Академический Документы
Профессиональный Документы
Культура Документы
2/1
Environmental Chemistry II
Cu(NO3)2.3H2O (FW 241.58) will be used to prepare your copper stock solution.
How much will you need to make up 250 ml of stock solution containing 250
g/ml (= 250 ppm) of copper?
2.
Your stock solution will be diluted to prepare standard solutions for calibration of
the photometer. Calculate the volumes of 250 g/ml stock solution required to
prepare 50 ml each of solutions with concentrations of 5, 10, 15, 20 and 25 g/ml.
3.
Arsenious oxide, As2O3, was used to prepare the arsenic stock solution. Using
the Material Safety Data Sheet for As2O3, list all hazards associated with and
precautions that should be taken when using this compound. What first aid
measures should be taken in the event of contact?
Introduction
Chemicals or mixtures of chemicals have long been used to treat wood in an effort to
extend the lifetime of the wood under conditions which would normally accelerate
deterioration. Examples of treated wood include fence posts, plywood used for wood
foundations and permapine used to build children's playgrounds.
In recent years, wood has been pressure treated with a green-coloured aqueous solution
containing copper, chromium and arsenic. This compound, known as "copper
chromated arsenic" is toxic to insects, bacteria and small mammals and also retards the
growth of mildew and fungus. The drawback to this treatment is that it can slowly
leach out of treated lumber due to its water solubility. Copper, arsenic and chromium
can also get into groundwater if spent solutions used to treat lumber are improperly
disposed of. In addition, burning wood treated with this substance can contaminate a
large area around the burn site with toxic metal compounds.
The purpose of this experiment is to use atomic absorption spectrophotometry to
determine the amount of copper and arsenic in a sample of copper chromated arsenictreated wood.
Atomic line absorption spectra are used for analysing various metals. Atomic
absorption spectrophotometry ("AA") offers sensitivity, selectivity and simplicity and
was developed by CSIRO Melbourne scientists around 1955. "AA" is an important tool
in analytical laboratories.
13/02/2004
11:43 AM
C:\Expts\Environm\As-Cu-AA.Doc
Experiment 2
2/2
Environmental Chemistry II
Experimental
Note: do not dispose of any solutions before reading the section on waste disposal at
the end of the experimental section.
Extraction with Nitric Acid
Carry out this procedure on two samples so that duplicate results may be obtained and
averaged.
Weigh accurately into a 150 ml beaker (to the nearest 0.1 mg) approximately 1 g of
small particles from a pressure treated wood sample. Add 50 ml of 4M nitric acid,
cover the beaker with a watch glass. Leave on the steambath (fumehood) for 20
minutes, keeping a close watch on the samples to ensure they do not froth over.
Allow the two samples to cool. Filter off any insoluble material using vacuum filtration
with a buchner funnel. Rinse the beaker and the watch glass four times each with
portions of deionised water, each time pouring the rinse water through the funnel so that
it is added to the 50 ml of filtrate. Transfer the filtrate combined with rinses to a clean
250 ml volumetric flask and make up to the mark with deionised water. Ensure
thorough mixing by inverting the flask at least ten times.
Preparation of standard solutions
AA is very sensitive and low concentrations are used, so all glassware must be clean!
Wash well with hot tap water then rinse thoroughly with deionised water.
A 250 g/ml arsenic stock solution has been provided for you, but you must prepare the
250 g/ml copper stock solution (250 ml) yourself (preliminary question 1). Ensure
thorough mixing by inverting the flask at least ten times.
The standard solutions you will prepare will contain both copper and arsenic.
Concentrations of both metals in the standards are to be 0, 5, 10, 15, 20 and 25 g/ml.
Prepare the blank solution (0 g/ml) by adding 20 ml of 4M nitric acid to a 50 ml
volumetric flask and making up to the mark with deionised water. Prepare the other
standard solutions in a similar way by diluting the required amount of each stock
solution (preliminary question 2 - the volumes you calculated for the copper stock
solution will be the same required for the arsenic stock solution) plus 20 ml of 4M of
nitric acid to 50 ml. Once again, ensure thorough mixing by inverting each flask at
leask ten times. Don't forget that a "5 g/ml standard solution" will contain 5 g/ml of
both copper and arsenic.
13/02/2004
11:43 AM
C:\Expts\Environm\As-Cu-AA.Doc
Experiment 2
2/3
Environmental Chemistry II
Calculate the amounts of copper and arsenic present per gram of treated wood
(NB - results for the two samples should not be averaged until an amount of metal
per gram of wood for each sample has been calculated).
2.
Consider sources of error which may have caused your final calculated amounts
of copper and arsenic to be incorrect.
3.
Did the concentrations of copper and arsenic in the two samples match closely
(within 0.5 ppm)? If not, give a possible reason for this. (Hint: consider probable
sampling techniques for the treated wood sample and the manner in which the
wood may be treated.)
13/02/2004
11:43 AM
C:\Expts\Environm\As-Cu-AA.Doc
Experiment 2
2/4
Environmental Chemistry II
Report
Your report should contain the following:
quantities (weights and volumes) used to make up the stock solution and the
standard solutions containing both copper and arsenic - use table form wherever
possible
calculations showing how the amounts of copper and arsenic per gram of wood
were calculated
answers to questions
Reference
1.
13/02/2004
11:43 AM
C:\Expts\Environm\As-Cu-AA.Doc