Академический Документы
Профессиональный Документы
Культура Документы
Instruction
Code No. 0816672
Rev.2 (07/15)
AER-DEC-81000/82000/83000/84000
Integrated Sink System
Single/Double/Triple/Quadruple Station Corian or Quartz Lavatory Systems
AD-81000
Deck Sink Lavatory System
AD-82000
Deck Sink Lavatory System
AD-83000
Deck Sink Lavatory System
AD-84000
Deck Sink Lavatory System
IMPORTANT
Read this entire installation manual to ensure proper installation.
When finished with the installation, file this manual with the owner
or maintenance department. Compliance and conformity to local
codes and ordinances is the responsibility of the installers.
Separate parts from packaging and make sure all parts are
accounted for before discarding any packaging material. If any
parts are missing, do not begin installation until you obtain the
missing parts.
Make sure that all water supply lines have been flushed and then
completely turned off before beginning installation. Debris in supply
lines can cause valves to malfunction.
Turn OFF electrical power to the electrical outlets, then unplug all
electrical units prior to installation. Electrical power MUST remain
off until installation is complete.
Installers hardware must be appropriate for wall construction. Wall
anchors must have a minimum pull-out rating of 1,000 lbs.
For standard height mounting, do not exceed the recommended
34 distance from the top of the lav deck to the finished floor. To
meet ADA requirements, the lav deck cannot exceed the
34 maximum height dimension.
Wear all proper safety equipment prior to installation.
PRIOR TO INSTALLATION
Important:
Adequate structural support in or behind the wall is required. Refer to the
appropriate rough-in diagram for dry weight of sink.
Refer to pages 10 and 11 for sink and stud support requirements.
LIMITED WARRANTY
Unless otherwise noted, Sloan Valve Company warrants its Products to be made of first class materials, free from defects of material or workmanship under normal use and to
perform the service for which they are intended in a thoroughly reliable and efficient manner when properly installed and serviced, for a period of three years (1 year for SF Faucets, special finishes and PWT electronics and 30 days on PWT software) from date of purchase. During this period, Sloan Valve Company will, at its option, repair or replace
any part or parts which prove to be thus defective if returned to Sloan Valve Company, at customers cost, and this shall be the sole remedy available under this warranty. No
claims will be allowed for labor, transportation or other incidental costs. This warranty extends only to persons or organizations who purchase Sloan Valve Companys products
directly from Sloan Valve Company for purpose of resale. This warranty does not cover the life of the batteries.
THERE ARE NO WARRANTIES WHICH EXTEND BEYOND THE DESCRIPTION ON THE FACE HEREOF. IN NO EVENT IS SLOAN VALVE COMPANY RESPONSIBLE FOR
ANY CONSEQUENTIAL DAMAGES OF ANY MEASURE WHATSOEVER.
Drain
clean-out
Hot
water
supply
34
22
backing
material
21
frame 2
33 to top
of frame
6 1/4 x 9 1/4 x 7.63
Soap Reservior
1/2 or 5/8
x 30 x 22
backing material
3/4 (not supplied)
securely fasten to
studs
Finished Floor
NOTES:
1. Mount Hand Dryer Motor Hose and soap dispenser to spec. location
2. Slip frame over mounted components and properly fasten frame to
backing material
LAVATORY SYSTEM ROUGH-IN PLUMBING & ELECTRICAL DIMENSIONS FRONT VIEW SINGLE STATION
(1) GFI Receptacle for soap
& sensor faucets, Transformer
Plug 120V/20AMP required by
National Electrical Code
30
Fasten frame to
1/8 thick steel
strapping or backing
material
4
33 to top
of frame
Hot
water
supply
7 1/2
Soap
Reservior
26
Water Supplies
30 Basin
ONLY
Cold Water Supply
Hand dryer
motor
mounting
plate
34
23
A.F.F.
19
Drain
Finished Floor
NOTES:
1. Hand Dryer Motor alone is only 500 watts or less with speed control
2. Hand Dryer Motor with heater requires 1500 watts or less with speed control
3. Hand Dryer Motor must be plugged into a dedicated 20 amp GFI safety circuit
4. Hand Dryer Motor to have a dedicated circuit with power cord and grounded plug
5. cut backing to allow for electrical and plumbing components
ROUGH-IN PLUMBING & ELECTRICAL
Sloan BASYS
Hand Dryer Spout
(patent applied for)
1/2 Solid surface
1/2 Backing Material
1/4 x 4 Steel plate
Vented basin design
(patent applied for)
Drain box & clean out
(patent applied for)
6 Max.
Optional aluminum
C-Channel w/LEDs
inside tract (120 volt
transformer required)
Stainless steel
34
access door
hangs on
27
rectangular
tubing frame
Push button latches snap
into place inside tubing
Finished Floor
3
1/2
1
Air dam
(patent applied for)
5 1/2
3/4
7 1/4
8 min.
16 1/8
Access
panel
11 1/8
11
6 max.
9
Drywall
17 min.
20 23
Water A.F.F.
Supplies
12 to
19 drain
bottom
of frame 14
to bottom
NOTE:
of Dryer
1. Backing material
Mounting
should equal thickness
Plate
of drywall (1/2 min.)
Hand
Dryer
Motor
21
frame
Sloan BASYS
Mid Faucet Spout
8 1/2
Sloan BASYS
Hand Dryer
5 3/8
Drain w/clean-out
GRID STRAINER TO BE CLEANED
OUT AS REQUIRED
3/4
23 1/2
Sloan Foam
Soap Dispenser
1/2
1 3/4
21
30
4 1/2
4 1/2
2x10 wood
reinforcement
between studs
33"
*Due to manufacturing
tolerances, all dimensions
are for reference only.
Soap Reservior
Lag Bolts
12
6
12
12
Access Panel
MOUNTING FAUCETS, SOAP DISPENSERS & HAND DRYERS / ATTACHING DECK TO FRAME ENCLOSURE SINGLE STATION
Adhesive
BASYS DRYER
SPOUT SUBASSEMBLY
HOLDING NUT
ASSEMBLY
FRAME SUPPORT
1. Back edge of Deck may require scribing to finished wall.
2. Shim all gaps between frame and deck,
especialy under trough area.
CONNECT CONTROL
CABLE TO HAND DRYER
MOTOR
EHD-510
BAYONET TURN
TO LOCK HOSE
TO SPOUT
PROGRAMING
CABLE. LEAVE
UNATTACHED
HOLDING NUT
ASSEMBLY
CONNECT GROUND
WIRE TO HAND
DRYER MOTOR
SOAP DISPENSER
LINES
POWER ADAPTOR
BAYONET TURN
TO LOCK HOSE TO
HAND DRYER MOTOR
SOAP DISPENSER
MOTOR ASSEMBLY
Brace
Brace
11 1/2
22
Backing
21
frame
34
33
to top
of frame
LAVATORY SYSTEM ROUGH-IN PLUMBING & ELECTRICAL DIMENSIONS FRONT VIEW DOUBLE STATION
60
Hand dryer
motor
mounting
plate
33 to
34 top of frame
10 3/4
Soap
Reservior
9 1/4
11 1/2
6
Soap
Reservior
20
5
water
supplies Hot
water
supply
Cold
water
supply
Fasten frame to
1/8 thick steel
strapping or backing
material
Standard 3 x 5
duplex receptacles
per sink manufacturer
requirements
Hand dryer
motor
mounting
plate
23
A.F.F.
Finished floor
NOTES:
1. Hand Dryer Motor alone is only 500 watts or less with speed control
2. Hand Dryer Motor with heater requires 1500 watts or less with speed control
3. Hand Dryer Motor must be plugged into a dedicated 20 amp GFI safety circuit
4. Hand Dryer Motor to have a dedicated circuit with power cord and grounded plug
5. cut backing to allow for electrical and plumbing components
ROUGH-IN PLUMBING & ELECTRICAL
Sloan BASYS
Hand Dryer Spout
(patent applied for)
1/2 Solid surface
1/2 Backing Material
1/4 x 4 Steel plate
Vented basin design
(patent applied for)
Drain box & clean out
(patent applied for)
6 Max.
Optional aluminum
C-Channel w/LEDs
inside tract (120 volt
transformer required)
Stainless steel
34
access door
hangs on
27
rectangular
tubing frame
Push button latches snap
into place inside tubing
Finished Floor
3
1/2
1
Air dam
(patent applied for)
5 1/2
3/4
7 1/4
8 min.
16 1/8
Access
panel
11 1/8
11
6 max.
9
Drywall
17 min.
20 23
Water A.F.F.
Supplies
12 to
19 drain
bottom
14
of frame
to bottom
NOTE:
of Dryer
1. Backing material
Mounting
should equal thickness
Plate
of drywall (1/2 min.)
Hand
Dryer
Motor
21
frame
6 1/2
8 1/2
6 1/2
7 1/2
Sloan BASYS
Hand Dryer
7 1/2
Sloan BASYS
Mid Faucet
Sloan Foam
soap dispensers
5 3/8
3/4
Drain w/clean-out
Grid strainer to be cleaned
out as required
23 1/2
1/2
Air dam/vent
1 3/4
4 1/2
51
60
4 1/2
Drywall
Backing supplied by others
to meet local codes
12
12
12
12
33"
Access Panel
12
12
Adhesive
Adhesive
FRAME SUPPORT
1. Back edge of Deck may require scribing
to finished wall.
2. Shim all gaps between frame and deck,
especially under trough area.
BASYS DRYER
SPOUT SUBASSEMBLY
HOLDING NUT
ASSEMBLY
CONNECT CONTROL
CABLE TO HAND DRYER
MOTOR
EHD-510
ESD-400
BAYONET TURN
TO LOCK HOSE
TO SPOUT
HOLDING NUT
ASSEMBLY
PROGRAMING
CABLE. LEAVE
UNATTACHED
CONNECT GROUND
WIRE TO HAND
DRYER MOTOR
SOAP DISPENSER
LINES
POWER ADAPTOR
BAYONET TURN
TO LOCK HOSE TO
HAND DRYER MOTOR
SOAP DISPENSER
MOTOR ASSEMBLY
30
Drain clean-outs
Brace
Brace
Fasten frame to
1/8 thick steel
strapping or backing
(not supplied)
22
Backing
21
frame
34
30
Muffler with 2
hand dryer motor hose
Soap
Reservior
33
to top
of frame
Soap
Reservior
Soap
Reservior
OPTIONAL Cold
water supply
OPTIONAL Hot
water supply
NOTES:
1. Mount hand dryer motor & soap dispenser to spec location
2. Slip frame over mounted components & properly
fasten frame to backed wall
3. Hot & Cold water supply lines location subject
to local code
LAVATORY SYSTEM ROUGH-IN PLUMBING & ELECTRICAL DIMENSIONS FRONT VIEW TRIPLE STATION
(3) Hand dryer motor
GFI Receptacle
120V/20AMP
90
Standard 3 x 5
duplex receptacles
per sink manufacturer
requirements
6 5/8
34 33 to
top of
frame
Hand dryer
motor mounting
plate
23
A.F.F.
4 1/4
Soap
Reservior
Soap
Hand dryer
Reservior motor mounting
plate
19
Drains
11 1/2
Cold
water
Hot supply 20
water supplies
water
supply
OPTIONAL Hot
water supply
2 7/8
Hand dryer
Soap
Reserviormotor mounting
plate
Fasten frame to
1/8 thick steel
strapping or backing
material (not supplied)
OPTIONAL Cold
water supply
Finished Floor
NOTES:
1.Hand Dryer Motor alone is only 500 watts or less with speed control
2. Hand Dryer Motor with heater requires 1500 watts or less with speed control
3. Hand Dryer Motor must be plugged into a dedicated 20 amp GFI safety circuit
4. Hand Dryer Motor to have a dedicated circuit with power cord and grounded plug
5. cut backing to allow for electrical and plumbing components
ROUGH-IN PLUMBING & ELECTRICAL
Sloan BASYS
Hand Dryer Spout
(patent applied for)
1/2 Solid surface
1/2 Backing Material
1/4 x 4 Steel plate
Vented basin design
(patent applied for)
Drain box & clean out
(patent applied for)
6 Max.
Optional aluminum
C-Channel w/LEDs
inside tract (120 volt
transformer required)
Stainless steel
34
access door
hangs on
27
rectangular
tubing frame
Push button latches snap
into place inside tubing
Finished Floor
3
1/2
1
Air dam
(patent applied for)
5 1/2
3/4
7 1/4
8 min.
16 1/8
Access
panel
11 1/8
11
6 max.
9
Drywall
17 min.
20 23
Water A.F.F.
Supplies
12 to
19 drain
bottom
14
of frame
to bottom
NOTE:
of Dryer
1. Backing material
Mounting
should equal thickness
Plate
of drywall (1/2 min.)
Hand
Dryer
Motor
21
frame
31
8 1/2
8 1/2
31
6 1/2
Sloan BASYS
Hand Dryer
6 1/2 7 1/2
8 1/2
Sloan BASYS
Mid Faucet
Sloan Foam
Soap Dispensers
5 3/8
3/4
Drain w/clean-out
Grid strainer to be cleaned
out as required
High Point
23 1/2
1 3/4
81
90
4 1/2
4 1/2
Steel/Wood Stud
2x4 or 2x6
(See page 10 for
steel stud installation
requirements)
Drywall
Backing supplied by
others to meet local codes
Hand Dryer Motor
w/ Muffler Attachment
Soap Reservior
Frame
Lag Bolts
Enclosure
12
12
12
12
12
12
6
33
Access
Panels (2)
*Due to manufacturing
tolerances, all dimensions
are for reference only.
12
12
12
Adhesive
BASYS DRYER
SPOUT SUBASSEMBLY
FRAME SUPPORT
1. Back edge of Deck may require scribing
to finished wall.
2. Shim all gaps between frame and deck,
especialy under trough area.
HOLDING NUT
ASSEMBLY
CONNECT CONTROL
CABLE TO HAND DRYER
MOTOR
EHD-510
ESD-400
BAYONET TURN
TO LOCK HOSE
TO SPOUT
HOLDING NUT
ASSEMBLY
PROGRAMING
CABLE. LEAVE
UNATTACHED
CONNECT GROUND
WIRE TO HAND
DRYER MOTOR
SOAP DISPENSER
LINES
POWER ADAPTOR
BAYONET TURN
TO LOCK HOSE TO
HAND DRYER MOTOR
SOAP DISPENSER
MOTOR ASSEMBLY
29
Drain clean-outs
Brace
21 3/4
16 3/8
21
frame
Fasten frame to
1/8 thick steel
strapping or backing
Brace
9 1/4
Soap
Reservior
34
Muffler with 2
hand dryer motor hose
29
9 1/4
20 5/8
22
Backing
33
to top
of frame
Soap
Reservior
Soap
Reservior
Soap
Reservior
16 3/8
LAVATORY SYSTEM ROUGH-IN PLUMBING & ELECTRICAL DIMENSIONS FRONT VIEW QUADRUPLE STATION
(4) Hand dryer
GFI Receptacle
120V/20AMP
Standard 3 x 5duplex
receptacles per sink
manufacturer requirements
7 7/8
34
120
11
Soap
Hand dryer
motor mounting Reservior
plate
8
Soap
Reservior
10 7/8
Soap
Hot
water
supply
23
A.F.F.
Soap
Reservior
Hand Dryer
Hand Dryer
6
Reservior
motor mounting motor mounting
plate
plate
Cold
Hot
water
water supply
supply
20
water
supplies
14
19
Drains
Cold
water
supply
12 3/8
Hand dryer
motor mounting
plate
Fasten frame to
1/8 thick steel
strapping or backing
material (not supplied)
33 to
top of frame
Finished Floor
NOTES:
1. Hand Dryer Motor alone is only 500 watts or less with speed control
2. Hand Dryer Motor with heater requires 1500 watts or less with speed control
3. Hand Dryer Motor must be plugged into a dedicated 20 amp GFI safety circuit
4. Hand Dryer Motor to have a dedicated circuit with power cord and grounded plug
5. cut backing to allow for electrical and plumbing components
ROUGH-IN PLUMBING & ELECTRICAL
Sloan BASYS
Hand Dryer Spout
(patent applied for)
1/2 Solid surface
1/2 Backing Material
1/4 x 4 Steel plate
Vented basin design
(patent applied for)
Drain box & clean out
(patent applied for)
6 Max.
Optional aluminum
C-Channel w/LEDs
inside tract (120 volt
transformer required)
Stainless steel
34
access door
hangs on
27
rectangular
tubing frame
Push button latches snap
into place inside tubing
Finished Floor
3
1/2
1
Air dam
(patent applied for)
5 1/2
3/4
7 1/4
8 min.
16 1/8
Access
panel
11 1/8
11
6 max.
9
Drywall
17 min.
20 23
Water A.F.F.
Supplies
12 to
19 drain
bottom
14
of frame
to bottom
NOTE:
of Dryer
1. Backing material
Mounting
should equal thickness
Plate
of drywall (1/2 min.)
Hand
Dryer
Motor
21
frame
6 1/2 8 1/2
31
31
31
6 1/2
Sloan BASYS
Hand Dryer
Sloan BASYS
Mid Faucet
Sloan Foam
Soap Dispensers
3/4
23 1/2
Drain w/clean-out
Grid strainer to be cleaned
out as required
Drain w/clean-out
Grid strainer to be cleaned
out as required
1 3/4
111
120
4 1/2
4 1/2
Steel/Wood Stud
2x4 or 2x6
(See page 10 for steel
stud installation
requirements)
Drywall
Lag Bolts
Frame Enclosure
12
12
12
12
12
12
12
6
33
Access
Panels (2)
*Due to manufacturing
tolerances, all dimensions
are for reference only.
12
12
12
12
12
12
Adhesive
FRAME SUPPORT
1. Back edge of Deck may require scribing to
finished wall.
2. Shim all gaps between frame and deck,
especialy under trough area.
BASYS DRYER
SPOUT SUBASSEMBLY
HOLDING NUT
ASSEMBLY
CONNECT CONTROL
CABLE TO HAND DRYER
MOTOR
EHD-510
ESD-400
BAYONET TURN
TO LOCK HOSE
TO SPOUT
HOLDING NUT
ASSEMBLY
PROGRAMING
CABLE. LEAVE
UNATTACHED
CONNECT GROUND
WIRE TO HAND
DRYER MOTOR
SOAP DISPENSER
LINES
POWER ADAPTOR
BAYONET TURN
TO LOCK HOSE TO
HAND DRYER MOTOR
SOAP DISPENSER
MOTOR ASSEMBLY
Drywall
5 - 18 gauge
stud reinforcement
between studs
Backing supplied
by others to meet
local codes
Flange
Min.
Gauge
1-3/8
1-5/8
2
2-1/2
1-3/8
1-5/8
2
2-1/2
3
14
16
16
18
18
18
18
18
16
1-3/8
1-5/8
2
2-1/2
1-3/8
1-5/8
2
2-1/2
3
14
16
16
16
16
18
18
18
16
1-3/8
1-5/8
2
2-1/2
1-3/8
1-5/8
2
2-1/2
3
12
16
16
16
16
18
18
18
16
3-5/8
1-3/8
1-5/8
2
2-1/2
14
14
16
16
1-5/8
2
2-1/2
3
16
18
18
16
1-3/8
1-5/8
2
2-1/2
1-5/8
2
2-1/2
3
12
12
16
12
16
18
18
16
1-5/8
2
2-1/2
3
2
2-1/2
3
12
14
16
16
18
18
16
Depth
3-5/8
Sink Length
42"
10
6
2"
Sink System
Enclosure
35"
Drywall
3-5/8
12
6
3-5/8
14
WOOD FRAME MOUNTING SUPPORT
6
Drywall
Backing supplied
by others to meet
local codes
2x10 wood
reinforcement
between studs
16
Sink Length
2'
42"
Sink System
Enclosure
35"
3-5/8
Drywall
18
6
3-5/8
20
6
10
10
2x4
2x6
2
1
12
2x4
2x6
3
1
14
2x4
2x6
3
1
16
2x4
2x6
3
1
18
2x4
2x6
3
1
20
2x4
2x6
3
2
SPF
Grade
No. 2
Depth
3-5/8
10
6
3-5/8
12
6
3-5/8
14
6
3-5/8
16
6
3-5/8
18
6
3-5/8
20
6
Flange
Min.
Gauge
1-3/8
1-5/8
2
2-1/2
1-3/8
1-5/8
2
2-1/2
3
14
16
16
18
18
18
18
18
16
1-3/8
1-5/8
2
2-1/2
1-3/8
1-5/8
2
2-1/2
3
14
16
16
16
16
18
18
18
16
1-3/8
1-5/8
2
2-1/2
1-3/8
1-5/8
2
2-1/2
3
12
16
16
16
16
18
18
18
16
1-3/8
1-5/8
2
2-1/2
1-5/8
2
2-1/2
3
14
14
16
16
16
18
18
16
1-3/8
1-5/8
2
2-1/2
1-5/8
2
2-1/2
3
12
12
16
12
16
18
18
16
1-5/8
2
2-1/2
3
2
2-1/2
3
12
14
16
16
18
18
16
Grade
Stubborn Stains: Remove tough stains, with non abrasive cleaners and
pads such as a white Scotch Brite pad and Lysol. Special Situations for
Corian and Engineered Stone
10
2x4
2x6
3
1
12
2x4
2x6
3
1
Hard Water Deposits: Remove hard water deposits with a mild solution of
vinegar and water. Always rinse the unit thoroughly after cleaning.
14
2x4
2x6
3
1
Restoring the surface: Refresh and restore the rich surface with one of the
following:
16
2x4
2x6
3
2
18
2x4
2x6
3
2
20
2x4
2x6
3
2
SPF
No. 2
BRAND NAMES
Use of brand names is intended only to indicate a type of cleaner. This does
not constitute an endorsement, nor does the omission of any brand name
cleaner imply inadequacy. Many products named are regional in distribution,
and can be found in local supermarkets, department and hardware stores,
or through your cleaning service. It is emphasized that all products should be
used in strict accordance with package instructions.
REGULAR CLEANING OF DRAIN BOX REQUIRED.
DRAIN
GRID STRAINER
DRAIN BOX
4
FINISHED
WALL
3
ACCESS PANEL
FINISHED FLOOR
BOX
11
Deck
Optional
Not Provided
Chrome or
Plastic P-Trap
Grid Strainer
Assembly
DS-57
Mix-60-A
Mix-135-A
Rubber Gasket
Slip Washer
Flange Nut
Enclosure
Basys
Mid Faucet (EFX Series)
Basys
High Faucet (EFX Series)
Basys
Low Integrated Faucet (EFX Series)
Basys
Low Pedestal Faucet (EFX Series)
Basys
Hand Dryer
Basys
Soap Dispenser
Basys
Wall Mount Faucet (EFX Series)
Deck
Grid Strainer
Assembly
DS-57
Mix-60-A
Mix-135-A
Rubber Gasket
Slip Washer
Flange Nut
Enclosure
Basys
Mid Faucet (EFX Series)
Basys
High Faucet (EFX Series)
Basys
Low Integrated Faucet (EFX Series)
Basys
Low Pedestal Faucet (EFX Series)
Basys
Hand Dryer
Basys
Soap Dispenser
Basys
Wall Mount Faucet (EFX Series)
Optional
Not Provided
Chrome or
Plastic P-Trap
Mix-60-A
Mix-135-A
Rubber Gasket
Slip Washer
Flange Nut
Enclosure
Basys
High Faucet (EFX Series)
Basys
Mid Faucet (EFX Series)
Basys
Low Pedestal Faucet (EFX Series)
Basys
Soap Dispenser
Basys
Wall Mount Faucet (EFX Series)
Basys
Low Integrated Faucet (EFX Series)
Basys
Hand Dryer
Deck
Optional
Not Provided
Chrome or
Plastic P-Trap
Mix-60-A
Mix-135-A
Rubber Gasket
Slip Washer
Flange Nut
Enclosure
Basys
High Faucet (EFX Series)
Basys
Low Integrated Faucet (EFX Series)
12
Basys
Mid Faucet (EFX Series)
Basys
Low Pedestal Faucet (EFX Series)
Basys
Wall Mount Faucet (EFX Series)
Basys
Hand Dryer
Basys
Soap Dispenser