E000 - Heater temperature fault (bug heat roller) E001 - Overheating detection error (detected overheating) E002 - Heater temperature error (insufficient heating temperature of the shaft) E003 - Heater temperature error (temperature drop of the heat roller) E007 - Fixing film rotation error (the error of rotation oven) E010 - Main motor rotation error (the error of the main engine) E014 - Fixing motor rotation error (bug engine heaters) E019 - Waste toner case full, sensor error (container filled with waste toner) E032 - DA unit communication error (error svyazis block DA) E051 - Horizontal registration HP detention error (bug horizontal registration HP) E064 - Power supply voltage error (error voltage) E100 - Laser BD error (the error of the laser) E110 - Polygon motor rotation error (the error of polygonal motor) E202 - No.1 mirror base HP detecting error (an error is detected mirrors No.1) E204 - ADF image leading edge signal detection fault (fault ADF) E220 - Lamp ON error (error lamp is switched on) E225 - Standard white plate / edge white plate read error (error reading the white border) E240 - Mcon-Dcon communication error (communication error Mcon-Dcon) E243 - Mcon-control panel communication error (communication error Control Panel Mcon) E248 - Backup (EEPROM) error (backup error EEPROM) E261 - Zero-cross signal error E302 - Shading error (error shadowing) E315 - Image data processing error (an error processing the image data) E601 - Image transfer error (error image transmission) E602 - Hard disk error (hard disk error) E604 - Image memory fault (fault memory image) E605 - Image memory battery fault (battery fault memory image) E606 - HDD error (error HDD) E674 - Fax board error (error on fax) E677 - PDL board mounting error (bug shield PDL) E710 - IPC initialization error (Error initializing IPC) E711 - IPC register error (sampling error IPC) E712 - Communication error with ADF (communication error with ADF) E713 - Communication error with sorter finisher (error due to the sorter) E716 - Communication error with pedestal (communication error with stand) E717 - Communication error with ASSIST (communication error with the ASSIST) E719 - Card reader, coin vendor communication error (error due to the card reader) E732 - Reader communication error E733 - Printer communication error (the error of the printer) E737 - SDRAM error (error SDRAM) E740 - Ethernet board error (error on Ethernet) E741 - PCI bus error (bus error PCI) E742 - RIP1 board error (error on RIP1) E743 - Mcon-Rcon communication error (communication error Mcon-Rcon) E803 - MPWS power supply voltage error (error voltage MPWS) E805 - Fan rotation error (the error of the fan) E901 - Pedestal main motor rotation error [ADF] (error of rotation of the main motor ADF)
E420 - Back-up data read error (error reading backup data)
E421 - Back-up data write error (error writing backup data) E422 - IPC error (error IPC) E501 - Communication error Punch unit (communication error module perforation) E505 - Back-up RAM (backup RAM) E510 - Feed motor (motor supply) E514 - Delivery motor (engine delivery) E530 - Width plate shift motor E531 - Stapler motor E532 - Stapler slide motor E537 - Alignment motor (motor alignment) E540 - Tray ascent / descent motor (motor tray ascent / descent) E577 - Paddle motor E590 - Puncher motor (motor perforation) E592 - Puncher sensor error (sensor error perforation) E593 - Puncher shift motor (motor punching shear) E5F1 - Saddle folder motor E500 - Communication error (communication error) E514 - Stack handling motor (motor processing) E530 - Rear alignment motor (electric rear leveling) E531 - Stapler motor E537 - Front alignment motor (front engine vyrpvnivaniya) E577 - Delivery motor (engine delivery) E580 - Delivery tray ascent / descent motor (motor output tray) E585 - Stack handling error (an error processing stack) Bi vit cng ch
Sayon Dutta - Reinforcement Learning With TensorFlow - A Beginner's Guide To Designing Self-Learning Systems With TensorFlow and OpenAI Gym-Packt Publishing (2018)