Академический Документы
Профессиональный Документы
Культура Документы
Page 1 of 23
SUBJECT
REVISION
PREPARED BY:
DATE
V 1.0
Gilbert T. Lacanlale
Scenario/Condition 1:
We have an existing tunnel (Source site to Middle Site and Middle site to Destination site).
Where middle site is L2 Core Layer Router.
We have an existing TD-LTE service.
We will be adding a node to this existing service
Example given is Work order WO_14-3536. C24_BAGUIO3 Slot 9port 8 face to 3835 SFLU Slot
14 port 2. Vlan 2769,2969 and 2869.
CONFIDETIAL
Page 2 of 23
SUBJECT
REVISION
PREPARED BY:
DATE
V 1.0
Gilbert T. Lacanlale
CONFIDETIAL
Page 3 of 23
SUBJECT
REVISION
PREPARED BY:
DATE
V 1.0
Gilbert T. Lacanlale
CONFIDETIAL
Page 4 of 23
SUBJECT
REVISION
PREPARED BY:
DATE
V 1.0
Gilbert T. Lacanlale
NOTE:
Under General Info:
select port ratetype= GE
port_desc add word order name and the date.
Under Physical property
select operating_mode=Full_Duplex
Select photovoltaic_mode=Electric_port
5. Right click and choose "Add", choose the port to be used(on Main Interface) and add the
vlan(vlan 2769,2969 and 2869).
CONFIDETIAL
Page 5 of 23
SUBJECT
REVISION
PREPARED BY:
DATE
V 1.0
Gilbert T. Lacanlale
CONFIDETIAL
Page 6 of 23
SUBJECT
REVISION
PREPARED BY:
DATE
V 1.0
Gilbert T. Lacanlale
7. Wait for ~10 seconds for all the data to be loaded. Under All Circuits Tab, search the
source site for available tunnel, select the specific tunnel (tunnel must be a dynamic tunnel
and must be from source site to middle site).
CONFIDETIAL
Page 7 of 23
SUBJECT
REVISION
PREPARED BY:
DATE
V 1.0
Gilbert T. Lacanlale
10. Select the tunnel that carries the VC that you are creating(Source to Middle site). On Batch
Creation settings, you can set the number of VC that you want to created. On the example
given, we need 3 VCs as we have 3 VLANS. On Lot size, write 3.
CONFIDETIAL
Page 8 of 23
SUBJECT
REVISION
PREPARED BY:
DATE
V 1.0
Gilbert T. Lacanlale
12. Under Business Management View, Find the existing TD-LTE service under the PTN
Ethernet Service. Search the Fination site(on our example, it is SFLU(3835 ID).
CONFIDETIAL
Page 9 of 23
SUBJECT
REVISION
PREPARED BY:
DATE
V 1.0
Gilbert T. Lacanlale
14. Find the Destination site port(on our example, the LTE service will be via 3835 s14p2)
service. Make sure that the Destination ports VLAN will be the same VLAN that you will
used based on your Work Order.
15. Right click the chosen E-LAN, choose modify and choose Add Node .
CONFIDETIAL
Page 10 of 23
SUBJECT
REVISION
PREPARED BY:
DATE
V 1.0
Gilbert T. Lacanlale
16. Click the source node and choose the port to be used(on our example, it is s9p8). We have
created 3 VLANS for the Source site so make sure you select the right VLAN which is the
same VLAN with your Destination Port.
17. Click next. Then Choose the Source site and the middle site Tunnel.
CONFIDETIAL
Page 11 of 23
SUBJECT
REVISION
PREPARED BY:
DATE
V 1.0
Gilbert T. Lacanlale
19. Click NEXT. Modify the Source site UNI Interface: Split Horizon = Enable and NNI
interface: Split Horizon = Disable.
CONFIDETIAL
Page 12 of 23
SUBJECT
REVISION
PREPARED BY:
DATE
V 1.0
Gilbert T. Lacanlale
20. Click Complete . After successfull creation. Click cancel before delivering the Cross
connection.
21. Right Click the E-LAN with the Partly Active Status and select " Deliver Cross-connect of
the selected path".
CONFIDETIAL
Page 13 of 23
SUBJECT
REVISION
PREPARED BY:
DATE
V 1.0
Gilbert T. Lacanlale
Scenario/Condition 2:
1. Configure the slot/port /VLAN on source and destination site via Ethernet Interface.
2. Create a dynamic tunnel
Tunnel to be created is two: Source to Middle site and Destination to Middle site
Example given below is tunnel creation from a source to destination, in our scenario, we need to
create 2 tunnels-Source to Middle Site and Middle Site to Destination.
Example of Tunnel Creation(Source to Destination)
In Business Management View, go to Service Configuration > IP Config >Tunnel Config
CONFIDETIAL
Page 14 of 23
SUBJECT
REVISION
PREPARED BY:
DATE
V 1.0
Gilbert T. Lacanlale
a. Click Source LSR and select the source site on the topology, Click the Sink LSR and
check the destination site on the topology. Check Enable BFD(Bidirectional Forwarding
Detection).
CONFIDETIAL
Page 15 of 23
SUBJECT
c.
REVISION
PREPARED BY:
DATE
V 1.0
Gilbert T. Lacanlale
Click the line interconnecting the source site and its next hop router, a box will pop-up
where you will tick the site corresponding to the next hop router until it reaches the
destination.
CONFIDETIAL
Page 16 of 23
SUBJECT
REVISION
PREPARED BY:
DATE
V 1.0
Gilbert T. Lacanlale
e. Under Path 1/Path 2 BFD Properties, Select 10ms for the minimum transmit and
received time.
f. We previously configure Source-Dest and Dest Source link. This is now your main
route. Configure again and repeat steps 8 to 11 for the protection route.
Note: Example given is Source-Destination Tunnel, please create Source-Mid and MidDestination Tunnel according to planning. This is just an example.
g. We need to add LDP protocol to our link every new tunnel creation. Add LDP protocol
mutually.
Add O93 site manager port/management IP to N19 LDP protocol
To view the sites Manager Port IP, Open O93 mananger port(Interface Manager<> Manager
Port),check its Prim IP :10.112.136.27.
CONFIDETIAL
Page 17 of 23
SUBJECT
REVISION
PREPARED BY:
DATE
V 1.0
Gilbert T. Lacanlale
Open N19 LDP protocol(NE Config> Protocol config> LDP) ,Click LDP_Item Peer, Right
click on the blank space, then click add.
Manually the the O93 Manager Port IP on N19 LDP Protocol Config. Exit on the LDP Item
Peer. Right Click at the created LDP Protocol Item and Click Save Selected to Device.
CONFIDETIAL
Page 18 of 23
SUBJECT
REVISION
PREPARED BY:
DATE
V 1.0
Gilbert T. Lacanlale
CONFIDETIAL
Page 19 of 23
SUBJECT
REVISION
PREPARED BY:
DATE
V 1.0
Gilbert T. Lacanlale
3.
4.
a.
b.
No need to create VC
Create the service
Service configuration >> IP config >> L2VPN
Choose ELAN
Write the site ID slotport and vlan number
Next
c. Choose the destination site FIRST, choose its port, then click Middle site(choose all) and
the Source site will be the LAST, Next
d. Click 2 tunnels that you created or is available, first the dest-mid tunnel and the mid-source
tunnel.
e. Click 2 VC, source to mid and mid to destination VC. Choose dynamic VC.
0 means dynamic vc
304 , 311 or 312 means static vc
f. After clicking next, You will see tabs
Dest/Mid/Source
On destination site tab,
UNI: cross connect mode must be VPLS
NNI-enable
Middle site tab
NNI:
Source to middle site
Split horizon enable
Mid to destination
Split horizon disable
CONFIDETIAL
Page 20 of 23
SUBJECT
REVISION
PREPARED BY:
DATE
V 1.0
Gilbert T. Lacanlale
CONFIDETIAL
Page 21 of 23
SUBJECT
REVISION
PREPARED BY:
DATE
V 1.0
Gilbert T. Lacanlale
CONFIDETIAL
Page 22 of 23
SUBJECT
REVISION
PREPARED BY:
DATE
V 1.0
Gilbert T. Lacanlale
Scenario/Condition 3:
CONFIDETIAL
Page 23 of 23
SUBJECT
REVISION
PREPARED BY:
DATE
V 1.0
Gilbert T. Lacanlale