-3
Setting of SNMP trap manager..............................................................................20-4
Clearing of SNMP manager settings .....................................................................20-5
Clearing of SNMP trap manager settings ..............................................................20-6
Setting of SNMP unauthorized access trap transmission ......................................20-7
Display of SNMP setting information .....................................................................20-8
Setting of access list............................................................................................20-10
Display of access list ...........................................................................................20-11
Clearing of access list..........................................................................................20-12
Display of session ...............................................................................................20-13
Clearing of session ..............................................................................................20-14
Setting of remote log enable/disable ...................................................................20-15
Setting of syslog server and message facility......................................................20-16
Display of syslog server configuration information ..............................................20-17
Clearing of syslog server .....................................................................................20-18
Setting of syslog message level remapping ........................................................20-19
Display of syslog message level mapping status ................................................20-20
Clearing of syslog message level remapping ......................................................20-21
Display of local log ..............................................................................................20-22
Clearing of local log .............................................................................................20-24
Setting of NTP access time .................................................................................20-25
Setting of IP address of NTP server ....................................................................20-26
Display of NTP server setting information ...........................................................20-27
Clearing of IP address of NTP server ..................................................................20-28
xi
Contents
Setting of ATM loopback monitoring function ......................................................21-18
Display of ATM loopback monitoring information ................................................21-20
Clearing of ATM loopback monitoring function ....................................................21-22
22 Monitors................................................................................ 22-1
Display of port counter...........................................................................................22-2
Clearing of port counter .........................................................................................22-5
Display of discard counter .....................................................................................22-6
Display of VLAN counter .......................................................................................22-8
Clearing of VLAN counter....................................................................................22-13
Registration of VLAN counter ..............................................................................22-14
Display of VLAN counter registration information ................................................22-16
Clearing of VLAN counter registration .................................................................22-18
Registration of PVC counter ................................................................................22-19
Display of PVC counter registration information ..................................................22-20
Clearing of PVC counter registration ...................................................................22-21
Display of byte/frame counter information in PVC units.......................................22-22
Clearing of byte/frame counter information in PVC units .....................................22-24
Display of cell counter information.......................................................................22-25
Display of cell counter information in F4 units .....................................................22-28
Display of cell counter information in F5 units .....................................................22-31
Display of cell counter information in IMA port units............................................22-34
Clearing of cell counter information .....................................................................22-36
Setting of mirroring start or stop ..........................................................................22-37
Display of mirroring settings ................................................................................22-39
xii
Contents
Downloading of startup configuration from ftp server ..........................................23-14
Display of running configuration ..........................................................................23-15
Display of startup configuration ...........................................................................23-17
Display of configuration difference ......................................................................23-19
Setting of trap transmission selection ..................................................................23-20
Display of trap transmission selection setting status ...........................................23-24
Display of all setting information..........................................................................23-27
Saving of setting information ...............................................................................23-29
Clearing of line module configuration ..................................................................23-30
Clearing of startup configuration..........................................................................23-33
Setting of backup server......................................................................................23-34
Clearing of backup server....................................................................................23-35
Setting of backup schedule .................................................................................23-36
Display of backup information .............................................................................23-37
Display of current fault and alarm information .....................................................23-38
Clearing of WR fault ............................................................................................23-40
Display of past fault information ..........................................................................23-41
Clearing of past fault information.........................................................................23-43
Display of device installation status and other various statuses ..........................23-44
Display of bridge information for device...............................................................23-46
Display of module ID information.........................................................................23-47
Display of various version information .................................................................23-49
Display of device temperature .............................................................................23-51
Setting of autonomous rebooting enable/disable.................................................23-53
Display of autonomous rebooting settings...........................................................23-54
Display of CPU usage .........................................................................................23-55
Display of memory usage ....................................................................................23-57
xiii
Contents
Resetting of entire device ....................................................................................24-13
Resetting of UGSW module ................................................................................24-15
Resetting of line module ......................................................................................24-17
Display of reset factor..........................................................................................24-18
OUS setting of UGSW module ............................................................................24-19
OUS setting of line module..................................................................................24-20
Removing of external memory.............................................................................24-21
Appendix 2
xiv
Preface
1 Preface
1-1
Preface
Before reading the command reference:
This device has three types of modes to use commands.
General mode:
Mode to use terminal local set commands that do not involve display
system and configuration update (default)
Privileged mode:
Maintenance mode:
General
Mode
enable
Privileged
Mode
disable
maintenance
Maintenance
Mode
end
Marks located at the top of descriptions for each command indicate following meanings:
Privilege
General
Maintenance
Save
Synchronize
Indicates that the settings automatically synchronize with the other system
when the device is operated in dual mode.
SBY execution
Indicates that the command can be used by the standby system when the
device is operated in dual mode.
1-2
Preface
Commands described with multiple input formats vary parameters to be specified according
to the settings.
In such a case, the key parameter is indicated as "Px (bold italic)" with an explanation.
Example) P1 (aaa/bbb) P2 P3 : When aaa or bbb is specified by P1, specify P2 and P3.
P1 (ccc) P4 P5
: When ccc is specified by P1, specify P4 and P5.
atm
atm155
atmp
atmp
atmp155
atmp155
fe
gbe
gbe-pv, gbe-pv2
gmx
(gm8-t), (gm8-x)
tdmp
tdmp
tdmp155
tdmp155
1-3
Preface
(Blank page)
1-4
Operation Modes
2 Operation Modes
2-1
Operation Modes
Privilege
General
Save
Synchronize
SBY execution
exit
Logout
This command is used for logout from CLI.
Input format
exit
Parameter
None
Default value
None
Usage condition
None
Note
None
Input example
*Switch@1# exit
Output item
Related
commands
enable
disable
2-2
Operation Modes
Privilege
General
Save
Synchronize
SBY execution
enable
Switch from general mode to privileged mode
Enables you to switch from general mode to privileged mode.
Input format
enable
Parameter
None
Default value
None
Usage condition
Interactively enter your privileged mode password. When not setting this password,
press [Enter].
Note
None
Input example
*Switch@1> enable
Input enable password:
*Switch@1#
Output item
Related
commands
exit
disable
Logout
Switch from privileged mode to general mode
2-3
Operation Modes
Privilege
General
Save
Synchronize
SBY execution
disable
Switch from privileged mode to general mode
Enables you to switch from privileged mode to general mode.
Input format
disable
Parameter
None
Default value
None
Usage condition
None
Note
None
Input example
*Switch@1# disable
*Switch@1>
Output item
Related
commands
exit
enable
Logout
Switch from general mode to privileged mode
2-4
Operation Modes
Privilege
General
Save
Synchronize
SBY execution
maintenance
Switch from privileged mode to maintenance mode
Enables you to switch from privileged mode to maintenance mode.
Input format
maintenance
Parameter
None
Default value
None
Usage condition
If another session is in maintenance mode, you cannot switch from privileged mode to
maintenance mode.
Note
None
Input example
*Switch@1# maintenance
*Switch@1%
Output item
Related
command
end
2-5
Operation Modes
Privilege
General
Save
Synchronize
SBY execution
Parameter
None
Default value
None
Usage condition
Note
Set this password with 4 to 16 ASCII characters other than [space], [!], [?], and [control
character].
Input example
Output item
Related
commands
enable
clear enable password
2-6
Operation Modes
Privilege
General
Save
Synchronize
SBY execution
Parameter
None
Default value
None
Usage condition
Note
Set this password with 4 to 16 ASCII characters other than [space], [!], [?], and [control
character].
Input example
Output item
Related
commands
enable
set enable password
2-7
Operation Modes
Privilege
General
Save
Synchronize
SBY execution
Parameter
None
Default value
None
Usage condition
Note
Set this password with 4 to 16 ASCII characters other than [space], [!], [?], and [control
character].
Input example
Output item
Related
commands
exit
clear login password
Logout
Clearing of login password
2-8
Operation Modes
Privilege
General
Save
Synchronize
SBY execution
Parameter
None
Default value
None
Usage condition
Note
Set this password with 4 to 16 ASCII characters other than [space], [!], [?], and [control
character].
Input example
Output item
Related
commands
exit
set login password
Logout
Setting of login password
2-9
Operation Modes
Privilege
General
Save
Synchronize
SBY execution
Parameter
Default value
P1: Switch
Usage condition
None
Notes
Terminal prompts for other than the set terminal are set at reconnection.
Set this prompt name with ASCII characters other than ["], [?], and [control character].
When using [space], enclose the entire character string in double quotation marks.
Input example
Output item
Related
command
None
2-10
Operation Modes
Privilege
General
Save
Synchronize
SBY execution
Parameters
Default value
P1: on
P2: 22
Usage condition
None
Note
Input example
Output item
Related
command
2-11
Operation Modes
Privilege
General
Save
Synchronize
SBY execution
Parameters
Default value
P1: on
P2: 22
Usage condition
None
Notes
Local terminal scroll control only for the set terminal is set.
A local terminal operates in scroll control default setting at reconnection.
Input example
Output item
Related
command
2-12
Operation Modes
Privilege
General
Save
Synchronize
SBY execution
Parameter
Default values
Usage condition
None
Notes
Input example
Output item
Related
command
2-13
Operation Modes
Privilege
General
Save
Synchronize
SBY execution
Parameter
Default value
P1: 5 minutes
Usage condition
None
Note
Automatic logout time for other than the set terminal is set at reconnection.
Input example
Output item
Related
command
2-14
Operation Modes
Privilege
General
Synchronize
SBY execution
Parameter
None
Default value
None
Usage condition
None
Note
None
Input example
Output items
Related
commands
2-15
Operation Modes
Privilege
General
Save
Synchronize
SBY execution
Parameters
Default value
None
Usage condition
Notes
Set a user account with ASCII characters other than ["], [?], and [control character].
When using [space], enclose the entire character string in double quotation marks.
You can register up to six user accounts except the default user account.
You can change the password of the registered user account by specifying the same
user account name and user privilege as the registered user account and entering the
old password.
Set the password with 4 to 16 ASCII characters other than [space], [!], [?], and [control
character].
Input example
Output item
Related
commands
2-16
Operation Modes
Privilege
General
Synchronize
SBY execution
Parameter
None
Default value
None
Usage condition
None
Note
None
Input example
Output items
Related
commands
2-17
Operation Modes
Privilege
General
Save
Synchronize
SBY execution
Parameter
Default value
None
Usage condition
None
Notes
Input example
Output item
Related
commands
2-18
Operation Modes
Privilege
General
Save
Synchronize
SBY execution
set command-mode
Setting of command mode
Sets command mode.
Input format
set command-mode P1
Parameter
Default value
P1: normal
Usage condition
None
Notes
If command mode is safety mode, the command sequence control function, execution
confirmation function, and overwrite setting suppression function are valid. For the
target commands of each function, refer to "Command Mode Functions" of "Method of
Operating Maintenance and Management Functions" in the "Instruction Manual".
Input example
Output item
Related
command
show command-mode
2-19
Operation Modes
Privilege
General
Synchronize
SBY execution
show command-mode
Display of command mode settings
Shows command mode settings.
Input format
show command-mode
Parameter
None
Default value
None
Usage condition
None
Note
None
Input example
Output item
Related
command
set command-mode
2-20
Global Configuration
3 Global Configuration
3-1
Global Configuration
Privilege
General
Save
Synchronize
SBY execution
Parameter
Default value
None
Usage condition
None
Notes
To return the set administrator contact to the default value, set in P1.
Set an administrator contact with ASCII characters (excluding control characters) like
normal command entry.
Input example
Output item
Related
command
3-2
Global Configuration
Privilege
General
Save
Synchronize
SBY execution
Parameter
Default value
None
Usage condition
None
Notes
To return the set system name to the default value, set in P1.
Set a system name with ASCII characters (excluding control characters) like normal
command entry.
Input example
Output item
Related
command
3-3
Global Configuration
Privilege
General
Save
Synchronize
SBY execution
Parameter
Default value
None
Usage condition
None
Notes
To return the set system location to the default value, set in P1.
Set a system location with ASCII characters (excluding control characters) like normal
command entry.
Input example
Output item
Related
command
3-4
Global Configuration
Privilege
General
Synchronize
SBY execution
Parameter
None
Default value
None
Usage condition
None
Note
None
Input example
Output items
Related
commands
3-5
Global Configuration
Privilege
General
Save
Synchronize
SBY execution
date
Setting of date and time
Sets system date and time.
Input format
date P1 P2
Parameters
Default value
None
Usage condition
None
Note
Input example
Output item
Related
command
3-6
Global Configuration
Privilege
General
Save
Synchronize
SBY execution
Parameter
Default value
P1: +9:00
Usage condition
Note
None
Input example
Output item
Related
commands
date
show system date
3-7
Global Configuration
Privilege
General
Save
Synchronize
SBY execution
Parameters
P1: Start date (daylight saving time specification by date) specification or daylight saving
time specification by week {first | second | third | fourth | last}
- Start date (daylight saving time specification by date) (mm/dd)
mm: Month (01-12)
dd: Date (01-31)
- Daylight saving time specification by week
first: The first week
second: The second week
third: The third week
fourth: The fourth week
last: The last week
When start date (daylight saving time specification by date) is specified in P1.
P2: Start time (hh/mm)
hh: Hour (00-23)
mm: Minute (00-59)
P3: End date (mm/dd)
mm: Month (01-12)
dd: Date (01-31)
P4: End time (hh/mm)
hh: Hour (00-23)
mm: Minute (00-59)
3-8
Global Configuration
When daylight saving time specification by week is specified in P1.
P5: a start day of the week {sunday | monday | tuesday | wednesday | thursday |
friday | saturday}
sunday: Sunday
monday: Monday
tuesday: Tuesday
wednesday: Wednesday
thursday: Thursday
friday: Friday
saturday: Saturday
P6: Start month (1-12)
P7: Start time (hh:mm)
hh: Hour (00-23)
mm: Minute (00-59)
P8: End week {first | second | third | fourth | last}
first: The first week
second: The second week
third: The third week
fourth: The fourth week
last: The last week
P9: an end day of the week {sunday | monday | tuesday | wednesday | thursday
| friday | saturday}
sunday: Sunday
monday: Monday
tuesday: Tuesday
wednesday: Wednesday
thursday: Thursday
friday: Friday
saturday: Saturday
P10: End month (1-12)
P11: End time (hh:mm)
hh: Hour (00-23)
mm: Minute (00-59)
P12: Time difference by daylight saving time (hh:mm)
hh: Hour (00-23)
mm: Minute (00 to 59)
* If P12 is omitted, 01:00 is assumed.
Default value
None
Usage condition
In date specification, you cannot specify the same date for start/end date of daylight
saving time. Also, in specification of a day of week, you cannot specify the same
month/date/day of week for start/end date of daylight saving time.
3-9
Global Configuration
Notes
When daylight saving time starts, the clock is not set to the set start time, moving
forward corresponding to the time difference by daylight saving time.
Example) When the start time is 1:00 and time difference by daylight saving time is 0:30
0:58 -> 0:59 -> 1:30
When daylight saving time ends, the clock is not set to the set end time, moving
backward corresponding to the time difference by daylight saving time.
Example) When the end time is 2:00 and time difference by daylight saving time is 0:30
1:58 -> 1:59 -> 1:30
If daylight saving time is shorter than time difference by daylight saving time, the
specified end date is changed to that of the next year.
If the start date or the end date is Feb. 29, daylight saving time is applied only to leap
years. If Feb. 29 is set as the start date and the daylight saving time is shorter than
time difference by daylight saving time, the end date is changed to that of the next year
of the leap year. If Feb. 29 is set as the end date and the daylight saving time is shorter
than time difference by daylight saving time, the start date is changed to that of the
previous year of a leap year.
During daylight saving time, (DST) is shown in the current time.
Input example
Output item
Related
commands
date
show system date
clear system daylight-time
3-10
Global Configuration
Privilege
General
Synchronize
SBY execution
Parameter
Default value
None
Usage condition
None
Note
None
Input example
Output items
Date: Date
Time: Time
Time Zone: Time difference from Greenwich mean time
Daylight Time Start : Start date and time of daylight saving time
Daylight Time End : End date and time of daylight saving time
Daylight Time Offset : Time difference by daylight saving time
Related
commands
date
set system timezone
set system daylight-time
3-11
Global Configuration
Privilege
General
Save
Synchronize
SBY execution
Parameter
None
Default value
None
Usage condition
None
Note
None
Input example
Output item
Related
commands
date
show system date
set system daylight-time
3-12
Administration Ports
4 Administration Ports
4-1
Administration Ports
Privilege
General
Save
Synchronize
SBY execution
Parameters
Default value
None
Usage conditions
You cannot use the network addresses set in the set ip address in-band command
(Setting of in-band IP address) and set ip route command (Setting of static route).
You cannot set 0.xxx.xxx.xxx/127.xxx.xxx.xxx and 224.xxx.xxx.xxx to 255.xxx.xxx.xxx
as the IP address. (xxx is any numeric character.)
You cannot set 192.168.128.0/24 and 192.168.129.0/24 as the network address.
You cannot set 0 or 1 to all bits of the host part as the IP address.
Note
If you log in via telnet communication, the login session close confirmation message is
output.
Input examples
Output item
Related
commands
4-2
Administration Ports
Privilege
General
Save
Synchronize
SBY execution
Parameter
Default value
None
Usage condition
None
Note
If you log in via telnet communication, the login session close confirmation message is
output.
Input examples
Output item
Related
commands
4-3
Administration Ports
Privilege
General
Save
Synchronize
SBY execution
Parameters
Default value
None
Usage conditions
You cannot use the network addresses set in the set ip address out-band command
(Setting of out-band IP address) and set ip route command (Setting of static route).
You cannot set 0.xxx.xxx.xxx/127.xxx.xxx.xxx and 224.xxx.xxx.xxx to 255.xxx.xxx.xxx
as the IP address. (xxx is any numeric character.)
You cannot set 192.168.128.0/24 and 192.168.129.0/24 as the network address.
You cannot set 0 or 1 to all bits of the host part as the IP address.
Note
If you log in via telnet communication, the login session disconnection confirmation
message is output.
Input examples
Output item
Related
commands
4-4
Administration Ports
Privilege
General
Synchronize
SBY execution
Parameter
None
Default value
None
Usage condition
None
Note
None
Input example
Output items
Module: Module
Admin: Port block/unblock setting
enabled: Port unblocked
disabled: Port blocked
Related
commands
4-5
Administration Ports
Privilege
General
Save
Synchronize
SBY execution
Parameter
Default value
None
Usage condition
None
Note
If you log in via telnet communication, the login session close confirmation message is
output.
Input example
Output item
Related
commands
4-6
Administration Ports
Privilege
General
Save
Synchronize
SBY execution
Parameter
P1: IP address
Default value
None
Usage conditions
Note
If you log in via telnet communication, the login session close confirmation message is
output.
Input example
Output item
Related
commands
4-7
Administration Ports
Privilege
General
Save
Synchronize
SBY execution
Parameter
None
Default value
None
Usage condition
None
Note
If you log in via telnet communication, the login session close confirmation message is
output.
Input example
Output item
Related
commands
4-8
Administration Ports
Privilege
General
Save
Synchronize
SBY execution
set ip route
Setting of static route
Sets a static route.
Input format
set ip route P1 P2 P3 P4
Parameters
Default value
None
Usage conditions
You cannot use the network addresses set in the set ip address in-band command
(Setting of in-band IP address) and set ip address out-band command (Setting of
out-band IP address).
You cannot set 0.xxx.xxx.xxx/127.xxx.xxx.xxx and 224.xxx.xxx.xxx to 255.xxx.xxx.xxx
as the IP address. (xxx is any numeric character.)
If you set 0 or 1 to all bits of the host part as the gateway address or set 1 to all bits as
the destination address, this setting may not provide correct communication.
You cannot set the network addresses 192.168.128.0/24 and 192.168.129.0/24 as the
destination address. Also, you can set the gateway address for the network address
192.168.128.0/24 or 192.168.129.0/24 but this setting does not provide correct
communication.
Note
If you log in via telnet communication, the login session close confirmation message is
output.
Input example
Output item
Related
commands
4-9
Administration Ports
Privilege
General
Synchronize
SBY execution
show ip config
Display of network information
Shows network information for out-band/in-band.
Input format
show ip config
Parameter
None
Default value
None
Usage conditions
Note
None
Input example
4-10
Administration Ports
*Switch@1#
Output items
Module: Module
MAC Address: MAC address
IP Address: IP address
Netmask: Subnet mask
Index: Routing domain
Destination Address: Destination address
Gateway Address: Gateway address
Port: Band
out-band: Out-band communication
in-band : In-band communication
- : No band
Mode: In-band mode
Virtual: User connection test function enabled
Real: Administration port control function enabled
VID: VLAN ID
Name: VLAN name (32 characters)
Address: Virtual IP address
Related
commands
4-11
Administration Ports
Privilege
General
Save
Synchronize
SBY execution
clear ip route
Clearing of static route
Clears a static route.
Input format
clear ip route P1
Parameter
Default value
None
Usage condition
None
Note
Input example
Output item
Related
commands
set ip route
show ip config
4-12
Administration Ports
Privilege
General
Save
Synchronize
SBY execution
Parameters
Default value
P2: enable
Usage condition
None
Note
If you log in via telnet communication, the login session close confirmation message is
output.
Input example
Output item
Related
commands
4-13
Administration Ports
Privilege
General
Save
Synchronize
SBY execution
Parameter
Default values
VLAN-ID: 1
Usage conditions
The VLAN to which the CPU port belongs is set in the set the in-band vid command.
This VLAN transfers all broadcast, multicast, and unknown unicast frames to the CPU
port. To reduce CPU load, use this VLAN separately from user lines.
Note
None
Input example
Output item
Related
commands
4-14
Administration Ports
Privilege
General
Save
Synchronize
SBY execution
Parameters
Default value
None
Usage condition
None
Note
If you log in via telnet communication, the login session close confirmation message is
output.
Input example
Output item
Related
command
4-15
Administration Ports
Privilege
General
Save
Synchronize
SBY execution
Parameter
Default value
P1: disable
Usage condition
None
Note
None
Input example
Output item
Related
command
4-16
Administration Ports
Privilege
General
Synchronize
SBY execution
Parameter
None
Default value
None
Usage condition
None
Note
None
Input example
Output items
Module: Module
Port Speed: Port speed setting
10m-half: 10Mbps Half Duplex
10m-full: 10Mbps Full Duplex
100m-half: 100Mbps Half Duplex
100m-full: 100Mbps Full Duplex
auto: Auto-negotiation
Link Status: Port physical link status
10m-half: 10Mbps Half Duplex
10m-full: 10Mbps Full Duplex
100m-half: 100Mbps Half Duplex
100m-full: 100Mbps Full Duplex
link-down: Link down
--- : Uninstalled
Related
commands
4-17
Administration Ports
Privilege
General
Save
Synchronize
SBY execution
ping
Checking of connection
Checks if connection with the host is correct. To cancel the connection test halfway, press Ctrl + c
combination.
key
Input format
ping P1 [P2]
Parameters
P1: IP address
P2: Execution count (1 to 2147483647)
* If P2 is omitted, 4 times are assumed.
Default value
None
Usage conditions
Note
None
Input example
ttl=255
ttl=255
ttl=255
ttl=255
time<5
time<5
time<5
time<5
ms
ms
ms
ms
--- 192.168.1.212 ping statistics --4 packets transmitted, 4 packets received, 0% packet loss
round-trip min/avg/max/stddev = 0.000/0.000/0.000/0.000 ms
*Switch@1#
Output item
Related
commands
4-18
Administration Ports
Privilege
General
Save
Synchronize
SBY execution
set ip virtual-address
Setting of virtual IP address
Sets a VLAN ID and virtual IP address in the specified index.
Input format
set ip virtual-address P1 P2 P3
Parameters
Default value
None
Usage condition
Notes
Input example
Output item
Related
commands
show ip config
set ip in-band mode
virtual-ping
clear ip virtual-address
4-19
Administration Ports
Privilege
General
Save
Synchronize
SBY execution
virtual-ping
Confirmation of connection with host
Performs the user connection test on the CX2600 side to confirm the connection with the host.
To cancel the user connection test halfway, press [Ctrl]+[c].
Input format
Parameters
Default value
None
Usage conditions
You can enter this command when the in-band user connection test function is
enabled (when virtual is effective).
This virtual-ping cannot be transferred beyond a gateway.
You cannot set 0.xxx.xxx.xxx/127.xxx.xxx.xxx and 224.xxx.xxx.xxx to 255.xxx.xxx.xxx
as the IP address. (xxx is any numeric character.)
Note
Input example
*Switch@1#
Output item
Related
commands
4-20
Administration Ports
Privilege
General
Save
Synchronize
SBY execution
clear ip virtual-address
Clearing of virtual IP address
Clears the virtual IP address of the specified index.
Input format
clear ip virtual-address P1
Parameter
Default value
None
Usage condition
None
Note
None
Input example
Output item
Related
commands
show ip config
set ip in-band mode
set ip virtual-address
virtual-ping
4-21
Administration Ports
Privilege
General
Save
Synchronize
SBY execution
Parameter
Default value
None
Usage condition
None
Notes
If the set in-band mode command enables the in-band user connection test function,
various in-band telnet/SNMP/NTP/syslog/ftp functions are disabled and the connected
in-band telnet session is disconnected. When the telnet session is disconnected,
interactive confirmation is performed.
An attempt to download running-config including this command in in-band mode will fail
because the connected ftp session is also suspended.
Input example
Output item
Related
commands
show ip config
set ip virtual-address
virtual-ping
clear ip virtual-address
4-22
Ports
5 Ports
5-1
Ports
Privilege
General
Save
Synchronize
SBY execution
Parameters
P1: Port (line) type {fe | gbe | gmx | atm | atmp | tdmp | atmp155 | tdmp155}
fe: FE port
gbe: GbE port
gmx: GbE-MUX port
atm: ATM155 port
atmp: ATMP port
tdmp: TDMP port
atmp155: ATMP155 port
tdmp155: TDMP155 port
P2: Port (line) number (Multiple values can be specified.)
P3: Port blocking/unblocking setting {enable | disable}
enable: Port unblocking
disable: Port blocking
Default value
P3: enable
Usage condition
When port blocking is set, the LINK DOWN message may be displayed. When port
unblocking is set, the LINK UP message may be displayed. Whether LINK DOWN
or LINK UP is displayed depends on the physical connection status of the set port.
Note
None
Input example
Output item
Related
command
5-2
Ports
Privilege
General
Save
Synchronize
SBY execution
Input format
- Setting auto
set port speed P1 P2 P3(auto)
- Setting mdi/mdi-x
set port speed P1 P2 P3(10m-full | 100m-full | 1000m-full) [P4]
Parameters
Default values
Usage conditions
Notes
Input example
5-3
Ports
Output item
Related command
5-4
Ports
Privilege
General
Save
Synchronize
SBY execution
If auto-negotiation is specified,
Input format
Parameters
Default value
P3: auto
Usage condition
Note
None
Input example
Output item
Related
command
5-5
Ports
Privilege
General
Save
Synchronize
SBY execution
Parameters
Default value
P3: disable
Usage conditions
Note
You cannot enter this command to the GbE-MUX port because this port does not
support the flow control function.
Input example
Output item
Related
commands
5-6
Ports
Privilege
General
Save
Synchronize
SBY execution
Parameters
Default value
Usage condition
You can set this protection time (0 to 7000 msec) in units of 500 msec.
Note
None
Input example
Output item
Related
command
5-7
Ports
Privilege
General
Save
Synchronize
SBY execution
Parameters
P1: Port (line) type {fe | gbe | gmx | atm | atmp | tdmp | tdmp155 | atmp155}
fe: FE port
gbe: GbE port
gmx: GbE-MUX port
atm: ATM155 port
atmp: ATMP port
tdmp: TDMP port
tdmp155: TDMP155 port
atmp155: ATMP155 port
P2: Port (line) number (Multiple values can be specified.)
P3: SNMP link trap transmission setting {enable | disable}
enable: Enables SNMP link trap transmission
disable: Disables SNMP link trap transmission
Default value
P3: enable
Usage condition
None
Note
None
Input example
Output item
Related
command
5-8
Ports
Privilege
General
Save
Synchronize
SBY execution
Parameters
Default values
ATM155 port
P3: slave
ATMP155 port
P3: master
Usage condition
You can set clock supply mode only for the ATM155/ATMP155 port.
Note
None
Input example
Output item
Related
commands
5-9
Ports
Privilege
General
Save
Synchronize
SBY execution
Input formats
Parameters
Default value
P3: idle
Usage condition
You can set framing mode only for the ATM155/ATMP155 port.
Note
None
Input example
Output item
Related
commands
5-10
Ports
Privilege
General
Synchronize
SBY execution
Parameter
P1: Line module number (single specification) or port (line) number (Multiple values can
be specified.)
Line module number (single specification): 1 to 12
Port (line) number (Multiple values can be specified.)
* If P1 is omitted, all line module numbers are assumed.
Default value
None
Usage condition
None
Note
None
Input example
5-11
Ports
Output items
5-12
Ports
(The following SFP type, Tx Error, and Rx Error are shown only in the
GbE/ATMP155/TDMP155 module.)
SFP type: Type of optical module currently being used
1000BASE-SX: 1000BASE-SX module
1000BASE-LX: 1000BASE-LX module
1000BASE-ZX: 1000BASE-ZX module
1000BASE-BX10-D : 1000BASE-BX10-D module
1000BASE-BX10-U : 1000BASE-BX10-U module
OS3-MS2 : OC3 Multimode Shortreach 2Km
OS3-SI15 : OC3 Singlemode Interreach 15Km
OS3-SL40 : OC3 Singlemode Longreach 40Km
OS3-SL80 : OC3 Singlemode Longreach 80Km
Other: Unsupported optical module
Tx Error: Optical module output error detection status
normal: No output error occurred
fail: An output error occurred
Rx Error: Optical module input error detection status
normal: No input error occurred
fail: An input error occurred
SFP Vendor Information: Optical module vendor information
Vendor Name: Manufacturer name
Vendor OUI: OUI
Vendor Part Number: Manufacturing number
Vendor Revision: Version
Vendor Serial Number: Serial number
(The following Clock, Framing, and Cell Padding are shown only in the
ATM155/ATMP155 line module.)
Clock: Clock control
master: Independent mode setting
slave: External supply mode setting
Framing: Physical layer frame method
sdh: SDH method
sonet: SONET method
Cell Padding: Cell method
idle: Idle cell method
unassigned: Unassigned idle cell method
(The following F1-F3 Status Tables are shown only in the ATM155/ATMP155 line
module.)
F1 Status Table: F1 alarm status
LOS: Loss of signal
LOF: Loss of frame alignment
F2 Status Table : F2 alarm status
MS-AIS: Receiving multiplex section failure
MS-SD: Multiplex section error rate degradation
MS-RDI: Sending multiplex section failure
MS-ERR: Receiving multiplex section error
MS-REI: Sending multiplex section error
5-13
Ports
F3 Status Table: F3 alarm status
LOP: AU pointer error
P-AIS: Receiving transmission path error
LCD: Out-of-cell delineation
detect: Alarm detected
---: Alarm not detected
(The following Framing, Frame Type, and Code/Alarm Status are shown only in the
ATMP/TDMP line module.)
Framing: Frame format setting
crc4: CRC4 multiframe
crc4-no-cas: CRC4 multiframe-without-CAS
non-crc4: G.704
unstructured: unstructured
esf: extended superframe
sf: superframe
Frame Type: Frame type setting
t1: T1 mode
e1: E1 mode
Code: LineCode setting
hdb3: HDB3
ami: AMI
b8zs: B8ZS
Alarm Status: Alarm status
normal: No alarm
los: LOS detection
ais: AIS detection
lof: LOF detection
rai: RAI detection
(The following Framing, SECTION(RS) Status Table, and LINE(MS) Status Table are
only shown in the TDMP155 line module.)
Framing: Frame format
sdh: SDH method
sonet: SONET method
SECTION(RS) Status Table: RS alarm status
LOS: Foss of frame detection
LOF: Loss of frame alignment continuous detection
OOF: Loss of frame alignment detection
RS-TIM: Detection of mismatch in path trace character string
RS-BIP: BIP error (B1) detected
LINE(MS) Status Table: MS alarm status
MS-AIS: Receiving multiplex section failure detected
MS-DEG: B2 error rate 10-6 or higher detection
MS-EXC: B2 error rate 10-3 or higher detection
MS-RDI: Sending multiplex section failure detection
MS-REI: Sending multiplex section error detection
MS-BIP: BIP error (B2) detection
5-14
Ports
Related
commands
5-15
Ports
Privilege
General
Synchronize
SBY execution
Parameter
Default value
None
Usage condition
None
Note
None
Input examples
5-16
Ports
Output items
Related
command
5-17
Ports
Privilege
General
Synchronize
SBY execution
Parameter
Default value
None
Usage condition
None
Note
None
Input example
Output items
Related
command
5-18
Ports
Privilege
General
Save
Synchronize
SBY execution
Parameters
Default value
Usage condition
Note
None
5-19
Ports
Input example
set
set
set
set
set
set
port
port
port
port
port
port
cable-length
cable-length
cable-length
cable-length
cable-length
cable-length
1/3 short
1/1-2,1/4-8 short 399ft
3/1 long 7.5db
3/2 long gain21db
3/2-4,3/5-8 long 7.5db gain31db
12/1 initial
Output item
Related
commands
5-20
Ports
Privilege
General
Synchronize
SBY execution
Parameter
Default value
None
Usage condition
None
Note
None
Input example
Output items
5-21
Ports
Related
commands
5-22
Ports
Privilege
General
Save
Synchronize
SBY execution
Parameters
Default values
Usage
conditions
5-23
Ports
Note
None
Input examples
*Switch@1#
*Switch@1#
*Switch@1#
*Switch@1#
set
set
set
set
port
port
port
port
logical-interface
logical-interface
logical-interface
logical-interface
1/1
1/1
2/1
2/1
Output item
Related
commands
5-24
Ports
Privilege
General
Save
Synchronize
SBY execution
Parameters
Default value
None
Usage condition
None
Note
None
Input example
Output items
Related
commands
5-25
Ports
Privilege
General
Save
Synchronize
SBY execution
Parameters
Default value
P2: e1-120
Usage condition
The frame type of the specified port (line) must be set to the E1 mode.
Note
None
Input examples
*Switch@1#
*Switch@1#
*Switch@1#
*Switch@1#
set
set
set
set
port
port
port
port
impedance
impedance
impedance
impedance
1/1 e1-75
12/2-5 e1-75
5/1-8 e1-120
6/1-5,7,8 e1-120
Output item
Related
commands
5-26
Ports
Privilege
General
Save
Synchronize
SBY execution
Parameter
Default value
None
Usage condition
None
Note
None
Input example
Output items
Related
commands
5-27
Ports
Privilege
General
Synchronize
SBY execution
Parameters
Default value
None
Usage condition
Note
None
5-28
Ports
Input example
Output items
5-29
Ports
HO-PATH Status: Detailed display of higher path alarms
Port: Port number (1/1-12/1)
TUG-3/STS-1: TUG-3/STS-1 number
AU-AIS : AU-AIS alarm detection status
AU-LOP: AU-LOP alarm detection status
HP-TIM: HP-TIM alarm detection status
HP-UNEQ: HP-UNEQ alarm detection status
HP-PLM: HP-PLM alarm detection status
HP-EXC: HP-EXC alarm detection status
HP-DEG: HP-DEG alarm detection status
HP-REI: HP-REI alarm detection status
HP-RDI: HP-RDI alarm detection status
HP-BIP: HP-BIP alarm detection status
detect: Detection status
---: No detection status
LO-PATH Status: Detailed display of lower path alarms
Port: Port number (1/1-12/1)
Logical Port: Logical port number
SDH: 1-3 / 1-7 / 1-3
SONET: 1-3 / 1-7 / 1-4
TU-AIS: TU-AIS alarm detection status
TU-LOP: TU-LOP alarm detection status
TU-LOM: TU-LOM alarm detection status
LP-TIM: LP-TIM alarm detection status
LP-UNEQ: LP-UNEQ alarm detection status
LP-PLM: LP-PLM alarm detection status
LP-EXC: LP-EXC alarm detection status
LP-DEG: LP-DEG alarm detection status
LP-REI: LP-REI alarm detection status
LP-RD : LP-RDI alarm detection status
LP-BIP: LP-BIP alarm detection status
detect: Detection status
---: No detection status
PDH Status : Detailed display of PDH alarms
Port: Port number
Logical Port: Logical port number
SDH: 1-3 / 1-7 / 1-3
SONET: 1-3 / 1-7 / 1-4
AIS: AIS alarm detection status
OOF: OOF alarm detection status
RAI: RAI alarm detection status
SEF: SEF alarm detection status
FAS: FAS alarm detection status
CRC: CRC alarm detection status
5-30
Ports
detect: Detection status
---: No detection status
Related
command
5-31
Ports
(Blank page)
5-32
VLAN
6 VLAN
6-1
VLAN
Privilege
General
Save
Synchronize
SBY execution
Parameters
Default value
None
Usage conditions
If VLAN tag swapping is set in a port, you cannot set a VLAN ID that is already being
used as the swapping destination VLAN ID.
If command mode is safety mode, the following conditions are applied:
1) When setting a tagbase VLAN in a line where a portbase VLAN is set, you cannot
set a VLAN ID. You can set a VLAN ID only when no VLAN exists.
2) When setting a tagbase VLAN in the VLAN tag swapping setting line, you cannot
set a VLAN ID that is duplicated with the swapping source VLAN ID.
The following conditions are applied when a tagbase VLAN is set in the GbE-MUX line
module.
1) You can register up to 32 VLANs per port (line).
2) In the same line module, you cannot set a VLAN ID that is duplicated with any of
the following VLAN IDs in several lines:
- VLAN ID for which a tagbase VLAN is set
- Swapping source VLAN ID for which VLAN tag swapping is set
Note
If a set vlan tagbase command without a VLAN ID is entered to the portbase VLAN
setting line when command mode is safety mode, execution is confirmed.
Input example
Output item
Related
commands
6-2
VLAN
Privilege
General
Save
Synchronize
SBY execution
Parameters
Default value
None
Usage condition
None
Note
Input example
Output item
Related
commands
6-3
VLAN
Privilege
General
Save
Synchronize
SBY execution
Parameters
Default value
P3: admit-all
Usage conditions
You cannot set untag as the frame type for the lines where an Ethernet type other than
0x8100 is set.
If command mode is safety mode, you can set a portbase VLAN only in lines where
tagbase VLAN without VLAN ID is set.
Note
None
Input example
Output item
Related
commands
6-4
VLAN
Privilege
General
Synchronize
SBY execution
Parameter
Default value
None
Usage condition
None
Note
None
Input example
Output items
6-5
VLAN
Related
commands
6-6
VLAN
Privilege
General
Synchronize
SBY execution
Parameter
Default value
None
Usage condition
None
Note
None
Input example
Output items
VID: VLAN ID
Name: VLAN name
Portbase Ports: Portbase VLAN ports (lines)
Tagbase Ports: Tagbase VLAN ports (lines)
Related
commands
6-7
VLAN
Privilege
General
Save
Synchronize
SBY execution
Parameters
Default value
None
Usage conditions
You cannot set the same port (line) number in the portbase VLAN (port) number and
tagbase VLAN port (line) number.
You cannot set a line where the total number of tagbase VLANs and VLAN tag
swapping settings exceeds 100 as a portbase VLAN port (line).
The usage conditions of the set portbase VLAN command are applied to the portbase
VLAN in this command. The usage conditions of the set tagbase VLAN command
are applied to the tagbase VLAN in this command.
If the portbase VLAN is set, admit-all (default value) is set as the frame type.
Note
None
Input example
Output item
Related
commands
6-8
VLAN
Privilege
General
Save
Synchronize
SBY execution
Parameters
Default value
None
Usage conditions
You cannot reassign the VLAN ID that is already being used as the swapping
destination VLAN ID in the port to another VLAN as the swapping destination VLAN ID.
If command mode is safety mode, the following conditions are applied:
1) You cannot set VLAN tag swapping for the portbase VLAN setting line.
2) When setting VLAN tag swapping in the tagbase VLAN setting line, you cannot set a
swapping source VLAN ID that is duplicated with the VLAN ID.
3) When setting VLAN tag swapping in the VLAN tag swapping setting line, you cannot
overwrite the VLAN ID that is already being used as the swapping source VLAN ID.
The following conditions are applied when VLAN tag swapping is set in the GbE-MUX
line module.
1) You can register up to 32 VLANs per port (line).
2) In the same line module, you cannot set a VLAN ID that is duplicated with any of the
following VLAN IDs in several lines:
- VLAN ID for which a tagbase VLAN is set
- Swapping source VLAN ID for which VLAN tag swapping is set
3) In the same port (line), you cannot set the swapping destination VLAN ID that is the
same as the swapping destination VLAN ID for which VLAN tag swapping.
Note
None
Input example
Output item
Related
commands
6-9
VLAN
Privilege
General
Synchronize
SBY execution
Parameters
Default value
None
Usage condition
None
Note
None
Input example
Output items
Related
commands
6-10
VLAN
Privilege
General
Save
Synchronize
SBY execution
Parameters
Default value
None
Usage condition
None
Note
Input example
Output item
Related
commands
6-11
VLAN
Privilege
General
Synchronize
SBY execution
Parameter
None
Default value
None
Usage condition
None
Note
None
Input example
Output item
Related
commands
6-12
VLAN
Privilege
General
Save
Synchronize
SBY execution
Parameters
Default value
P2: 0x8100
Usage conditions
If untag is specified as the frame type in the port (line) where a portbase is set, you
cannot set an Ethernet type value other than 0x8100 in the port (line).
If a portbase is specified in the set PVC-VLAN mode command when the ATM line
module is set, you cannot set an Ethernet type value other than 0x8100.
For GbE-MUX, you can specify only a line module number.
For other line module types, you can specify only a port (line) number.
Note
If the Ethernet type for VLAN tag recognition is set in GbE-MUX with line module
number specification, the Ethernet type values of all ports (lines) belonging to the line
module are set to the same value.
Input example
Output item
Related
commands
6-13
VLAN
Privilege
General
Synchronize
SBY execution
Parameter
Default value
None
Usage condition
None
Note
None
Input example
Output items
Related
command
6-14
VLAN
Privilege
General
Save
Synchronize
SBY execution
Parameters
Default value
None
Usage condition
None
Note
None
Input example
Output item
Related
commands
6-15
VLAN
Privilege
General
Save
Synchronize
SBY execution
Parameter
Default value
None
Usage condition
None
Note
None
Input example
Output item
Related
commands
6-16
QoS
7 QoS
7-1
QoS
Privilege
General
Save
Synchronize
SBY execution
Parameters
Default value
P2: both
Usage conditions
If the maximum band limiting function is set, you cannot change maximum band limiting
operation mode.
If the port type is FE, ATM155, ATMP, TDMP, ATMP155, or TDMP155, an error occurs
when this command is entered.
Note
None
Input examples
Output item
7-2
QoS
Related
commands
7-3
QoS
Privilege
General
Synchronize
SBY execution
Parameter
None
Default value
None
Usage condition
None
Note
None
Input example
Output items
7-4
QoS
Related
commands
7-5
QoS
Privilege
General
Save
Synchronize
SBY execution
- Specifying VLAN
set qos in-rate maximum P1 P2 P3(vid) P4 P5(maximum band limiting value)
- Specifying Remaining-VLAN
set qos in-rate maximum P1 P2 P3(remain) P5(maximum band limiting value)
- Specifying separate mode (specifying VLAN)
set qos in-rate maximum P1 P2 P3(vid) P4 P5(separate mode)
[P6] [P7] [P8] [P9]
- Specifying separate mode (specifying Remaining-VLAN)
set qos in-rate maximum P1 P2 P3(remain) P5(separate mode)
[P6] [P7] [P8] [P9]
Parameters
7-6
QoS
P5: Maximum band limiting value or separate mode {separate | separate-red}
Maximum band limiting value(Kbps)
FE port: 0 to 100000(Kbps)
GbE port: 0 to 1000000(Kbps)
* The setting granularity is 25(Kbps).
Separate mode
separate: Separate mode
separate-red: Separate mode (RED use)
When separate mode {separate | separate-red} is specified in P5.
P6: Maximum band limiting value of class A
FE port: class a 0 to 100000(Kbps)
GbE port: class a 0 to 1000000(Kbps)
P7: Maximum band limiting value of class B
FE port: class-b 0 to 100000(Kbps)
GbE port: class-b 0 to 1000000(Kbps)
P8: Maximum band limiting value of class C
FE port: class-c 0 to 100000(Kbps)
GbE port: class-c 0 to 1000000(Kbps)
P9: Maximum band limiting value of class D
FE port: class-d 0 to 100000(Kbps)
GbE port: class-d 0 to 1000000(Kbps)
* The setting granularity in P6 to P9 is 25(Kbps).
Default values
Usage conditions
The number of VLANs that can be registered on a corresponding port depends on the
maximum band limiting operation mode to be set. The following table shows the
number of VLANs that can be set for one port according to a specified maximum band
limiting operation mode.
Maximum band limiting
operation mode
FE port
GbE port
64
1024
128
2048
In input mode (in) and input/output mode (both), one place is used for Remaining-VLAN
among the number of settable VLANs.
Notes
If P6 to P9 are omitted, the values that are already set are pre-retained.
If P6 to P9 are omitted when maximum band limiting operation mode is switched, the
default values are set.
Input examples
*Switch@1# set qos in-rate maximum fe 3/7 vid 100 separate-red class-a 1000
class-b 2000
*Switch@1# set qos in-rate maximum gbe 5/1 vid VLAN200 separate class-c 3000
class-d 4000
*Switch@1# set qos in-rate maximum fe 1/7 vid 50 10000
*Switch@1#
7-7
QoS
Output item
Related
commands
7-8
QoS
Privilege
General
Save
Synchronize
SBY execution
- Specifying VLAN
set qos in-class-map maximum P1 P2 P3 (vid) P4 P6 (class-a) P7 P8 P9 P10 P11 P12
P13
- Specifying Remaining-VLAN
set qos in-class-map maximum P1 P2 P3 (remain) P6 (class-a) P7 P8 P9 P10 P11
P12 P13
- Specifying separate mode (specifying VLAN)
set qos in-class-map maximum P1 P2 P3 (vid) P4 P5 (separate mode) P6 (class-a)
P7 P8 P9 P10 P11 P12 P13
- Specifying separate mode (specifying Remaining-VLAN)
set qos in-class-map maximum P1 P2 P3 (remain) P5 (separate mode) P6 (class-a)
P7 P8 P9 P10 P11 P12 P13
- Specifying default (specifying VLAN)
set qos in-class-map maximum P1 P2 P3 (vid) P4 [P5 (separate)] P6 (initial)
- Specifying default (specifying Remaining-VLAN)
set qos in-class-map maximum P1 P2 P3 (remain) [P5 (separate)] P6 (initial)
- Specifying default (RED use) (specifying VLAN)
set qos in-class-map maximum P1 P2 P3 (vid) P4 P5 (separate-red) P6 (initial)
- Specifying default (RED use) (specifying Remaining-VLAN)
set qos in-class-map maximum P1 P2 P3 (remain) P5 (separate-red) P6 (initial)
Parameters
7-9
QoS
When P5 is omitted.
P6: Class A priority {class-a} or default setting {initial}
class-a: Class A priority specification
initial: Default specification
When class-a is specified in P6.
P7: Priority specification {priority | unset}
priority: 0 to 7 (Multiple values can be specified.)
unset: none
P8: Class B priority {class-b}
P9: Priority specification {priority | unset}
priority: 0 to 7 (Multiple values can be specified.)
unset: none
P10: Class C priority {class-c}
P11: Priority specification {priority | unset}
priority: 0 to 7 (Multiple values can be specified.)
unset: none
P12: Class D priority {class-d}
P13: Priority specification {priority | unset}
priority: 0 to 7 (Multiple values can be specified.)
unset: none
When P5 is specified.
P6: Class A priority {class-a} or default setting {initial}
class-a: Class A priority specification
initial: Default specification
When class-a is specified in P6.
P7: Priority specification {priority | broadcast | multicast |
broadcast&multicast | unset}
priority: 0 to 7 (Multiple values can be specified.)
broadcast: broadcast
multicast: multicast
broadcast&multicast: bc+mc
unset: none
P8: Class B priority {class-b}
P9: Priority specification {priority | broadcast | multicast |
broadcast&multicast | unset}
priority: 0 to 7 (Multiple values can be specified.)
broadcast: broadcast
multicast: multicast
broadcast&multicast: bc+mc
unset: none
P10: Class C priority {class-c}
P11: Priority specification {priority | broadcast | multicast |
broadcast&multicast | unset}
priority: 0 to 7 (Multiple values can be specified.)
broadcast: broadcast
multicast: multicast
broadcast&multicast: bc+mc
unset: none
P12: Class D priority {class-d}
7-10
QoS
P13: Priority specification {priority | broadcast | multicast |
broadcast&multicast | unset}
priority: 0 to 7 (Multiple values can be specified.)
broadcast: broadcast
multicast: multicast
broadcast&multicast: bc+mc
unset: none
* For priority specification of classes A to D (P7, P9, P11, and P13), you can
specify broadcast/multicast/bc+mc respectively only once in one of classes
A to D. Also, you cannot specify other priorities in the class where
broadcast/multicast/bc+mc is specified.
* You cannot specify none for priority specification of classes A to D (P7, P9, P11, and
P13). Specify priority for any of classes A to D.
* The priority to be specified in any of classes A to D cannot be duplicated with the
priority specified in any other class. For example, you can set broadcast and
multicast in different classes but cannot set broadcast&multicast in a different class
because it is duplicated.
* The priority not specified in any of classes A to D does not belong to any class (No
Entry). Because a (No Entry) frame, frame that a priority does not belong to any
class, is not assigned to any classes, it becomes out of control and is discarded.
Default values
P11: 0,3
P13: 1,2
Usage conditions
You can set the priority mapping function in input VLAN units after setting the maximum
band limiting function in input VLAN units in the set qos in-rate maximum.
You cannot specify mode different from the mode set in the set qos in-rate maximum.
Notes
To inhibit a priority from belonging to a class, specify none explicitly. (You cannot
omit none.)
Selecting the default specification (initial) sets the value set in the set qos
initial-class-map in-maximum command.
Input examples
*Switch@1# set qos in-class-map maximum fe 1/5 vid 100 separate-red class-a
1,2,3 class-b 0,5-7 class-c broadcast class-d multicast
*Switch@1# set qos in-class-map maximum gbe 4/1 vid 100 separate class-a
0-4 class-b 5-7 class-c bc+mc class-d none
*Switch@1# set qos in-class-map maximum gbe 5/1 vid 100 initial
*Switch@1#
Output item
Related
commands
7-11
QoS
Privilege
General
Save
Synchronize
SBY execution
7-12
QoS
Parameters
7-13
QoS
When burst tolerance (lower threshold) for class A is specified in P7.
P8: Probability A (1 to 32)
P9: Burst tolerance (upper threshold) specification for class B
FE port: class-b 1 to 3000(Kbyte)
GbE port: class-b 1 to 30000(Kbyte)
P10: Burst tolerance (lower threshold) for class B or burst lower
threshold/probability disable {disable}
Burst tolerance (lower threshold) for class B
FE port: 1 to 2999(Kbyte)
GbE port: 1 to 29999(Kbyte)
disable: Burst lower threshold/probability disable
When burst tolerance (lower threshold) for class B is specified in P10.
P11: Probability B (1 to 32)
P12: Burst tolerance (upper threshold) specification for class C
FE port: class-c 1 to 3000(Kbyte)
GbE port: class-c 1 to 30000(Kbyte)
P13: Burst tolerance (lower threshold) for class C or burst lower
threshold/probability disable {disable}
Burst tolerance (lower threshold) for class C
FE port: 1 to 2999(Kbyte)
GbE port: 1 to 29999(Kbyte)
disable: Burst lower threshold/probability disable
When burst tolerance (lower threshold) for class C is specified in P13.
P14: Probability C (1 to 32)
P15: Burst tolerance (upper threshold) specification for class D
FE port: class-d 1 to 3000(Kbyte)
GbE port: class-d 1 to 30000(Kbyte)
P16: Burst tolerance (lower threshold) for class D or burst lower
threshold/probability disable {disable}
Burst tolerance (lower threshold) for class D
FE port: 1 to 2999(Kbyte)
GbE port: 1 to 29999(Kbyte)
disable: Burst lower threshold/probability disable
When burst tolerance (lower threshold) for class D is specified in P16.
P17: Probability D (1 to 32)
* If burst tolerance (upper/lower threshold) of classes A to D and probability
values (P6 to P17) are omitted, the values that are already set are
pre-retained.
Default values
7-14
QoS
Usage conditions
You can set the priority discard function in input VLAN units after setting the maximum
band limiting function in input VLAN units in the set qos in-rate maximum.
You cannot specify mode different from the mode set in the set qos in-rate maximum.
Notes
Input examples
*Switch@1# set qos in-priority maximum fe 1/1 vid 100 separate-red class-a
3000 20 4 class-b 1500 disable
*Switch@1# set qos in-priority maximum gbe 3/1 vid 70 separate-red class-c
48 disable class-d 8 1 32
*Switch@1# set qos in-priority maximum fe 1/8 vid 1000 separate-red class-a
127 disable class-b 64 disable class-c 3000 16 10 class-d 2000 8 5
*Switch@1# set qos in-priority maximum gbe 6/1 vid 100 separate class-a 1
class-b 1 class-c 127 class-d 127
*Switch@1# set qos in-priority maximum gbe 5/1 vid 100 initial
*Switch@1#
Output item
Related
commands
7-15
QoS
Privilege
General
Synchronize
SBY execution
Parameters
Default value
None
Usage condition
None
Note
None
7-16
QoS
Input example
7-17
QoS
Output items
Related
commands
7-18
QoS
Privilege
General
Save
Synchronize
SBY execution
Parameters
Default value
None
Usage condition
None
Notes
Input examples
Output item
7-19
QoS
Related
commands
7-20
QoS
Privilege
General
Save
Synchronize
SBY execution
- Specifying VLAN
set qos out-rate maximum P1 P2 P3 (vid) P4 P5 (maximum band limiting value)
- Specifying Remaining-VLAN
set qos out-rate maximum P1 P2 P3 (remain) P5 (maximum band limiting value)
- Specifying separate mode (specifying VLAN)
set qos out-rate maximum P1 P2 P3 (vid) P4 P5 (separate mode)
[P6] [P7] [P8] [P9]
- Specifying separate mode (specifying Remaining-VLAN)
set qos out-rate maximum P1 P2 P3 (remain) P5 (separate mode)
[P6] [P7] [P8] [P9]
Parameters
7-21
QoS
P5: Maximum band limiting value or separate mode {separate | separate-red}
Maximum band limiting value
FE port: 0 to 100000(Kbps)
GbE port: 0 to 1000000(Kbps)
* The setting granularity is 25(Kbps).
Separate mode
separate: Separate mode
separate-red: Separate mode (RED use)
When separate mode {separate | separate-red} is specified in P5.
P6: Maximum band limiting value of class A
FE port: class a 0 to 100000(Kbps)
GbE port: class a 0 to 1000000(Kbps)
P7: Maximum band limiting value of class B
FE port: class-b 0 to 100000(Kbps)
GbE port: class-b 0 to 1000000(Kbps)
P8: Maximum band limiting value of class C
FE port: class-c 0 to 100000(Kbps)
GbE port: class-c 0 to 1000000(Kbps)
P9: Maximum band limiting value of class D
FE port: class-d 0 to 100000(Kbps)
GbE port: class-d 0 to 1000000(Kbps)
* The setting granularity in P6 to P9 is 25(Kbps).
Default values
Usage conditions
The number of VLANs that can be registered on a corresponding port depends on the
maximum band limiting operation mode to be set. The following table shows the
number of VLANs that can be set for one port according to a specified maximum band
limiting operation mode.
Maximum band limiting
operation mode
FE port
GbE port
64
1024
128
2048
In output mode (in) and input/output mode (both), one place is used for
Remaining-VLAN among the number of settable VLANs.
Notes
If P6 to P9 are omitted, the values that are already set are pre-retained.
If P6 to P9 are omitted when maximum band limiting operation mode is switched, the
default values are set.
Input examples
*Switch@1# set qos out-rate maximum fe 3/7 vid 100 separate-red class-a 1000
class-b 2000
*Switch@1# set qos out-rate maximum gbe 5/1 vid VLAN200 separate class-c
3000 class-d 4000
*Switch@1# set qos out-rate maximum fe 1/7 vid 50 10000
*Switch@1#
7-22
QoS
Output item
Related
commands
7-23
QoS
Privilege
General
Save
Synchronize
SBY execution
- Specifying VLAN
set qos out-class-map maximum P1 P2 P3 (vid) P4 P6 (class-a) P7 P8 P9 P10 P11
P12 P13
- Specifying Remaining-VLAN
set qos out-class-map maximum P1 P2 P3 (remain) P6 (class-a) P7 P8 P9 P10 P11
P12 P13
- Specifying separate mode (specifying VLAN)
set qos out-class-map maximum P1 P2 P3 (vid) P4 P5 (separate mode) P6 (class-a)
P7 P8 P9 P10 P11 P12 P13
- Specifying separate mode (specifying Remaining-VLAN)
set qos out-class-map maximum P1 P2 P3 (remain) P5 (separate mode) P6 (class-a)
P7 P8 P9 P10 P11 P12 P13
- Specifying default (specifying VLAN)
set qos out-class-map maximum P1 P2 P3 (vid) P4 [P5 (separate)] P6 (initial)
- Specifying default (specifying Remaining-VLAN)
set qos out-class-map maximum P1 P2 P3 (remain) [P5 (separate)] P6 (initial)
- Specifying default (RED use) (specifying VLAN)
set qos out-class-map maximum P1 P2 P3 (vid) P4 P5 (separate-red) P6 (initial)
- Specifying default (RED use) (specifying Remaining-VLAN)
set qos out-class-map maximum P1 P2 P3 (remain) P5 (separate-red) P6 (initial)
7-24
QoS
Parameters
7-25
QoS
P8: Class B priority {class-b}
P9: Priority specification {priority | broadcast | multicast |
broadcast&multicast | unset}
priority: 0 to 7 (Multiple values can be specified.)
broadcast: broadcast
multicast: multicast
broadcast&multicast: bc+mc
unset: none
P10: Class C priority {class-c}
P11: Priority specification {priority | broadcast | multicast |
broadcast&multicast | unset}
priority: 0 to 7 (Multiple values can be specified.)
broadcast: broadcast
multicast: multicast
broadcast&multicast: bc+mc
unset: none
P12: Class D priority {class-d}
P13: Priority specification {priority | broadcast | multicast |
broadcast&multicast | unset}
priority: 0 to 7 (Multiple values can be specified.)
broadcast: broadcast
multicast: multicast
broadcast&multicast: bc+mc
unset: none
* For priority specification of classes A to D (P7, P9, P11, and P13), you can
specify broadcast/multicast/bc+mc respectively only once in one of classes A
to D. Also, you cannot specify other priorities in the class where
broadcast/multicast/bc+mc is specified.
* You cannot specify none for priority specification of classes A to D (P7, P9, P11, and
P13). Specify priority for any of classes A to D.
* The priority to be specified in any of classes A to D cannot be duplicated with the
priority specified in any other class. For example, you can set broadcast and multicast
in different classes but cannot set broadcast&multicast in a different class because it is
duplicated.
* The priority not specified in any of classes A to D does not belong to any class (No
Entry). Because a (No Entry) frame, frame that a priority does not belong to any class,
is not assigned to any classes, it becomes out of control and is discarded.
Default values
P11: 0,3
P13: 1,2
Usage conditions
You can set the priority mapping function in output VLAN units after setting the
maximum band limiting function in output VLAN units in the set qos out-rate maximum.
You cannot specify mode different from the mode set in the set qos out-rate maximum.
Notes
To inhibit a priority from belonging to a class, specify none explicitly. (You cannot
omit none.)
Selecting the default specification (initial) sets the value set in the set qos
initial-class-map out-maximum command.
7-26
QoS
Input examples
*Switch@1# set qos out-class-map maximum fe 1/5 vid 100 separate-red class-a
1,2,3 class-b 0,5-7 class-c broadcast class-d multicast
*Switch@1# set qos out-class-map maximum gbe 6/1 vid 100 separate class-a
bc+mc class-b none class-c 0-4 class-d 5-7
*Switch@1# set qos out-class-map maximum gbe 5/1 vid 100 class-a 0-1 class-b
2-3 class-c 4-5 class-d 6-7
*Switch@1#
Output item
Related
commands
7-27
QoS
Privilege
General
Save
Synchronize
SBY execution
7-28
QoS
Parameters
7-29
QoS
When burst tolerance (lower threshold) for class A is specified in P7.
P8: Probability A (1 to 32)
P9: Burst tolerance (upper threshold) specification for class B
FE port: class-b 1 to 3000(Kbyte)
GbE port: class-b 1 to 30000(Kbyte)
P10: Burst tolerance (lower threshold) for class B or burst lower
threshold/probability disable {disable}
Burst tolerance (lower threshold) for class B
FE port: 1 to 2999(Kbyte)
GbE port: 1 to 29999(Kbyte)
disable: Burst lower threshold/probability disable
When burst tolerance (lower threshold) for class B is specified in P10.
P11: Probability B (1 to 32)
P12: Burst tolerance (upper threshold) specification for class C
FE port: class-c 1 to 3000(Kbyte)
GbE port: class-c 1 to 30000(Kbyte)
P13: Burst tolerance (lower threshold) for class C or burst lower
threshold/probability disable {disable}
Burst tolerance (lower threshold) for class C
FE port: 1 to 2999(Kbyte)
GbE port: 1 to 29999(Kbyte)
disable: Burst lower threshold/probability disable
When burst tolerance (lower threshold) for class C is specified in P13.
P14: Probability C (1 to 32)
P15: Burst tolerance (upper threshold) specification for class D
FE port: class-d 1 to 3000(Kbyte)
GbE port: class-d 1 to 30000(Kbyte)
P16: Burst tolerance (lower threshold) for class D or burst lower
threshold/probability disable {disable}
Burst tolerance (lower threshold) for class D
FE port: 1 to 2999(Kbyte)
GbE port: 1 to 29999(Kbyte)
disable: Burst lower threshold/probability disable
When burst tolerance (lower threshold) for class D is specified in P16.
P17: Probability D (1 to 32)
* If burst tolerance (upper/lower threshold) of classes A to D and probability
values (P6 to P17) are omitted, the values that are already set are
pre-retained.
Default values
7-30
QoS
Usage conditions
You can set the priority discard function in output VLAN units after setting the maximum
band limiting function in output VLAN units in the set qos out-rate maximum.
You cannot specify mode different from the mode set in the set qos out-rate maximum.
Notes
Input examples
class-a
class-c
class-a
5
class-b
Output item
Related
commands
7-31
QoS
Privilege
General
Synchronize
SBY execution
Parameters
Default value
None
Usage condition
None
Note
None
7-32
QoS
Input example
7-33
QoS
Output Items
Related
commands
7-34
QoS
Privilege
General
Save
Synchronize
SBY execution
Parameters
Default value
None
Usage condition
None
Notes
Input examples
Output item
7-35
QoS
Related
commands
7-36
QoS
Privilege
General
Save
Synchronize
SBY execution
Parameters
Default value
P3: 1
Usage condition
None
Note
None
Input examples
Output item
Related
commands
7-37
QoS
Privilege
General
Synchronize
SBY execution
Parameter
P1: Port (line) number (Multiple values can be specified.) or line module number (1 to
12) (Multiple values can be specified.)
* If a port (line) number is specified in P1, the priority profile number set in the specified
port is shown.
* If a line module number is specified in P1, the priority profile number set in the
specified module is shown.
(You can specify a line module number only when the port type is ATM155, ATMP,
TDMP, ATMP155, or TDMP155.)
* If P1 is omitted, the priority profile numbers set in all the ports and those set in all the
line module numbers are shown.
Default value
None
Usage condition
None
Note
None
Input example
Output items
7-38
QoS
Related
commands
7-39
QoS
Privilege
General
Save
Synchronize
SBY execution
Input formats
Parameters
Default values
P7: 0,3
P9: 1,2
Usage condition
None
Notes
To inhibit a priority from belonging to a class, specify none explicitly. (You cannot
omit none.)
If the output-side fairness control mode function is disabled, class mapping does not
function.
7-40
QoS
Input examples
*Switch@1# set qos class-map profile 4 class-a none class-b 1,3,5 class-c
2,4,6 class-d 0,7
*Switch@1# set qos class-map profile 3 default
*Switch@1#
Output item
Related
commands
7-41
QoS
Privilege
General
Synchronize
SBY execution
Parameter
Default value
None
Usage condition
None
Note
None
Input example
Output items
Related
commands
7-42
QoS
Privilege
General
Save
Synchronize
SBY execution
- Specifying CoS
set qos cos-map profile P1 [P2 (index number)] P3 (cos) P4 P5 P6
- Specifying IPv4ToS / IPv6TC
set qos cos-map profile P1 [P2 (index number)] P3 (v4ToS/v6TC) P4 P5
- Specifying ether-type
set qos cos-map profile P1 [P2 (index number)] P3 (ether-type) P4 P5
- Specifying other
set qos cos-map profile P1 P2 (other) P3
7-43
QoS
Parameters
Default value
None
Usage condition
None
Notes
7-44
QoS
Input examples
*Switch@1#
*Switch@1#
*Switch@1#
*Switch@1#
*Switch@1#
*Switch@1#
*Switch@1#
set
set
set
set
set
set
qos
qos
qos
qos
qos
qos
cos-map
cos-map
cos-map
cos-map
cos-map
cos-map
profile
profile
profile
profile
profile
profile
10
10
10
10
10
10
2 cos inner 3 5
cos inner untag 7
v4tos fullbit 110 0
5 v6tc dscp 63 2
other 3
ether-type 0x8100 7
Output item
Related
commands
7-45
QoS
Privilege
General
Synchronize
SBY execution
Parameter
Default value
None
Usage condition
None
Note
None
Input example
Output items
7-46
QoS
Related
commands
7-47
QoS
Privilege
General
Save
Synchronize
SBY execution
Parameters
Default value
None
Usage condition
If command mode is safety mode, you cannot clear the profiles that are already mapped.
Notes
If P1 and P2 are omitted, execution is confirmed after this command has been entered.
If no profile is registered in the index number specified in P2, an error occurs.
No error occurs even if the profile number specified in P1 does not exist.
Input examples
Output item
Related
commands
7-48
QoS
Privilege
General
Save
Synchronize
SBY execution
Parameters
Default value
None
Usage condition
Note
None
Input examples
Output item
Related
commands
7-49
QoS
Privilege
General
Synchronize
SBY execution
Parameter
Default value
None
Usage condition
None
Note
None
Input example
Output items
Related
commands
7-50
QoS
Privilege
General
Save
Synchronize
SBY execution
Parameters
Default value
None
Usage condition
None
Note
Input examples
Output item
Related
commands
7-51
QoS
Privilege
General
Save
Synchronize
SBY execution
Parameters
Default value
None
Usage condition
Note
None
Input examples
Output item
Related
commands
7-52
QoS
Privilege
General
Synchronize
SBY execution
Parameter
Default value
None
Usage condition
None
Note
None
Input example
Output items
Related
commands
7-53
QoS
Privilege
General
Save
Synchronize
SBY execution
Parameters
Default value
None
Usage condition
None
Note
Input examples
*Switch@1# clear
*Switch@1# clear
*Switch@1# clear
Would you like to
*Switch@1#
Output item
Related
commands
7-54
QoS
Privilege
General
Save
Synchronize
SBY execution
Parameter
Default value
P1: disable
Usage condition
None
Note
None
Input example
Output item
Related
commands
7-55
QoS
Privilege
General
Synchronize
SBY execution
Parameter
None
Default value
None
Usage condition
None
Note
None
Input example
Output items
Related
commands
7-56
QoS
Privilege
General
Save
Synchronize
SBY execution
- Specifying VLAN
set qos out-priority fairness P1 (port (line) type) P2 P3 (vid) P4
[P5 (burst tolerance for class-a))] [P6] [P7] [P8]
- Specifying Remaining-VLAN
set qos out-priority fairness P1 (port (line) type) P2 P3 (remain)
[P5 (burst tolerance for class-a)] [P6] [P7] [P8]
- Specifying VLAN (ATM155/ATMP/TDMP/ATMP155/TDMP155)
set qos out-priority fairness P1 (line module number) P3 (vid) P4
[P5 (burst tolerance for class-a))] [P6] [P7] [P8]
- Specifying Remaining-VLAN (ATM155/ATMP/TDMP/ATMP155/TDMP155)
set qos out-priority fairness P1 (line module number) P3 (remain)
[P5 (burst tolerance for class-a))] [P6] [P7] [P8]
- Specifying default (specifying VLAN)
set qos out-priority fairness P1 (port (line) type) P2 P3 (vid) P4 P5 (initial)
- Specifying default (specifying Remaining-VLAN)
set qos out-priority fairness P1 (port (line) type) P2 P3 (remain) P5 (initial)
- Specifying default (specifying VLAN)
(ATM155/ATMP/TDMP/ATMP155/TDMP155)
set qos out-priority fairness P1 (line module number) P3 (vid) P4 P5 (initial)
- Specifying default (specifying Remaining-VLAN)
(ATM155/ATMP/TDMP/ATMP155/TDMP155)
set qos out-priority fairness P1 (line module number) P3 (remain) P5 (initial)
7-57
QoS
Parameters
P1: Port (line) type specification {fe | gbe} or line module number specification
fe: FE port
gbe: GbE port
Line module number: 3 to 10 (single specification)
* A line module number can be specified only when the port type is ATM155, ATMP,
TDMP, ATMP155, or TDMP155.
When a port (line) type is specified in P1.
P2: Port (line) number (single specification)
FE port: 1/1 to 4/8
GbE port: 3/1 to 10/1
P3: VLAN specification {vid} or Remaining-VLAN specification {remain}
vid: VLAN specification
remain: Remaining-VLAN specification
When vid is specified in P3.
P4: VLAN identifier {VLAN-ID | VLAN-name}
VLAN-ID: 1 to 4094 (Multiple values can be specified.)
VLAN-name: 1 to 32 characters
P5: Burst tolerance specification for class A {class-a 1 to 127} or default setting {initial}
Burst tolerance specification for class A: class-a 1 to 127(Kbyte)
initial: Default specification
When P5 is omitted or burst tolerance for class A is specified.
P6 Burst tolerance specification for class B {class-b 1 to 127}
class-b 1 to 127 (Kbyte)
P7: Burst tolerance specification for class C {class-c 1 to 127}
class-c 1 to 127 (Kbyte)
P8: Burst tolerance specification for class D {class-d 1 to 127}
class-d 1 to 127 (Kbyte)
* The granularity for burst tolerance is 1 (Kbyte).
* If burst tolerance specification for class A to class D (P5 to P8) are omitted, the current
values are kept.
Default value
Usage condition
If the output-side fairness control mode function is disable, you cannot set this function.
Note
None
Input examples
*Switch@1#
20
*Switch@1#
30
*Switch@1#
*Switch@1#
*Switch@1#
Output item
7-58
QoS
Related
commands
7-59
QoS
Privilege
General
Save
Synchronize
SBY execution
- Specifying VLAN
set qos out-weight rate P1 (port (line) type) P2 P3 (vid) P4 P5
- Specifying Remaining-VLAN
set qos out-weight rate P1 (port (line) type) P2 P3 (remain) P5
- Specifying VLAN (ATM155/ATMP/TDMP/ATMP155/TDMP155)
set qos out-weight rate P1 (line module number) P3 (vid) P4 P5
- Specifying Remaining-VLAN (ATM155/ATMP/TDMP/ATMP155/TDMP155)
set qos out-weight rate P1 (line module number) P3 (remain) P5
Parameters
P1: Port (line) type specification {fe | gbe} or line module number specification
fe: FE port
gbe: GbE port
Line module number: 3 to 10 (single specification)
* A line module number can be specified only when the port type is ATM155, ATMP,
TDMP, ATMP155, or TDMP15.
When a port (line) type is specified in P1.
P2: Port (line) number (single specification)
FE port: 1/1 to 4/8
GbE port: 3/1 to 10/1
P3: VLAN specification {vid} or Remaining-VLAN specification {remain}
vid: VLAN specification
remain: Remaining-VLAN specification
When vid is specified in P3.
P4: VLAN identifier {VLAN-ID | VLAN-name}
VLAN-ID: 1 to 4094 (Multiple values can be specified.)
VLAN-name: 1 to 32 characters
P6: Rate value
FE: 0 to 100000 (Kbps)
GbE, ATM155, ATMP, TDMP, ATMP155, TDMP155: 0 to 1000000 (Kbps)
* The granularity is 25 (Kbps).
Default value
None
Usage condition
If the output-side fairness control mode function is disable, you cannot set this function.
Note
If the GbE line mode function is se to FE in GbE-PV2, the maximum number of VLANs
that can be set for one port is the same as the maximum number of FE ports.
7-60
QoS
Input example
*Switch@1#
*Switch@1#
*Switch@1#
*Switch@1#
*Switch@1#
set
set
set
set
qos
qos
qos
qos
out-weight
out-weight
out-weight
out-weight
rate
rate
rate
rate
Output item
Related
commands
7-61
QoS
Privilege
General
Save
Synchronize
SBY execution
- Specifying VLAN
set qos out-weight fairness P1 (port (line) type) P2 P3 (vid) P4 P5
- Specifying Remaining-VLAN
set qos out-weight fairness P1 (port (line) type) P2 P3 (remain) P5
- Specifying VLAN (ATM155/ATMP/TDMP/ATMP155/TDMP155)
set qos out-weight fairness P1 (line module number) P3 (vid) P4 P5
- Specifying Remaining-VLAN (ATM155/ATMP/TDMP/ATMP155/TDMP155)
set qos out-weight fairness P1 (line module number) P3 (remain) P5
Parameters
P1: Port (line) type specification {fe | gbe} or line module number specification
fe: FE port
gbe: GbE port
Line module number: 3 to 10 (single specification)
* A line module number can be specified only when the port type is ATM155, ATMP,
TDMP, ATMP155, or TDMP155.
When a port (line) type is specified in P1.
P2: Port (line) number (single specification)
FE port: 1/1 to 4/8
GbE port: 3/1 to 10/1
P3: VLAN specification {vid} or Remaining-VLAN specification {remain}
vid: VLAN specification
remain: Remaining-VLAN specification
When vid is specified in P3.
P4: VLAN identifier {VLAN-ID | VLAN-name}
VLAN-ID: 1 to 4094 (Multiple values can be specified.)
VLAN-name: 1 to 32 characters
P5: Weight value (0 to 40000)
* The granularity is 1 (Weight).
* The default are fe, gbe, atm155, atmp, tdmp, atmp155, and tdmp155: 1 (Weight).
* Maximum number of registrations: gbe, atm155, atmp, tdmp, atmp155, and tdmp155
=2047(+1)/fe=255(+1)
(+1) is for Remaining-VLAN.
* Remaining-VLAN is registered when the output-side fairness control mode function is
enabled.
* You cannot clear Remaining-VLAN.
Default value
7-62
QoS
Usage condition
If the output-side fairness control mode function is disable, you cannot set this function.
Note
If the GbE line mode function is se to FE in GbE-PV2, the maximum number of VLANs
that can be set for one port is the same as the maximum number of FE ports.
Input examples
*Switch@1#
*Switch@1#
*Switch@1#
*Switch@1#
*Switch@1#
set
set
set
set
qos
qos
qos
qos
out-weight
out-weight
out-weight
out-weight
fairness
fairness
fairness
fairness
Output item
Related
commands
7-63
QoS
Privilege
General
Save
Synchronize
SBY execution
Parameters
P1: Port (line) type specification {fe | gbe} or line module number specification
fe: FE port
gbe: GbE port
Line module number: 3 to 10 (Multiple values can be specified.)
* A line module number can be specified only when the port type is ATM155, ATMP,
TDMP, ATMP155, or TDMP155.
When a port (line) type is specified in P1.
P2: Port (line) number (Multiple values can be specified.)
FE port: 1/1 to 4/8
GbE port: 3/1 to 10/1
P3: Rate value
FE: 1000 to 100000 (Kbps)
GbE, ATM155, ATMP, TDMP, ATMP155, TDMP155: 1000 to 1000000 (Kbps)
* The granularity is 1000 (Kbps).
Default values
P3: fe: 100(Mbps), gbe, atm155, atmp, tdmp, atmp155, tdmp155: 1(Gbps)
Usage condition
If the output-side fairness control mode function is disable, you cannot set this function.
Note
None
Input examples
Output item
7-64
QoS
Related
commands
7-65
QoS
Privilege
General
Synchronize
SBY execution
Parameters
7-66
QoS
Default value
None
Usage condition
None
Note
None
Input example
7-67
QoS
Output items
Related
commands
7-68
QoS
Privilege
General
Save
Synchronize
SBY execution
Parameters
P1: Port (line) type specification {fe | gbe} or line module number specification
fe: FE port
gbe: GbE port
Line module number: 3 to 10
* A line module number can be specified only when the port type is ATM155, ATMP,
TDMP, ATMP155, or TDMP155.
When a port (line) type is specified in P1.
P2: Port (line) number (single specification)
FE port: 1/1 to 4/8
GbE port: 3/1 to 10/1
P3: VLAN identifier {VLAN-ID | VLAN-name}
VLAN-ID: 1 to 4094 (single specification)
VLAN-name: 1 to 32 characters
* If P3 is omitted, the fairness control settings of all the VLANs registered in the
specified port are cleared.
Default value
None
Usage condition
None
Note
Input examples
Output item
7-69
QoS
Related
commands
7-70
QoS
Privilege
General
Save
Synchronize
SBY execution
- Setting default
set qos initial-class-map P1 P2 (default)
- Setting default priority mapping
set qos initial-class-map P1 P2 (class-a) P3 P4 P5 P6 P7 P8 P9
Parameters
7-71
QoS
Usage condition
None
Notes
Input examples
Output item
Related
commands
7-72
QoS
Privilege
General
Synchronize
SBY execution
Parameter
None
Default value
None
Usage condition
None
Notes
The default priority mapping of the maximum band limiting function of an input port is
shown.
The default priority mapping of the maximum band limiting function of an output port is
shown.
The default priority mapping of the multiport fairness control function is shown.
* Because the default priority mapping of the multiport fairness control function is
unsupported function, the default value is shown.
Input example
Output items
7-73
QoS
Related
commands
7-74
QoS
Privilege
General
Save
Synchronize
SBY execution
Parameters
7-75
QoS
When band specification (RED use) is specified in P1.
P2: Port (line) type {fe | gbe}
fe: FE port
gbe: GbE port
P3: Burst tolerance A (upper threshold) specification or device initial value
specification {default}
Burst tolerance A (upper threshold)
FE port: class-a 1 to 3000(Kbyte)
GbE port: class-a 1 to 30000(Kbyte)
default: Device initial value specification
When burst tolerance A (upper threshold) is specified in P3.
P4: Burst tolerance A (lower threshold) or probability disable {disable}
Burst tolerance A (lower threshold)
FE port: class-a 1 to 2999(Kbyte)
GbE port: class-a 1 to 29999(Kbyte)
disable: Probability disable
When burst tolerance A (lower threshold) is specified in P4.
P5: Probability A (1 to 32)
P6: Burst tolerance B (upper threshold)
FE port: class-b 1 to 3000(Kbyte)
GbE port: class-b 1 to 30000(Kbyte)
P7: Burst tolerance B (lower threshold) or probability disable {disable}
Burst tolerance B (lower threshold)
FE port: 1 to 2999(Kbyte)
GbE port: 1 to 29999(Kbyte)
disable: Probability disable
When burst tolerance B (lower threshold) is specified in P7.
P8: Probability B (1 to 32)
P9: Burst tolerance C (upper threshold)
FE port: class-c 1 to 3000(Kbyte)
GbE port: class-c 1 to 30000(Kbyte)
P10: Burst tolerance C (lower threshold) or probability disable {disable}
Burst tolerance C (lower threshold)
FE port: 1 to 2999(Kbyte)
GbE port: 1 to 29999(Kbyte)
disable: Probability disable
When burst tolerance C (lower threshold) is specified in P10.
P11: Probability C (1 to 32)
P12: Burst tolerance D (upper threshold)
FE port: class-d 1 to 3000(Kbyte)
GbE port: class-d 1 to 30000(Kbyte)
P13: Burst tolerance D (lower threshold) or probability disable {disable}
Burst tolerance D (lower threshold)
FE port: 1 to 2999(Kbyte)
GbE port: 1 to 29999(Kbyte)
disable: Probability disable
When burst tolerance D (lower threshold) is specified in P13.
P14: Probability D (1 to 32)
7-76
QoS
Default value
None
Usage
condition
None
Notes
You cannot set a value greater than the value set in P3 in P4. You cannot also set a
value greater than the values set in P3 in P6, P7, P9, P10, P12, and P13.
If command mode is safety mode, execution is confirmed after this command has been
entered.
Input example
Output item
Related
commands
7-77
QoS
Privilege
General
Synchronize
SBY execution
Parameter
None
Default value
None
Usage condition
None
Note
* Because the default burst tolerance of input-side fairness control function of multiport
(in-fairness) is unsupported function, the default value is shown.
Input example
Out-Maximum(FE)
7-78
QoS
===============
Maximum-Burst(KByte) Minimum-Burst(KByte) Probability
----------------------------------------------------------------------Class-A :
127
disabled
disabled
Class-B :
64
disabled
disabled
Class-C :
32
16
32(100%)
Class-D :
16
8
32(100%)
Out-Maximum(GbE)
================
Maximum-Burst(KByte) Minimum-Burst(KByte) Probability
----------------------------------------------------------------------Class-A :
127
disabled
disabled
Class-B :
64
disabled
disabled
Class-C :
32
16
32(100%)
Class-D :
16
8
32(100%)
*Switch@1#
Output items
Related
command
7-79
QoS
Privilege
General
Save
Synchronize
SBY execution
Parameter
Default value
P1:long
Usage condition
None
Note
None
Input examples
Output item
Related
command
7-80
QoS
Privilege
General
Synchronize
SBY execution
Parameter
None
Default value
None
Usage condition
None
Note
None
Input examples
Output items
Related
command
7-81
Switch Control
8 Switch Control
8-1
Switch Control
Privilege
General
Save
Synchronize
SBY execution
set frame-size
Setting of frame size
Sets a frame size.
Input format
set frame-size P1 P2
Parameters
Default value
P2: 1536
Usage condition
None
Notes
Tagbase VLAN port: Allowable frame size = Command specification value + 4 (Byte)
In a GbE line module for which the line module operation is set to FE, even if the value
set for the frame size exceeds 1536 bytes, it is dealt as 1536 bytes.
Input example
Output item
Related
command
show frame-size
8-2
Switch Control
Privilege
General
Synchronize
SBY execution
show frame-size
Display of frame size
Shows a frame size.
Input format
show frame-size
Parameter
None
Default value
None
Usage condition
None
Notes
Tagbase VLAN port: Allowable frame size = Command specification value + 4 (Byte)
Input example
Output items
Related
command
set frame-size
8-3
Switch Control
Privilege
General
Save
Synchronize
SBY execution
Parameter
Default value
Usage condition
None
Note
None
Input example
Output item
Related
command
8-4
Switch Control
Privilege
General
Synchronize
SBY execution
Parameter
None
Default value
None
Usage condition
None
Note
None
Input example
Output items
Related
command
8-5
Switch Control
Privilege
General
Synchronize
SBY execution
Parameter
Default value
None
Usage condition
None
Notes
When MAC learning information learned is shown in ATMP and TDMP line modules, of
the port (line) numbers in the same line module, the lowest port (line) number serves as
the pilot port (line) number, and the display is as follows.
- When specifying a port (line) number
All the MACs learned in the same line module are shown on the assumption that they
are learned using a pilot port (line) number. For this reason, even if a pilot port (line)
number and a specified port (line) number are different, the pilot port (line) number is
shown.
- When omitting a port (line) number
All the MACs learned in the same line module are shown on the assumption that they
are learned using a pilot port number.
* A pilot port (line) number is the lowest port (line) number in the same line module.
Input example
Output items
8-6
Switch Control
Related
commands
8-7
Switch Control
Privilege
General
Synchronize
SBY execution
Parameter
Default value
None
Usage condition
None
Note
None
Input example
Output items
VID: VLAN ID
Name: VLAN name
Learned-Entry: FDB learning count
Related
commands
8-8
Switch Control
Privilege
General
Synchronize
SBY execution
Parameter
None
Default value
None
Usage condition
None
Note
None
Input example
Output item
Related
commands
8-9
Switch Control
Privilege
General
Synchronize
SBY execution
Parameter
Default value
None
Usage condition
For ATMP and TDMP line modules, specify a pilot port (line) number only.
* A pilot port (line) number is the lowest port (line) number in the same line module.
Notes
None
Input example
Output items
Related
command
None
VID: VLAN ID
Name VLAN name
8-10
Switch Control
Privilege
General
Synchronize
SBY execution
Parameter
Default value
None
Usage condition
None
Notes
When MAC learning information learned is shown in ATMP and TDMP line modules, of
the port (line) numbers in the same line module, the lowest port (line) number serves as
the pilot port (line) number, and the display is as follows.
- When specifying a port (line) number
All the MACs learned in the same line module are shown on the assumption that they
are learned using a pilot port (line) number. For this reason, even if a pilot port (line)
number and a specified port (line) number are different, the pilot port (line) number is
shown.
- When omitting a port (line) number
All the MACs learned in the same line module are shown on the assumption that they
are learned using a pilot port number.
* A pilot port (line) number is the lowest port (line) number in the same line module.
Input example
Output items
Related
commands
VID: VLAN ID
Name: VLAN name
8-11
Switch Control
Privilege
General
Save
Synchronize
SBY execution
Parameter
Default value
None
Usage condition
None
Notes
Input example
Output item
Related
command
8-12
Switch Control
Privilege
General
Synchronize
SBY execution
Parameter
Default value
None
Usage condition
None
Notes
When MAC learning information learned is shown in ATMP and TDMP line modules, of
the port (line) numbers in the same line module, the lowest port (line) number serves as
the pilot port (line) number. All the MACs learned in the same line module are shown
on the assumption that they are learned using a pilot port number.
Input example
Output items
VID: VLAN ID
Name: VLAN name
Related
commands
8-13
Switch Control
Privilege
General
Save
Synchronize
SBY execution
Parameter
Default value
None
Usage condition
None
Note
None
Input example
Output item
Related
command
8-14
Switch Control
Privilege
General
Save
Synchronize
SBY execution
Parameter
Default value
P1: disable
Usage condition
None
Note
This function is valid only when the frame that flowed in from the port set in the portbase
VLAN goes out of the line set in the tagbase VLAN of the GbE line module.
Input example
Output item
Related
command
8-15
Switch Control
Privilege
General
Synchronize
SBY execution
Parameter
None
Default value
None
Usage condition
None
Note
None
Input example
Output items
Related
command
8-16
Route Control
9 Route Control
9-1
Route Control
Privilege
General
Save
Synchronize
SBY execution
set spantree
Setting of spanning tree protocol enable/disable support
Sets whether to enable or disable spanning tree protocol support.
Input format
set spantree P1
Parameter
Default value
P1: disable
Usage condition
None
Note
None
Input example
Output item
Related
command
9-2
Route Control
Privilege
General
Save
Synchronize
SBY execution
Parameter
Default value
P1: rstp
Usage condition
You can enter this command only when spanning tree protocol support is disabled.
Note
None
Input example
Output item
Related
commands
9-3
Route Control
Privilege
General
Synchronize
SBY execution
Parameter
None
Default value
None
Usage condition
None
Note
None
Input example
Output items
Related
command
9-4
Route Control
Privilege
General
Save
Synchronize
SBY execution
Parameter
P1: Priority
RSTP mode: 0 to 61440 (setting granularity: 4096)
STP mode: 0 to 65535
* If the priority is not a multiple of the setting granularity, this parameter results in an
error.
Default value
P1: 32768
Usage condition
None
Note
None
Input example
Output item
Related
command
9-5
Route Control
Privilege
General
Save
Synchronize
SBY execution
- Default specification
set spantree time P1 (default)
- Type setting (hello time/maximum aging time/forward delay time)
set spantree time P1 (hello | maxage | forward) P2
Parameters
Default values
P1: default
Hello time: 2 seconds
Maximum aging time: 20 seconds
Forward delay time: 15 seconds
Usage
conditions
Note
Input example
Output item
Related
command
9-6
Route Control
Privilege
General
Save
Synchronize
SBY execution
Parameter
Default value
P1: 3
Usage condition
None
Note
None
Input example
Output item
Related
command
9-7
Route Control
Privilege
General
Synchronize
SBY execution
Parameter
None
Default value
None
Usage condition
None
Note
None
Input example
9-8
Route Control
Output items
Related
commands
9-9
Route Control
Privilege
General
Save
Synchronize
SBY execution
Parameters
Default value
P2: disable
Usage condition
None
Note
Input example
Output item
Related
command
9-10
Route Control
Privilege
General
Save
Synchronize
SBY execution
Parameters
Default value
P2: 128
Usage condition
None
Note
None
Input example
Output item
Related
command
9-11
Route Control
Privilege
General
Save
Synchronize
SBY execution
Parameters
Default value
P2: auto
Usage condition
None
Note
When setting auto, the port cost value depends on the port speed.
- Actual default values when auto is set:
RSTP mode
STP mode
10Mbps: 2000000 10Mbps: 100
100Mbps: 200000 100Mbps: 19
1Gbps: 20000
1Gbps: 4
Input example
Output item
Related
command
9-12
Route Control
Privilege
General
Synchronize
SBY execution
Parameter
Default value
None
Usage condition
None
Note
None
Input example
128
128
128
128
128
disabled
disabled
disabled
disabled
disabled
disabled
disabled
disabled
disabled
disabled
auto
auto
auto
auto
auto
9-13
Route Control
8/1
0
9/1
0
10/1
0
11/1
0
12/1
0
discarding disabled
200000 800000004cb47c7f
0 8039
discarding disabled
200000 800000004cb47c7f
0 8041
discarding disabled
200000 800000004cb47c7f
0 8049
discarding disabled
200000 800000004cb47c7f
0 8051
discarding disabled
200000 800000004cb47c7f
0 8059
*Switch@1#
Output items
Related
commands
9-14
Route Control
Privilege
General
Save
Synchronize
SBY execution
Parameters
Default value
P2: disable
Usage condition
None
Note
None
Input example
Output item
Related
commands
9-15
Route Control
Privilege
General
Synchronize
SBY execution
Parameter
Default value
None
Usage condition
None
Note
None
Input example
Output items
Related
command
9-16
Route Control
Privilege
General
Save
Synchronize
SBY execution
Parameters
Default value
P2: auto
Usage conditions
If the port is full duplex when auto is set in P2, point-to-point setting is enabled.
Note
None
Input example
Output item
Related
command
9-17
Display of point-to-point
Route Control
Privilege
General
Synchronize
SBY execution
Parameter
Default value
None
Usage condition
None
Note
None
Input example
9-18
Route Control
Output items
Related
command
Setting of point-to-point
9-19
Route Control
Privilege
General
Save
Synchronize
SBY execution
Parameters
Default value
P3: disable
Usage conditions
To enable the BPDU transparency function, enable the spanning tree function. If the
BPDU transparency function is enabled when the spanning tree function is enabled, the
BPDUs to be made transparent are excluded from the spanning tree function.
Notes
The frames to which this function is to be applied are frames that comply with
IEEE802.1D and have the destination MAC address 01:80:C2:00:00:00.
Tagged BPDU reception does not comply with IEEE802.1D but the appropriate switch
is supported.
Input example
Output item
Related
command
9-20
Route Control
Privilege
General
Synchronize
SBY execution
Parameter
None
Default value
None
Usage condition
None
Note
None
Input example
Output item
BPDU Transparent VID: All VLAN IDs set as the BPDU transparency function
Related
command
9-21
Route Control
Privilege
General
Save
Synchronize
SBY execution
Parameters
Default value
P3 : disable
Usage condition
None
Note
None
Input examples
Output item
Related
command
9-22
Route Control
Privilege
General
Synchronize
SBY execution
Parameter
Default value
None
Usage condition
None
Note
None
Input example
Output items
Related
command
9-23
Route Control
Privilege
General
Save
Synchronize
SBY execution
Parameters
Default values
Usage condition
None
Note
Input example
Output item
Related
command
9-24
Route Control
Privilege
General
Synchronize
SBY execution
Parameter
Default value
None
Usage condition
None
Note
None
Input example
9-25
Route Control
Output items
Related
command
9-26
Route Control
Privilege
General
Save
Synchronize
SBY execution
Parameter
Default value
None
Usage condition
None
Note
Clearing a group by specifying its group name requires that the group name be
registered in the set link aggregation in advance.
Input example
Output item
Related
command
9-27
Route Control
Privilege
General
Save
Synchronize
SBY execution
Parameter
Default value
P1: 32768
Usage condition
If a link aggregation group is already set in the device, you are not allowed to set the
system priority.
Note
None
Input example
Output item
Related
command
9-28
Route Control
Privilege
General
Synchronize
SBY execution
Parameter
None
Default value
None
Usage condition
None
Note
None
Input example
Output item
Related
command
9-29
Route Control
Privilege
General
Save
Synchronize
SBY execution
Parameters
Default value
P2: 128
Usage condition
Setting for a port to which the link is down in the link aggregation group cannot be
allowed.
Note
None
Input example
Output item
Related
command
9-30
Route Control
Privilege
General
Synchronize
SBY execution
Parameter
Default value
None
Usage condition
None
Notes
Input example
Output items
Related
command
9-31
Route Control
Privilege
General
Save
Synchronize
SBY execution
Parameters
Default value
P2: 0
Usage condition
None
Note
The link aggregation protection time function is effective for the link aggregation group
that operates in simple aggregation and for which standby-admit is set.
Input example
Output item
Related
command
9-32
Route Control
Privilege
General
Synchronize
SBY execution
Parameter
Default value
None
Usage condition
None
Note
None
Input example
Output items
Related
command
9-33
Route Control
Privilege
General
Save
Synchronize
SBY execution
set igmp
Setting of IGMP Snooping function enable/disable
Sets whether to enable or disable the IGMP Snooping function.
Input formats
Parameters
Default value
P1: disable
Usage condition
None
Note
None
Input example
Output item
Related
command
9-34
Route Control
Privilege
General
Synchronize
SBY execution
Parameter
None
Default value
None
Usage condition
None
Note
None
Input example
Output items
Related
command
set igmp
9-35
Route Control
Privilege
General
Synchronize
SBY execution
Parameter
Default value
None
Usage condition
None
Note
None
Input example
Output items
Related
command
None
9-36
Route Control
Privilege
General
Save
Synchronize
SBY execution
Parameters
Default value
None
Usage condition
None
Note
None
Input example
Output item
Related
commands
set igmp
show igmp status
clear igmp vid
9-37
Route Control
Privilege
General
Synchronize
SBY execution
Parameter
Default value
None
Usage condition
None
Note
None
Input example
Output items
Related
command
None
9-38
Route Control
Privilege
General
Synchronize
SBY execution
Parameter
Default value
None
Usage condition
None
Note
None
Input example
Output items
IGMP Group Ports: Port (line) number registered as the multicast entry
IGMP Group Address: IGMP Snooping MAC address
VLAN ID: VLAN ID
Total Number of Ports: Number of ports (lines allocated to the same group
Related
command
None
9-39
Route Control
Privilege
General
Save
Synchronize
SBY execution
Parameter
Default value
None
Usage condition
None
Note
None
Input example
Output item
Related
commands
set igmp
show igmp status
clear igmp mac
9-40
Filters
10 Filters
10-1
Filters
Privilege
General
Save
Synchronize
SBY execution
Parameters
P1: Receiving line number (Multiple values can be specified.) or receiving line module
number (Multiple values can be specified.)
P2: Destination line number (Multiple values can be specified.) or destination line
module number (Multiple values can be specified.)
P3: Enable/disable setting {enable | disable}
enable: Enable setting
disable: Disables setting
Default values
All the destination line numbers are disabled that correspond to all the receiving line
numbers.
Usage conditions
You cannot simultaneously set a receiving line number and a receiving line module
number in P1.
You cannot simultaneously set a destination line number and a destination line module
number in P2.
If the line module type is ATMP, TDMP, or GbE-MUX, only the line module number can
be specified.
If the line module type is other than the above, only the line number can be specified.
Notes
Specifying enable in P3 disables transfer of the inflow frame from the specified receiving
line to the specified destination line.
If enable is specified, the configuration that is already set is not affected because the
destination line number or destination line module number specified in P2 is added to
the receiving line number or receiving line module number specified in P1.
If disable is specified, the other configurations that are already set are not affected
because only the destination line number or destination line module number in P2
corresponding to the receiving line number or receiving line module number specified in
P1 is disabled.
Input example
Output item
Related
command
10-2
Filters
Privilege
General
Synchronize
SBY execution
Parameter
Default value
None
Usage condition
None
Note
None
Input example
Output items
Related
command
10-3
Filters
Privilege
General
Save
Synchronize
SBY execution
- Setting other
set filter profile P1 P2 (other) P3
- Selecting dest-mac/src-mac in the filter setting
set filter profile P1 [P2 (index number)] P3 P4 (dest-mac | src-mac) P5 P6
- Selecting ether-type in the filter setting
set filter profile P1 [P2 (index number)] P3 P4 (ether-type) P5
- Selecting proto-type in the filter setting
set filter profile P1 [P2 (index number)] P3 P4 (proto-type) P5
- Selecting dest-ip/src-ip in the filter setting
set filter profile P1 [P2 (index number)] P3 P4 (dest-ip | src-ip) P5 P6
Parameters
10-4
Filters
When dest-ip or src-ip is selected in P4
P5: IP address
P6: Net mask
Default value
None
Usage condition
None
Note
You can set overwrite for a registered index but cannot reregister the index.
Input examples
Output item
Related
commands
10-5
Filters
Privilege
General
Synchronize
SBY execution
Parameter
Default value
None
Usage condition
None
Note
None
Input example
10-6
Filters
Output items
Related
commands
10-7
Filters
Privilege
General
Save
Synchronize
SBY execution
Parameters
Default value
None
Usage condition
If command mode is safety mode, you cannot clear the profiles that are already mapped.
Notes
If P1 and P2 are omitted, execution is confirmed after this command has been entered.
If the index number specified in P2 is not registered, an error occurs.
No error occurs even if the profile number specified in P1 does not exist.
Input example
Output item
Related
commands
10-8
Filters
Privilege
General
Save
Synchronize
SBY execution
Parameters
Default value
None
Usage condition
Note
None
Input examples
Output item
Related
commands
10-9
Filters
Privilege
General
Synchronize
SBY execution
Parameters
Default value
None
Usage condition
None
Note
None
Input example
Output items
10-10
Filters
Related
commands
10-11
Filters
Privilege
General
Save
Synchronize
SBY execution
Parameters
Default value
None
Usage condition
None
Note
Input examples
in-port fe 1/1 10
in-port gbe 6/1 VLAN100
in-port gbe 6/1
the configuration? :(Y/N): y
in-port atm 3/1 2
Output item
Related
commands
10-12
Filters
Privilege
General
Save
Synchronize
SBY execution
Parameters
Default value
None
Usage condition
Note
None
Input examples
Output item
Related
commands
10-13
Filters
Privilege
General
Synchronize
SBY execution
Parameters
Default value
None
Usage condition
None
Note
None
Input example
Output items
10-14
Filters
Related
commands
10-15
Filters
Privilege
General
Save
Synchronize
SBY execution
Parameters
Default value
None
Usage condition
None
Note
Input examples
out-port fe 1/1 20
out-port gbe 6/1 VLAN100
out-port gbe 6/1
the configuration? :(Y/N): y
out-port atm 3/1 200
Output item
Related
commands
10-16
Filters
Privilege
General
Save
Synchronize
SBY execution
Parameters
Default value
None
Usage condition
None
Notes
You can register up to 8192 counts for MAC address learning limit per line module.
If a Static MAC address is already registered, you cannot change the MAC address
learning limiting count.
Input examples
*Switch@1#
*Switch@1#
*Switch@1#
*Switch@1#
*Switch@1#
set
set
set
set
fdb
fdb
fdb
fdb
limiter
limiter
limiter
limiter
fe 1/1 100 11
gbe 3/1 VLAN 200 7
gbe 5/1 VLAN 200 32
atm 7/1 VLAN 300 64
Output item
Related
commands
10-17
Filters
Privilege
General
Synchronize
SBY execution
Parameters
Default value
None
Usage condition
None
Note
None
Input example
10-18
Filters
MAC Limiter Port Static Address Table
=====================================
Port VID Static-MAC Address
-----------------------------------------------------------------4/1
1 00:00:00:00:00:01
6/1 100 00:00:00:00:00:02
*Switch@1#
Output items
Related
commands
10-19
Filters
Privilege
General
Save
Synchronize
SBY execution
Parameters
Default value
None
Usage condition
None
Notes
Input examples
Output item
Related
commands
10-20
Filters
Privilege
General
Save
Synchronize
SBY execution
Parameters
Default value
None
Usage condition
If no MAC address learning count limiting function is set, you cannot set this function.
Note
You can register up to 16 static MAC addresses of MAC address learning count limiting
functions per VLAN.
Input examples
Output item
Related
commands
10-21
Filters
Privilege
General
Save
Synchronize
SBY execution
Parameters
Default value
None
Usage condition
None
Note
Input examples
Output item
Related
commands
10-22
EtherOAM
11 EtherOAM
11-1
EtherOAM
Privilege
General
Save
Synchronize
SBY execution
Parameters
Default value
P1: 1s
Usage condition
You cannot register the same MEG ID to two or more MEG indexes. If the specified
MEG ID has already been registered, an error occurs.
If the MEP data of the specified MEG index exists, you cannot execute update.
Note
None
Input example
Output item
Related
commands
11-2
EtherOAM
Privilege
General
Synchronize
SBY execution
Parameter
Default value
None
Usage condition
None
Note
None
Input example
11-3
EtherOAM
Output items
Related
commands
Setting of MEG
Clearing of MEG
11-4
EtherOAM
Privilege
General
Save
Synchronize
SBY execution
Parameter
Default value
None
Usage
conditions
If the MEP data of the specified MEG index exists, you cannot clear it.
Note
None
Input example
Output item
Related
commands
Setting of MEG
Display of MEG setting information
Setting of MEP
Display of MEP setting information
11-5
EtherOAM
Privilege
General
Save
Synchronize
SBY execution
Parameters
Default value
None
Usage
conditions
If the line module type of the specified port (line) number is ATMP155 or TDMP155, you
must disable APS.
If the MEG data of the specified MEG index does not exist, or if the MEP data of the
specified MEP index has already been registered, you cannot execute registration.
If the MEG data transmission period of the specified MEG index is 3.33ms or 100ms,
your can register MEP only when the line module type is GbE-PV2.
If you specify untag for the tagbase VLAN port, you must specify outside for the
transmission direction.
If the line module type of the specified port (line) number is
ATMP/TDMP/ATMP155/TDMP155, you must specify inside for the transmission
direction.
If redundant configuration by EtherPS is set for the specified port (line) number, the
following cannot be set.
- inside MEP setting
- multiple MEP settings
- Untag MEP setting
- MEP setting on a VLAN other than the one when EtherPS control VLAN is set
- MEP setting with MEG LEVEL other than the one when EtherPS control VLAN is set
If EtherPS control VLAN is registered for the specified port (line) number, set the same
value for VLAN and MEG level.
If the line module type of the specified port (line) number is TDMP or TDMP155, the line
mode must have been set.
You can register the maximum number of MEPs per line module (the maximum number
of MEPs: GbE-PV2 [EtherPS disabled] [64], GbE-PV2 [EtherPS enabled] [1], ATMP
[64], TDMP [64], ATMP155 [128], TDMP155 [128]). If the line module type is
ATMP/TDMP/ATMP155/TDMP155, however, you can register only one MEP per VLAN.
11-6
EtherOAM
Notes
The specified VLAN ID must have been set for the specified port (line).
If the VLAN tag swapping is set for the specified port (line) number, execute this setting
specifying the swapping destination VLAN ID.
Input example
Output item
Related
commands
Setting of MEG
Clearing of MEG
Display of MEP setting information
Clearing of MEP
Setting of associated MEP ID
Setting of test target MEP
11-7
EtherOAM
Privilege
General
Synchronize
SBY execution
Parameters
Default value
None
Usage condition
None
Note
None
Input example
11-8
EtherOAM
Ether OAM Peer MEP Information
==============================
Peer MEP ID Condition RDI-Received
-----------------------------------10
normal
rdi
28
loc
no-rdi
7001
loc
no-rdi
*Switch@1# show ether-oam mep index
Ether OAM MEP Information
=========================
MEP Index Port
VID MEG Level MEG Index MEG ID
Position MEP ID
CC Priority Transmit Receive
Kind
DES MAC Address
RDI
----------------------------------------------------------------------10 1/1
20
3
2 TEST000000002 outside
180
7
disabled enabled
----enabled
*Switch@1#
Output items
Related
commands
Setting of MEG
Clearing of MEG
Setting of MEP
Clearing of MEP
Setting of associated MEP ID
Clearing of associated MEP ID
Setting of EtherOAM Continuity Check transmission
Setting of RDI operation
11-9
EtherOAM
Privilege
General
Save
Synchronize
SBY execution
Parameter
Default value
None
Usage condition
None
Notes
If the associated MEP ID has been registered for the specified MEP index, the setting of
the associated MEP ID is also cleared when the MEP index is cleared.
If the specified MEP index has been registered as a test target MEP, the setting of the
test target MEP is also cleared when the MEP index is cleared.
During ETH-CCM operation (either of sending or receiving is currently enabled), the
MEP of the specified MEP index cannot be cleared.
Input example
Output item
Related
commands
Clearing of MEG
Setting of MEP
Display of MEP setting information
Setting of associated MEP ID
Clearing of associated MEP ID
Setting of test target MEP
Clearing of test target MEP
11-10
EtherOAM
Privilege
General
Save
Synchronize
SBY execution
set ether-oam lm
Setting of test target MEP
Sets a test target MEP.
Input format
Parameters
Default value
P2: all
Usage
conditions
If the MEP data of the specified MEP index has not been registered, you cannot execute
registration.
If the test target MEP has already been registered, you cannot execute registration.
Note
None
Input example
Output item
Related
commands
Setting of MEG
Clearing of MEG
Setting of MEP
Clearing of MEP
Display of test target MEP
Clearing of test target MEP
11-11
EtherOAM
Privilege
General
Synchronize
SBY execution
show ether-oam lm
Display of test target MEP setting information
Shows the test target MEP setting information.
Input format
show ether-oam lm
Parameter
None
Default value
None
Usage condition
None
Note
None
Input example
Output items
Related
commands
Setting of MEG
Clearing of MEG
Setting of MEP
Clearing of MEP
Setting of test target MEP
Clearing of test target MEP
11-12
EtherOAM
Privilege
General
Save
Synchronize
SBY execution
clear ether-oam lm
Clearing of test target MEP
Clears a test target MEP.
Input format
clear ether-oam lm
Parameter
None
Default value
None
Usage condition
None
Note
None
Input example
Output item
Related
commands
Setting of MEG
Clearing of MEG
Setting of MEP
Clearing of MEP
Setting of test target MEP
Display of test target MEP setting information
11-13
EtherOAM
Privilege
General
Save
Synchronize
SBY execution
Parameters
Default value
P3: receive-enable
Usage
conditions
If the MEP data of the specified MEP index has not been registered, you cannot execute
registration. Also, if the line module is other than GbE-PV2/ATMP/TDMP/ATMP155/
TDMP155, you cannot execute registration.
The maximum number of the associated MEPs can be registered for every line module
[the maximum number of the associated MEPs: GbE-PV2 (256), ATMP (64), and TDMP
(64)] per port of a line (1 port).
You can register the maximum number of associated MEPs per line module (the
maximum number of associated MEPs: GbE-PV2 [EtherPS disabled] [1024], GbE-PV2
[EtherPS enabled] [1], ATMP [64], TDMP [64], ATMP155 [128], TDMP155 [128]). If the
line module type is ATMP/TDMP/ATMP155/TDMP155, however, you can register only
one associated MEP per MEP
Note
To enable CCM receiving monitoring, you must set receive-enable for ETH-CC
transmission setting to allow receiving.
Input example
Output item
Related
commands
Setting of MEG
Clearing of MEG
Setting of MEP
Display of MEP setting information
Clearing of MEP
Clearing of associated MEP ID
11-14
EtherOAM
Privilege
General
Save
Synchronize
SBY execution
Parameters
Default value
None
Usage condition
You can clear the associated MEP ID of the specified MEP index only in the following
conditions. Otherwise, you cannot clear it.
Conditions:
[1] If the receiving setting of the own MEP is disabled, all the associated MEP ID of the
own MEP can be cleared.
[2] If the receiving setting of the own MEP is enabled and that of an associated MEP is
disabled, only the associated MEP of the own MEP can be cleared.
Note
None
Input example
Output item
Related
commands
Setting of MEG
Clearing of MEG
Setting of MEP
Display of MEP setting information
Clearing of MEP
Setting of associated MEP ID
11-15
EtherOAM
Privilege
General
Save
Synchronize
SBY execution
Parameters
Default value
None
Usage
conditions
If the MIP data of the specified MIP index has already been registered, you cannot
execute registration.
If the maximum number of the MIP data shown below has already been registered for
the specified port (line) number, you cannot execute registration:
Up to 8 MIPs can be registered per port. Up to 4094 VLANs can be specified for one
MIP.
Only the GbE-PV2 card can operate.
Notes
The specified VLAN ID must have been set for the specified port (line).
If the VLAN tag swapping is set for the specified port (line) number, execute this setting
specifying the swapping destination VLAN ID.
Input example
Output item
Related
commands
Setting of MEG
Clearing of MEG
Display of MIP setting information
Clearing of MIP
11-16
EtherOAM
Privilege
General
Synchronize
SBY execution
Parameters
Default value
None
Usage condition
None
Note
None
Input example
11-17
EtherOAM
Output items
Related
commands
Setting of MEG
Clearing of MEG
Setting of MIP
Clearing of MIP
11-18
EtherOAM
Privilege
General
Save
Synchronize
SBY execution
Parameters
Default value
None
Usage condition
None
Note
None
Input example
Output item
Related
commands
Setting of MEG
Clearing of MEG
Setting of MIP
Display of MIP setting information
11-19
EtherOAM
Privilege
General
Save
Synchronize
SBY execution
Parameters
Default values
P1: 01:80:c2:00:00:30
P2: 0x8902
Usage condition
None
Note
Execute this setting before performing ETH-CC, ETH-LB, and ETH-LT tests.
The following MAC addresses cannot be set in P1.
01:00:5E:00:00:00 - 01:00:5E:7F:FF:FF
01:80:C2:00:00:00 - 01:80:C2:00:00:2F
Input example
*Switch@1# set ether-oam frame 01 :02 :03 :04 :05 :06 0x0600
*Switch@1#
Output item
Related
commands
11-20
EtherOAM
Privilege
General
Synchronize
SBY execution
Parameter
None
Default value
None
Usage condition
None
Note
None
Input example
Output items
Multicast MAC address(class1): Destination Multicast MAC for Ether CC/LB frame
Multicast MAC address(class2): Destination Multicast MAC for Ether LT frame
Protocol type: Protocol type
Related
command
11-21
EtherOAM
Privilege
General
Save
Synchronize
SBY execution
Parameters
Default values
Usage condition
None
Note
Input example
Output item
Related
command
11-22
EtherOAM
Privilege
General
Synchronize
SBY execution
Parameter
None
Default value
None
Usage condition
None
Note
None
Input example
Output items
Related
command
11-23
EtherOAM
Privilege
General
Save
Synchronize
SBY execution
set ether-oam cc
Setting of EtherOAM Continuity Check transmission
Sets the transmission of EtherOAM Continuity Check.
Input formats
- Starting transmission
set ether-oam cc P1 P2 (transmit-enable) [P3] P4 [P5]
- Stopping transmission
set ether-oam cc P1 P2 (transmit-disable) P3
Parameters
Default values
P2: transmit-disable
P4: receive-disable
P5: 7
Usage condition
If the MEP data of the specified MEP index has not been registered, you cannot execute
this setting.
Note
None
Input example
Output item
11-24
EtherOAM
Related
commands
Setting of MEG
Clearing of MEG
Setting of MEP
Display of MEP setting information
Clearing of MEP
11-25
EtherOAM
Privilege
General
Save
Synchronize
SBY execution
Parameters
Default value
P2: disable
Usage condition
If the MEP data of the specified MEP index has not been registered, you cannot execute
registration.
Note
Input example
Output item
Related
commands
Setting of MEG
Clearing of MEG
Setting of MEP
Display of MEP setting information
Clearing of MEP
Setting of Ether-OAM Continuity Check transmission
11-26
EtherOAM
Privilege
General
Synchronize
SBY execution
Parameter
None
Default value
None
Usage condition
None
Note
None
Input example
Output items
Date: Date
Fault: Fault information
MEP INDEX: MEP index
Related
command
None
11-27
EtherOAM
Privilege
General
Synchronize
SBY execution
Parameter
Default value
None
Usage condition
None
Note
None
Input example
11-28
EtherOAM
Output items
Related
command
11-29
EtherOAM
Privilege
General
Save
Synchronize
SBY execution
Parameter
Default value
None
Usage condition
None
Note
None
Input example
Output item
Related
command
11-30
EtherOAM
Privilege
General
Save
Synchronize
SBY execution
loopback ether-oam
Starting of EtherOAM Loop Back test
Executes ETH-LB transmission.
Input format
Parameters
Default values
P3: 4
P4: 1
P5: 46
P6: 7
Usage
conditions
If the MEP data of the specified MEP index does not exist, you cannot execute this
command.
You cannot activate two or more of this command simultaneously. Also, you cannot
activate this command and any/all of the ETH-LT transmission command, the ETH-DM
transmission command, or/and the ETH-LM transmission command simultaneously.
For a GbE-PV2 line module, a value exceeding 1518 cannot be specified in P5.
Note
None
11-31
EtherOAM
Input example
ok
ok
ok
ok
result
result
result
result
ok
ok
ok
ok
00:30:13:41:77:70
00:30:13:41:77:70
00:30:13:41:77:70
00:30:13:41:77:70
seq=1
seq=2
seq=3
seq=4
bytes=46
bytes=46
bytes=46
bytes=46
time<5ms
time<5ms
time<5ms
time<5ms
test
test
test
test
Output items
Related
commands
Setting of MEG
Clearing of MEG
Setting of MEP
Clearing of MEP
11-32
EtherOAM
Privilege
General
Save
Synchronize
SBY execution
linktrace ether-oam
Starting of EtherOAM Link Trace test
Executes ETH-LT transmission.
Input format
Parameters
Default values
P3: 5s
P4: 255
P5: 7
Usage
conditions
If the MEP data of the specified MEP index does not exist, you cannot execute this
command.
You cannot activate two or more of this command simultaneously. Also, you cannot
activate this command and any/all of the ETH-LB transmission command, the ETH-DM
transmission command, or/and the ETH-LM transmission command simultaneously.
Note
None
11-33
EtherOAM
Input example
Output items
Related
commands
Setting of MEG
Clearing of MEG
Setting of MEP
Clearing of MEP
11-34
EtherOAM
Privilege
General
Save
Synchronize
SBY execution
dm ether-oam
Starting of EtherOAM Frame Delay Measurement test
Executes ETH-DM transmission.
Input format
Parameters
Default values
P3: 4
P4: 1
P5: 7
Usage
conditions
If the MEP data of the specified MEP index does not exist, you cannot execute this
command.
You cannot activate two or more of this command simultaneously. Also, you cannot
activate this command and any/all of the ETH-LB transmission command, the ETH-LT
transmission command, or/and the ETH-LM transmission command simultaneously.
Note
None
11-35
EtherOAM
Input example
Output items
Related
commands
Setting of MEG
Clearing of MEG
Setting of MEP
Clearing of MEP
11-36
EtherOAM
Privilege
General
Save
Synchronize
SBY execution
lm ether-oam
Starting of EtherOAM Loss Measurement test
Executes ETH-LM transmission.
Input format
Parameters
Default values
P3: 4
P4: 1
P5: 7
Usage
conditions
If the test target MEP data of the specified MEP index does not exist, you cannot
execute this command.
You cannot activate two or more of this command simultaneously. Also, you cannot
activate this command and any/all of the ETH-LB transmission command, the ETH-LT
transmission command, or/and the ETH-DM transmission command simultaneously.
Note
None
11-37
EtherOAM
Input example
Output items
11-38
EtherOAM
Related
commands
Setting of MEG
Clearing of MEG
Setting of MEP
Clearing of MEP
Setting of test target MEP
Clearing of test target MEP
11-39
EtherOAM
Privilege
General
Save
Synchronize
SBY execution
set ether-ps
Setting of EtherPS enable/disable
Sets whether to enable or disable the EtherPS function.
Input formats
- Enabling EtherPS
set ether-ps P1 P2 (enable) P3 P4 P5
- Disabling EtherPS
set ether-ps P1 P2 (disable)
Parameters
P1: Port (line) number (single specification) {1/1 | 2/1 | 5/1 | 6/1 | 9/1 | 10/1}
P2: EtherPS function enable/disable setting {enable | disable}
enable: Enables EtherPS function
disable: Disables EtherPS function
When enable is specified in P2
P3: Switchover method {1:1}
1:1: 1:1 method
P4: Direction {bi}
bi: bi-directional
P5: Switchback mode {revertive | non-revertive}
revertive: Automatic switchback
non-revertive: Manual switchback
Default value
P2: disable
Usage
conditions
If two or more MEPs have been registered, the MEP transmission direction is other than
outside, or the VLAN of the MEP is registered with Untag specification to the specified
port (line) number, you cannot execute this setting. If two or more associated MEPs
are set for the registered MEP, you cannot execute this setting.
If a link aggregation group is set or the spanning tree port is enabled for the specified
port (line) number, this command cannot be set.
Notes
Input example
Output item
11-40
EtherOAM
Related
commands
11-41
EtherOAM
Privilege
General
Save
Synchronize
SBY execution
Parameters
P1: Port (line) number (single specification) {1/1 | 2/1 | 5/1 | 6/1 | 9/1 | 10/1}
P2: EtherPS control VLAN enable/disable setting {enable | disable}
enable: Enables EtherPS control VLAN
disable: Disables EtherPS control VLAN
When enable is specified in P2
P3: Control VLAN (1 to 4094)
P4: MEG level (0 to 7)
P5: Priority (0 to 7)
* If P5 is omitted, 7 is assumed.
Default values
P2: disable
P5: 7
Usage
conditions
If EtherPS of the specified port (line) number is not enabled, you cannot execute this
setting.
If MEP has been registered for the specified port (line) number, set the same value for
Control VLAN and MEG level.
Note
Input example
Output item
Related
commands
set ether-ps
show ether-ps config
11-42
EtherOAM
Privilege
General
Save
Synchronize
SBY execution
Parameters
P1: Port (line) number (single specification) {1/1 | 2/1 | 5/1 | 6/1 | 9/1 | 10/1}
P2: EtherPS lockout enable/disable setting {enable | disable}
enable: Enables EtherPS lockout
disable: Disables EtherPS lockout
Default value
P2: disable
Usage condition
If EtherPS of the specified port (line) number is not enabled, you cannot execute this
setting.
Note
None
Input example
Output item
Related
commands
set ether-ps
show ether-ps status
11-43
EtherOAM
Privilege
General
Save
Synchronize
SBY execution
Parameters
P1: Port (line) number (single specification) {1/1 | 2/1 | 5/1 | 6/1 | 9/1 | 10/1}
P2: Change timer type {wtr}
wtr: Recovery standby protection time
P3: Time (0 to 12)
* 0, and 5 to12 can be specified.
Default value
P3: 5
Usage
conditions
If EtherPS of the specified port (line) number is not enabled, you cannot execute this
setting.
If EtherPS of the specified port (line) number is set to the non-revertive mode, you
cannot execute this setting.
Note
Input example
Output item
Related
commands
set ether-ps
show ether-ps config
11-44
EtherOAM
Privilege
General
Save
Synchronize
SBY execution
change ether-ps
Changeover of EtherPS state
Changes the EtherPS state.
Input format
change ether-ps P1 P2
Parameters
P1: Port (line) number (single specification) {1/1 | 2/1 | 5/1 | 6/1 | 9/1 | 10/1}
P2: Change mode {lockout | forced | manual | exercise}
lockout: Lockout
forced: Forced change
manual: Manual change
exercise: Test request
Default value
None
Usage
conditions
If EtherPS of the specified port (line) number is not enabled, you cannot execute this
setting.
If EtherPS lockout for the specified port (line) number is enabled, you cannot execute
this setting.
Note
You may be unable to execute this command depending on the EtherPS state. Refer
to EtherPS Functions in the Instruction Manual.
Input example
Output item
Related
commands
11-45
EtherOAM
Privilege
General
Save
Synchronize
SBY execution
Parameter
P1: Port (line) number (single specification) {1/1 | 2/1 | 5/1 | 6/1 | 9/1 | 10/1}
Default value
None
Usage
conditions
If EtherPS of the specified port (line) number is not enabled, you cannot execute this
setting.
If EtherPS lockout for the specified port (line) number is enabled, you cannot execute
this setting.
Note
You may be unable to execute this command depending on the EtherPS state. Refer
to EtherPS Functions in the Instruction Manual.
Input example
Output item
Related
commands
change ether-ps
show ether-ps status
11-46
EtherOAM
Privilege
General
Synchronize
SBY execution
Parameter
P1: Port (line) number (single specification) {1/1 | 2/1 | 5/1 | 6/1 | 9/1 | 10/1}
* If P1 is omitted, the EtherPS configuration information on all EtherPS ports (lines) is
shown.
Default value
None
Usage condition
None
Note
None
Input example
11-47
EtherOAM
Output items
Related
commands
set ether-ps
set ether-ps control-vlan
set ether-ps time
11-48
EtherOAM
Privilege
General
Synchronize
SBY execution
Parameter
P1: Port (line) number (single specification) {1/1 | 2/1 | 5/1 | 6/1 | 9/1 | 10/1}
* If P1 is omitted, the EtherPS status information on all EtherPS ports (lines) is shown.
Default value
None
Usage condition
None
Note
None
Input example
11-49
EtherOAM
Output items
Related
commands
set ether-ps
set ether-ps lockout
change ether-ps
change ether-ps reset
11-50
APS
12 APS
12-1
APS
Privilege
General
Save
Synchronize
SBY execution
set aps
Setting of APS enable/disable
Sets whether to enable or disable APS and operation mode.
Input formats
Parameters
P1: Port (line) number {1/1 | 2/1 | 5/1 | 6/1 | 9/1 | 10/1}
P2: Enable/disable setting {enable | disable}
enable: Enables APS
disable: Disables APS
When enable is specified in P1
P3: Operation mode {annex-a | annex-b} (valid only when enable is set in P2)
annex-a: Annex-A(SDH) of ITU-T G.783/G.841, Annex-A(SONET) of GR-253
annex-b: Annex-B of ITU-T G.783/G.841
* If P3 is omitted, annex-b is set.
Default value
P2: disable
Usage conditions
If the ATM line module is not installed in the smaller slot number of the slots whose line
module type is NONE and which take redundant configuration, you cannot set APS.
If the line module type is not ATM155/ATMP155/TDMP155, you cannot set APS.
You cannot specify Annex-B for ports whose frame mode is set to SONET.
If the greater slot number of the specified line module has already been configured, you
cannot set APS.
If MEP has already been set for the specified line module, you cannot set APS.
If the TDMP155 line mode (SDH/SONET) is not set for the TDMP155 line module, you
cannot set APS.
Notes
Input example
Output item
12-2
APS
Related
commands
12-3
APS
Privilege
General
Save
Synchronize
SBY execution
Parameters
P1: Port (line) number {1/1 | 2/1 | 5/1 | 6/1 | 9/1 | 10/1}
P2: Enable/disable setting {enable | disable}
enable: Enables APS lockout
disable: Disables APS lockout
Default value
P2:disable
Usage conditions
Note
If APS lockout is set for only the local office or associated office, the APS status of the
local office may not match the APS status of the associated office or vice versa.
However, you can solve this mismatch by clearing the APS lockout settings.
Input example
Output item
Related
commands
set aps
change aps
change aps reset
show aps information
12-4
APS
Privilege
General
Save
Synchronize
SBY execution
Parameters
P1: Port (line) number {1/1 | 2/1 | 5/1 | 6/1 | 9/1 | 10/1}
P2: Timer {response | recover}
response: Changeover response wait time
recover: Recovery standby protection time (you cannot specify recover when APS
mode is set to Annex-A)
When response is specified in P2
P3: Time (500 to 1000 msec)
* Setting granularity: 500 (msec)
When recover is specified in P2
P3: Time (30 to 600 msec)
* Setting granularity: 30 (msec)
Default values
Usage conditions
You can set changeover response wait time and recovery standby protection time when
APS is enabled.
Note
Input examples
Output item
Related
commands
set aps
show aps information
12-5
APS
Privilege
General
Save
Synchronize
SBY execution
change aps
Changeover of APS
Changes APS.
Input formats
Parameters
P1: Port (line) number (single specification) {1/1 | 2/1 | 5/1 | 6/1 | 9/1 | 10/1}
P2: Change mode {forced | manual | lkop | exercise}
forced: Forced change
manual: Manual change
lkop: Lockout (LKOP)
exercise: Test request
When forced or manual is specified in P2
P3: Change port {master | reserve}
master: Smaller-number line module specification
reserve: Greater-number line module specification
Default value
None
Usage conditions
Notes
12-6
APS
Input examples
9/1
9/1
9/1
9/1
lkop
forced master
manual reserve
exercise
*Switch@1#
Output item
Related
commands
set aps
set aps lockout
set aps time
change aps reset
show aps information
12-7
APS
Privilege
General
Save
Synchronize
SBY execution
Parameter
P1: Port (line) number {1/1 | 2/1 | 5/1 | 6/1 | 9/1 | 10/1}
Default value
None
Usage conditions
Note
Use this command when resetting APS changeover is required after APS changeover
by the change aps command is performed.
Input example
Output item
Related
commands
set aps
set aps lockout
change aps
show aps information
12-8
APS
Privilege
General
Synchronize
SBY execution
Parameter
P1: Port (line) number {1/1 | 2/1 | 5/1, 6/1, 9/1, 10/1}
* If P1 is omitted, information of 1/1, 2/1, 5/1, 6/1, 9/1, and 10/1 is shown.
Default value
None
Usage condition
None
Note
If APS is disabled, APS Alarm information and APS Status information of the
corresponding port are not shown.
Input example
12-9
APS
Output items
Related
commands
set aps
set aps time
set aps lockout
change aps
change aps reset
12-10
ATM Control
13 ATM Control
13-1
ATM Control
Privilege
General
Save
Synchronize
SBY execution
Parameters
Default value
None
Usage condition
None
Note
None
Input example
Output item
Related
commands
Clearing of PVC
Display of PVC setting information
13-2
ATM Control
Privilege
General
Save
Synchronize
SBY execution
Parameter
Default value
None
Usage condition
None
Notes
If a PVC is cleared, other settings using the PVC are also cleared.
If the clear pvc static command with single specification of PVC identifier is executed
when no PVC is registered, an error occurs. If P1 is omitted, this command terminates
normally.
Input example
Output item
Related
commands
Registration of PVC
Display of PVC setting information
13-3
ATM Control
Privilege
General
Save
Synchronize
SBY execution
Parameters
Default value
None
Usage condition
Note
Input example
Output item
Related
commands
Registration of PVC
Clearing of PVC
Clearing of PVC name
Display of PVC setting information
13-4
ATM Control
Privilege
General
Save
Synchronize
SBY execution
Parameter
Default value
None
Usage condition
None
Notes
If the clear pvc name command with single specification of PVC identifier is executed
when no PVC is registered, an error occurs. If P1 is omitted, this command terminates
normally.
Input example
Output item
Related
commands
Registration of PVC
Clearing of PVC
Registration of PVC name
Display of PVC setting information
13-5
ATM Control
Privilege
General
Save
Synchronize
SBY execution
Parameters
Default value
P2: enable
Usage condition
Note
Input example
Output item
Related
commands
Registration of PVC
Clearing of PVC
Setting of enbloc PVC blocking/unblocking
Display of PVC setting information
13-6
ATM Control
Privilege
General
Save
Synchronize
SBY execution
Parameters
Default value
P2: enable
Usage condition
None
Notes
Input example
Output item
Related
commands
Registration of PVC
Clearing of PVC
Setting of PVC blocking/unblocking
Display of PVC setting information
13-7
ATM Control
Privilege
General
Synchronize
SBY execution
Parameters
Default value
None
Usage condition
None
Notes
None
Input example
13-8
ATM Control
Output items
Related
commands
Registration of PVC
Clearing of PVC
Registration of PVC name
Clearing of PVC name
Setting of PVC blocking/unblocking
Setting of enbloc PVC blocking/unblocking
13-9
ATM Control
Privilege
General
Save
Synchronize
SBY execution
Parameters
Default value
P2: portbase
Usage condition
None
Note
None
Input example
Output item
Related
commands
13-10
ATM Control
Privilege
General
Save
Synchronize
SBY execution
Parameters
Default value
None
Usage condition
Note
Input example
Output item
Related
commands
Registration of PVC
Clearing of PVC
Clearing of VLAN VC settings
Display of VLAN VC setting status in PVC units
Display of VLAN VC setting status in VLAN units
13-11
ATM Control
Privilege
General
Save
Synchronize
SBY execution
Parameter
Default value
None
Usage condition
None
Note
If the clear pvc-vlan table command with single specification of PVC identifier is
executed when no PVC is registered, an error occurs. If P1 is omitted, this command
terminates normally.
Input example
Output item
Related
commands
Setting of VLAN VC
Display of VLAN VC setting status in PVC units
Display of VLAN VC setting status in VLAN units
13-12
ATM Control
Privilege
General
Synchronize
SBY execution
Parameter
Default value
None
Usage condition
None
Note
None
Input example
Output items
PVC-VLAN Table
Port: Port (line) number
VPI/VCI: VPI/VCI value
VID: VLAN ID
VLAN-Name: VLAN name
13-13
ATM Control
Related
commands
13-14
ATM Control
Privilege
General
Synchronize
SBY execution
Parameter
Default value
None
Usage condition
None
Note
None
Input example
Output items
PVC-VLAN Table
VID: VLAN ID
Port: Port (line) number
VPI/VCI: VPI/VCI value
PVC-Name: PVC name
13-15
ATM Control
Related
commands
Registration of PVC
Clearing of PVC
Registration of PVC name
Setting of PVC-VLAN mode
Setting of VLAN VC
Clearing of VLAN VC settings
13-16
ATM Control
Privilege
General
Save
Synchronize
SBY execution
Parameters
Default value
P2: disable
Usage condition
None
Note
None
Input example
Output item
Related
command
13-17
ATM Control
Privilege
General
Synchronize
SBY execution
Parameter
Default value
None
Usage condition
None
Note
None
Input example
Output items
PVC-Isolate Configuration
Port: Port (line) number
Status:
enabled: PVC isolate enabled
disabled: PVC isolate disabled
Related
command
13-18
ATM Control
Privilege
General
Synchronize
SBY execution
Parameter
Default value
None
Usage condition
None
Note
None
Input example
Output items
Related
commands
VID: VLAN ID
VLAN-Name: VLAN name
13-19
ATM Control
Privilege
General
Synchronize
SBY execution
Parameters
Default value
None
Usage condition
None
Notes
If P2 (VLAN identifier) is omitted, MAC learning information of all the VLANs for the
specified port (line) number is shown. If P1 (port (line) number) is omitted, MAC
learning information of the specified VLAN for the ATM transmission path in the entire
device is shown. If P1 (port (line) number) and P2 (VLAN identifier) are omitted, MAC
learning information of all the VLANs for the ATM transmission path in the entire device
is shown.
Input examples
Output items
13-20
ATM Control
Related
commands
13-21
ATM Control
Privilege
General
Synchronize
SBY execution
Parameter
Default value
None
Usage condition
None
Notes
None
Input examples
13-22
ATM Control
Output items
Related
commands
13-23
ATM Control
Privilege
General
Synchronize
SBY execution
Parameters
Default value
None
Usage condition
None
Notes
If P2 (VLAN identifier) is omitted, the MAC learning counts of all the VLANs for the
specified port (line) number are shown. If P1 (port (line) number) is omitted, the MAC
learning count of the specified VLAN for the ATM transmission path in the entire device
is shown. If P1 and P2 are omitted, the MAC learning counts of all the VLANs for the
ATM transmission path in the entire device are shown.
13-24
ATM Control
Input examples
Output items
Related
commands
13-25
ATM Control
Privilege
General
Save
Synchronize
SBY execution
Parameter
Default value
None
Usage condition
Note
None
Input example
Output item
Related
commands
13-26
ATM Control
Privilege
General
Save
Synchronize
SBY execution
set atm-loop
Setting/clearing of ATM loop guard
Sets and clears an ATM loop guard.
Input format
set atm-loop P1 P2 P3
Parameters
Default value
P3: disable
Usage condition
You can register only the ATM loop guards mapped to the VLAN-VC.
Note
When a PVC is cleared, or when the setting of a VLAN-VC is cleared, the ATM loop
guard is automatically cleared.
Input example
Output item
Related
command
13-27
ATM Control
Privilege
General
Synchronize
SBY execution
Parameters
Default value
None
Usage condition
None
Note
Only the ATM loop guard setting statuses are shown that are mapped to the VLAN-VC.
Input example
Output items
Related
command
set atm-loop
13-28
ATM Control
Privilege
General
Synchronize
SBY execution
Parameter
Default value
None
Usage condition
None
Note
None
Input example
Output items
Related
command
clear atm-loop
VID: VLAN ID
Detect: ATM loop trap transmission state
Clearing of ATM loop detection
13-29
ATM Control
Privilege
General
Save
Synchronize
SBY execution
clear atm-loop
Clearing of ATM loop detection
Clears the ATM loop detection result.
Input format
clear atm-loop P1
Parameter
Default value
None
Usage condition
If the specified PVC has not been registered, you cannot execute this command.
Note
None
Input example
Output item
Related
command
13-30
ATM Control
Privilege
General
Save
Synchronize
SBY execution
- Specifying c-tag
set atmop mode P1 P2
- Specifying udp-ip
set atmop mode P1 P2 P3
Parameters
Default value
P2: c-tag
Usage
conditions
Note
None
Input example
Output item
Related
commands
13-31
ATM Control
Privilege
General
Save
Synchronize
SBY execution
Parameters
Default values
P10: 2142
P11: 128
P12: 46
13-32
ATM Control
Usage
conditions
If the specified PVC has not been set, you cannot execute this command.
If the settings do not match the ATM mode which has already been set, an error occurs.
If the connection types (VP connection/VC connection) of the registered PVC and the
specified PVC do not match, an error occurs.
You cannot specify the broadcast address, multicast address, local address and the
address entirely composed of "0"s.
The following IP addresses cannot be used.
0.xxx.xxx.xxx, 127.xxx.xxx.xxx, and 224.xxx.xxx.xxx to 255.xxx.xxx.xxx.
Or, network address of 192.168.128.0/24 and 192.168.129.0/24.
Only one combination of PVC and VLAN ID (*1) can be set in a card.
[combination of P1 and P7, combination of P2 and P7, combination of PVC of
inter-ATM connection setting and source and destination VLAN ID (*1)]
Multiple VLANs cannot be set to a PVC in the port.
A VLAN ID (*2) which has already been registered for TDMoP, PVC-VLAN, etc. cannot
be set.
*1: inner VLAN ID when the ATMoP mode is c-tag.
*2: outer VLAN ID when the ATMoP mode is c-tag.
Note
Input example
*Switch@1# set atmop format 3/1 0/32 5/100 00:00:00:00:00:01 outer 200 inner
3000
*Switch@1#
Output item
Related
commands
13-33
ATM Control
Privilege
General
Synchronize
SBY execution
Parameter
Default value
None
Usage condition
None
Note
None
Input example
13-34
ATM Control
Output items
ATMoP Table
Slot: Slot number
Source MAC Address: Source MAC address
* When the APS mode is enabled, two MAC addresses are displayed. One displayed
with * is used as the source MAC address.
Packet Format: Allowed packet format
Source IP Address: Source IP address
ATMoP L2-Header Table
Port: Port (line) number
VPI/VCI(ATM): VPI/VCI value
VPI/VCI(ATMoP): Conversion VPI/VCI value
Destination MAC Address: Destination MAC address
Outer VID: VLAN identifier 1
Inner VID: VLAN identifier 2
ATMoP L3-Header Table
Port: Port (line) number
VPI/VCI(ATM) : VPI/VCI value
Source UDP Port: Source port number
Destination IP Address: Destination IP address
Destination UDP Port: Destination port number
TTL: TTL value
DSCP: DSCP value
Related
commands
13-35
ATM Control
Privilege
General
Save
Synchronize
SBY execution
Parameter
Default value
None
Usage condition
None
Note
If this command is executed with single specification when no ATMoP format setting is
registered, an error occurs. If P1 is omitted, this command terminates normally.
Input example
Output item
Related
commands
13-36
ATM Control
Privilege
General
Save
Synchronize
SBY execution
Parameters
13-37
ATM Control
Default value
None
Usage
conditions
If the specified PVC has not been set, you cannot execute this command.
If the settings do not match the ATMoP mode which has already been set, an error
occurs.
If the connection types (VP connection/VC connection) of the registered PVC and the
specified PVC do not match, an error occurs.
If the PVC connection types of the source and the destination do not match, an error
occurs.
Only one combination of PVC and VLAN ID (*1) can be set in a card.
[combination of P1 and P4, combination of P1 and P9, combination of P6 and P4,
combination of P6 and P9, combination of PVC and VLAN ID (*1) in the ATMoP format
setting]
Multiple VLANs cannot be set to a PVC in the port.
A VLAN ID (*2) which has already been registered for TDMoP, PVC-VLAN, etc. cannot
be set.
The same line and VLAN ID and different PVCs for the connection source and the
connection destination cannot be set.
*1: inner VLAN ID when the ATMoP mode is c-tag.
*2: outer VLAN ID when the ATMoP mode is c-tag.
Note
Input example
*Switch@1# set pvc connection 3/1 0/32 outer 200 inner 3000 5/1 1/40 outer
400 inner 4000
*Switch@1#
Output item
Related
commands
13-38
ATM Control
Privilege
General
Synchronize
SBY execution
Parameter
Default value
None
Usage condition
None
Note
None
Input example
Output items
Related
commands
13-39
ATM Control
Privilege
General
Save
Synchronize
SBY execution
Parameter
Default value
None
Usage condition
None
Note
None
Input example
Output item
Related
commands
13-40
ATM-QoS
14 ATM-QoS
14-1
ATM-QoS
Privilege
General
Save
Synchronize
SBY execution
Parameters
Default value
P2: low
Usage condition
None
Note
If the set VPPCR or VCPCR value of the ATM shaper is less than 384 kbps, you cannot
set rate mode to high speed.
Input example
Output item
Related
command
14-2
ATM-QoS
Privilege
General
Save
Synchronize
SBY execution
Input formats
14-3
ATM-QoS
Parameters
Default value
None
Usage condition
14-4
ATM-QoS
Notes
If rate mode is set to high speed, you cannot set a value less than 384 kbps as the
VPPCR or VCPCR value of the ATM shaper.
You can set up to 128 ATM shapers in one port.
If shaper mode is VP mode, you can set up to 256 PVCs in the same ATM shaper.
If shaper mode is VC mode, you can set only one PVC in the ATM shaper.
If shaper mode is hierarchical VP mode, you can set up to 256 PVCs in the same ATM
shaper.
You cannot set different shaper mode as the same VPI value.
You cannot change the shaper mode set in the ATM shaper.
If shaper mode is set to VP mode, you can omit VPPCR value setting when changing
the traffic class or adding an PVC after setting the ATM shaper.
If shaper mode is set to VC mode, you can omit VCPCR value setting when changing
the traffic class after setting the ATM shaper.
If shaper mode is set to hierarchical VP mode, you can omit VPPCR value setting and
VCPCR value setting when changing the traffic class after setting the ATM shaper.
You can also omit VPPCR value setting when adding a PVC.
If shaper mode is VP mode, the total MCR value of the ATM shaper cannot exceed the
VPPCR value.
If shaper mode is VC mode, the MCR value of the ATM shaper cannot exceed the
VCPCR value.
If shaper mode is hierarchical VP mode, the sum of the VCPCR and MCR values of
the ATM shaper whose traffic class is CBR cannot exceed the VPPCR value.
The total effective band of the ATM shaper per port cannot exceed 150000 kbps (except
when all the traffic classes of the ATM shaper in one port are UBR).
The ATM shaper setting is automatically cleared when the PVC is cleared.
If there is a traffic of 200000Kbps or higher in the direction from the Switch module to the
ATM line module, up to PCR settings other than CBR may be unable to be output.
Input examples
Output item
Related
commands
Registration of PVC
Setting of rate mode
Display of ATM shaper
Clearing of ATM shaper
Display of effective band
14-5
ATM-QoS
Privilege
General
Synchronize
SBY execution
Parameter
Default value
None
Usage condition
None
Note
None
Input example
14-6
ATM-QoS
Output items
Related
commands
14-7
ATM-QoS
Privilege
General
Synchronize
SBY execution
Parameter
Default value
None
Usage condition
None
Note
None
Input example
14-8
ATM-QoS
3/1
3/1
3/1
3/1
3/1
3/1
3/1
3/1
3/1
9
10
11
12
13
14
15
16
17
33 vc
34 vc
--- vpvc
--- vpvc
--- vpvc
--- vpvc
--- vpvc
--- vpvc
--- vpvc
10000
10000
9000
9000
9000
9000
9000
9000
9000
----5000
----5000
5000
--5000
10000
----5000
--5000
--5000
5000
--10000
----5000
--5000
5000
5000
*Switch@1#
Output items
Related
commands
14-9
--5000
----3000
--3000
3000
3000
ATM-QoS
Privilege
General
Save
Synchronize
SBY execution
Parameter
Default value
None
Usage condition
None
Note
If VPI-value is specified or omitted, execution is confirmed after this command has been
entered.
Input example
Output item
Related
commands
14-10
ATM-QoS
Privilege
General
Save
Synchronize
SBY execution
Parameters
Default value
P2: epd
Usage condition
None
Note
None
Input example
Output item
Related
command
14-11
ATM-QoS
Privilege
General
Synchronize
SBY execution
Parameter
None
Default value
None
Usage condition
None
Note
None
Input example
Output items
Related
command
14-12
ATM-QoS
Privilege
General
Save
Synchronize
SBY execution
Parameters
Default value
None
Usage condition
Note
Input example
Output item
Related
commands
Display of CLP
Clearing of CLP
14-13
ATM-QoS
Privilege
General
Synchronize
SBY execution
Parameter
Default value
None
Usage condition
None
Note
None
Input example
Output items
Related
commands
Setting of CLP
Clearing of CLP
14-14
ATM-QoS
Privilege
General
Save
Synchronize
SBY execution
Parameter
Default value
None
Usage condition
None
Note
If VPI-value is specified or omitted, execution is confirmed after this command has been
entered.
Input example
Output item
Related
commands
Setting of CLP
Display of CLP
14-15
ATM-QoS
Privilege
General
Save
Synchronize
SBY execution
Input formats
14-16
ATM-QoS
Parameters
Default value
Usage condition
Notes
Input examples
*Switch@1#
2 inner 0
*Switch@1#
*Switch@1#
*Switch@1#
*Switch@1#
set atmop in-port cos 3/1 0/32 clp0 outer 7 inner 5 clp1 outer
set
set
set
set
atmop
atmop
atmop
atmop
in-port
in-port
in-port
in-port
cos
cos
cos
cos
Output item
14-17
ATM-QoS
Related
commands
14-18
ATM-QoS
Privilege
General
Synchronize
SBY execution
Parameter
Default value
None
Usage condition
None
Note
None
Input example
Output items
Related
commands
14-19
ATM-QoS
(Blank page)
14-20
ATM-OAM
15 ATM-OAM
15-1
ATM-OAM
Privilege
General
Save
Synchronize
SBY execution
set atm-oam
Setting of ATM-OAM operation
Sets the OAM operation of an ATM transmission path.
Input formats
- F4 level specification
set atm-oam P1 (f4) P2 P3 (disable)
- F4 to F5 transfer specification
set atm-oam P1 (f4) P2 P3 (enable) [P4]
- F5 level specification
set atm-oam P1 (f5) P2 P3
Parameters
Default value
P3: enable
P4: disable
15-2
ATM-OAM
Usage conditions
Note
Input examples
*Switch@1#
*Switch@1#
*Switch@1#
*Switch@1#
*Switch@1#
set
set
set
set
set
atm-oam
atm-oam
atm-oam
atm-oam
atm-oam
f4
f4
f4
f5
f5
3/1
3/1
3/1
3/1
3/1
0 enable
1 enable f5-generate
20 disable
0/32 enable
20/10000 disable
Output item
Related
commands
15-3
ATM-OAM
Privilege
General
Save
Synchronize
SBY execution
Input formats
- F4 level specification
set atm-oam flow P1 (f4) P2 P3 P4
- F5 level specification
set atm-oam flow P1 (f5) P2 P3 P4
Parameters
Default value
None
Usage conditions
Note
Input examples
*Switch@1#
*Switch@1#
*Switch@1#
*Switch@1#
*Switch@1#
set
set
set
set
set
atm-oam
atm-oam
atm-oam
atm-oam
atm-oam
flow
flow
flow
flow
flow
f4
f4
f5
f5
f5
15-4
3/8
3/8
3/8
3/8
3/8
0 end-end end-point
1 segment none
0/32 end-end connecting-point
1/100 segment end-point
20/10000 segment none
ATM-OAM
Output item
Related
commands
show atm-oam
show atm-oam config
show atm-oam status
15-5
ATM-OAM
Privilege
General
Synchronize
SBY execution
Parameter
Default value
None
Usage condition
None
Note
None
Input example
15-6
ATM-OAM
3/1 20/100
3/1 20/1000
3/1 255/32
3/1 255/100
disabled
disabled
enabled
enabled
--------end-point
connecting-point
connecting-point connecting-point
*Switch@1#
Output items
OAM Config(F4)
Port: Port (line) number
VPI: Virtual path number
Config: Configuration
enabled:
VP-AIS and VP-RDI detection enabled
Trap notified when VP-AIS or VP-RDI is detected
VP-RDI transferred when VP-AIS is detected
disabled:
VP-AIS and VP-RDI detection disabled
Option: Expansion setting
f5-generation: VP-RDI and VC-RDI transferred when VP-AIS is detected
none: Not specified
--- : Not set
Segment: Flow point of Segment flow
end-point: End point
connecting-point: Connecting point
End-End: Flow point of End to End flow
end-point: End point
connecting-point: Connecting point
OAM Config(F5)
Port: Port (line) number
VPI/VCI: Virtual path number/virtual channel number
Config:
enabled:
VC-AIS and VC-RDI detection enabled
Trap notified when VC-AIS or VC-RDI is detected
VC-RDI transferred when VC-AIS is detected
disabled:
VC-AIS and VC-RDI detection disabled
Segment: Flow point of Segment flow
end-point: End point
connecting-point: Connecting point
End-End: Flow point of End to End flow
end-point: End point
connecting-point: Connecting point
Related
commands
set atm-oam
show atm-oam flow
show atm-oam status
15-7
ATM-OAM
Privilege
General
Synchronize
SBY execution
Parameter
Default value
None
Usage condition
None
Note
None
Input example
15-8
ATM-OAM
3/8
3/8
3/8
3/8
3/8
3/8
3/8
3/8
3/8
3/8
3/8
3/8
3/8
3/8
3/8
3/8
0/1000
0/10000
1/32
1/100
1/1000
1/10000
20/32
20/100
20/1000
30/32
30/100
30/1000
100/32
100/100
255/32
255/100
--detect
--detect
--detect
--detect
----detect
----detect
--detect
detect
------detect
------detect
----detect
---------
--detect
detect ------detect ----detect
detect ------detect ----detect
----detect ----detect
----detect ------detect ---
---------------------------------
Switch@1#
Output items
15-9
--gen
--gen
--gen
--gen
----gen
----gen
--gen
---------------------------------
--gen
--gen
--gen
--gen
----gen
----gen
--gen
ATM-OAM
Related
commands
15-10
ATM-IMA
16 ATM-IMA
16-1
ATM-IMA
Privilege
General
Save
Synchronize
SBY execution
Parameters
Default values
P4: 1
P5: 128
P6: 25 (msec)
P7: The port (line) with the smallest number in the port (line) numbers specified in P2
Usage condition
None
Notes
Input examples
Output item
16-2
ATM-IMA
Related
commands
16-3
ATM-IMA
Privilege
General
Synchronize
SBY execution
Parameter
Default value
None
Usage condition
None
Note
None
Input example
Output items
Related
commands
16-4
ATM-IMA
Privilege
General
Synchronize
SBY execution
Parameter
Default value
None
Usage condition
None
Note
None
16-5
ATM-IMA
Input examples
When IMA group index is omitted or multiple IMAA group indexes are specified
Switch@1# show ima group status
IMA Group Status Table
======================
Index ID GSM-State(NE)
GSM-State(FE)
Failure-State
----------------------------------------------------------------------------1 1 operational
operational
no-failure
3 2 ------7 1 startup
--no-failure
9 2 startup
--no-failure
48 0 insufficient-links insufficient-links insufficient-links-ne
Switch@1#
When single IMA group index is specified.
Switch@1# show ima group status 2
IMA Group Status Table
======================
Index ID GSM-State(NE)
GSM-State(FE)
Failure-State
----------------------------------------------------------------------------2 1 operational
operational
no-failure
IMA Link Status Table
=====================
Port LID TxState(NE) RxState(NE) TxState(FE) RxState(FE) Failure-State
--------------------------------------------------------------------------10/2
1 misconnect misconnect
misconnect misconnect misconnect
10/4
3 active
active
active
active
no-failure
10/6
5 active
active
active
active
no-failure
Switch@1#
16-6
ATM-IMA
Output items
16-7
ATM-IMA
Failure-State:
---: Line module uninstalled
no-failure: No failure information
failure: Failure (others)
LIF-failure: Failure (LIF)
LODS-failure: Failure (LODS)
misconnect: Failure (misconnect)
blocked: Failure (blocked status)
fault: Failure (user individual)
tx-unusable: Waiting for transition to next Tx status
rx-unusable: Waiting for transition to next Rx status
Related
commands
16-8
ATM-IMA
Privilege
General
Save
Synchronize
SBY execution
Parameter
Default value
None
Usage condition
None
Note
None
Input example
Output item
Related
commands
16-9
ATM-IMA
Privilege
General
Save
Synchronize
SBY execution
Parameters
Default value
P2: ctc
Usage condition
None
Note
If a line module to which an IMA group has already been set is specified, the IMA group
automatically performs the setting again. Communication is suspended until the IMA
group re-setting is completed (i.e., operational state).
Input example
Output item
Related
commands
16-10
ATM-IMA
Privilege
General
Synchronize
SBY execution
Parameter
Default value
None
Usage condition
None
Note
None
Input example
Output items
Related
command
16-11
ATM-IMA
Privilege
General
Save
Synchronize
SBY execution
loopback ima
Starting and result display of IMA loopback test
Starts an IMA loopback test and shows the result.
Input format
loopback ima P1 P2
Parameters
Default value
None
Usage condition
An IMA group must be set in advance for the port (line) to which the loopback test is
performed.
Note
Input example
16-12
ATM-IMA
Output items
Related
command
16-13
ATM-IMA
(Blank page)
16-14
TDM-Path
17 TDM-Path
17-1
TDM-Path
Privilege
General
Save
Synchronize
SBY execution
Parameters
Default value
None
17-2
TDM-Path
Usage
conditions
tdm must be set in the TDMP line mode setting or the TDMP155 line mode setting in
advance.
Time slot numbers, group numbers, or group names already set to a group within the
same port (line) cannot be used.
When the frame type is set to E1 or SDH mode, the frame format must be set to
unframed to use time slot number 0.
Note
None
Input examples
*Switch@1#
*Switch@1#
*Switch@1#
*Switch@1#
*Switch@1#
set
set
set
set
set
tdm
tdm
tdm
tdm
tdm
group
group
group
group
group
1/1 e1 1 1
2/1 e1 1 0-31
12/8 t1 24 1-24
3/1 sdh 1/1/1 1 1
4/1 sonet 1/7/4 SONET_1 1-24
Output item
Related
commands
17-3
TDM-Path
Privilege
General
Synchronize
SBY execution
Parameters
Default value
None
Usage condition
None
Note
17-4
TDM-Path
Input examples
Output items
Related
commands
17-5
TDM-Path
Privilege
General
Save
Synchronize
SBY execution
Parameters
Default value
None
Usage
conditions
tdm must be set in the TDMP line mode setting or the TDMP155 line mode setting in
advance.
If a group to which a TDM path is set is specified, an error occurs.
Note
17-6
TDM-Path
Input examples
Output item
Related
commands
17-7
TDM-Path
Privilege
General
Save
Synchronize
SBY execution
Parameters
Default value
None
Usage condition
The TDMP line mode or the TDMP155 line mode must be set in advance.
Note
If a command that changes the frame type is entered in the TDMP line mode setting or
the TDMP155 line mode setting, the TDM group name of the line module is cleared.
Input examples
Output item
17-8
TDM-Path
Related
commands
17-9
TDM-Path
Privilege
General
Synchronize
SBY execution
Parameters
Default value
None
Usage condition
None
Note
None
17-10
TDM-Path
Input example
*Switch@1#
*Switch@1# show tdm group-name
TDM Group Name Table
====================
Logical
Port Port
Group Name
-----------------------------------------------------1/8
--1 CX2600_220_MBH_GROUP_NAME_AAAAAA
7/1
3/7/3
32 CX2600_220_SDH_GROUP_NAME_BBBBBB
12/1
3/7/4
24 CX2600_220_SONET_GROUP_NAME_CCCC
*Switch@1#
Output items
Related
commands
17-11
TDM-Path
Privilege
General
Save
Synchronize
SBY execution
Parameters
Default value
None
Usage
conditions
The TDMP line mode or the TDMP155 line mode must be set in advance.
When a group name is specified, an error occurs when the group name does not exist.
Note
None
Input examples
Output item
17-12
TDM-Path
Related
commands
17-13
TDM-Path
Privilege
General
Save
Synchronize
SBY execution
Parameters
Default value
None
17-14
TDM-Path
Usage
conditions
tdm must be set in the TDMP line mode setting or the TDMP155 line mode setting in
advance.
If a group number or group name to which a TDM group is not set, an error occurs.
If a group to which a TDM path has already been set is specified, an error occurs.
If a TDM path is set within the same port (line) or the same logical port, an error occurs.
If groups with different frame type each other are specified, an error occurs.
A path can be set only to groups with the same number of time slots.
Note
Input example
Output item
Related
commands
17-15
TDM-Path
Privilege
General
Synchronize
SBY execution
Parameters
Default value
None
Usage condition
None
Notes
Information is displayed based on the small port (line) number with TDM path setting.
side-A and side-B displayed in the side column indicate the pair of the TDM path setting.
Input examples
17-16
TDM-Path
Output items
Related
commands
17-17
TDM-Path
Privilege
General
Save
Synchronize
SBY execution
Parameters
Input format
Parameters
Default value
None
Usage condition
tdm must be set in the TDMP line mode setting or the TDMP155 line mode setting in
advance.
Note
To clear a TDM path setting, specify one from the port (line) number, the group number,
or the group number used for the TDM path setting. (Specifying the port (line) number,
the group number, or the group name clears the TDM path setting.)
If P3 is omitted, execution is verified after the command entry.
17-18
TDM-Path
Input examples
Output item
Related
commands
17-19
TDM-Path
(Blank page)
17-20
18-1
General
Save
Synchronize
SBY execution
Parameters
Default value
Usage
conditions
Note
None
18-2
Output item
Related
commands
18-3
General
Save
Synchronize
SBY execution
Parameter
Default value
None
Usage condition
Note
None
Input example
Output item
Related
commands
18-4
General
Save
Synchronize
SBY execution
Parameters
18-5
None
Usage
conditions
Notes
Input examples
*Switch@1#
*Switch@1#
*Switch@1#
*Switch@1#
*Switch@1#
set
set
set
set
set
tdmop
tdmop
tdmop
tdmop
tdmop
group
group
group
group
group
1/1 e1 1 1-32
12/1 t1 1 1-24
12/7 t1 1 all
2/1 sdh 1/2/1 1 all
6/1 sonet 1/1/1 SONET_1 all
Output item
Related
commands
18-6
General
Synchronize
SBY execution
Parameter
Default value
None
Usage condition
None
Note
None
18-7
Output items
Related
commands
18-8
General
Save
Synchronize
SBY execution
Parameters
Default value
None
Usage
conditions
18-9
If a group to which variation tolerance has been set is cleared, the variation tolerance
returns to the default value.
If a group to which adaptive clock has been set is cleared, adaptive clock setting for the
group is also cleared automatically.
If P3 and P4 are omitted, execution is verified after the command entry.
Input examples
Output item
Related
commands
18-10
General
Save
Synchronize
SBY execution
Parameters
18-11
P10: 5
Usage
conditions
Note
None
Input examples
*Switch@1#
*Switch@1#
*Switch@1#
*Switch@1#
set
set
4/1
set
tdmop
tdmop
1/1/1
tdmop
Output item
Related
commands
18-12
General
Synchronize
SBY execution
Parameters
Default value
None
Usage condition
None
Note
None
Input example
18-13
Related
commands
18-14
General
Save
Synchronize
SBY execution
Parameters
Default value
None
Usage condition
Notes
Input examples
Output item
Related
commands
18-15
18-16
General
Save
Synchronize
SBY execution
Parameters
Default value
P4: 4ms
Usage
conditions
Only a group number or a group name to which a TDMoP group is set can be specified.
If variation tolerance is set to a group to which the following commands have been
executed, an error occurs.
set tdmop format
set tdmop connection
* However, setting is available even under the above conditions when
blocking/unblocking setting of the TDMoP is blocked.
Notes
If a TDMoP group is set, the variation tolerance is set back to the default value.
If a TDMoP group is cleared, the variation tolerance is set back to the default value.
To return to the default value, enter the command specifying 4ms in P4.
Input example
18-17
Related
commands
18-18
General
Synchronize
SBY execution
Parameters
Default value
None
Usage condition
None
Note
None
Input examples
18-19
Related
commands
18-20
General
Synchronize
SBY execution
Parameters
Default value
None
Usage condition
None
Note
None
18-21
Output items
Related
commands
18-22
General
Save
Synchronize
SBY execution
18-23
Default values
Usage
conditions
A TDMoP format can be set only to a group number or a group name to which a TDMoP
group is set.
If a VLAN ID which is set for ATMoP or the like is specified, an error occurs.
You cannot set 0.xxx.xxx.xxx/127.xxx.xxx.xxx or 224.xxx.xxx.xxx to 255.xxx.xxx.xxx as
the IP address. (xxx is any numeric character.)
You cannot set network address of 192.168.128.0/24 or 192.168.129.0/24.
If you specify the same destination IP address as the source IP address, an error
occurs.
The ECID must be unique in an identical line module.
If a group to which any of the following is set is specified, an error occurs.
set tdmop format
set tdmop connection
18-24
None
Input examples
Output item
Related
commands
18-25
General
Synchronize
SBY execution
Parameters
Default value
None
Usage condition
None
Note
When APS is enabled, the source MAC addresses are displayed in two lines. The
character "*" is attached to the display of the enabled one.
18-26
Output items
18-27
18-28
General
Save
Synchronize
SBY execution
Parameters
Default value
None
Usage condition
Notes
Input examples
Output item
18-29
18-30
General
Save
Synchronize
SBY execution
Parameters
Default value
P4: enable
Usage condition
If a group to which neither a TDMoP format nor a TDMoP connection is set is specified,
an error occurs.
Note
Input examples
Output item
18-31
18-32
General
Save
Synchronize
SBY execution
Parameters
Default value
P4: wide
Usage
conditions
Notes
Input examples
18-33
Related
commands
18-34
General
Synchronize
SBY execution
Parameter
None
Default value
None
Usage condition
None
Note
None
Input example
Output items
Related
commands
18-35
General
Save
Synchronize
SBY execution
Parameters
Default value
None
Usage
conditions
Note
None
Input example
Output item
18-36
18-37
(Blank page)
18-38
Clock Control
19 Clock Control
19-1
Clock Control
Privilege
General
Save
Synchronize
SBY execution
Parameter
Default value
P1: none
Usage
conditions
Execute change of external clock mode after a clear indication (specifying none).
External clock mode cannot be cleared while external clock is set in the priority. Set
external clock mode again after clearing external clock from the priority settings.
Note
None
Input examples
Output item
19-2
Clock Control
Related
commands
19-3
Clock Control
Privilege
General
Save
Synchronize
SBY execution
Input formats
Parameters
Default value
None
19-4
Clock Control
Usage
conditions
Note
None
Input examples
*Switch@1#
*Switch@1#
*Switch@1#
*Switch@1#
*Switch@1#
*Switch@1#
set
set
set
set
set
reference-clock
reference-clock
reference-clock
reference-clock
reference-clock
priority
priority
priority
priority
priority
1
2
4
3
1
external 1
external 2
port tdmp 12/8
adaptive tdmp 3
none
Output item
Related
commands
19-5
Clock Control
Privilege
General
Save
Synchronize
SBY execution
Parameter
Default value
P1: non-revertive
Usage condition
None
Note
None
Input examples
Output item
Related
commands
19-6
Clock Control
Privilege
General
Synchronize
SBY execution
Parameter
None
Default value
None
Usage condition
None
Note
None
Input example
19-7
Clock Control
Output items
Related
commands
19-8
Clock Control
Privilege
General
Save
Synchronize
SBY execution
reset reference-clock
Resetting of reference clock
Selectively resets the reference clock.
Input format
reset reference-clock
Parameter
None
Default value
None
Usage condition
None
Note
When a clock is supplied to the source clock with higher priority over the reference clock
that is currently selected, switch the reference clock.
Input example
Output item
Related
commands
19-9
Clock Control
Privilege
General
Save
Synchronize
SBY execution
change external-clock
Change of external clock
Changes external clock.
Input format
change external-clock
Parameter
None
Default value
None
Usage
conditions
Note
None
Input example
Output item
Related
commands
19-10
Network Management
20 Network
Management
20-1
Network Management
Privilege
General
Save
Synchronize
SBY execution
set snmp
Setting of SNMP enable/disable
Sets SNMP security access.
Input format
set snmp P1
Parameter
Default value
P1: disable
Usage condition
None
Note
None
Input example
Output item
Related
commands
20-2
Network Management
Privilege
General
Save
Synchronize
SBY execution
Parameters
Default value
None
Usage conditions
When using the same community, you cannot set a different access authority.
Notes
Input example
Output item
Related
commands
20-3
Network Management
Privilege
General
Save
Synchronize
SBY execution
Parameters
Default value
None
Usage conditions
Notes
Set a community name and memo with ASCII characters other than ["], [?], and [control
character].
When using [space], enclose the entire character string in double quotation marks.
Input example
Output item
Related
commands
20-4
Network Management
Privilege
General
Save
Synchronize
SBY execution
Parameter
Default value
None
Usage condition
None
Note
None
Input example
Output item
Related
commands
set snmp
set snmp manager
show snmp
20-5
Network Management
Privilege
General
Save
Synchronize
SBY execution
Parameter
Default value
None
Usage condition
None
Note
None
Input example
Output item
Related
commands
set snmp
set snmp trap-manager
show snmp
20-6
Network Management
Privilege
General
Save
Synchronize
SBY execution
Parameter
Default value
P1: enable
Usage condition
None
Note
None
Input example
Output item
Related
commands
20-7
Network Management
Privilege
General
Synchronize
SBY execution
show snmp
Display of SNMP setting information
Shows SNMP setting information.
Input format
show snmp
Parameter
None
Default value
None
Usage condition
None
Note
None
Input example
20-8
Network Management
Trap Mode
Note
: v1
:
Output items
Related
commands
set snmp
set snmp manager
set snmp trap-manager
set snmp authen-trap
how snmp
clear snmp trap-manager
clear snmp manager
20-9
Network Management
Privilege
General
Save
Synchronize
SBY execution
Parameters
Default value
None
Usage conditions
Note
None
Input example
Output item
Related
commands
20-10
Network Management
Privilege
General
Synchronize
SBY execution
Parameter
Default value
None
Usage condition
None
Note
None
Input example
Output items
Related
commands
20-11
Network Management
Privilege
General
Save
Synchronize
SBY execution
Parameter
Default value
None
Usage condition
None
Note
None
Input example
Output item
Related
commands
20-12
Network Management
Privilege
General
Synchronize
SBY execution
show session
Display of session
Shows terminal line information.
Input format
show session
Parameter
None
Default value
None
Usage condition
None
Note
None
Input example
Output items
Related
command
clear session
Clearing of session
20-13
Network Management
Privilege
General
Save
Synchronize
SBY execution
clear session
Clearing of session
Clears a telnet session.
Input format
clear session P1
Parameter
Default value
None
Usage condition
None
Note
None
Input example
Output item
Related
command
show session
Display of session
20-14
Network Management
Privilege
General
Save
Synchronize
SBY execution
Parameter
Default value
P1: disable
Usage condition
None
Note
None
Input example
Output item
Related
commands
20-15
Network Management
Privilege
General
Save
Synchronize
SBY execution
Parameters
Default value
None
Usage conditions
Note
None
Input example
Output item
Related
commands
20-16
Network Management
Privilege
General
Synchronize
SBY execution
Parameter
None
Default value
None
Usage condition
None
Note
None
Input example
Output items
Related
commands
20-17
Network Management
Privilege
General
Save
Synchronize
SBY execution
Parameter
Default value
None
Usage condition
None
Note
None
Input example
Output item
Related
commands
20-18
Network Management
Privilege
General
Save
Synchronize
SBY execution
Parameters
P1: Group
For the group parameter, refer to Mapping of syslog Functions of Method of
Operating Maintenance and Management Functions in the Instruction Manual.
P2: syslog level
For the syslog level parameter, refer to Mapping of syslog Functions of Method of
Operating Maintenance and Management Functions in the Instruction Manual.
Default value
For the default values, refer to Mapping of syslog Functions of Method of Operating
Maintenance and Management Functions in the Instruction Manual.
Usage condition
None
Note
None
Input example
Output item
Related
commands
20-19
Network Management
Privilege
General
Synchronize
SBY execution
Parameter
None
Default value
None
Usage condition
None
Note
None
Input example
Output items
For the output items, refer to Mapping of syslog Functions of Method of Operating
Maintenance and Management Functions in the Instruction Manual.
Related
commands
20-20
Network Management
Privilege
General
Save
Synchronize
SBY execution
Parameter
P1: Group
For the group parameter, refer to Mapping of syslog Functions of Method of
Operating Maintenance and Management Functions in the Instruction Manual.
Default value
For the default value, refer to Mapping of syslog Functions of Method of Operating
Maintenance and Management Functions in the Instruction Manual.
Usage condition
None
Note
None
Input example
Output item
Related
commands
20-21
Network Management
Privilege
General
Synchronize
SBY execution
Parameters
Default value
None
Usage condition
Note
None
20-22
Network Management
Input example
Output items
Related
commands
20-23
Network Management
Privilege
General
Save
Synchronize
SBY execution
Parameter
None
Default value
None
Usage condition
None
Note
None
Input example
Output item
Related
commands
20-24
Network Management
Privilege
General
Save
Synchronize
SBY execution
Parameter
Default value
P1: 0 (hour)
Usage condition
None
Note
None
Input example
Output item
Related
commands
20-25
Network Management
Privilege
General
Save
Synchronize
SBY execution
Parameters
Default value
None
Usage conditions
Note
None
Input example
Output item
Related
commands
20-26
Network Management
Privilege
General
Synchronize
SBY execution
show ntp
Display of NTP server setting information
Shows NTP server setting information.
Input format
show ntp
Parameter
None
Default value
None
Usage condition
None
Note
None
Input example
Output items
Related
commands
20-27
Network Management
Privilege
General
Save
Synchronize
SBY execution
Parameter
Default value
None
Usage condition
None
Note
None
Input example
Output item
Related
commands
20-28
Network Test
21 Network Test
21-1
Network Test
Privilege
General
Save
Synchronize
SBY execution
set mc management
Setting of M/C management function basics
Sets terminal M/C management function basics. Enabling this setting allows you to perform a loopback
test and collect terminal M/C information.
Input formats
Parameters
P1: Port (line) number (1/1 to 4/8) (Multiple values can be specified.)
P2: Enable/disable setting {enable | disable}
enable: Enables setting M/C management function basics
disable: Disables setting M/C management function basics
When enable is specified in P2
P3: UTP mode setting {utp}
utp: UTP mode
Default value
P2* enable
Usage condition
Note
Note
Input example
Output item
Related
command
show mc information
21-2
Network Test
Privilege
General
Save
Synchronize
SBY execution
loopback mc
Starting of M/C loopback test
Starts the media converter (M/C) loopback test when the 100BASE-FX line module is used. This loopback
test requires that enable be selected in the set mc management command in advance.
Input format
Parameters
P1: Port (line) number (1/1 to 4/8) (Multiple values can be specified.)
P2: Test count (count 1 to 1000)
* If P2 is omitted, count 1 is set.
P3: Frame size (frame {64 | 1518}) (bytes)
64 : 64 bytes
1518: 1518 bytes
* If P3 is omitted, frame 64 is set.
P4: Response wait time (wait 610 to 2000) (msec)
* If P4 is omitted, wait 610 is set.
Default value
None
Usage conditions
Since frames cannot be transferred between this device and the user during the
loopback test, do not conduct this test on a line in use. Depending on the M/C to be
used, the UTP side may link down during the loopback test. In this case, the user side
detects network disconnection.
Note
You can set response wait time within the range from 610 to 2000 (msec) in units of 10
(msec). For how to look at the test result, refer to the Instruction Manual.
Input example
*Switch@1#
result 9/3
result 9/3
result 9/3
result 9/3
21-3
Network Test
Output items
Related
command
set mc management
21-4
Network Test
Privilege
General
Save
Synchronize
SBY execution
update mc information
Prompting of M/C to send M/C status notification
Prompts the M/C to send an M/C status notification.
Input format
update mc information P1
Parameter
Default value
None
Usage condition
You can enter this command when the FX8/FX8-PV line module is inserted into the
specified slot or FX8 is specified as the line module type.
Notes
This command prompts the M/C to send an M/C status notification when the M/C may
not autonomously send it.
Originally, the M/C status is automatically collected when link-up is established.
Usually, you need not use this command because the M/C autonomously sends the M/C
status notification when the M/C status changes.
If a failure may have occurred, see the loopback mc command separately.
Input example
Output item
Related
commands
loopback mc
show mc information
21-5
Network Test
Privilege
General
Synchronize
SBY execution
show mc information
Display of M/C information
Shows terminal M/C information.
Input format
Parameter
[P1]: Line module number (single specification) or port (line) number (Multiple values
can be specified.)
Line module number (single specification) 1 to 4
Port (line) number (1/1 to 4/8) (Multiple values can be specified.)
* If P1 is omitted, terminal M/C information for all line modules is shown.
Default value
None
Usage condition
None
Note
Some terminal M/C information is shown only when a port (line) number is specified.
Input examples
21-6
Network Test
1/7 enabled
1/8 enabled
utp
none
*Switch@1#
Output items
21-7
Network Test
Related
command
set mc management
21-8
Network Test
Privilege
General
Save
Synchronize
SBY execution
loopback atm
Starting of ATM loopback test
Starts the ATM transmission path loopback test.
Input formats
- Specifying F4 level
loopback atm P1(f4) P2 [P3] [P4] [P5] [P6] [P7] [P8]
- Specifying F5 level
loopback atm P1(f5) P2 [P3] [P4] [P5] [P6] [P7] [P8]
Parameters
21-9
Network Test
Default values
P3: end
P4: 0xffffffffffffffffffffffffffffffff
P5: enable
P6: 1
P7: 5
P8: outside
Usage conditions
When f4 is specified in P1, this function cannot be executed if the VP connection or the
PVC that includes the targeted VPI has not been registered.
When f5 is specified in P1, this function cannot be executed if the targeted PVC has not
been registered.
You cannot also execute this function simultaneously on multiple ports.
When inside is specified in P8, this function cannot be executed if OAM flow point of the
targeted VPI or PVC is set to end-point.
You cannot execute multiple loopback test (specifying 0x0 for the location ID).
* Refer to the "set atm-oam flow" command for OAM flow point setting.
Note
Input examples
*Switch@1#
result 3/1
result 3/1
result 3/1
21-10
Network Test
Output items
Related
commands
21-11
Network Test
Privilege
General
Save
Synchronize
SBY execution
Parameter
Default value
P1: 0x00000000000000000000000000000001
Usage condition
Note
None
Input example
Output item
Related
commands
loopback atm
set loopback atm source-id
21-12
Network Test
Privilege
General
Synchronize
SBY execution
Parameter
None
Default value
None
Usage condition
None
Note
None
Input example
Output item
Related
commands
loopback atm
set loopback atm source-id
21-13
Network Test
Privilege
General
Save
Synchronize
SBY execution
Parameter
Default value
P1: disable
Usage condition
None
Notes
Timeout for each PVC is 5 seconds and the monitoring period for all PVCs is 5 minutes.
When loopback monitoring is enabled, monitoring statistical information is cleared.
Input example
Output item
Related
commands
21-14
Network Test
Privilege
General
Synchronize
SBY execution
Parameter
Default value
None
Usage condition
None
Note
None
Input example
21-15
Network Test
=========================
Keepalive-Mode : enabled
ATM Loopback Cell F4 Config Table
=================================
No entry in the table.
ATM Loopback Cell F5 Config Table
=================================
Port VPI/VCI Section Direction Success Threshold Fail Threshold
-------------------------------------------------------------------1/1 100/100 segment outside
1
1
ATM Loopback Cell F5 Location-ID
================================
Port VPI/VCI Location-ID
------------------------------------------------1/1 100/100 0x00000000000000000000000000000001
*Switch@1#
Output items
21-16
Network Test
Related
commands
21-17
Network Test
Privilege
General
Save
Synchronize
SBY execution
- Specifying F4 level
set loopback atm keepalive P1 (f4) P2 [P3] [P4] [P5] [P6]
- Specifying F5 level
set loopback atm keepalive P1 (f5) P2 [P3] [P4] [P5] [P6]
Parameters
Default values
P3: end
P4: 0xffffffffffffffffffffffffffffffff
P5: 1
P6: 1
21-18
Network Test
Usage conditions
When f4 is specified in P1, this function cannot be executed if the VP connection or the
PVC that includes the targeted VPI has not been registered.
When f5 is specified in P1, this function cannot be executed if the targeted PVC has not
been registered.
You cannot simultaneously set F4 monitoring and F5 monitoring specifying an identical
VP.
If the loopback monitoring configuration is changed, monitoring statistical information
for the PVC that performs loopback monitoring is cleared.
When inside is specified in P7, this function cannot be executed if OAM flow point of the
targeted VPI or PVC is set to end-point.
You cannot execute multiple loopback test (specifying 0x0 for the location ID).
* Refer to the "set atm-oam flow" command for OAM flow point setting.
Notes
If the PVC is cleared, the monitoring settings of this function for the PVC are also
cleared.
If all the PVCs that include a certain VPI is cleared, the monitoring settings of this
function for the VP are also cleared.
The monitoring settings changed during loopback monitoring are reflected in the next
period.
Function that allows to specify inside in P7 will be supported in the future.
Input examples
Output item
Related
commands
21-19
Network Test
Privilege
General
Synchronize
SBY execution
Default value
None
Usage condition
None
Note
None
Input example
21-20
Network Test
Output items
Related
commands
21-21
Network Test
Privilege
General
Save
Synchronize
SBY execution
- Specifying F4 level
clear loopback atm keepalive P1(f4) P2
- Specifying F5 level
clear loopback atm keepalive P1(f5) P2
- Specifying line number
clear loopback atm keepalive P1(line number)
Parameters
Default value
None
Usage condition
None
Note
The monitoring settings cleared during loopback monitoring are not reflected right after
execution of the command. Reflection requires up to 5 minutes because loopback
monitoring is executed in 5 minute periods.
Input examples
Output item
21-22
Network Test
Related
commands
21-23
Network Test
(Blank page)
21-24
Monitors
22 Monitors
22-1
Monitors
Privilege
General
Synchronize
SBY execution
- Realtime showing
show counter port P1 (real) P2 (up to 24 port (line) numbers)
- Detailed showing
show counter port P1 (detail) P2 (single port (line) number)
Parameters
Default value
None
Usage condition
Notes
If the specified port (line) is in line module duplex operation, counter information of the
greater number port is also shown.
In realtime showing, you can simultaneously show up to 24 lines. However, only 20
lines will be displayed in the case of specification that exceeds the maximum number
of lines.
Pressing [Ctrl]+[C] in realtime showing enables you to end port counter showing.
If the counter value exceeds either of 32 bits or 64 bits (*), the value will be returned to
zero and then incremented from zero again.
* 32 bits = 4294967295, 64 bits = 18446744073709551615
The counter value may be unable to be collected during UGSW module system
switching.
If discarding is caused by an FCS error or a frame size violation, even the output port
may increment the discard counter value.
If a frame is interrupted by a transfer block of the port isolate function, the input port
may increment the discard counter value.
When it receives a frame of large size (FE: frames of 8 kilobytes or more,
GbE/GbE-MUX: frames of 16 kilobytes or more), the line module may shorten the
frame size and increment the error counter value (e.g., RxJabbers).
Input examples
22-2
Monitors
9/1 down
| 12/1 down
Output items
TxOctets Last clearing time of port counter: Elapsed time of counter collection
(Realtime showing)
The elapsed time of counter collection for the entire device is shown in the
hour:minute:second format.
When the elapsed time exceeds 24 hours, over 24 hour is shown.
If the port counter is cleared per port or the line module is reset or if the line module
is inserted, unknown hour is shown.
Clearing all the port counters also clears the elapsed time of counter collection for
the device at the same time.
22-3
Monitors
(Detailed showing)
The elapsed time of counter collection for the specified port is shown in the
hour:minute:second format.
When the elapsed time exceeds 24 hours, over 24 hour is shown.
Clearing the port counter also clears the elapsed time of counter collection for the
port at the same time.
RxOctets:
RxPkts:
RxDropEvents:
RxErrors:
RxUndersizePkts:
Related
commands
22-4
Monitors
Privilege
General
Save
Synchronize
SBY execution
Parameter
Default value
None
Usage condition
Note
Input example
Output item
Related
commands
22-5
Monitors
Privilege
General
Synchronize
SBY execution
Parameter
Default value
None
Usage condition
Notes
If the specified port (line) is in line module duplex operation, counter information of the
greater number port is also shown.
If the active slot side increments RxDisOutQoS Pkts and L2SW Discard Counter items
during line module duplex operation, counter items for lines in the both systems will be
incremented.
The counter value may be unable to be collected during UGSW module system
switching.
If discarding is caused by an FCS error or a frame size violation, even the output port
may increment the discard counter value.
If a frame is interrupted by a transfer block of the port isolate function, the input port may
increment the discard counter value.
GbE-MUX collects RxDisOutQoS Pkts and L2SW Discard Counter items in line
module units, so all the ports increment the same counter value without reference to link
up and down.
Input example
22-6
Monitors
RxMACLimitPkts :
RxFairnessPkts :
0 |
0 |
Output items
Related
commands
22-7
Monitors
Privilege
General
Synchronize
SBY execution
Parameters
Default value
None
Usage condition
22-8
Monitors
Notes
Using VLAN counter display requires that counter information collection conditions in
VLAN units be registered in advance.
If the specified port is in line module duplex operation when the counter collection cycle
is short and the showing type is detail or when the counter collection cycle is long,
counter information of the greater number port is also shown.
If the specified port is in line module duplex operation when the counter collection cycle
is short and the showing type is real time detail, information of the active port side
counter is also shown.
For detailed showing, specifying priority in P5 enables VLAN counter information to be
shown in priority units.
For realtime showing or detailed realtime showing, pressing [Ctrl]+[C] enables you to
end counter information showing.
If the counter value exceeds either of 32 bits or 64 bits (*), the value will be returned to
zero and then incremented from zero again.
If the active slot side increments RxDisOutQoS Octs and RxDisOutQoSPkts counter
items during line module duplex operation, counter items for lines in the both systems
will be incremented.
VLAN counter values may be unable to be collected during UGSW module system
switching or VLAN settings change.
When VLAN tag swapping is set, the VLAN counter is incremented based on the
swapping source VLAN-ID.
The CoS priority mapping setup port shows post-mapping priority values.
The portbase VLAN setup port increments the VLAN counter when the priority value is
0. (However, the CoS priority mapping setup port shows post-mapping priority values.)
If no priority is mapped to the specified class, class information and target counter items
are shown by hyphens ---.
There may be a case that some of counters cannot be displayed when the specification
exceeds the maximum display number of VIDs or when a slot in line module duplex
operation is specified. If there is any counter not displayed, a sentence will be
displayed to indicate it.
Input examples
22-9
Monitors
RxBcastOcts
:
RxDisInQoSOcts :
RxDisOutQoSOcts :
RxFilterOcts
:
RxMACLimitOcts :
RxPkts
:
RxUcastPkts
:
RxMcastPkts
:
RxBcastPkts
:
RxDisInQoSPkts :
RxDisOutQoSPkts :
RxFilterPkts
:
RxMACLimitPkts :
RxFairnessPkts :
0 | TxBcastOcts
:
0 |
0 | TxDisOutQoSOcts :
0 | TxFilterOcts
:
0 |
0 | TxPkts
:
0 | TxUcastPkts
:
0 | TxMcastPkts
:
0 | TxBcastPkts
:
0 |
0 | TxDisOutQoSPkts :
0 | TxFilterPkts
:
0 |
0 |
0
0
0
0
0
0
0
0
0
22-10
Monitors
Output items
22-11
Monitors
[Class showing]
Line(In-Maximum):
Line(In-Fairness):
Line(Out-Maximum):
Switch(Out-Fairness):
Related
commands
22-12
Monitors
Privilege
General
Save
Synchronize
SBY execution
Parameters
Default value
None
Usage condition
Notes
Input example
Output item
Related
commands
22-13
Monitors
Privilege
General
Save
Synchronize
SBY execution
Parameters
Default value
None
Usage condition
Notes
If the specified port (line) is in line module duplex operation, VLAN counter collection
conditions for the greater number port are also registered.
Each of the maximum numbers of VLAN counter information collection conditions that
can be registered is as follows:
- Maximum number of VLAN counter information collection conditions that can be
registered when the counter collection cycle is short: 16
- Maximum number of VLAN counter information collection conditions that can be
registered when the counter collection cycle is long: 256
- Maximum number of VLAN counter information collection conditions that can be
registered per slot: 64
*
(For the GbE-MUX line module, the maximum number of VLAN counter information
collection conditions that can be registered per slot is 128.)
- Maximum number of VLAN counter information collection conditions that can be
registered per port: 16
*
* This maximum number is the total of the maximum number of VLAN counter
information collection conditions that can be registered when the counter collection
cycle is short and that when the counter collection cycle is long. The settings of the
same port and VLAN when the counter collection cycle is short and those when the
counter collection cycle is long are counted as 1.
Input example
Output item
Related
commands
22-14
Monitors
22-15
Monitors
Privilege
General
Synchronize
SBY execution
Parameters
Default value
None
Usage condition
Notes
The number of counter collection condition information registered in VLAN units shown
in Entry Count does not include information of the greater number port.
Input example
Output items
22-16
Monitors
Related
commands
22-17
Monitors
Privilege
General
Save
Synchronize
SBY execution
Parameters
Default value
None
Usage condition
Notes
Input example
Output item
Related
commands
22-18
Monitors
Privilege
General
Save
Synchronize
SBY execution
Parameter
Default value
None
Usage condition
Note
Clearing a PVC also clears all the corresponding registered PVC counters.
Input example
Output item
Related
commands
22-19
Monitors
Privilege
General
Synchronize
SBY execution
Parameter
Default value
None
Usage condition
Note
None
Input example
Output items
Related
commands
22-20
Monitors
Privilege
General
Save
Synchronize
SBY execution
Parameter
Default value
None
Usage condition
Notes
Input example
Output item
Related
commands
22-21
Monitors
Privilege
General
Synchronize
SBY execution
Parameters
Default value
None
Usage condition
Notes
Using display of byte/frame counter information in PVC units requires that the PVC has
been registered in advance.
If the counter value exceeds the counter bit width, it is cleared to zero and then
incremented.
Counter values may be unable to be collected during system switching of SWITCH or
target PVC settings change.
When real or act-real is specified, up to 14 indexes will be displayed.
Display counters for act-real and act-detail collects count values of APS active side by
the update timing. If APS function is disabled at any update timing, then they collects
the counter value of the smaller number slot.
Input examples
22-22
Monitors
Count-End with [Ctrl]+[c]
*Switch@1#
Output items
[Realtime showing]
Port: Port (line) number
VPI/VCI: VPI/VCI values
Pkts(Rx): Number of receiving frames
Pkts(Tx): Number of sending frames
Entry:
registered: PVC counter registered
unregistered: PVC counter not registered
[Detailed showing]
Port: Port (line) number
VPI/VCI: VPI/VCI values
Name: PVC name
Entry:
registered: PVC counter registered
unregistered: PVC counter not registered
RxOcts: Number of receiving octets
RxPkts: Number of receiving frames
RxErrors: Number discarded receiving frames
TxOcts: Number of sending octets
TxPkts: Number of sending frames
Related
commands
22-23
Monitors
Privilege
General
Save
Synchronize
SBY execution
Parameter
Default value
None
Usage condition
This command can be used only for ATM155/ ATMP/ATMP155 line modules.
However, this command has no effect on ATMP/ATMP155 lines because there is no
information to be displayed for these lines.
To specify VPI-value/VCI-value or PVC-name, you can use registered PVC counters
only.
To specify a port set for APS operation, use the smaller slot number.
(The greater slot number cannot be specified.)
Notes
Input example
Output item
Related
command
22-24
Monitors
Privilege
General
Synchronize
SBY execution
Parameters
Default value
None
Usage condition
This command can be used only for ATM155/ ATMP/ATMP155 line modules.
To specify a port set for APS operation, use the smaller slot number.
(The greater slot number cannot be specified.)
To specify a port set for an IMA group, use the rout port line number.
(If a value other than the rout port line number is specified, an error occurs.)
Notes
If the counter value exceeds the counter bit width, it is cleared to zero and then
incremented.
Counter values may be unable to be collected during system switching of SWITCH or
target PVC settings change.
When real is specified, up to 14 indexes will be displayed.
In the case of OAM cell counters, only counters for registered PVCs are collected.
If a route port of an IMA group is specified, counter information will be displayed in IMA
group units. To display counter information for each port in an IMA group separately,
use the "show counter ima-port" command.
22-25
Monitors
Input examples
22-26
Monitors
Output items
Related
commands
[Realtime showing]
Port: Port (line) number
Cells(Rx): Number of receiving cells
Cells(Tx): Number of sending cells
Entry: Fixed to "---"
[Detailed showing]
Port:
RxCells:
RxErrors:
RxF4SegAIS:
RxF4SegRDI:
RxF4SegLoopback:
RxF4SegOthers:
RxF4EndAIS:
RxF4EndRDI:
RxF4EndLoopback:
RxF4EndOthers:
RxF5SegAIS:
RxF5SegRDI:
RxF5SegLoopback:
RxF5SegOthers:
RxF5EndAIS:
RxF5EndRDI:
RxF5EndLoopback:
RxF5EndOthers:
TxCells:
TxErrors:
TxF4SegAIS:
TxF4SegRDI:
TxF4SegLoopback:
TxF4SegOthers:
TxF4EndAIS:
TxF4EndRDI:
TxF4EndLoopback:
TxF4EndOthers:
TxF5SegAIS:
TxF5SegRDI:
TxF5SegLoopback:
TxF5SegOthers:
TxF5EndAIS:
TxF5EndRDI:
TxF5EndLoopback:
TxF5EndOthers:
22-27
Monitors
Privilege
General
Synchronize
SBY execution
Parameters
Default value
None
Usage condition
This command can be used only for ATM155/ ATMP/ATMP155 line modules.
To specify a port set for APS operation, use the smaller slot number.
(The greater slot number cannot be specified.)
To specify a port set for an IMA group, use the rout port line number.
(If a value other than the rout port line number is specified, an error occurs.)
Notes
Input examples
22-28
Monitors
F4-Cell Counter Table
=====================
Port
: 10/1
VPI
: 255
Entry : unregistered
Item
Counts | Item
Counts
----------------------------------------------------------+-----------RxCells
:
1234567890 | TxCells
:
1234567890
RxErrors
:
0 | TxErrors
:
0
RxF4SegAIS
:
0 | TxF4SegAIS
:
0
RxF4SegRDI
:
0 | TxF4SegRDI
:
0
RxF4SegLoopback :
0 | TxF4SegLoopback :
0
RxF4SegOthers :
0 | TxF4SegOthers
:
0
RxF4EndAIS
:
0 | TxF4EndAIS
:
0
RxF4EndRDI
:
0 | TxF4EndRDI
:
0
RxF4EndLoopback :
0 | TxF4EndLoopback :
0
RxF4EndOthers :
0 | TxF4EndOthers
:
0
RxF5SegAIS
:
0 | TxF5SegAIS
:
0
RxF5SegRDI
:
0 | TxF5SegRDI
:
0
RxF5SegLoopback :
0 | TxF5SegLoopback :
0
RxF5SegOthers :
0 | TxF5SegOthers
:
0
RxF5EndAIS
:
0 | TxF5EndAIS
:
0
RxF5EndRDI
:
0 | TxF5EndRDI
:
0
RxF5EndLoopback :
0 | TxF5EndLoopback :
0
RxF5EndOthers :
0 | TxF5EndOthers
:
0
*Switch@1#
Output items
[Realtime showing]
Port: Port (line) number
VPI: VPI value
Cells(Rx): Number of receiving cells
Cells(Tx): Number of sending cells
Entry:
registered: PVC counter registered
unregistered: PVC counter not registered
[Detailed showing]
Port: Port (line) number
VPI: VPI value
Entry:
registered: PVC counter registered
unregistered: PVC counter not registered
RxCells:
Number of receiving cells
RxErrors:
Number of discarded receiving cells
RxF4SegAIS:
VP-AIS cell of receiving segment
RxF4SegRDI:
VP-RDI cell of receiving segment
RxF4SegLoopback: Loopback cell of receiving F4-level segment
RxF4SegOthers:
Other receiving cells of F4-level segment
RxF4EndAIS:
VP-AIS cell of receiving end
RxF4EndRDI:
VP-RDI cell of receiving end
RxF4EndLoopback: Loopback cell of receiving F4-level end
RxF4EndOthers:
Other receiving cells of F4-level end
22-29
Monitors
RxF5SegAIS:
RxF5SegRDI:
RxF5SegLoopback:
RxF5SegOthers:
RxF5EndAIS:
RxF5EndRDI:
RxF5EndLoopback:
RxF5EndOthers:
TxCells:
TxErrors:
TxF4SegAIS:
TxF4SegRDI:
TxF4SegLoopback:
TxF4SegOthers:
TxF4EndAIS:
TxF4EndRDI:
TxF4EndLoopback:
TxF4EndOthers:
TxF5SegAIS:
TxF5SegRDI:
TxF5SegLoopback:
TxF5SegOthers:
TxF5EndAIS:
TxF5EndRDI:
TxF5EndLoopback:
TxF5EndOthers:
Related
commands
22-30
Monitors
Privilege
General
Synchronize
SBY execution
Parameters
Default value
None
Usage condition
This command can be used only for ATM155/ ATMP/ATMP155 line modules.
To specify a port set for APS operation, use the smaller slot number.
(The greater slot number cannot be specified.)
To specify a port set for an IMA group, use the rout port line number.
(If a value other than the rout port line number is specified, an error occurs.)
Notes
Using display of byte/frame counter information in PVC units requires that a PVC be
registered in advance.
If the counter value exceeds the counter bit width, it is cleared to zero and then
incremented.
Counter values may be unable to be collected during system switching of SWITCH or
target PVC settings change.
When real is specified, up to 14 indexes will be displayed.
In the case of OAM cell counters, only counters for registered PVCs are collected.
Values of F4 OAM cell counters for VP connection are fixed to zeros.
Input examples
22-31
Monitors
*Switch@1#
*Switch@1# show counter cell f5 detail 10/1 255/100
F5-Cell Counter Table
=====================
Port
: 10/1
VPI/VCI : 255/100
Entry : registered
Item
Counts | Item
Counts
----------------------------------------------------------+-----------RxCells
:
1234567890 | TxCells
:
1234567890
RxErrors
:
0 | TxErrors
:
0
RxF4SegAIS
:
0 | TxF4SegAIS
:
0
RxF4SegRDI
:
0 | TxF4SegRDI
:
0
RxF4SegLoopback :
0 | TxF4SegLoopback :
0
RxF4SegOthers :
0 | TxF4SegOthers
:
0
RxF4EndAIS
:
0 | TxF4EndAIS
:
0
RxF4EndRDI
:
0 | TxF4EndRDI
:
0
RxF4EndLoopback :
0 | TxF4EndLoopback :
0
RxF4EndOthers :
0 | TxF4EndOthers
:
0
RxF5SegAIS
:
0 | TxF5SegAIS
:
0
RxF5SegRDI
:
0 | TxF5SegRDI
:
0
RxF5SegLoopback :
0 | TxF5SegLoopback :
0
RxF5SegOthers
:
0 | TxF5SegOthers :
0
RxF5EndAIS
:
0 | TxF5EndAIS
:
0
RxF5EndRDI
:
0 | TxF5EndRDI
:
0
RxF5EndLoopback :
0 | TxF5EndLoopback :
0
RxF5EndOthers :
0 | TxF5EndOthers
:
0
*Switch@1#
Output items
[Realtime showing]
Port: Port (line) number
VPI/VCI: VPI/VCI values
Cells(Rx): Number of receiving cells
Cells(Tx): Number of sending cells
Entry:
registered: PVC counter registered
unregistered: PVC counter not registered
[Detailed showing]
Port: Port (line) number
VPI/VCI: VPI/VCI values
Entry:
registered: PVC counter registered
unregistered: PVC counter not registered
RxCells:
Number of receiving cells
RxErrors:
Number of discarded receiving cells
RxF4SegAIS:
VP-AIS cell of receiving segment
RxF4SegRDI:
VP-RDI cell of receiving segment
RxF4SegLoopback: Loopback cell of receiving F4-level segment
RxF4SegOthers:
Other receiving cells of F4-level segment
RxF4EndAIS:
VP-AIS cell of receiving end
22-32
Monitors
RxF4EndRDI:
RxF4EndLoopback:
RxF4EndOthers:
RxF5SegAIS:
RxF5SegRDI:
RxF5SegLoopback:
RxF5SegOthers:
RxF5EndAIS:
RxF5EndRDI:
RxF5EndLoopback:
RxF5EndOthers:
TxCells:
TxErrors:
TxF4SegAIS:
TxF4SegRDI:
TxF4SegLoopback:
TxF4SegOthers:
TxF4EndAIS:
TxF4EndRDI:
TxF4EndLoopback:
TxF4EndOthers:
TxF5SegAIS:
TxF5SegRDI:
TxF5SegLoopback:
TxF5SegOthers:
TxF5EndAIS:
TxF5EndRDI:
TxF5EndLoopback:
TxF5EndOthers:
Related
commands
22-33
Monitors
Privilege
General
Synchronize
SBY execution
Parameters
Default value
None
Usage
conditions
Notes
If the counter value exceeds the counter bit width, it is cleared to zero and then
incremented.
Counter values may be unable to be collected during system switching of SWITCH or
target PVC settings change.
When real is specified, up to 14 indexes will be displayed.
22-34
Monitors
Input examples
Output items
[Realtime showing]
Port: Port (line) number
Cells(Rx): Number of receiving cells
Cells(Tx): Number of sending cells
Entry: Fixed to "---"
[Detailed showing]
Port: Port (line) number
RxCells: Number of receiving cells
RxErrors:
Number of discarded receiving cells
TxCells: Number of sending cells
TxErrors: Number of discarded sending cells
Related
commands
22-35
Monitors
Privilege
General
Save
Synchronize
SBY execution
Parameter
Default value
None
Usage condition
This command can be used only for ATM155/ ATMP/ATMP155 line modules.
To specify VPI-value/VCI-value or PVC-name, you can use registered PVC counters
only.
To specify a port set for APS operation, use the smaller slot number.
(The greater slot number cannot be specified.)
To specify a port set for an IMA group, use the rout port line number.
(If a value other than the rout port line number is specified, an error occurs.)
Notes
Input example
Output item
Related
commands
22-36
Monitors
Privilege
General
Save
Synchronize
SBY execution
mirror port
Setting of mirroring start or stop
Sets mirroring start or stop.
Input formats
- Stopping mirroring
mirror port P1 (stop)
- Starting mirroring (with only input-side lines specified for mirroring target)
mirror port P1 (start) P2 P3
- Starting mirroring (with only output-side lines specified for mirroring target)
mirror port P1 (start) P2 P4
- Starting mirroring (with input- and output-side lines specified for mirroring
target)
mirror port P1 (start) P2 P3 P4
mirror port P1 (start) P2 P4 P3
Parameters
Default value
None
Usage condition
None
Notes
Input example
22-37
Monitors
Output item
Related
command
22-38
Monitors
Privilege
General
Synchronize
SBY execution
Parameter
None
Default value
None
Usage condition
None
Note
None
Input example
Output items
Related
command
mirror port
22-39
Monitors
(Blank page)
22-40
23 Maintenance and
Operation
23-1
General
Save
Synchronize
SBY execution
upload running-config
Uploading of running configuration to ftp server
Uploads running configuration to the ftp server.
Input format
upload running-config P1 P2
Parameters
P1: IP address
P2: File name or path name + file name (1 to 127 characters)
Default value
None
Usage conditions
Notes
Input example
Output items
Related
commands
23-2
General
Save
Synchronize
SBY execution
upload startup-config
Uploading of startup configuration to ftp server
Uploads startup configuration to the ftp server.
Input format
upload startup-config P1 P2
Parameters
P1: IP address
P2: File name or path name + file name (1 to 127 characters)
Default value
None
Usage conditions
Notes
Input example
Output items
Related
commands
23-3
General
Save
Synchronize
SBY execution
upload local-syslog
Uploading of system log to ftp server
Uploads the system log to the ftp server.
Input format
upload local-syslog P1 P2
Parameters
P1: IP address
P2: File name or path name + file name (1 to 127 characters)
Default value
None
Usage conditions
Notes
Input example
Output items
Related
commands
23-4
General
Save
Synchronize
SBY execution
upload all-information
Uploading of setting information to ftp server
Uploads setting information to the ftp server.
Input format
upload all-information P1 P2
Parameters
P1: IP address
P2: File name or path name + file name (1 to 127 characters)
Default value
None
Usage conditions
Notes
Input example
Output items
Related
command
23-5
General
Save
Synchronize
SBY execution
upload fault
Uploading of fault information to ftp server
Uploads fault information to the ftp server.
Input format
upload fault P1 P2
Parameters
P1: IP address
P2: File name or path name + file name (1 to 127 characters)
Default value
None
Usage conditions
Notes
Input example
Output items
Related
commands
23-6
General
Save
Synchronize
SBY execution
download software
Downloading of software
Downloads software.
Input format
download software P1 P2
Parameters
P1: IP address
P2: File name or path name + file name (1 to 127 characters)
Default value
None
Usage conditions
Notes
Input example
Output items
Related
commands
23-7
General
Save
Synchronize
SBY execution
Parameters
P1: IP address
P2: File name or path name + file name (1 to 127 characters)
Default value
None
Usage conditions
Note
Input example
Output items
23-8
23-9
General
Save
Synchronize
SBY execution
Parameters
P1: Line module type {fe | gbe | fe-pv | gbe-pv | gmx | atm | tdmp | atmp | gbe-pv2 |
atmp155 | tdmp155}
fe: Line module FE8/FX8
gbe: Line module GbE
fe-pv: Line module FE8-PV/FX8-PV
gbe-pv: Line module Gbe-PV
gmx: Line module GM8-T/GM8-X
atm: Line module ATM155
tdmp: Line module TDMP
atmp: Line module ATMP
gbe-pv2: Line module Gbe-PV2
atmp155: Line module ATMP155
tdmp155: Line module TDMP155
P2: IP address
P3: File name or path name + file name (1 to 127 characters)
Default value
None
Usage conditions
Notes
To reflect the downloaded data, you must enter the reset line command to reinitialize the
line module.
Set an ftp user name and FTP password interactively.
Set a file name or a path name + file name with ASCII characters other than ["], [?], and
[control character]. (However, you can use only the characters that can be recognized
by the ftp server.)
When using [space], enclose the entire character string in double quotation marks.
23-10
Output items
Related
command
23-11
General
Save
Synchronize
SBY execution
download running-config
Downloading of running configuration from ftp server
Downloads running configuration from the ftp server.
Input format
download running-config P1 P2
Parameters
P1: IP address
P2: File name or path name + file name (1 to 127 characters)
Default value
None
Usage conditions
Notes
No line module can be initialized during execution of this command. For this reason,
the line modules implemented during execution of this command are incorporated with
OUS state.
Also if a download file contains a command that involves line module initialization (e.g.,
set line type), the specified line module may be incorporated with OUS state.
After this command terminates, use the reset line command to reinitialize the line
module incorporated with OUS state.
ftp transfer may be performed several times according to the configuration size to be
downloaded.
Set an ftp user name and ftp password interactively.
Set a file name or a path name + file name with ASCII characters other than ["], [?], and
[control character]. (However, you can use only the characters that can be recognized
by the ftp server.)
When using [space], enclose the entire character string in double quotation marks.
Input example
Output items
23-12
23-13
General
Save
Synchronize
SBY execution
download startup-config
Downloading of startup configuration from ftp server
Downloads startup configuration from the ftp server.
Input format
download startup-config P1 P2
Parameters
P1: IP address
P2: File name or path name + file name (1 to 127 characters)
Default value
None
Usage conditions
Notes
ftp transfer may be performed several times according to the configuration size to be
downloaded.
Set an ftp user name and ftp password interactively.
Set a file name or a path name + file name with ASCII characters other than ["], [?], and
[control character]. (However, you can use only the characters that can be recognized
by the ftp server.)
When using [space], enclose the entire character string in double quotation marks.
Input example
Output items
Related
commands
23-14
General
Synchronize
SBY execution
show running-config
Display of running configuration
Shows the current running configuration.
Input format
Parameter
Default value
None
Usage condition
None
Note
None
Input example
Output item
23-15
upload running-config
download running-config
write memory
23-16
General
Synchronize
SBY execution
show startup-config
Display of startup configuration
Shows the saved startup configuration.
Input format
Parameter
Default value
None
Usage condition
None
Note
None
Input example
23-17
Related
commands
upload startup-config
download startup-config
write memory
clear startup-config
23-18
General
Synchronize
SBY execution
Parameter
None
Default value
None
Usage condition
None
Note
Since it takes times to show the result after command input, (dots) are shown.
Input example
Output items
Module: Module
Config: Difference between startup configuration and running configuration
same: There is no difference between startup configuration and running configuration
difference: There is a difference between startup configuration and running
configuration
Related
commands
download running-config
download startup-config
write memory
clear startup-config
23-19
General
Save
Synchronize
SBY execution
23-20
23-21
P4: enable
Usage condition
None
Note
None
23-22
Output item
Related
command
23-23
General
Synchronize
SBY execution
Parameter
Default value
None
Usage condition
None
Note
None
23-24
23-25
Output items
Related
command
23-26
General
Synchronize
SBY execution
show all
Display of all setting information
Shows all setting information.
Input format
Parameter
Default value
None
Usage condition
None
Note
Input example
23-27
Related
commands
23-28
General
Save
Synchronize
SBY execution
write memory
Saving of setting information
Saves the setting information.
Input format
Parameter
Default value
None
Usage condition
None
Note
None
Input example
Output item
Related
commands
upload running-config
upload startup-config
download running-config
download startup-config
show running-config
show startup-config
clear startup-config
23-29
General
Save
Synchronize
SBY execution
Parameter
Default value
None
Usage condition
None
Note
Input example
Output item
Related
commands
23-30
23-31
units
Setting of maximum band limiting function in output
VLAN units
Setting of priority mapping
Setting of input CoS priority mapping
Setting of output CoS priority mapping
Setting of burst tolerance of output-side fairness
control function of output port
Setting of output-side fairness control function
weight of output port
Set upper threshold of output-side fairness control
function of output port
Set spanning tree enable/disable per port
Setting of priority per port
Setting of path cost per port
Setting of edge port
Setting of point-to-point
Setting of link aggregation group
Setting of port priority
Setting /clearing of port isolate
Setting of input filtering
Setting of output filtering
Setting of MAC address learning count limiting
function
Setting of static MAC address of MAC address
learning count limiting function
Registration of PVC
Registration of PVC name
Setting of PVC blocking/unblocking
Setting of enbloc PVC blocking/unblocking
Setting of PVC-VLAN mode
Setting of VLAN VC
Setting of path between ATMs
Setting/clearing of PVC isolate
Setting/clearing of ATM loop guard
Setting of rate mode
Setting of ATM shaper
Setting of AAL5 mode
Setting of CLP
Setting of ATM-OAM operation
Setting of ATM-OAM flow point
Setting of ATM loopback monitoring function
Setting of M/C management function basics
Setting of VLAN counter collection conditions
Registration of PVC counter
Setting of mirroring start or stop
Setting of line module type
Setting of APS enable/disable
Setting of APS timer values
Setting of ATMoP format
Setting of ATMoP format
Setting of ATM-Ether conversion
23-32
General
Save
Synchronize
SBY execution
clear startup-config
Clearing of startup configuration
Clears startup configuration.
Input format
Parameters
Default value
None
Usage condition
None
Note
Input examples
all
data? :(Y/N): y
exip
data? :(Y/N): y
Output item
Related
commands
upload startup-config
download startup-config
show startup-config
write memory
23-33
General
Save
Synchronize
SBY execution
Parameters
P1: IP address
P2: FTP login name (1 to 16 characters)
Default value
None
Usage conditions
Notes
Input example
Output item
Related
commands
23-34
General
Save
Synchronize
SBY execution
Parameter
None
Default value
None
Usage condition
None
Note
None
Input example
Output item
Related
command
23-35
General
Save
Synchronize
SBY execution
Parameters
Default value
None
Usage condition
None
Note
Input example
Output item
Related
commands
23-36
General
Synchronize
SBY execution
Parameter
None
Default value
None
Usage condition
None
Note
None
Input example
Output items
Related
commands
23-37
General
Synchronize
SBY execution
Parameter
Default value
None
Usage condition
None
Note
None
Input example
23-38
Related
commands
23-39
General
Save
Synchronize
SBY execution
Parameter
None
Default value
None
Usage condition
None
Notes
Input example
Output item
Related
command
23-40
General
Synchronize
SBY execution
Parameter
None
Default value
None
Usage condition
None
Note
When a self exception or WDTOVF occurs, fault information can be saved every five
Main CPU faces and Sub CPU faces (to 20 faces).
Input example
23-41
Output items
Related
commands
23-42
General
Save
Synchronize
SBY execution
Parameter
None
Default value
None
Usage condition
None
Note
Input example
Output item
Related
command
23-43
General
Synchronize
SBY execution
Parameter
None
Default value
None
Usage condition
None
Note
This command also shows the module redundant configuration status and type
information.
Input example
23-44
Module: Module
Type: Module type
ugswc: UGSW module UGSWC
fe8: Line module FE8
fx8: Line module Fx8
gbe: Line module GbE
atm155: Line module ATM155
atmp: Line module ATMP
tdmp: Line module TDMP
tdmp155: Line module TDMP155
atmp155: Line module ATMP155
ac: Power module AC
dc: Power module DC
Status: Module status
unmount: Unmounted status
initializing: Initialization status
active: ACT status
standby: SBY status
out of service: Out-of-service status
mismatch: Incorrect insertion status
active-fault: ACT-FLT status
standby-fault: SBY-FLT status
Redundancy Mode: Redundancy mode
single-mode: Single mode
dual-fixed: Dual-fixed mode
Related
command
23-45
General
Synchronize
SBY execution
Parameter
None
Default value
None
Usage condition
None
Note
None
Input example
Output items
Related
command
None
23-46
General
Synchronize
SBY execution
Parameter
None
Default value
None
Usage condition
None
Note
None
Input example
23-47
Related
command
23-48
General
Synchronize
SBY execution
Parameter
None
Default value
None
Usage condition
None
Notes
Input example
23-49
Module: Module
Install: Installation status
ugswc: UGSW module
fe8: Line module FE8
fx8a: Line module Fx8a
fx8b: Line module Fx8b
fx8s: Line module Fx8s
gbe: Line module GbE
fe8-pv: Line module FE8-PV
fx8a-pv: Line module Fx8a-PV
fx8b-pv: Line module Fx8b-PV
fx8s-pv: Line module Fx8s-PV
gbe-pv: Line module GbE-PV
gm8-t: Line module GM8-T
gm8-x: Line module GM8-X
atm155s: Line module ATM155S
atm155m: Line module ATM155M
atmp: Line module ATMP
tdmp: Line module TDMP
tdmp155: Line module TDMP155
atmp155: Line module ATMP155
gbe-pv2: Line module GbE-PV2
Ver: Various version information
Related
command
23-50
General
Synchronize
SBY execution
Parameter
None
Default value
None
Usage condition
None
Note
None
Input example
23-51
Module: Module
Install: Installation status
ugswc: UGSW module
fe8: Line module FE8
fx8a: Line module Fx8a
fx8b: Line module Fx8b
fx8s: Line module Fx8s
gbe: Line module GbE
fe8-pv: Line module FE8-PV
fx8a-pv: Line module Fx8a-PV
fx8b-pv: Line module Fx8b-PV
fx8s-pv: Line module Fx8s-PV
gbe-pv: Line module GbE-PV
gm8-t: Line module GM8-T
gm8-x: Line module GM8-X
atm155s: Line module ATM155S
atm155m: Line module ATM155M
atmp: Line module ATMP
tdmp: Line module TDMP
tdmp155: Line module TDMP155
atmp155: Line module ATMP155
gbe-pv2: Line module GbE-PV2
Related
command
23-52
General
Save
Synchronize
SBY execution
Parameter
Default value
enable
Usage condition
None
Note
None
Input example
Output item
Related
command
23-53
General
Synchronize
SBY execution
Parameter
None
Default value
None
Usage condition
None
Note
None
Input example
*Switch@1#
*Switch@1# show fault auto-reboot
Fault AutoReboot Configuration
==============================
AutoReboot: enabled
*Switch@1#
Output item
Related
command
23-54
General
Synchronize
SBY execution
Parameter
None
Default value
None
Usage condition
None
Note
None
Input example
Output items
23-55
Related
command
None
23-56
General
Synchronize
SBY execution
Parameter
None
Default value
None
Usage condition
None
Note
None
Input example
Output items
Module: Module
Type: Module type
main: Main CPU
sub: Sub CPU
Related
command
None
23-57
(Blank page)
23-58
Device Control
24 Device Control
24-1
Device Control
Privilege
General
Save
Synchronize
SBY execution
Parameters
Default value
P2: none
Usage conditions
- You cannot change the line module type if a configuration other than the line module
type is already entered.
- You cannot set FE8/FX8 for line modules #5 to #12.
- You cannot set GM8-T/GM8-X.
Notes
Specifying the correct line module type for the slot that is in the MISMATCH status
initializes the line module. However, if the line module cannot be initialized because it
is in contention for another event, it is incorporated with OUS status.
After this command ends, reinitialize the line module incorporated with OUS status using
the reset line command.
Input example
Output item
Related
commands
24-2
Device Control
Privilege
General
Save
Synchronize
SBY execution
Parameters
24-3
Device Control
Default values
Usage
conditions
You can set the TDMP line mode only when the line type setting is tdmp, or none with a
TDMP line module installed.
To specify tdmop for P2, an error occurs if no TDMoP mode has been registered.
To specify tdmop for P2, e1 for P3 and unframed for P5, TDMoP operation mode must
have been set to SAToP mode.
You cannot change the TDMP line mode setting if any of the following commands is
already entered:
set tdm group
set tdmop group
set port cable-length
set ether-oam mep
To specify tdmop for P2, there is the following restriction on the number of TDMP line
modules and TDMP155 line modules:
(Number of TDMP line modules x 1) + (Number of TDMP155 line modules x 3) < 16
* The above numbers of line modules mean the ones set to TDMoP mode.
Note
If any of the following changes has been made while the line state is ACT, line restart
will be executed:
- Changing line mode from tdm to tdmop or none
- Changing line mode from tdmop to tdm or none
- Changing frame type
If a frame type is changed with this command, TDM group name setting of the line
module will be deleted.
Input examples
*Switch@1#
*Switch@1#
*Switch@1#
*Switch@1#
*Switch@1#
set
set
set
set
set
line
line
line
line
line
mode
mode
mode
mode
mode
tdmp
tdmp
tdmp
tdmp
tdmp
1
2
3
4
5
none
tdm e1 hdb3 crc4
tdm t1 b8zs
tdm e1 esf
tdmop t1 hdb3 unframed
Output item
Related
commands
24-4
Device Control
Privilege
General
Save
Synchronize
SBY execution
Parameters
Default values
24-5
Device Control
Usage
conditions
You can set the ATMP line mode only when the line type setting is atmp, or none with an
ATMP line module installed.
You cannot change the ATMP line mode setting if any of the following commands is
already entered:
set port cable-length
set ima group
set ima clock
Note
If any of the following changes has been made while the line state is ACT, line restart
will be executed:
- Changing line mode from atmop to none
- Changing frame type
Input examples
*Switch@1#
*Switch@1#
*Switch@1#
*Switch@1#
*Switch@1#
set
set
set
set
set
line
line
line
line
line
mode
mode
mode
mode
mode
atmp
atmp
atmp
atmp
atmp
1
2
3
4
5
none
atmop
atmop
atmop
atmop
e1
t1 b8zs
t1 esf
e1 hdb3 unframed
Output item
Related
commands
24-6
Device Control
Privilege
General
Save
Synchronize
SBY execution
Parameters
Default value
None
Usage
conditions
You can set the TDMP155 line mode only when the line type setting is tdmp155, or the
line type setting is none and a TDMP155 line module has been installed.
To specify tdmop for P2, an error occurs if no TDMoP mode has been registered.
You cannot change the TDMP155 line mode setting if any of the following commands is
already entered:
set tdm group
set tdmop group
set port logical-interface
set ether-oam mep
When APS is set to enabled, settings of the line module cannot be changed.
Notes
If any of the following changes has been made while the line state is ACT, line restart will
be executed:
- Changing line mode from tdm to tdmop or none
- Changing line mode from tdmop to tdm or none
- Changing frame type
If a frame type is changed with this command, TDM group name setting of the line
module will be deleted.
Input example
24-7
Device Control
Output item
Related
commands
24-8
Device Control
Privilege
General
Save
Synchronize
SBY execution
Parameters
Default value
P2: none
Usage
conditions
- You cannot change the line module type if a configuration other than the line module
type is already entered.
- You cannot set the GbE line mode for line modules #5 to #12.
- You can set the GbE line mode only when the line module type is gbe, or the line
module type setting is none and a GbE-PV or GbE-PV2 line module has been installed.
- When a GbE-PV line module is installed, operation in FE mode is not allowed although
setting of each line mode is available. (A link down will occur in the GbE port.)
Note
If any of the following changes has been made while the line state is ACT, line restart will
be executed:
- Changing line mode from none or gbe to fe
- Changing line mode from fe to none or gbe
Input example
Output item
Related
commands
24-9
Device Control
Privilege
General
Synchronize
SBY execution
Parameter
None
Default value
None
Usage condition
None
Note
None
Input example
Output items
24-10
Device Control
Related
commands
24-11
Device Control
Privilege
General
Save
Synchronize
SBY execution
change switch
Changeover of UGSW module system
Changes the UGSW module system.
Input format
Parameter
Default value
None
Usage condition
None
Notes
When the UGSW module system is changed forcibly, the old ACT side enters the OUS
status. When the old ACT side is in the ACT-FLT status, the UGSW module system
enters the SBY-FLT status.
Input example
Output item
Related
command
24-12
Device Control
Privilege
General
Save
Synchronize
SBY execution
reset system
Resetting of entire device
Resets the entire device.
Input format
reset system
Parameter
None
Default value
None
Usage condition
None
Notes
Input example
System Boot
Copyright 2001-2002 NEC
24-13
Device Control
Output item
Related
commands
reset switch
reset line
show reset
24-14
Device Control
Privilege
General
Save
Synchronize
SBY execution
reset switch
Resetting of UGSW module
Reset the UGSW module.
Input format
Parameters
Default value
None
Usage conditions
You cannot specify the backup face when resetting the mate system.
You cannot reset the ACT system when the UGSW module is in the ACT or SBY status
(including the FLT status).
Notes
Input example
System Boot
Copyright 2001-2002 NEC
24-15
Device Control
CPU: PPC 405GP
Version: 5.4
BSP version: 1.2/5
Boot version: K01.00
Creation date: Mar 31 2004, 14:38:54
Output item
Related
commands
reset system
show reset
24-16
Device Control
Privilege
General
Save
Synchronize
SBY execution
reset line
Resetting of line module
Resets a line module.
Input format
reset line P1
Parameter
Default value
None
Usage conditions
Whether you can enter this command depends on the following line statuses:
Status
Can be entered/cannot
be entered
unmount
initializing
active
standby
out of service
mismatch
active-fault
standby-fault
Note
Input example
Output item
Related
commands
24-17
Device Control
Privilege
General
Synchronize
SBY execution
show reset
Display of reset factor
Shows a UGSW module reset factor.
Input format
Parameter
Default value
None
Usage condition
None
Note
Specifying the detail parameter shows reset factors in CPU units, not in UGSW module
units.
Input example
Output items
Module: Module
Type: Module type
ugswc: UGSW module
main: main CPU
sub: sub CPU
Reset Factor: Reset factor
Power On Reset or Switch Module Insertion: Power-on reset or module insertion
Command Reset(reset system): Command reset by reset system
Command Reset(reset switch):
The status of WDT is abnormal: Reset based on hardware judgment
The fatal error has occurred: Reset based on software judgment
Command Reset by mate(reset system):
Command reset by reset system from mate system
Command Reset by mate(reset switch):
Command reset by reset switch from mate system
Related
commands
reset system
reset switch
24-18
Device Control
Privilege
General
Save
Synchronize
SBY execution
ous switch
OUS setting of UGSW module
Sets OUS of the UGSW module.
Input format
ous switch P1
Parameter
Default value
None
Usage condition
None
Notes
Input example
Output item
Related
command
24-19
Device Control
Privilege
General
Save
Synchronize
SBY execution
ous line
OUS setting of line module
Sets OUS of a line module.
Input format
ous line P1 P2
Parameter
Default value
None
Usage condition
Note
Input example
Output item
Related
commands
24-20
Device Control
Privilege
General
Save
Synchronize
SBY execution
ous external-memory
Removing of external memory
Removes external memory.
Input format
ous external-memory
Parameter
None
Default value
None
Usage conditions
You can execute this command only when external memory is inserted.
Operate external memory in maintenance mode.
Note
Entering this command disables external memory access because external memory is
disconnected from the device. If you want to access external memory again, you must
reinsert it.
Input example
Output item
Related
command
None
24-21
Device Control
(Blank page)
24-22
Maintenance Mode
25 Maintenance Mode
25-1
Maintenance Mode
Maintenance
Save
Synchro
-nize
SBY
execution
download software
Downloading of software
Downloads software.
Input format
download software P1 P2
Parameters
Default value
None
Usage condition
You can execute this command only when external memory is inserted.
Notes
To reflect downloaded data, you must enter the reset switch or reset system command
to reinitialize the Switch module.
You can specify a path with an absolute or relative path name. However, if a relative
path name of 127 characters or less (including the file name) is converted to an absolute
path name of more than 246 characters, an error occurs. Paths of up to 20 directory
hierarchies are permissible. No file can be specified beyond 21 directory hierarchies.
If no path is specified, current directory specification is assumed.
Set a file name or a path name + file name with ASCII characters other than ["], [?], and
[control character].
When using [space], enclose the entire character string in double quotation marks.
Input example
Output item
Related
commands
reset system
reset switch
ous external-memory
25-2
Maintenance Mode
Maintenance
Save
Synchro
-nize
SBY
execution
Parameters
Default value
None
Usage condition
You can execute this command only when external memory is inserted.
Notes
To reflect downloaded data, you must enter the reset switch command specifying
fpga-version-up parameter to reinitialize the Switch module.
You can specify a path with an absolute or relative path name. However, if a relative
path name of 127 characters or less (including the file name) is converted to an absolute
path name of more than 246 characters, an error occurs. Paths of up to 20 directory
hierarchies are permissible. No file can be specified beyond 21 directory hierarchies.
If no path is specified, current directory specification is assumed.
Set a file name or a path name + file name with ASCII characters other than ["], [?], and
[control character].
When using [space], enclose the entire character string in double quotation marks.
Input example
25-3
Maintenance Mode
Output item
Related
commands
reset switch
ous external-memory
25-4
Maintenance Mode
Maintenance
Save
Synchro
-nize
SBY
execution
Parameters
Default value
None
Usage condition
You can execute this command only when external memory is inserted.
Notes
To reflect downloaded data, you must enter the reset line command to reinitialize the
line module.
You can specify a path with an absolute or relative path name. However, if a relative
path name of 127 characters or less (including the file name) is converted to an absolute
path name of more than 246 characters, an error occurs. Paths of up to 20 directory
hierarchies are permissible. No file can be specified beyond 21 directory hierarchies.
If no path is specified, current directory specification is assumed.
Set a file name or a path name + file name with ASCII characters other than ["], [?], and
[control character].
When using [space], enclose the entire character string in double quotation marks.
25-5
Maintenance Mode
Input example
Output item
Related
commands
reset line
ous external-memory
25-6
Maintenance Mode
Maintenance
Save
Synchro
-nize
SBY
execution
Parameter
Default value
None
Usage condition
You can execute this command only when external memory is inserted.
Notes
You can specify a path with an absolute or relative path name. However, if a relative
path name of 127 characters or less (including the file name) is converted to an absolute
path name of more than 246 characters, an error occurs. Paths of up to 20 directory
hierarchies are permissible. No file can be created beyond 21 directory hierarchies.
If no path is specified, current directory specification is assumed.
The maximum length of a file name is 99 characters.
Set a file name or a path name + file name with alphanumeric characters and % & , / = [
] ^ _ { } ~ . .
You can use / only when specifying a path name, and . only when specifying a file
name.
Configuration information which is uploaded is the same as the information displayed by
the show running-config command.
Input example
Output item
Related
commands
show running-config
Display of running configuration
download running-config external-memory
Download running configuration from external
memory
write memory external-memory
Save setting information to external memory
ous external-memory
Remove external memory
25-7
Maintenance Mode
Maintenance
Save
Synchro
-nize
SBY
execution
Parameter
Default value
None
Usage condition
You can execute this command only when external memory is inserted.
Notes
You can specify a path with an absolute or relative path name. However, if a relative
path name of 127 characters or less (including the file name) is converted to an absolute
path name of more than 246 characters, an error occurs. Paths of up to 20 directory
hierarchies are permissible. No file can be created beyond 21 directory hierarchies.
If no path is specified, current directory specification is assumed.
The maximum length of a file name is 99 characters.
Set a file name or a path name + file name with alphanumeric characters and % & , / = [
] ^ _ { } ~ . .
You can use / only when specifying a path name, and . only when specifying a file
name.
Configuration information which is uploaded is the same as the information displayed by
the show startup-config command.
Input example
Output item
Related
commands
show startup-config
Display of startup configuration
clear startup-config
Clearing of startup configuration
download startup-config external-memory
Downloading of startup configuration from external
memory
write memory external-memory
Saving of setting information to external memory
25-8
Maintenance Mode
Maintenance
Save
Synchro
-nize
SBY
execution
upload local-syslog
Uploading of system log to external memory
Uploads a system log to external memory.
Input format
upload local-syslog P1 P2
Parameters
Default value
None
Usage condition
You can execute this command only when external memory is inserted.
Notes
You can specify a path with an absolute or relative path name. However, if a relative
path name of 127 characters or less (including the file name) is converted to an absolute
path name of more than 246 characters, an error occurs. Paths of up to 20 directory
hierarchies are permissible. No file can be created beyond 21 directory hierarchies.
If no path is specified, current directory specification is assumed.
The maximum length of a file name is 99 characters.
Set a file name or a path name + file name with alphanumeric characters and % & , / = [
] ^ _ { } ~ . .
You can use / only when specifying a path name, and . only when specifying a file
name.
Local syslog information which is uploaded is the same as the information displayed by
the show local syslog command.
Input example
Output item
Related
commands
25-9
Maintenance Mode
Maintenance
Save
Synchro
-nize
SBY
execution
Parameter
Default value
None
Usage condition
You can execute this command only when external memory is inserted
Notes
You can specify a path with an absolute or relative path name. However, if a relative
path name of 127 characters or less (including the file name) is converted to an absolute
path name of more than 246 characters, an error occurs. Paths of up to 20 directory
hierarchies are permissible. No file can be specified beyond 21 directory hierarchies.
If no path is specified, current directory specification is assumed.
External memory may be accessed several times according to the configuration size to
be downloaded.
Set a file name or a path name + file name with ASCII characters other than ["], [?], and
[control character].
When using [space], enclose the entire character string in double quotation marks.
Input example
Output item
Related
commands
show running-config
Display of running configuration
upload running-config external-memory
Uploading of running configuration to external
memory
write memory external-memory
Saving of setting information to external memory
ous external-memory
Removing of external memory
25-10
Maintenance Mode
Maintenance
Save
Synchro
-nize
SBY
execution
Parameter
Default value
None
Usage condition
You can execute this command only when external memory is inserted.
Notes
You can specify a path with an absolute or relative path name. However, if a relative
path name of 127 characters or less (including the file name) is converted to an absolute
path name of more than 246 characters, an error occurs. Paths of up to 20 directory
hierarchies are permissible. No file can be specified beyond 21 directory hierarchies.
If no path is specified, current directory specification is assumed.
External memory may be accessed several times according to the configuration size to
be downloaded.
Set a file name or a path name + file name with ASCII characters other than ["], [?], and
[control character].
When using [space], enclose the entire character string in double quotation marks.
Input example
Output item
Related
commands
clear startup-config
Clearing of startup configuration
upload startup-config external-memory
Uploading of startup configuration to external
memory
write memory external-memory
Saving of setting information to external memory
ous external-memory
Removing of external memory
25-11
Maintenance Mode
Maintenance
Save
Synchro
-nize
SBY
execution
upload fault
Uploading of fault information to external memory
Uploads fault information to external memory.
Input format
upload fault P1 P2
Parameters
Default value
None
Usage condition
You can execute this command only when external memory is inserted.
Notes
You can specify a path with an absolute or relative path name. However, if a relative
path name of 127 characters or less (including the file name) is converted to an absolute
path name of more than 246 characters, an error occurs. Paths of up to 20 directory
hierarchies are permissible. No file can be created beyond 21 directory hierarchies.
If no path is specified, current directory specification is assumed.
The maximum length of a file name is 99 characters.
Set a file name or a path name + file name with alphanumeric characters and % & , / = [
] ^ _ { } ~ . .
You can use / only when specifying a path name, and . only when specifying a file
name.
Fault information which is uploaded is the same as the information displayed by the
show fault present and show fault past commands.
Input example
Output item
Related
commands
25-12
Maintenance Mode
Maintenance
Save
Synchro
-nize
SBY
execution
Parameter
Default value
None
Usage condition
You can execute this command only when external memory is inserted.
Notes
You can specify a path with an absolute or relative path name. However, if a relative
path name of 127 characters or less (including the file name) is converted to an absolute
path name of more than 246 characters, an error occurs. Paths of up to 20 directory
hierarchies are permissible. No file can be created beyond 21 directory hierarchies.
If no path is specified, current directory specification is assumed.
The maximum length of a file name is 99 characters.
Set a file name or a path name + file name with alphanumeric characters and % & , / = [
] ^ _ { } ~ . .
You can use / only when specifying a path name, and . only when specifying a file
name.
Setting information which is uploaded is the same as the information shown by the
show all command.
Input example
Output item
Related
command
show all
25-13
Maintenance Mode
Maintenance
Save
Synchro
-nize
SBY
execution
write memory
Saving of setting status to external memory
Saves the setting status to external memory.
Input format
Parameters
Default value
None
Usage condition
You can execute this command only when external memory is inserted.
Note
The setting status is saved to the /auto_reflect directory in external memory under the
startup-config.scfg file name. If the /auto_reflect directory does not exist, it is
automatically created.
Input example
Output item
Related
commands
show running-config
Display of running configuration
show startup-config
Display of startup configuration
clear startup-config
Clearing of startup configuration
upload running-config external-memory
Uploading of running configuration to external memory
upload startup-config external-memory
Uploading of startup configuration to external memory
download running-config external-memory
Downloading of running configuration from external memory
download startup-config external-memory
Downloading of startup configuration from external memory
ous external-memory
Removing of external memory
25-14
Maintenance Mode
Maintenance
Save
Synchro
-nize
SBY
execution
end
Switch from maintenance mode to privileged mode
Enables you to switch from maintenance mode to privileged mode.
Input format
end
Parameter
None
Default value
None
Usage condition
None
Note
None
Input example
*Switch@1% end
*Switch@1#
Output item
Related
command
maintenance
25-15
Maintenance Mode
Maintenance
Save
Synchro
-nize
SBY
execution
dir
Display of directory list
Shows a directory list.
Input format
dir [P1]
Parameter
Default value
None
Usage condition
You can execute this command only when external memory is inserted.
Notes
You can specify a path with an absolute or relative path name. However, if a relative
path name of 127 characters or less is converted to an absolute path name of more than
246 characters, an error occurs. Paths of up to 20 directory hierarchies are
permissible. No directory can be referenced beyond 21 directory hierarchies.
Set a path name with alphabets, numeric characters, and symbols and signs % & , = [ ]
^ _ { } ~ /.
Input example
Switch@1% dir
11/26/2004 15:59:08 <DIR>
11/26/2004 15:59:42 <DIR>
11/26/2004 16:05:18
11/26/2004 16:06:36
4096 cx2600
4096 auto_reflect
246 testConfig.scfg
246 testConfig2.scfg
Switch@1% dir
Output items
Related
commands
mkdir
rmdir
cd
ous external-memory
Creating of directory
Removing of directory
Change of current directory
Removing of external memory
25-16
Maintenance Mode
Maintenance
Save
Synchro
-nize
SBY
execution
mkdir
Creating of directory
Creates a directory.
Input format
mkdir P1
Parameter
Default value
None
Usage condition
You can execute this command only when external memory is inserted.
Notes
An error occurs if the directory name is used in a file name in the same directory.
You can specify a path with an absolute or relative path name. However, if a relative
path name of 127 characters or less (including the created directory name) is converted
to an absolute path name of more than 246 characters, an error occurs. Paths of up to
20 directory hierarchies are permissible. No directory can be created beyond 21
directory hierarchies.
If no path is specified, current directory specification is assumed.
The maximum length of a directory name is 99 characters.
Set a directory name or a path name + directory name with alphanumeric characters
and % & , = [ ] ^ _ { } ~ /.
Input example
Output item
Related
command
dir
rmdir
cd
ous external-memory
25-17
Maintenance Mode
Maintenance
Save
Synchro
-nize
SBY
execution
rmdir
Removing of directory
Removes a directory.
Input format
rmdir P1
Parameter
Default value
None
Usage condition
You can execute this command only when external memory is inserted.
Notes
You can specify a path with an absolute or relative path name. However, if a relative
path name of 127 characters or less (including the deleted directory name) is converted
to an absolute path name of more than 246 characters, an error occurs. If no path is
specified, current directory specification is assumed. Paths of up to 20 directory
hierarchies are permissible. No directory can be specified beyond 21 directory
hierarchies.
Set a directory name or a path name + directory name with alphanumeric characters
and % & , = [ ] ^ _ { } ~ /.
Input example
Output item
Related
command
mkdir
dir
cd
ous external-memory
Creating of directory
Display of directory list
Change of current directory
Removing of external memory
25-18
Maintenance Mode
Maintenance
Save
Synchro
-nize
SBY
execution
cd
Change of current directory
Changes the current directory.
Input format
cd [P1]
Parameter
Default value
Usage condition
You can execute this command only when external memory is inserted.
Notes
You can specify a path with an absolute or relative path name. However, if a relative
path name of 127 characters or less is converted to an absolute path name of more than
246 characters, an error occurs. If no path is specified, current directory specification is
assumed. Paths of up to 20 directory hierarchies are permissible. No directory can
be specified beyond 21 directory hierarchies.
Set a path name with alphanumeric characters and % & , = [ ] ^ _ { } ~ /.
Input example
Switch@1% cd /auto_reflect
Switch@1%
Switch@1% cd
/auto_reflect
Switch@1%
Output item
Related
command
mkdir
dir
rmdir
ous external-memory
Creating of directory
Display of directory list
Removing of directory
Removing of external memory
25-19
Maintenance Mode
Maintenance
Save
Synchro
-nize
SBY
execution
copy
Copying file
Copies a file.
Input format
copy P1 P2
Parameters
P1: Copy source fie name or copy source path name + file name (1 to 127 characters)
P2: Copy destination file name or copy destination path name + file name (1 to 127
characters)
Default value
None
Usage condition
You can execute this command only when external memory is inserted.
Notes
An error occurs if the copy destination file name is used in a directory name in the same
directory.
You can specify a path with an absolute or relative path name. However, if a relative
path name of 127 characters or less (including the file name) is converted to an absolute
path name of more than 246 characters, an error occurs. Paths of up to 20 directory
hierarchies are permissible. No file can be created beyond 21 directory hierarchies.
If no path is specified, current directory specification is assumed.
The maximum length of a copy destination file name is 99 characters.
Set a copy source file name, a copy source path name + file name, or a copy destination
path name + file name with alphanumeric characters and % & , = [ ] ^ _ { } ~ /..
You can use / only when specifying a path name and . only when specifying a file
name.
Input example
Output item
Related
command
rename
del
ous external-memory
25-20
Maintenance Mode
Maintenance
Save
Synchro
-nize
SBY
execution
rename
Change of file name
Changes a file name.
Input format
rename P1 P2
Parameters
P1: Pre-change file name or pre-change path name + file name (1 to 127 characters)
P2: Post-change file name (1 to 99 characters)
Default value
None
Usage condition
You can execute this command only when external memory is inserted.
Notes
An error occurs if the post-change file name is used in a directory name in the same
directory.
You can specify a path with an absolute or relative path name. However, if a relative
path name of 127 characters or less (including the file name) is converted to an absolute
path name of more than 246 characters, an error occurs. Paths of up to 20 directory
hierarchies are permissible. No file can be specified beyond 21 directory hierarchies.
If no path is specified, current directory specification is assumed.
Set a pre-change file name, a pre-change path name + file name, or a post-change file
name with alphanumeric characters and % & , = [ ] ^ _ { } ~ /..
You can use / only when specifying a path name and . only when specifying a file
name.
Input example
Output item
Related
command
copy
del
ous external-memory
Copying file
Deleting file
Removing of external memory
25-21
Maintenance Mode
Maintenance
Save
Synchro
-nize
SBY
execution
del
Deleting file
Deletes a file.
Input format
del P1
Parameter
Default value
None
Usage condition
You can execute this command only when external memory is inserted.
Notes
You can specify a path with an absolute or relative path name. However, if a relative
path name of 127 characters or less (including the file name) is converted to an absolute
path name of more than 246 characters, an error occurs. Paths of up to 20 directory
hierarchies are permissible. No file can be specified beyond 21 directory hierarchies.
If no path is specified, current directory specification is assumed.
Set a file name or a path name + file name with alphanumeric characters and % & , = [ ]
^ _ { } ~ /..
You can use / only when specifying a path name and . only when specifying a file
name.
Input example
Output item
Related
command
copy
rename
ous external-memory
Copying file
Change of file name
Removing of external memory
25-22
Maintenance Mode
Maintenance
Privilege
Synchro
-nize
Save
SBY
execution
ous external-memory
Removing of external memory
Removes external memory.
Input format
ous external-memory
Parameter
None
Default value
None
Usage condition
You can execute this command only when external memory is inserted.
Note
Entering this command disables external memory access because external memory is
disconnected from the device. If you want to access external memory again, you must
reinsert it.
Input example
Output item
Related
commands
mkdir
dir
rmdir
cd
copy
rename
del
Creating of directory
Display of directory list
Removing of directory
Change of current directory
Coping file
Change of file name
Deleting file
25-23
Maintenance Mode
Maintenance
Save
Synchro
-nize
SBY
execution
Parameter
None
Default value
None
Usage condition
None
Note
None
Input example
Output item
Related
command
None
25-24
Appendix
26 Appendix
26-1
Appendix
Appendix 1
The table below lists the commands shown by show running-config, show startup-config, and show
all.
Shown by
show running-config or
show startup-config
(write memory)
change aps
change ether-ps
change external-clock
change switch
date
dm ether-oam
linktrace ether-oam
lm ether-oam
loopback atm
loopback ether-oam
loopback ima
loopback mc
mirror port
ous line
ous switch
reset line
reset reference-clock
reset switch
reset system
set aps
set atm-loop
set atm-oam
Command
26-2
Appendix
Shown by
show running-config or
show startup-config
(write memory)
set command-mode
set ether-oam cc
set ether-oam lm
set ether-ps
set frame-size
set igmp
Command
26-3
Appendix
Shown by
show running-config or
show startup-config
(write memory)
set ip route
set ip virtual-address
set mc management
Command
26-4
Appendix
Shown by
show running-config or
show startup-config
(write memory)
{ *1
set snmp
set spantree
Command
26-5
Appendix
Shown by
show running-config or
show startup-config
(write memory)
Command
26-6
Appendix
Shown by
show running-config or
show startup-config
(write memory)
show command-mode
show ether-oam lm
Command
26-7
Appendix
Shown by
show running-config or
show startup-config
(write memory)
{ (Detailed showing)
show frame-size
show ip config
show mc information
{ (Outline showing)
Command
26-8
Appendix
Shown by
show running-config or
show startup-config
(write memory)
show ntp
show reset
{ (Outline showing)
show session
show snmp
Command
26-9
Appendix
Shown by
show running-config or
show startup-config
(write memory)
Command
*1 show running-config and show startup-config are output by set qos out-weight fairness.
{: Shown
: Not shown
: Not applicable
26-10
Appendix
Appendix 2
The table below lists operation restrictions on commands per line module.
Operation restrictions
Command
GbEPV
GbEPV2
FE-PV
FX-PV
ATM
155
ATMP
ATMP
155
TDMP
TDMP
155
GbE8MUX
change aps
change ether-ps
change external-clock
change switch
date
dm ether-oam
linktrace ether-oam
lm ether-oam
loopback atm
loopback ether-oam
loopback ima
loopback mc
mirror port
ous line
ous switch
reset line
reset reference-clock
reset switch
reset system
set aps
set atm-loop
set atm-oam
26-11
Appendix
Operation restrictions
Command
GbEPV
GbEPV2
FE-PV
FX-PV
ATM
155
ATMP
ATMP
155
TDMP
TDMP
155
GbE8MUX
set command-mode
set ether-oam cc
set ether-oam lm
set ether-ps
set frame-size
set igmp
set ip route
26-12
Appendix
Operation restrictions
Command
GbEPV
GbEPV2
FE-PV
FX-PV
ATM
155
ATMP
ATMP
155
TDMP
TDMP
155
GbE8MUX
set ip virtual-address
set mc management
26-13
Appendix
Operation restrictions
Command
GbEPV
GbEPV2
FE-PV
FX-PV
ATM
155
ATMP
ATMP
155
TDMP
TDMP
155
GbE8MUX
set snmp
set spantree
26-14
Appendix
Operation restrictions
Command
GbEPV
GbEPV2
FE-PV
FX-PV
ATM
155
ATMP
ATMP
155
TDMP
TDMP
155
GbE8MUX
26-15
Index
Index
C
cd ............................................................................................................................................... 25-19
change aps .................................................................................................................................. 12-6
change aps reset ......................................................................................................................... 12-8
change ether-ps ......................................................................................................................... 11-45
change ether-ps reset ................................................................................................................ 11-46
change external-clock ................................................................................................................ 19-10
change switch ............................................................................................................................ 24-12
clear aggregation group ............................................................................................................... 9-27
clear atm-fdb table pvc............................................................................................................... 13-26
clear atm-loop ............................................................................................................................ 13-30
clear atmop format ..................................................................................................................... 13-36
clear atm-qos out-port clp .......................................................................................................... 14-15
clear atm-shaper rate................................................................................................................. 14-10
clear backup server.................................................................................................................... 23-35
clear counter cell........................................................................................................................ 22-36
clear counter port ......................................................................................................................... 22-5
clear counter pvc entry............................................................................................................... 22-21
clear counter pvc value .............................................................................................................. 22-24
clear counter vlan entry.............................................................................................................. 22-18
clear counter vlan value ............................................................................................................. 22-13
clear enable password ................................................................................................................... 2-7
clear ether-oam fault reason ...................................................................................................... 11-30
clear ether-oam lm ..................................................................................................................... 11-13
clear ether-oam meg.................................................................................................................... 11-5
clear ether-oam mep.................................................................................................................. 11-10
clear ether-oam mip ................................................................................................................... 11-19
clear ether-oam peer-mep ......................................................................................................... 11-15
clear fault past............................................................................................................................ 23-43
clear fault warning...................................................................................................................... 23-40
clear fdb limiter........................................................................................................................... 10-20
clear fdb limiter static ................................................................................................................. 10-22
Index-1
Index
clear fdb table port ....................................................................................................................... 8-12
clear fdb table vid......................................................................................................................... 8-14
clear filter in-port ........................................................................................................................ 10-12
clear filter out-port ...................................................................................................................... 10-16
clear filter profile........................................................................................................................... 10-8
clear igmp mac............................................................................................................................. 9-37
clear igmp vid............................................................................................................................... 9-40
clear ima group ............................................................................................................................ 16-9
clear ip address in-band................................................................................................................. 4-6
clear ip address out-band .............................................................................................................. 4-3
clear ip route ................................................................................................................................ 4-12
clear ip route default ...................................................................................................................... 4-8
clear ip virtual-address................................................................................................................. 4-21
clear login password ...................................................................................................................... 2-9
clear loopback atm keepalive..................................................................................................... 21-22
clear ntp server .......................................................................................................................... 20-28
clear pvc connection .................................................................................................................. 13-40
clear pvc name............................................................................................................................. 13-5
clear pvc static ............................................................................................................................. 13-3
clear pvc-vlan table .................................................................................................................... 13-12
clear qos cos-map profile............................................................................................................. 7-48
clear qos in-port cos-map ............................................................................................................ 7-51
clear qos in-rate maximum........................................................................................................... 7-19
clear qos out-port cos-map .......................................................................................................... 7-54
clear qos out-rate maximum ........................................................................................................ 7-35
clear qos out-weight fairness ....................................................................................................... 7-69
clear running-config line............................................................................................................. 23-30
clear session .............................................................................................................................. 20-14
clear session ip-permit ............................................................................................................... 20-12
clear snmp manager .................................................................................................................... 20-5
clear snmp trap-manager............................................................................................................. 20-6
clear startup-config .................................................................................................................... 23-33
clear syslog local........................................................................................................................ 20-24
clear syslog map ........................................................................................................................ 20-21
clear syslog server ..................................................................................................................... 20-18
clear system daylight-time ........................................................................................................... 3-12
clear tdm group ............................................................................................................................ 17-6
Index-2
Index
clear tdm group-name................................................................................................................ 17-12
clear tdm path ............................................................................................................................ 17-18
clear tdmop adaptive-clock ........................................................................................................ 18-36
clear tdmop connection.............................................................................................................. 18-15
clear tdmop format ..................................................................................................................... 18-29
clear tdmop group ........................................................................................................................ 18-9
clear tdmop mode ........................................................................................................................ 18-4
clear user account........................................................................................................................ 2-18
clear vlan name............................................................................................................................ 6-16
clear vlan swap ............................................................................................................................ 6-11
clear vlan tagbase.......................................................................................................................... 6-3
copy ........................................................................................................................................... 25-20
D
date ................................................................................................................................................ 3-6
del .............................................................................................................................................. 25-22
dir ............................................................................................................................................... 25-16
disable............................................................................................................................................ 2-4
dm ether-oam............................................................................................................................. 11-35
download fpga line ............................................................................................................ 23-10, 25-5
download fpga switch.......................................................................................................... 23-8, 25-3
download running-config............................................................................................................ 23-12
download running-config external-memory................................................................................ 25-10
download software .............................................................................................................. 23-7, 25-2
download startup-config............................................................................................................. 23-14
download startup-config external-memory ................................................................................. 25-11
E
enable ............................................................................................................................................ 2-3
end ............................................................................................................................................. 25-15
exit ................................................................................................................................................. 2-2
Index-3
Index
L
linktrace ether-oam .................................................................................................................... 11-33
lm ether-oam.............................................................................................................................. 11-37
loopback atm................................................................................................................................ 21-9
loopback ether-oam ................................................................................................................... 11-31
loopback ima.............................................................................................................................. 16-12
loopback mc................................................................................................................................. 21-3
M
maintenance .................................................................................................................................. 2-5
mirror port .................................................................................................................................. 22-37
mkdir .......................................................................................................................................... 25-17
O
ous external-memory ...................................................................................................... 24-21, 25-23
ous line....................................................................................................................................... 24-20
ous switch .................................................................................................................................. 24-19
P
ping .............................................................................................................................................. 4-18
R
rename....................................................................................................................................... 25-21
reset line .................................................................................................................................... 24-17
reset reference-clock ................................................................................................................... 19-9
reset switch ................................................................................................................................ 24-15
reset system............................................................................................................................... 24-13
rmdir........................................................................................................................................... 25-18
Index-4
Index
S
set aggregation group .................................................................................................................. 9-24
set aggregation port priority ......................................................................................................... 9-30
set aggregation protection-time ................................................................................................... 9-32
set aggregation system priority .................................................................................................... 9-28
set aps ......................................................................................................................................... 12-2
set aps lockout ............................................................................................................................. 12-4
set aps time.................................................................................................................................. 12-5
set atm-loop ............................................................................................................................... 13-27
set atmop format ........................................................................................................................ 13-32
set atmop mode ......................................................................................................................... 13-31
set atm-qos aal5 ........................................................................................................................ 14-11
set atm-qos out-port clp ............................................................................................................. 14-13
set atm-shaper mode ................................................................................................................... 14-2
set atm-shaper rate........................................................................................................... 14-3, 14-16
set backup schedule .................................................................................................................. 23-36
set backup server....................................................................................................................... 23-34
set command-mode ..................................................................................................................... 2-19
set counter pvc entry.................................................................................................................. 22-19
set counter vlan entry................................................................................................................. 22-14
set enable password ...................................................................................................................... 2-6
set ether-oam cc ........................................................................................................................ 11-24
set ether-oam frame................................................................................................................... 11-20
set ether-oam lm ........................................................................................................................ 11-11
set ether-oam meg....................................................................................................................... 11-2
set ether-oam mep....................................................................................................................... 11-6
set ether-oam mip ...................................................................................................................... 11-16
set ether-oam peer-mep ............................................................................................................ 11-14
set ether-oam rdi........................................................................................................................ 11-26
set ether-oam reply-period......................................................................................................... 11-22
set ether-ps ................................................................................................................................ 11-40
set ether-ps control-vlan ............................................................................................................ 11-42
set ether-ps lockout.................................................................................................................... 11-43
set ether-ps time ........................................................................................................................ 11-44
set external-clock mode ............................................................................................................... 19-2
set fault auto-reboot ................................................................................................................... 23-53
set fdb agingtime............................................................................................................................ 8-4
Index-5
Index
set fdb limiter.............................................................................................................................. 10-17
set fdb limiter static .................................................................................................................... 10-21
set filter in-port ............................................................................................................................. 10-9
set filter out-port ......................................................................................................................... 10-13
set filter profile.............................................................................................................................. 10-4
set frame-size ................................................................................................................................ 8-2
set ifg over-rate ............................................................................................................................ 8-15
set igmp ....................................................................................................................................... 9-34
set ima clock .............................................................................................................................. 16-10
set ima group ............................................................................................................................... 16-2
set in-band admin ........................................................................................................................ 4-13
set in-band vid.............................................................................................................................. 4-14
set ip address in-band.................................................................................................................... 4-4
set ip address out-band ................................................................................................................. 4-2
set ip in-band mode ..................................................................................................................... 4-22
set ip route ..................................................................................................................................... 4-9
set ip route default ......................................................................................................................... 4-7
set ip virtual-address.................................................................................................................... 4-19
set isolate port.............................................................................................................................. 10-2
set isolate pvc ............................................................................................................................ 13-17
set l2p-transparent reserved-mac ................................................................................................ 9-22
set l2p-transparent stp-bpdu ........................................................................................................ 9-20
set line mode atmp....................................................................................................................... 24-5
set line mode gbe......................................................................................................................... 24-9
set line mode tdmp....................................................................................................................... 24-3
set line mode tdmp155................................................................................................................. 24-7
set line type.................................................................................................................................. 24-2
set login password ......................................................................................................................... 2-8
set loopback atm keepalive........................................................................................................ 21-18
set loopback atm keepalive-mode ............................................................................................. 21-14
set loopback atm source-id ........................................................................................................ 21-12
set mc management .................................................................................................................... 21-2
set message transmit................................................................................................................. 23-20
set ntp access-time .................................................................................................................... 20-25
set ntp server ............................................................................................................................. 20-26
set oam ............................................................................................................................... 15-2, 15-4
set out-band flowcontrol............................................................................................................... 4-16
Index-6
Index
set out-band speed ...................................................................................................................... 4-15
set port admin ................................................................................................................................ 5-2
set port cable-length .................................................................................................................... 5-19
set port clock.................................................................................................................................. 5-9
set port flowcontrol......................................................................................................................... 5-6
set port frame............................................................................................................................... 5-10
set port impedance ...................................................................................................................... 5-26
set port link-trap ............................................................................................................................. 5-8
set port logical-interface............................................................................................................... 5-23
set port protection-time .................................................................................................................. 5-7
set port speed ................................................................................................................................ 5-3
set port type ................................................................................................................................... 5-5
set pvc admin............................................................................................................................... 13-6
set pvc connection ..................................................................................................................... 13-37
set pvc name................................................................................................................................ 13-4
set pvc port admin........................................................................................................................ 13-7
set pvc static ................................................................................................................................ 13-2
set pvc-vlan mode...................................................................................................................... 13-10
set pvc-vlan table ....................................................................................................................... 13-11
set qos class-map ........................................................................................................................ 7-37
set qos class-map profile ............................................................................................................. 7-40
set qos cos-map profile................................................................................................................ 7-43
set qos in-class-map maximum ..................................................................................................... 7-9
set qos initial-priority .................................................................................................................... 7-75
set qos in-port cos-map ............................................................................................................... 7-49
set qos in-priority maximum ......................................................................................................... 7-12
set qos in-rate maximum................................................................................................................ 7-6
set qos maximum-mode................................................................................................................. 7-2
set qos measure-cycle ................................................................................................................. 7-80
set qos out-class-map maximum ................................................................................................. 7-24
set qos out-fairness-mode ........................................................................................................... 7-55
set qos out-port cos-map ............................................................................................................. 7-52
set qos out-priority fairness.......................................................................................................... 7-57
set qos out-priority maximum....................................................................................................... 7-28
set qos out-rate fairness maximum-port ...................................................................................... 7-64
set qos out-rate maximum ........................................................................................................... 7-21
set qos out-weight fairness .......................................................................................................... 7-62
Index-7
Index
set qos out-weight rate................................................................................................................. 7-60
set reference-clock mode............................................................................................................. 19-6
set reference-clock priority........................................................................................................... 19-4
set session ip-permit .................................................................................................................. 20-10
set snmp ...................................................................................................................................... 20-2
set snmp authen-trap ................................................................................................................... 20-7
set snmp manager ....................................................................................................................... 20-3
set snmp trap-manager................................................................................................................ 20-4
set spantree ................................................................................................................................... 9-2
set spantree mode ......................................................................................................................... 9-3
set spantree port .......................................................................................................................... 9-10
set spantree port cost .................................................................................................................. 9-12
set spantree port edge ................................................................................................................. 9-15
set spantree port point-to-point .................................................................................................... 9-17
set spantree port priority .............................................................................................................. 9-11
set spantree priority ....................................................................................................................... 9-5
set spantree time ........................................................................................................................... 9-6
set spantree txholdcount................................................................................................................ 9-7
set syslog map ........................................................................................................................... 20-19
set syslog remote....................................................................................................................... 20-15
set syslog server ........................................................................................................................ 20-16
set system contact ......................................................................................................................... 3-2
set system daylight-time ................................................................................................................ 3-8
set system location ........................................................................................................................ 3-4
set system name............................................................................................................................ 3-3
set system timezone ...................................................................................................................... 3-7
set tdm group ............................................................................................................................... 17-2
set tdm group-name..................................................................................................................... 17-8
set tdm path ............................................................................................................................... 17-14
set tdmop adaptive-clock ........................................................................................................... 18-33
set tdmop admin ........................................................................................................................ 18-31
set tdmop connection................................................................................................................. 18-11
set tdmop format ........................................................................................................................ 18-23
set tdmop group ........................................................................................................................... 18-5
set tdmop jitter ........................................................................................................................... 18-17
set tdmop mode ........................................................................................................................... 18-2
set terminal logout........................................................................................................................ 2-14
Index-8
Index
set terminal monitor ..................................................................................................................... 2-13
set terminal prompt ...................................................................................................................... 2-10
set terminal scroll local................................................................................................................. 2-12
set terminal scroll system............................................................................................................. 2-11
set user account........................................................................................................................... 2-16
set vlan ethertype......................................................................................................................... 6-13
set vlan member ............................................................................................................................ 6-8
set vlan name............................................................................................................................... 6-15
set vlan portbase............................................................................................................................ 6-4
set vlan swap ................................................................................................................................. 6-9
set vlan tagbase............................................................................................................................. 6-2
show aggregation group .............................................................................................................. 9-25
show aggregation port priority...................................................................................................... 9-31
show aggregation protection-time................................................................................................ 9-33
show aggregation system priority ................................................................................................ 9-29
show all ...................................................................................................................................... 23-27
show aps information ................................................................................................................... 12-9
show atm-fdb count pvc ............................................................................................................. 13-22
show atm-fdb count vid .............................................................................................................. 13-24
show atm-fdb table pvc .............................................................................................................. 13-19
show atm-fdb table vid ............................................................................................................... 13-20
show atm-loop config ................................................................................................................. 13-28
show atm-loop information......................................................................................................... 13-29
show atmop format .................................................................................................................... 13-34
show atm-qos aal5..................................................................................................................... 14-12
show atm-qos out-port clp............................................................................................... 14-14, 14-19
show atm-shaper information....................................................................................................... 14-8
show atm-shaper rate .................................................................................................................. 14-6
show backup information ........................................................................................................... 23-37
show command-mode.................................................................................................................. 2-20
show config difference ............................................................................................................... 23-19
show counter cell ....................................................................................................................... 22-25
show counter cell f4 ................................................................................................................... 22-28
show counter cell f5 ................................................................................................................... 22-31
show counter cell ima-port ......................................................................................................... 22-34
show counter discard ................................................................................................................... 22-6
show counter port ........................................................................................................................ 22-2
Index-9
Index
show counter pvc entry .............................................................................................................. 22-20
show counter pvc value ............................................................................................................. 22-22
show counter vlan entry ............................................................................................................. 22-16
show counter vlan value .............................................................................................................. 22-8
show ether-oam fault last-change.............................................................................................. 11-27
show ether-oam fault reason ..................................................................................................... 11-28
show ether-oam frame ............................................................................................................... 11-21
show ether-oam lm .................................................................................................................... 11-12
show ether-oam meg ................................................................................................................... 11-3
show ether-oam mep ................................................................................................................... 11-8
show ether-oam mip .................................................................................................................. 11-17
show ether-oam reply-period ..................................................................................................... 11-23
show ether-ps config.................................................................................................................. 11-47
show ether-ps status.................................................................................................................. 11-49
show fault auto-reboot ............................................................................................................... 23-54
show fault past ........................................................................................................................... 23-41
show fault present...................................................................................................................... 23-38
show fdb agingtime ........................................................................................................................ 8-5
show fdb count all .......................................................................................................................... 8-9
show fdb count port........................................................................................................................ 8-6
show fdb count vid ......................................................................................................................... 8-8
show fdb limiter .......................................................................................................................... 10-18
show fdb table.............................................................................................................................. 8-10
show fdb table port....................................................................................................................... 8-11
show fdb table vid ........................................................................................................................ 8-13
show filter in-port........................................................................................................................ 10-10
show filter out-port ..................................................................................................................... 10-14
show filter profile .......................................................................................................................... 10-6
show frame-size............................................................................................................................. 8-3
show ifg over-rate ........................................................................................................................ 8-16
show igmp mac ............................................................................................................................ 9-36
show igmp port............................................................................................................................. 9-39
show igmp status ......................................................................................................................... 9-35
show igmp vid .............................................................................................................................. 9-38
show ima clock........................................................................................................................... 16-11
show ima group config ................................................................................................................. 16-4
show ima group status ................................................................................................................. 16-5
Index-10
Index
show in-band information............................................................................................................... 4-5
show ip config .............................................................................................................................. 4-10
show isolate port .......................................................................................................................... 10-3
show isolate pvc......................................................................................................................... 13-18
show l2p-transparent reserved-mac ............................................................................................ 9-23
show l2p-transparent stp-bpdu .................................................................................................... 9-21
show line mode .......................................................................................................................... 24-10
show loopback atm keepalive config ......................................................................................... 21-15
show loopback atm keepalive information ................................................................................. 21-20
show loopback atm source-id .................................................................................................... 21-13
show mc information .................................................................................................................... 21-6
show message transmit config................................................................................................... 23-24
show mirror port ......................................................................................................................... 22-39
show ntp..................................................................................................................................... 20-27
show oam config .......................................................................................................................... 15-6
show oam status .......................................................................................................................... 15-8
show out-band information........................................................................................................... 4-17
show port cable-length................................................................................................................. 5-21
show port impedance................................................................................................................... 5-27
show port information................................................................................................................... 5-11
show port logical-interface ........................................................................................................... 5-25
show port protection-time............................................................................................................. 5-18
show port trap .............................................................................................................................. 5-16
show pvc connection.................................................................................................................. 13-39
show pvc information ................................................................................................................... 13-8
show pvc-vlan table pvc............................................................................................................. 13-13
show pvc-vlan table vid.............................................................................................................. 13-15
show qos class-map .................................................................................................................... 7-38
show qos class-map profile.......................................................................................................... 7-42
show qos cos-map profile ............................................................................................................ 7-46
show qos initial-class-map ........................................................................................................... 7-73
show qos initial-priority................................................................................................................. 7-78
show qos in-port cos-map............................................................................................................ 7-50
show qos in-rate maximum .......................................................................................................... 7-16
show qos maximum-mode ............................................................................................................. 7-4
show qos measure-cycle ............................................................................................................. 7-81
show qos out-fairness-mode........................................................................................................ 7-56
Index-11
Index
show qos out-port cos-map.......................................................................................................... 7-53
show qos out-rate maximum........................................................................................................ 7-32
show qos out-weight fairness....................................................................................................... 7-66
show reference-clock information ................................................................................................ 19-7
show reset.................................................................................................................................. 24-18
show resource cpu..................................................................................................................... 23-55
show resource memory.............................................................................................................. 23-57
show running-config................................................................................................................... 23-15
show session ............................................................................................................................. 20-13
show session ip-permit .............................................................................................................. 20-11
show snmp................................................................................................................................... 20-8
show spantree info......................................................................................................................... 9-8
show spantree mode...................................................................................................................... 9-4
show spantree port ...................................................................................................................... 9-13
show spantree port edge ............................................................................................................. 9-16
show spantree port point-to-point ................................................................................................ 9-18
show startup-config.................................................................................................................... 23-17
show stm status ........................................................................................................................... 5-28
show switch status ..................................................................................................................... 25-24
show syslog local ....................................................................................................................... 20-22
show syslog map ....................................................................................................................... 20-20
show syslog server .................................................................................................................... 20-17
show system bridge ................................................................................................................... 23-46
show system date ........................................................................................................................ 3-11
show system information ............................................................................................................... 3-5
show system module-id ............................................................................................................. 23-47
show system revision................................................................................................................. 23-49
show system status.................................................................................................................... 23-44
show system temperature.......................................................................................................... 23-51
show tdm group ........................................................................................................................... 17-4
show tdm group-name ............................................................................................................... 17-10
show tdm path............................................................................................................................ 17-16
show tdmop adaptive-clock........................................................................................................ 18-35
show tdmop connection ............................................................................................................. 18-13
show tdmop format .................................................................................................................... 18-26
show tdmop information............................................................................................................... 18-7
show tdmop jitter........................................................................................................................ 18-19
Index-12
Index
show tdmop status ..................................................................................................................... 18-21
show terminal config .................................................................................................................... 2-15
show user account ....................................................................................................................... 2-17
show vlan ethertype ..................................................................................................................... 6-14
show vlan summary ..................................................................................................................... 6-12
show vlan swap............................................................................................................................ 6-10
show vlan table port ....................................................................................................................... 6-5
show vlan table vid......................................................................................................................... 6-7
U
update mc information ................................................................................................................. 21-5
upload all-information................................................................................................................... 23-5
upload all-information external-memory..................................................................................... 25-13
upload fault ....................................................................................................................... 23-6, 25-12
upload local-syslog ............................................................................................................. 23-4, 25-9
upload running-config .................................................................................................................. 23-2
upload running-config external-memory ...................................................................................... 25-7
upload startup-config ................................................................................................................... 23-3
upload startup-config external-memory ....................................................................................... 25-8
V
virtual-ping ................................................................................................................................... 4-20
W
write memory .................................................................................................................. 23-29, 25-14
Index-13
Index
(Blank page)
Index-14