Академический Документы
Профессиональный Документы
Культура Документы
Instructions
for use:
Steel industry
Coloured metal industry
Glass industry
Mining industry
Tunnel construction
Advantages:
fluids.
Compatibility Seals:
Standard materials like NBR (ISO 1629) are compatible, but there are
:
many producers on the market - therefore we recommend consulting the
seal producer or the Quaker laboratory. Excellent results are given by
FPM (ISO 1629), which is suitable for high temperatures.
Metals:
QUINTOLUBRIC 888-68 is compatible with steel and steel alloys, and
with most coloured metals and their alloys. QUINTOLUBRIC 888-68 is
not compatible with alloys that contain a lot of lead. Components
containing alloys with a lot of lead should be exchanged for more
suitable materials. For zinc see chapter: colours.
Remaining fluids:
QUINTOLUBRIC 888-68 is usually compatible with other HFDU fluids
and mineral oils, but we recommend performing a test program before
each change of fluid.
QUINTOLUBRIC 888-68 does not mix with water or water solutions; it
is compatible with QUINTOLUBRIC series 888, 840 and 850 fluids.
Colours:
Colour coatings inside hydraulic equipment usually are not necessary
since QUINTOLUBRIC 888-68 assures adequate corrosion protection.
QUINTOLUBRIC 888-68 is consistent with multi-component epoxy
coats. You should pay attention to compatibility when zinc coatings are
used, because they are not compatible in all cases. If inside the hydraulic
system coatings are required, we recommend consulting with the coat
producer or the Quaker laboratory.
To keep QUINTOLUBRIC 888-68 in a good condition it must be
Fluid
Maintenance: prevented from coming into contact with water and regularly filtered. It
is necessary to avoid high temperatures and to inspect the state of the oil
twice a year (the acidic value is an important indication of the products
condition).
Safety information, which is required for health and safety in the work
Safety:
environment are described in the Material Safety Data Sheet (MSDS).
The MSDS is enclosed in the first delivery and it is regularly renewed.
Storage:
The product can be stored min. 6 months under the following conditions:
Maximum long term storage temperature: 40 0C.
Minimum long term storage temperature: 0 0C.
Containers or barrels have to be tightly closed.
Containers or barrels have to be stored in dry and well ventilated space.
Quality
assurance:
Properties:
Property
Appearance
Kinetic viscosity
at -10 C
at 0 C
at 20 C
at 40 C
at 10 0C
Viscosity index
Refraction quotient at 20 C
Density at 15 C
Acidic value
Pour point
Foam test
at 25 C
after 10 minute
Corrosion protection
Flash-point
Focus point
Water content
Air separation
Soap number
Ignition temperature
Factory Mutual Spray-test
Lubrication test, Vickers 104C
(100 hour at 13.79 + 0.28 Mpa)
FZG test
Specific heat at 20 oC
Coefficient of thermic
expansion at 20 oC
Method
QTN* G 001
ASTM D-445
DIN 51564
DIN 51423
ASTM D-1298
QTN* A 004
ASTM D-97
ASTM D-892
CETOP R 48H
ASTM D-92
ASTM D-92
QTN* Z 046
ASTM D-3427
QTN* C 012
DIN 51794
Factory Mutual
(Factory test)
ASTM D-2882
DIN 51354/2
ASTM D-2766
ASTM D-1903
Typical value
Unit
Yellow to amber fluid 760
500
150
68
14
215
1.475
0.920
1.1
< - 25
mm2/s
mm2/s
mm2/s
mm2/s
mm2/s
-
30
0
meets
295
350
max. 0.05
4
175
> 400
meets
ml
ml
C
C
%
min.
mg KOH/g
C
-
<50
12
2.06
mg
load level
kJ/kg.0C
6 x 10-4
at 0C
g/cm3
mg KOH/g
C