Академический Документы
Профессиональный Документы
Культура Документы
WELDING INSPECTION
General Theory Paper QWI-4
Multichoice marks:
Name
:_____________________
Date
:_____________________
1.
Result: _ x 100 =
30
2.
When using a d.c. current the arc may deviate this is known as:
a.
b.
c.
d.
3.
4.
Arc strike.
Arc blow.
Paramagnetic influence.
None of the above.
Normalising.
Annealing.
Post hydrogen release.
All of the above.
WI Paper QWI-4
R&TPO-rrr QWI4
Date: 05/01/04 issue
5
5.
6.
Assuming no PWHT has been carried out, which is usually the hardest
part of a weld zone on a multi-run butt weld on low alloy steels.
a.
b.
c.
d.
7.
9.
The cap.
The root.
The HAZ of the cap.
The HAZ of the root.
8.
Which of the following would not normally be checked when two pipes
are butted up together prior to welding.
a.
b.
c.
d.
WI Paper QWI-4
R&TPO-rrr QWI4
Date: 05/01/04 issue
5
Cyclic stresses.
Corrosion.
Sudden stresses acting transverse to the material.
Poor through ductility caused through impurities originating in the
parent material.
11. Why is the cap on a butt weld sometimes limited to a specified height?
a.
b.
c.
d.
e.
12.
Magnetic particle.
Radiography
Dye Penetrant.
Ultrasonic.
WI Paper QWI-4
R&TPO-rrr QWI4
Date: 05/01/04 issue
5
15. Fluctuating loads, below the u.t.s. on a welded component may lead to:
a.
b.
c.
d.
Fatigue failures.
Ductile failures.
Weld decay, especially in austenitic stainless steel.
All of the above.
16. Which of the following may be used to measure the root radius of a
charpy specimen?
a.
b.
c.
d.
A shadow graph.
A micrometer.
A vernier calliper.
A densitometer.
Magnetic particle.
Dye Penetrant.
Radiography.
Ultrasonic.
All NDT methods can detect surface and sub-surface defects.
19. Which of the following NDT methods would you not expect to see applied
to an austenitic stainless steel weldment
a.
b.
c.
d.
Ultrasonic.
Magnetic particle.
Dye Penetrant..
Both a and b.
WI Paper QWI-4
R&TPO-rrr QWI4
Date: 05/01/04 issue
5
20.
Grain refinement.
Reducing carbon contents.
Hydrogen release.
Stress relief.
WI Paper QWI-4
R&TPO-rrr QWI4
Date: 05/01/04 issue
5
25. Which of the following electrodes would you expect to have the highest
elongation value?
a.
b.
c.
d.
E51
E43
E80
E90
28. When considering weld metal deposition, some of the core wore is lost
during welding, this is most likely due to:
a.
b.
c.
d.
Welding fumes
Spatter
The creation of a thermal blanket(slag)
None of the above
WI Paper QWI-4
R&TPO-rrr QWI4
Date: 05/01/04 issue
5
Radiography
Ultrasonic testing
Dye penetrant
Lamellar tearing cannot be detected using NDE
WI Paper QWI-4
R&TPO-rrr QWI4
Date: 05/01/04 issue
5
WI Paper QWI-4
R&TPO-rrr QWI4
Date: 05/01/04 issue
5
1.
2.
3.
4.
5.
6.
7.
8.
9.
10. A
11. E
12. C
13. C
14. B
15. A
16. A
17. B
18. B
19. E
20. B
WI Paper QWI-4