Академический Документы
Профессиональный Документы
Культура Документы
LCD MODULE
CUSTOMER
CUSTOMER PART NO.
AMPIRE PART NO.
AM-1024768J1TRQW-00
APPROVED BY
DATE
Approved For Specifications
Approved For Specifications & Sample
A )
116 4 (
TEL:886-2-26967269 , FAX:886-2-26967196 or 26967270
APPROVED BY
Date : 2012/8/29
CHECKED BY
ORGANIZED BY
RECORD OF REVISION
Revision Date Page
2012/8/29
Date : 2012/8/29
--
Contents
New Release
Editor
Kokai
1. Features
8 inch Amorphous-TFT-LCD (Thin Film Transistor Liquid Crystal Display) module.
This module is composed of a 8 TFT-LCD panel and LED backlight.
(1) Construction: 8 a-Si TFT active matrix, White LED Backlight.
(2) Resolution (pixel): 1024(R.G.B) X768
(3) LCD type : Transmissive , normally White
(4) Interface: LVDS interface 6bit / 8bit selectable by H/W pin setting.
(5) Viewing Direction: 4:30 Oclock ( The direction its hard to be discolored )
2. PHYSICAL SPECIFICATIONS
Item
LCD size
Resolution
Specifications
unit
8 inch (Diagonal)
1024 x 3(RGB) x 768
dot
Dot pitch
0.05275(W) x 0.15825(H)
mm
Active area
162.048(W) x 121.536(H)
mm
Module size
mm
Surface treatment
Color arrangement
RGB-stripe
Interface
Brightness
Weight
Date : 2012/8/29
LVDS
250 (Typ.)
cd/m2
T.B.D
Symbol
VCC
UNIT
Min.
Max.
-0.3
5.0
Note
V
AVDD
6.5
13.5
VGH
-0.3
42.0
VGL
-20
0.3
VGH+VGL
40.0
Operation temperature
TOP
-10
50
Storage temperature
TST
-20
60
VR
--
(5)
Each LED
Note 2
IF
--
(30)
mA
Each LED
Power voltage
Note 1: The absolute maximum rating values of this product are not allowed to be
exceeded at any times. Should a module be used with any of the absolute maximum
ratings exceeded, the characteristics of the module may not be recovered, or in an
extreme case, the module may be permanently destroyed.
Note 2: VR Conditions: Zener Diode 20m
Date : 2012/8/29
4. ELECTRICAL CHARACTERISTICS
4-1 Typical Operation Conditions
Item
Values
Symbol
Unit
Remark
3.6
Note 2
11.5
11.7
21.7
22
22.3
VGL
-7.3
-7
-6.7
VCOM
2.3
(3.3)
4.3
MIN
TYP
MAX
VCC
3.0
3.3
AVDD
11.3
VGH
Power Voltage
Logic input
VCC
V
VIH
0.7VCC
high voltage
Logic input
VIL
GND
0.3VCC
V
low voltage
Note 1: Be sure to apply VCC and VGL to the LCD first, and then apply VGH.
Logic
Input
Voltage
Note 3
Note 4
Note 4
Note 2: VCC setting should match the signals output voltage (refer to Note 3) of
customers system board .
Note 3 Typical VCOM is only a reference value. It must be optimized according to
each LCM. Please use VR and base on below application circuit.
Note 4: RESET,STBYB,SELB,L/R,U/D,CABCEN0,CABCEN1.
AVDD
15K
0.1uF/50V
VR1
VCOM
10K
10uF/16V
0.1uF/50V
6.8K
Date : 2012/8/29
Values
Symbol
Unit
Remark
(60)
mA
VCC=3.3V
(20)
(30)
mA
AVDD=11.5V
--
(0.35)
(1.0)
mA
VGH=22V
--
(0.35)
(1.0)
mA
VGL=-7V
Unit
Remark
Note 1
MIN
TYP
MAX
ICC
(40)
IAVDD
IGH
IGL
Values
Symbol
MIN
TYP
MAX
VL
8.4
9.3
10.2
IL
(170)
180
(190)
mA
--
20,000
--
--
Hr
Note 2
Note 1: The LED Supply Voltage is defined by the number of LED at Ta=25 and
Allowable Forward Current IF (mA)
IL =180mA.
180
160
140
120
-20 -10
10 20 30 40 50 60 70
Note 2: The LED life time is defined as the module brightness decrease to 50%
original brightness at Ta=25 and IL =180mA. The LED lifetime could be decreased
if operating IL is lager than 180 mA.
Date : 2012/8/29
VDD
<500uS
STBYB
>50uS
>500uS
RESET
LVDS
Signal
>35mS
Normal Signal
<20mS
AVDD
VCOM
VGL
>20uS
>40uS
VGH
>120mS
B/L
Date : 2012/8/29
Power Off
Date : 2012/8/29
5. Optical Specifications
Values
Item
Symbol
Condition
Min.
Typ.
Max.
Unit
Note
degree
Note1
= 180
(9 oclock)
65
75
--
= 0
(3 oclock)
65
75
--
= 90
(12 oclock)
65
75
--
= 270
(6 oclock)
65
75
--
TON
--
10
12
msec
TOFF
--
15
28
msec
CR
600
700
--
--
0.26
0.31
0.36
--
WY
0.28
0.33
0.38
--
Luminance
200
250
--
cd/m2
Note6
Luminance
uniformity
YU
70
75
--
Note7
Viewing angle
(CR10)
Note3
Response time
Contrast ratio
Color
chromaticity
WX
Normal
==0
Note4
Note5
Note6
Test Conditions:
1. VCC = 3.3V, IL = 180mA (Backlight current), the ambient temperature is
25.
2. The test systems refer to Note 2.
Date : 2012/8/29
Date : 2012/8/29
10
Date : 2012/8/29
11
Bmax
W ----- Active area width
Date : 2012/8/29
12
6. INTERFACE
TFT LCD Panel Driving Section
Pin No.
Symbol
I/O
Description
VCOM
Common Voltage
VDD
VDD
NC
--
No connection
RESET
STBYB
GND
Ground
RXIN0-
RXIN0+
10
GND
Ground
11
RXIN1-
12
RXIN1+
13
GND
Ground
14
RXIN2-
15
RXIN2+
16
GND
Ground
17
RXCLKIN-
18
RXCLKIN+
19
GND
Ground
20
RXIN3-
21
RXIN3+
22
GND
Ground
23
NC
--
No connection
24
NC
--
No connection
Date : 2012/8/29
Note
13
Pin No.
Symbol
I/O
Description
Note
25
GND
Ground
26
NC
--
No connection
27
DIMO
28
SELB
29
AVDD
30
GND
Ground
31
LED-
LED Cathode
32
LED-
LED Cathode
33
L/R
Horizontal inversion
Note3
34
U/D
Vertical inversion
Note3
35
VGL
36
CABCEN1
Note2
37
CABCEN0
Note2
39
LED+
LED Anode
40
LED+
LED Anode
Note1
Date : 2012/8/29
14
Up
Left
Right
Down
Date : 2012/8/29
15
7. TIMING CHARACTERISTICS
7-1 AC Electrical Characteristics
Parameter
Values
Symbol
Unit
MIN
TYP
MAX
Clock frequency
RxFCLK
20
--
71
TRSKM
500
--
--
TLVCH
--
4/(7* RxFCLK)
--
TLVCL
--
3/(7* RxFCLK)
--
Date : 2012/8/29
Remark
16
Symbol
Unit
Min.
Typ.
Max.
RxVTH
+0.1
RxVTH
-0.1
RxVIN
2.4
RxVCM
|VID|/2
2.4-|VID|/2
Differential voltage
|VID|
0.2
0.6
Differential input
leakage current
RVxliz
-10
+10
uA
Differential input
high Threshold
voltage
Differential input low
Threshold voltage
Input voltage range
(singled-end)
Differential input
common mode
voltage
Date : 2012/8/29
Note
RXVCM=1.2
V
17
7-3 Timing
Values
Item
Symbol
Min.
Typ.
Max.
52
65
71
Unit
Note
MHz
Frame rate
=60Hz
Clock Frequency
fclk
Horizontal display
area
thd
HS period time
th
1114
1344
1400
DCLK
HS Blanking
thb
90
320
376
DCLK
tvd
VS period time
tv
778
806
845
thb
10
38
77
VS Blanking
Date : 2012/8/29
1024
DCLK
768
18
Date : 2012/8/29
19
Test Conditions
Note
Ta = 60 240 hrs
Note 1,4
Note 1,4
Ts = 50 240 hrs
Note 2,4
Note1,4
Thermal Shock
Vibration Test
Mechanical Shock
Random Vibration :
0.015G*G/Hz from 5-200HZ, -6dB/Octave
from 200-500Hz
2 hours for each direction of X. Y. Z.
(6 hours for total)
Height : 60 cm
1 comer, 3 edges, 6 surfaces
2KV, Human Body Mode, 100pF/1500
Date : 2012/8/29
20
9. General Precautions
9-1
Safety
Liquid crystal is poisonous. Do not put it your month. If liquid crystal touches
your skin or clothes, wash it off immediately by using soap and water.
9-2
Handling
1. The LCD panel is plate glass. Do not subject the panel to mechanical
shock or to excessive force on its surface.
2. The polarizer attached to the display is easily damaged. Please handle it
carefully to avoid scratch or other damages.
3. To avoid contamination on the display surface, do not touch the module
surface with bare hands.
4. Keep a space so that the LCD panels do not touch other components.
5. Put cover board such as acrylic board on the surface of LCD panel to
protect panel from damages.
6. Transparent electrodes may be disconnected if you use the LCD panel
under environmental conditions where the condensation of dew occurs.
7. Do not leave module in direct sunlight to avoid malfunction of the ICs.
9-3
Static Electricity
1. Be sure to ground module before turning on power or operation module.
2. Do not apply voltage which exceeds the absolute maximum rating value.
9-4
Storage
1. Store the module in a dark room where must keep at +2510 and
65%RH or less.
2. Do not store the module in surroundings containing organic solvent or
corrosive gas.
3. Store the module in an anti-electrostatic container or bag.
9-5
Cleaning
1. Do not wipe the polarizer with dry cloth. It might cause scratch.
2. Only use a soft sloth with IPA to wipe the polarizer, other chemicals might
permanent damage to the polarizer.
9-5
Others
1. AMIPRE will provide one year warrantee for all products and three months
warrantee for all repairing products.
Date : 2012/8/29
21
Date : 2012/8/29
22
Date : 2012/8/29
23