Академический Документы
Профессиональный Документы
Культура Документы
New Information
Description
Page
1. Introduction . . . . . . . . . . . . . . . . . . . . . .
2. Receiving, Handling, and Storage . . . . . . .
3. Equipment Description . . . . . . . . . . . . . . .
4. Installation and Wiring . . . . . . . . . . . . . . .
5. Functional Testing . . . . . . . . . . . . . . . . . .
6. Adjustments . . . . . . . . . . . . . . . . . . . . . .
7. Maintenance and Component Replacement.
IB70-8671
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
2
5
5
7
11
12
13
Instructional Booklet
Page 2
SECTION 1: INTRODUCTION
WARNING
READ AND UNDERSTAND THE INSTRUCTIONS CONTAINED HEREINAFTER BEFORE ATTEMPTING TO UNPACK, ASSEMBLE, OPERATE,
OR MAINTAIN THIS EQUIPMENT.
HAZARDOUS VOLTAGES ARE PRESENT INSIDE TRANSFER SWITCH
ENCLOSURES THAT CAN CAUSE DEATH OR SEVERE PERSONAL
INJURY. FOLLOW PROPER INSTALLATION, OPERATION, AND MAINTENANCE PROCEDURES TO AVOID THESE VOLTAGES.
THE TRANSFER SWITCH EQUIPMENT COVERED BY THIS INSTRUCTION BOOK IS DESIGNED AND TESTED TO OPERATE WITHIN ITS
NAMEPLATE RATINGS. OPERATION OUTSIDE OF THESE RATINGS
MAY CAUSE THE EQUIPMENT TO FAIL RESULTING IN DEATH, SERIOUS BODILY INJURY, AND/OR PROPERTY DAMAGE. ALL RESPONSIBLE PERSONNEL SHOULD LOCATE THE DOOR MOUNTED
EQUIPMENT NAMEPLATE AND BE FAMILIAR WITH THE INFORMATION PROVIDED ON THE NAMEPLATE. A TYPICAL EQUIPMENT
NAMEPLATE IS SHOWN IN FIGURE 1.
.
L050412234
Cat No: EGS100L24R
Style No:
GO No: ABC0123
Volts: 240
Poles: 2
Amps: 100
Phase: 1
ENCL TYPE: 3R
ITEM: 001
PIECE: 001
OF: 001
Hertz: 60
Wire: 3
30-43465
WARNING
THE WARNINGS AND CAUTIONS INCLUDED AS PART OF THE PROCEDURAL STEPS IN THIS DOCUMENT ARE FOR PERSONAL SAFETY
AND PROTECTION OF EQUIPMENT FROM DAMAGE. AN EXAMPLE
OF A TYPICAL WARNING LABEL HEADING IS SHOWN ABOVE TO
FAMILIARIZE PERSONNEL WITH THE STYLE OF PRESENTATION.
THIS WILL HELP TO ENSURE THAT PERSONNEL ARE ALERT TO
WARNINGS, WHICH APPEAR THROUGHOUT THE DOCUMENT. IN
ADDITION, CAUTIONS ARE ALL UPPER CASE AND BOLDFACE.
CAUTION
READ AND UNDERSTAND THE MATERIAL PRESENTED IN THIS DOCUMENT BEFORE ATTEMPTING INSTALLATION, APPLICATION, OPERATION, OR MAINTENANCE OF THE EQUIPMENT. IN ADDITION,
ONLY QUALIFIED PERSONS SHOULD BE PERMITTED TO PERFORM
ANY WORK ASSOCIATED WITH THE EQUIPMENT. ANY WIRING
INSTRUCTIONS PRESENTED IN THIS DOCUMENT MUST BE FOLLOWED PRECISELY. FAILURE TO DO SO COULD CAUSE PERMANENT EQUIPMENT DAMAGE.
IB70-8671
Instructional Booklet
Effective: July 2008
Page 3
WARNING
Generator
Utility
Load
Figure 2. Typical Load Transfer Switch (Contactor) Schematic.
An intelligence system initiates the transfer when the utility power
source fails or falls below a preset voltage. An engine start is
then initiated by the generator and the ATS transfers to the generator power source when sufficient generator voltage is available.
When the utility power source is restored, the ATS automatically
transfers back and the generator will shut down after a time delay.
In the event the utility power source fails and the generator
power source does not appear, the ATS remains connected to the
utility power source until the generator power source does appear.
Conversely, if connected to the generator power source and the
generator power source fails while the utility power source is still
unavailable, the ATS remains connected to the generator power
source.
ATSs automatically perform the transfer function, and include
three basic elements.
1. Main contacts to connect and disconnect the load to and from
the source of power.
2. Solenoids to make the transfer of the main contacts from
source to source.
3. Intelligence/supervisory circuits to constantly monitor the condition of the power sources and thus provide the intelligence
necessary for the switch and related circuit operation.
IB70-8671
Instructional Booklet
Page 4
100
Eaton
Generator
Switch
100 = 100 A
L 24
Re-Transfer
Re-transfer is defined as a change of the load connection from the
Generator to the Utility.
Loadcenter
Enclosure Type
L24 - 24 Circuit
R = Type 3R
Utility
Utility is the primary source (normal source, normal power source,
or normal).
Generator
Generator is the secondary source (generator emergency source,
emergency power source, emergency, standby, or backup
source).
Utility: Failed or Fails
Utility is defined as failed when it is outside of its undervoltage
setpoint ranges for the nominal voltage and frequency setting.
1.5 Glossary
Transfer
Transfer is defined as a change of the load connection from the
Utility to the Generator power source.
With respect to their use within this document and as they relate
to transfer switch and controller operation, the following terminology is defined.
Unconnected
Unconnected is defined as when the input is not shorted by an
external contact or connection.
Available
A source is defined as available when it is within its undervoltage setpoint ranges for the nominal voltage setting.
Connected
Connected is defined as when the input is shorted by an external
contact or connection.
Failed or Fails
A source is defined as failed when it is outside of the applicable
voltage setpoint ranges for the nominal voltage and for a time
exceeding 0.5 seconds after the time delay emergency fail (TDEF)
time delays expires.
Failsafe
Failsafe is a feature that prevents disconnection from the only
available power source and also forces a transfer or re-transfer
operation to the only available power source.
IB70-8671
Instructional Booklet
Effective: July 2008
Page 5
2.1 Receiving
3.1 Introduction
This ATS monitors both utility and generator power sources and
automatically transfers critical load circuits between the two
sources, depending on which source is available. The utility
power source is preferred and will remain connected to the switch
if it is available.
A shipping label affixed to the shipping container includes a variety of equipment and customer information, such as General
Order and catalog numbers. Make certain that this information
matches the other shipping paper information.
Each ATS enclosure is packaged in its own box. Do not discard
the packing material until the equipment is ready for installation.
Once the packaging is removed from the shipment, the enclosure
door can be opened. A plastic bag of documents will be found in
the enclosure. Important documents, such as wiring diagrams and
appropriate instruction leaflets are enclosed within the bag and
should be filed in a safe place.
2.2 Handling
As previously mentioned, ATS equipment is packaged in its own
box. Protect the equipment from impact at all times and do not
double stack. Once the equipment is at the installation site and
ready to be installed, the packaging material can be removed.
Refer to Section 4 of this manual for specific installation instructions.
2.3 Storage
Although well packaged, this equipment is not suitable for outdoor
storage. The equipment warranty will not be applicable if there is
evidence of outdoor storage. If the equipment is to be stored
indoors for any period of time, it should be stored with its protective packaging material in place. Protect the equipment at all
times from excessive moisture, construction dirt, corrosive conditions, and other contaminants. It is strongly suggested that the
package-protected equipment be stored in a climate-controlled
environment of -20 to 70C (-4 to 158F), with a relative humidity of 80% or less. Do not, under any circumstance, stack other
equipment on top of an ATS equipment enclosure, whether packaged or not.
Main Contacts
IB70-8671
Instructional Booklet
Page 6
3.
The RTC-50 is a microprocessor-based transfer switch logic control package. The hardware and software of the controller contain
the intelligence/supervisory circuits that constantly monitor the
condition of the power sources. It provides the intelligence necessary for the operation of the ATS (Figure 5).
Fixed at 10 Seconds.
5.
26.
Undervoltage:
Dropout: 70% of nominal
Pickup: 80% of nominal
IB70-8671
Instructional Booklet
Effective: July 2008
Page 7
WARNING
BE CERTAIN THAT THE DEADFRONT IS PROPERLY INSTALLED
BEFORE THE TRANSFER SWITCH EQUIPMENT IS PUT INTO SERVICE. THE DEADFRONT PROVIDES PROTECTION FROM DANGEROUS VOLTAGES AT THE LINE AND LOAD TERMINALS WHEN THE
EQUIPMENT IS IN OPERATION. FAILURE TO DO SO COULD RESULT
IN PERSONAL INJURY OR DEATH.
5.321
Choose a location that offers a flat, rigid mounting surface capable of supporting the weight of the enclosed ATS equipment (see
Figure 6). Protect the transfer switch at all times against excessive moisture, dust, dirt, lint, and corrosive vapors.
7.154
5.321
2.633
2.496
14.462
5.198
19.005
29.332
3.154
8.000
14.308
14.462
Figure 6. Dimensions and Plan View of a Standard EGS (in.) (100 A) Type 3R Enclosure.
IB70-8671
Instructional Booklet
Page 8
Check to ensure there are no pipes, wires, or other mounting hazards in the immediate mounting area that could create a problem.
WARNING
POWER CONDUCTORS MAY HAVE VOLTAGE PRESENT THAT CAN
CAUSE SEVERE PERSONAL INJURY OR DEATH. DE-ENERGIZE ALL
POWER OR CONTROL CIRCUIT CONDUCTORS TO BE CONNECTED
TO THE ATS EQUIPMENT BEFORE BEGINNING TO WORK WITH THE
CONDUCTORS AND/OR TERMINATING THEM TO THE EQUIPMENT
CAUTION
CAUTION
EXTREME CARE SHOULD BE TAKEN TO PROTECT THE ATS FROM
DRILL CHIPS, FILINGS, AND OTHER CONTAMINANTS WHEN MAKING THE CABLE ENTRY HOLES AND MOUNTING THE ENCLOSURE
TO PREVENT COMPONENT DAMAGE OR A FUTURE MALFUNCTION.
TO HELP PREVENT COMPONENT DAMAGE OR FUTURE MALFUNCTIONS, USE EXTREME CARE TO KEEP CONTAMINANTS OUT OF
THE ATS EQUIPMENT WHEN MAKING THE POWER CABLE CONNECTIONS.
NOTICE
Test all power cables prior to connection to the unit to ensure that
the conductors or cable insulation has not been damaged while
being pulled into position.
With the enclosed ATS equipment unpacked and ready for mounting, proceed with the following steps.
For Type 3R:
Step 1: Depress the padlockable catch at the bottom of the door
and slide the door downward (see Figure 7). Open the
door and remove the deadfront.
CONTACTOR WIRE
SIZE RANGE
NUMBER OF CABLES
PER PHASE
100
#14 2/0
Carefully strip the insulation from the power cables to avoid nicking or ringing of the conductor strands. Prepare the stripped conductor termination end by cleaning it with a wire brush. If
aluminum conductors are used, apply an appropriate joint compound to the clean conductor surface area.
CAUTION
IMPROPER POWER CABLE CONNECTIONS CAN CAUSE EXCESSIVE
HEAT AND SUBSEQUENT EQUIPMENT FAILURE.
Note:Tighten the cable lugs to the torque identified on the label affixed to
the unit.
NOTICE
The
The
The
The
The
Step 3: Mount the switch to a rigid structure as close to the electrical loads as possible.
IB70-8671
Instructional Booklet
Effective: July 2008
Page 9
UTILITY LUGS
NEUTRAL
UTILITY
LUGS
GENERATOR
LUGS
LOAD
LUGS
GROUND
UTILITY
LUGS
GEN LUGS
GENERATOR
LUGS
LOAD LUGS
IB70-8671
Instructional Booklet
Page 10
4.5 Wiring
WARNING
POWER CONDUCTORS AND CONTROL WIRING MAY HAVE VOLTAGE PRESENT THAT CAN CAUSE SEVERE PERSONAL INJURY OR
DEATH. DE-ENERGIZE ALL POWER OR CONTROL CIRCUIT CONDUCTORS BEFORE BEGINNING TO PERFORM ANY WIRING ACTIVITY TO
OR WITHIN THE ATS EQUIPMENT.
Utility
(Source 1)
Non-Critical
Loads
Watt-Hour
Meter
Utility Panel
CAUTION
CHECK THE ATS EQUIPMENT NAMEPLATE FOR RATED VOLTAGE.
IT SHOULD BE THE SAME AS THE UTILITY AND GENERATOR LINE
VOLTAGES. OPERATING THE EQUIPMENT ON IMPROPER VOLTAGE
CAN CAUSE EQUIPMENT DAMAGE.
Generator
(Source 2)
Transfer
Switch
4.6 Installation
Circuit Breaker
(typically included
in Genset)
In a typical installation for critical loads (see Figure 10), the ATS
(1) and the generator (2) are connected to the power supply. The
ATS and emergency distribution panel (1) receive utility power
from a dedicated breaker in the utility service panel (3). The ATS
and emergency panel receive generator power from the generator
(2). Power from the utility feeds the utility panel.
Critical
Loads
Di t ib ti
Note: Prior to making the generator utility sensing connection to the ATS,
set the generator control selector switch to the OFF position to prevent an
unwanted generator start. Control wiring, such as the generator utility
sensing wires, must be run separately from the power cables.
Use the proper wire size as listed by the generator set (Genset)
manufacturer.
This ATS is intended for use on generators with built in auto start
features. These generators sense, and react to, utility power.
Remote starting contacts are not provided in this transfer switch.
IB70-8671
Instructional Booklet
Effective: July 2008
Verify that the phase-to-phase line voltages of both the utility and
generator power sources are the same and that they match the
rated voltage as indicated on the ATS ratings label.
CAUTION
SEVERE EQUIPMENT DAMAGE CAN RESULT IF THE UNIT IS NOT
APPLIED AT PROPER VOLTAGE. DO NOT ENERGIZE THE EQUIPMENT IF THE SUPPLY VOLTAGES DO NOT MATCH EQUIPMENT
RATINGS LABEL.
Page 11
Step 1: Check all loads connected to the ATS to ensure that they
are ready to be energized.
Step 1: Close the upstream utility power source breaker or
switch to connect the ATS to the utility power source
voltage.
Step 2: Using a voltmeter, measure the line-to-line and the lineto-neutral voltages across the utility line terminals to
ensure the utility voltage is correct.
Step 3: If the voltage is acceptable, the solenoid will engage and
the contactor will automatically switch to the UTILITY
position.
4.9 Protection
For Catalog # EGS100L24R only
When protected by one of the following circuit breakers rated not
more than 150 amperes, this transfer switch is rated for use on a
circuit capable of delivering not more than 25,000 RMS symmetrical amperes, 240 volts maximum, but not more than the interrupting capacity of the selected circuit breaker.
Eaton/Cutler-Hammer
BR
CH
FDC
BW
BWH
Siemens
CED6 ED6
ED4
CSR
CSH
HED6
HED4
WARNING
CONTACT WITH ENERGIZED COMPONENTS WILL CAUSE ELECTRICAL SHOCK CAPABLE OF PRODUCING SEVERE PERSONAL INJURY
OR DEATH. USE EXTREME CAUTION TO AVOID CONTACT WITH
ENERGIZED COMPONENTS WHEN USING A METER FOR VOLTAGE
CHECKS.
NOTICE
THIS WILL SIMULATE AN INTERRUPTION OF THE UTILITY POWER
SOURCE.
IB70-8671
Instructional Booklet
Page 12
Step 5: The ATS Time Delay Normal (Utility) to Emergency (Generator) (TDNE) will begin to time after the generator
engine begins to run. After time out, the solenoid will
engage and the contactor will automatically switch from
the UTILITY to the GENERATOR position.
Step 6: Close the utility breaker described in Step 1 of
Section 5.2.
SECTION 6: ADJUSTMENTS
6.1 General
Refer to IB00405004E-70-8664, supplied with the ATS for
RTC-50 controller adjustments and functions.
IB70-8671
Instructional Booklet
O & M Manual for the EGS AutomaticTransfer Switch
with RTC-50 Control and Integral Loadcenter - 100 Amp
WARNING
HIGH VOLTAGES ARE PRESENT IN AND AROUND TRANSFER
SWITCH EQUIPMENT. BEFORE INSPECTING OR MAINTAINING THIS
EQUIPMENT, DISCONNECT THE LINE POWER FROM THE EQUIPMENT BEING SERVICED BY OPENING AND LOCKING OUT, IF POSSIBLE, THE NEXT HIGHEST DISCONNECT DEVICE. FAILURE TO
FOLLOW THIS PROCEDURE COULD CAUSE SEVERE PERSONAL
INJURY AND/OR DEATH.
In general, ATS equipment is designed to be relatively maintenance free under normal usage. However, because of the variabil-
Page 13
Figure 12. Wiring Diagram for the EGS100L24R ATS (Shown Deenergized).
IB70-8671
Instructional Booklet
Page 14
7.2 Procedures
A suggested maintenance procedure to be followed is outlined in Table 3.
ACTION
a. Make the transfer switch equipment safe for inspection and/or maintenance.
Disconnect the line power from the equipment being serviced by opening next highest disconnect
device. Make certain that any accessory control power is switched off.
b. Inspect the structure area for safety hazards or potential maintenance problems.
Inspect the area, especially where the contactor is installed, for any safety hazards, including personal safety and fire hazards. Exposure to certain chemical vapors can cause deterioration of the
electrical connections.
Inspect for accumulated dirt, loose hardware, or physical damage.
Examine the primary insulation for evidence of cracking or overheating. Overheating will show as
discoloration, melting, or blistering of the conductor insulation, or as pitting or melting of the conductor surfaces due to arcing.
Inspect the secondary control connections for damage, and control wiring for insulation integrity.
c. Inspect the contactor for dust, dirt, soot, grease, moisture, or corrosion.
Remove dust, dirt, soot, grease, moisture, and corrosion contamination from the surface of the
switching device using a dry, soft lint-free cloth, dry soft bristle brush, and vacuum cleaner. Do
not blow debris into the contactor. If contamination is found, look for the source and fix the problem.
Severe material cracking will require replacement and loose hardware will need to be tightened.
f. Exercise the contactor if it is not often exercised while in operation. This will permit the wiping If a switching device is used for frequent switching during normal operation, this step can be disreaction by the contacts.
garded.
g. Return the transfer switch equipment to service.
Make certain all barriers are in place and the door is closed. Re-apply generator and utility power.
IB70-8671
Instructional Booklet
O & M Manual for the EGS AutomaticTransfer Switch
with RTC-50 Control and Integral Loadcenter - 100 Amp
7.3 Maintenance Log
DATE
ACTION
Example: 01/01/04
IB70-8671
Page 15
Instructional Booklet
Page 16
PART NUMBER
Contactor
99-5638
ATS MODEL
100 A
RTC-50 Controller
RTC50
100 A
Harness EGS
99-5638-3
100 A
99-5638-4
100 A
Ground Bar
99-5638-15
100 A
Lugs
99-5638-6
100 A
Neutral Bar
99-5638-17
100 A
SurgTel
DHW4PT
100 A
SurgCable
DCXCAB2
100 A
TVSS
99-5638-10
100 A
WARNING
RTC-50
Controller
NOTICE
APPLY UTILITY (SOURCE 1) POWER AND PLACE THE GENERATOR
CONTROL SELECTOR SWITCH IN THE AUTO POSITION AFTER THE
COMPONENT HAS BEEN REPLACED. TEST THE SYSTEM FOR
PROPER FUNCTIONALITY.
IB70-8671
Instructional Booklet
Effective: July 2008
Page 17
Step 2: Disconnect the J1, J2, J3, J4, and J6 plugs from the controller (see Figure 14).
Step 3: Disconnect the wires connected to J7 and J8.
Step 4: Remove the four (4) screws located at the corners of the
controller that secure it to the power panel. Remove the
controller (see Figure 14).
CONNECTORS
J1-J4
MOUNTING
SCREWS
NEUTRAL BARS
Figure 15. 100 A Neutral Bar.
Step 1: Turn the utility (Source 1) power off and turn the generator (Source 2) control selector switch to the OFF position before attempting to replace the neutral bar.
Step 2: Disconnect all wire cables from the neutral bar.
Step 3: Remove the two screws in the black base using a blade
screwdriver or 0.375 in. socket or nut driver. Remove the
strap with a common straight blade screw driver and then
remove the neutral bar.
J8
J7
J6
SCREWS
Step 6: Connect the J1, J2, J3, J4, and J6 plugs to their original
receptacles.
Step 7: Reconnect the wires to J7 and J8.
Step 8: Reapply power to the transfer switch.
Step 9: Place the generator control selector switch in the AUTO
position after the controller has been replaced. (The Generator may start but will shut down with in 5 minutes.)
Test the system for proper functionality.
IB70-8671
Step 6:
Step 7:
Instructional Booklet
Page 18
N1
E1
N2
E2
UTILITY AUX.
SWITCH
UTILITY
COIL
GENERATOR AUX.
SWITCH
GENERATOR
COIL
MOUNTING
SCREWS
Step 1: Turn the utility (Source 1) power off and turn the generator (Source 2) control selector switch to the OFF position before attempting to replace the contactor.
GROUND BAR
Step 2: Note their location then disconnect the twelve (12) red
wires from the contactor (see Figure 18).
Note: All wires connected to the contactor are labeled to ease
identification.
Step 3: Remove the four (4) screws securing the contactor to the
base plate using a blade screwdriver or 0.25 in. socket or
nut driver. Remove the contactor.
Step 4: Following the replacement steps for the 100 A lugs (see
Sections 7.4.1.6), remove the lugs from the old contactor
then install the lugs on the new contactor.
Step 5: Secure the contactor onto the base plate using the hardware supplied.
Step 6: Reattach the twelve (12) red wires to the contactor.
Examine each wire to find the name then refer to Figure
18 for the correct connection point.
IB70-8671
Instructional Booklet
Effective: July 2008
Page 19
Step 3: Disconnect the J1, J2, J3, J4, J6, J7, and J8 plugs from
the controller (see Figure 14).
UTILITY
LUGS
GENERATOR
LUGS
N1
N2
E1
E2
LOAD LUGS
Figure 21. Replacing the 100 A Lugs.
Step 1: Turn the utility (Source 1) power off and turn the generator (Source 2) control selector switch to the OFF position before attempting to replace the lugs.
Step 2: Disconnect all wire cables from the contactor.
Step 3: Note their location then disconnect the red wires from the
contactor (see Figure 18).
Note: All wires connected to the contactor are labeled to ease
identification.
UTILITY COIL
CONNECTIONS
UTILITY GEN
GENERAL
AUX
AUX
COIL
N.C. GEN CONNECTIONS
UTILITY N.C.
AUX
AUX
COM
COM.
Instructional Booklet
Page 20
Step 10: Secure the contactor to the base plate using the four (4)
screws supplied.
Step 11: Reattach the red wires to the contactor. Examine each
wire to find the name then refer to Figure 21 for the correct connection point.
Step 7: Place the new utility lugs on the utility bus so the antiturn protrusions fit in the holes. Once the lugs are in
place, take one (1) supplied control wire terminal and
hold it underneath the bus. Using one (1) screw and one
(1) washer supplied, tighten the control wire terminal and
lug to the utility bus. Repeat the process of the second
utility lug. Ensure that no gaps are present between the
lugs and bus.
Step 12: Reconnect all cables to the contactor as per their original
connections.
7.5 Troubleshooting
Step 13: Apply utility (Source 1) power and place the generator
control selector switch in the AUTO position after the
lugs have been replaced. Test the system for proper
functionality.
CAUSE
CORRECTION
The generator is still running after the transfer switch transfers to the utility.
IB70-8671
Instructional Booklet
O & M Manual for the EGS AutomaticTransfer Switch
with RTC-50 Control and Integral Loadcenter - 100 Amp
Notes:
IB70-8671
Page 21
Instructional Booklet
Page 22
Notes:
IB70-8671
Instructional Booklet
O & M Manual for the EGS AutomaticTransfer Switch
with RTC-50 Control and Integral Loadcenter - 100 Amp
Notes:
IB70-8671
Page 23
Instructional Booklet
Page 24
This instruction booklet is published solely for information purposes and should not be considered all-inclusive. If further information is required, you should consult an authorized Eaton sales
representative.
The sale of the product shown in this literature is subject to the
terms and conditions outlined in appropriate Eaton selling policies
or other contractual agreement between the parties. This literature is not intended to and does not enlarge or add to any such
contract. The sole source governing the rights and remedies of
any purchaser of this equipment is the contract between the purchaser and Eaton.
NO WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING WARRANTIES OF FITNESS FOR A PARTICULAR PURPOSE OR MERCHANTABILITY, OR WARRANTIES ARISING FROM COURSE OF
DEALING OR USAGE OF TRADE, ARE MADE REGARDING THE
INFORMATION, RECOMMENDATIONS, AND DESCRIPTIONS
CONTAINED HEREIN. In no event will Eaton be responsible to the
purchaser or user in contract, in tort (including negligence), strict
liability or otherwise for any special, indirect, incidental or consequential damage or loss whatsoever, including but not limited to
damage or loss of use of equipment, plant or power system, cost
of capital, loss of power, additional expenses in the use of existing power facilities, or claims against the purchaser or user by its
customers resulting from the use of the information, recommendations and description contained herein.
Eaton Corporation
Electrical Group
1000 Cherrington Parkway
Moon Township, PA 15108
United States
877-ETN CARE (877-386-2273)
Eaton.com
Nueva informacin
Descripcin
Pgina
1. Introduccin . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2. Recepcin, manipulacin y almacenamiento . . . . . .
3. Descripcin del equipo . . . . . . . . . . . . . . . . . . . . .
4. Instalacin y cableado . . . . . . . . . . . . . . . . . . . . .
5. Prueba de funcionamiento . . . . . . . . . . . . . . . . . .
6. Ajustes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7. Mantenimiento y reemplazo de piezas componentes
IB70-8671
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
2
5
5
7
11
12
13
Folleto informativo
Pgina 2
SECCIN 1: INTRODUCCIN
ADVERTENCIA
LEA Y COMPRENDA LAS INSTRUCCIONES AQU CONTENIDAS
ANTES DE PROCEDER A DESEMPACAR, ENSAMBLAR, OPERAR O
MANTENER ESTE EQUIPO.
DENTRO DE LAS CAJAS PROTECTORAS DE LOS INTERRUPTORES
DE TRANSFERENCIA HAY PRESENTES VOLTAJES PELIGROSOS QUE
PUEDEN CAUSAR MUERTE O HERIDAS PERSONALES SEVERAS.
SIGA LOS PROCEDIMIENTOS APROPIADOS PARA LA INSTALACIN,
OPERACIN Y MANTENIMIENTO, PARA EVITAR ESTOS VOLTAJES.
EL EQUIPO DE INTERRUPTOR DE TRANSFERENCIA CUBIERTO POR
ESTE LIBRO DE INSTRUCCIONES EST DISEADO Y PROBADO
PARA OPERAR DENTRO DE LA CAPACIDAD QUE SE MUESTRA EN
LA PLACA CON LAS CARACTERSTICAS. LA OPERACIN FUERA DE
ESTA CAPACIDAD PUEDE CAUSAR QUE EL EQUIPO FALLE,
RESULTANDO EN MUERTE, HERIDAS SERIAS EN EL CUERPO Y/O
DAOS A LA PROPIEDAD. TODO EL PERSONAL RESPONSABLE DEBE
LOCALIZAR LA PLACA CON CARACTERSTICAS DEL EQUIPO MONTADA EN LA PUERTA, Y FAMILIARIZARSE CON LA INFORMACIN
PROPORCIONADA SOBRE DICHA PLACA. UNA PLACA CON CARACTERSTICAS DE EQUIPO TPICA ES MOSTRADA EN LA FIGURA 1.
.
L050412234
Cat N: EGS100L24R
Estilo N:
GO N: ABC0123
Voltios: 240
Polos: 2
Amperios: 100
Fase: 1
CAJA TIPO: 3R
ARTCULO N: 001
PIEZA: 001
DE: 001
Hercios: 60
Cables: 3
30-43465
ADVERTENCIA
LAS ADVERTENCIAS Y PRECAUCIONES INCLUIDAS COMO PARTE
DE LOS PASOS DEL PROCEDIMIENTO EN ESTE DOCUMENTO SON
PARA LA SEGURIDAD PERSONAL Y LA PROTECCIN DEL EQUIPO
CONTRA DAOS. UN EJEMPLO DE TTULO DE UNA ETIQUETA DE
ADVERTENCIA TPICA ES MOSTRADO ARRIBA, PARA FAMILIARIZAR AL PERSONAL CON EL ESTILO DE PRESENTACIN. ESTO AYUDAR A ASEGURAR QUE EL PERSONAL EST ALERTA A LAS
ADVERTENCIAS QUE APARECEN A TRAVS DE TODO EL DOCUMENTO. EN ADICIN, LAS PRECAUCIONES APARECEN TODAS EN
LETRAS MAYSCULAS EN NEGRITA.
PRECAUCIN
LEA Y COMPRENDA EL MATERIAL PRESENTADO EN ESTE DOCUMENTO ANTES DE PROCEDER A INSTALAR, APLICAR, OPERAR O
MANTENER ESTE EQUIPO. EN ADICIN, SLO SE DEBE PERMITIR A
PERSONAS CALIFICADAS REALIZAR CUALQUIER TRABAJO ASOCIADO CON ESTE EQUIPO. CUALQUIER INSTRUCCIN SOBRE EL
CABLEADO PRESENTADA EN ESTE DOCUMENTO DEBE SER
SEGUIDA PRECISAMENTE. EL NO HACERLO, PUEDE CAUSAR DAO
PERMANENTE AL EQUIPO.
IB70-8671
Folleto informativo
Efectivo: julio 2008
Generador
Pgina 3
ADVERTENCIA
NO TRANSFIERA MANUALMENTE EL INTERRUPTOR MIENTRAS
EST BAJO CARGA.
Servicio
Carga
Figura 2. Esquema del interruptor (contactor) de transferencia de
carga tpico.
Un sistema de informacin inicia la transferencia cuando la fuente
de energa del servicio falla o cae por debajo de un voltaje prefijado. El generador inicia entonces un arranque del motor y el ATS
transfiere a la fuente de energa del generador cuando hay disponible suficiente voltaje en el mismo. Cuando la fuente de
energa del servicio es restaurada, el ATS automticamente transfiere nuevamente, y el generador se interrumpe despus de un
tiempo de retraso. En el caso de que la fuente de energa del servicio falla y la fuente de energa del generador no aparece, el ATS
permanece conectado a la fuente de energa del servicio hasta que
la fuente de energa del generador aparece. A la inversa, si est
conectado a la fuente de energa del generador y la misma falla
mientras la fuente de energa del servicio todava no est disponible, el ATS permanece conectado a la fuente de alimentacin
del generador.
Los ATS automticamente realizan la funcin de transferencia, e
incluyen tres elementos bsicos.
1. Contactos principales para conectar y desconectar la carga
hacia y desde la fuente de alimentacin.
2. Solenoides para hacer la transferencia de los contactos principales desde fuente a fuente.
3. Circuitos de informacin/supervisin para controlar constantemente la condicin de las fuentes de alimentacin y as proporcionar la informacin necesaria para el interruptor y la
operacin afn del circuito.
IB70-8671
Folleto informativo
Pgina 4
100
Fabricante
Eaton
Tipo
Interruptor
de
generador
Capacidad
nominal en
amperios
100 = 100 A
L 24
Centro de carga
L24- 24 circuitos
R
Tipo de caja
protectora
R = Tipo 3R
Servicio
El servicio es la fuente primaria (fuente normal, fuente de alimentacin normal o normal).
Generador
El generador es la fuente secundaria (fuente de emergencia de
generador, fuente de alimentacin de emergencia, emergencia, de
reserva, fuente de refuerzo).
Servicio: fallido o en falla
El servicio es definido como "en falla" cuando est por fuera de
sus lmites de valores fijados de bajo voltaje para la seleccin de
voltaje y frecuencia nominal.
Generador: fallido o en falla
El generador es definido como "en falla" cuando est por fuera de
sus lmites de valores fijados de bajo voltaje/baja frecuencia/sobre
frecuencia (si es aplicable) para la seleccin de voltaje y frecuencia
nominal, por un perodo excediendo 0,5 segundo despus de que
el tiempo de retraso de emergencia de falla (TDEF) expira.
Transferencia
1.5 Glosario
La siguiente terminologa es definida con respecto a su uso en
este documento y cmo se relaciona con el interruptor de transferencia y la operacin del controlador.
Disponible
Una fuente de alimentacin es definida como "disponible" cuando
se encuentra dentro de sus lmites de valores fijados de bajo
voltaje para la seleccin de voltaje nominal.
Conectado
"Conectado" es definido cuando la entrada est sometida a cortocircuito por un contacto o conexin externos.
Fallido o falla
Una fuente es definida como "en falla" cuando est por fuera de
los lmites de valores fijados de voltaje aplicable para el voltaje
nominal y para un perodo de tiempo que excede 0,5 segundo
despus del tiempo de retraso de emergencia de falla (TDEF)
expira.
Mecanismo de seguridad
El mecanismo de seguridad es una caracterstica que evita la
desconexin de la nica fuente de alimentacin disponible y tambin fuerza una operacin de transferencia o re-transferencia a la
nica fuente de alimentacin disponible.
Re-transferencia
Re-transferencia se define como un cambio de la conexin de
carga desde el generador hacia el servicio.
IB70-8671
Folleto informativo
Efectivo: julio 2008
Pgina 5
2.2 Manipulacin
Tal como se mencion previamente, el equipo ATS est embalado
en su propia caja. Proteja el equipo contra impactos en todo
momento y no lo apile. Una vez que el equipo est en el sitio de
instalacin y listo para ser instalado, el material de embalaje puede
ser quitado. Refirase a la seccin 4 de este manual para las
instrucciones de instalacin especficas.
2.3 Almacenamiento
Si bien est correctamente embalado, este equipo no es adecuado
para almacenamiento en el exterior. La garanta del equipo no ser
aplicable si hay evidencia de almacenamiento en el exterior. Si el
equipo va a ser almacenado en el interior por cualquier perodo de
tiempo, debe ser almacenado con el material protector del embalaje en su lugar. Proteja el equipo en todo momento contra
humedad excesiva, polvo de construccin, condiciones corrosivas
y otros contaminantes. Se sugiere firmemente que el equipo protegido por el embalaje sea almacenado en un ambiente con control
climtico de -20 a 70C (-4 a 158F), con una humedad relativa de
80% o menos. Bajo ninguna circunstancia apile otro equipo
encima de la caja protectora del equipo ATS, embalado o no.
IB70-8671
Folleto informativo
Pgina 6
3.
El RTC-50 es un paquete de control lgico de interruptor de transferencia en base a microprocesador. El hardware y software del
controlador contienen los circuitos de informacin/supervisin que
constantemente controlan la condicin de las fuentes de alimentacin. Proporciona la informacin necesaria para la operacin del
ATS (figura 5).
5.
IB70-8671
Folleto informativo
Efectivo: julio 2008
Pgina 7
3.5 Normas
El equipo ATS de Eaton est enlistado para su aplicacin por UL.
Adems, los ATS de Eaton estn enlistados en el archivo
E316586 por Underwriters Laboratories, Inc. bajo la norma estndar UL 1008 y UL 67. Esta norma cubre los requisitos para los
ATS destinados a uso en localizaciones comunes, para proporcionar iluminacin y energa como sigue:
a. En sistemas de reserva, de acuerdo con el artculo 702
del Cdigo Elctrico Nacional.
Los ATS de Eaton estn disponibles para cumplir con NFPA 110
para sistemas de energa de reserva.
Los equipos ATS de Eaton estn enlistados para su aplicacin por
CSA. Adems, los ATS de Eaton est enlistados en el archivo Legacy LR96245 Master Contract 163545 por la Canadian Standard
Association (CSA) bajo la norma 22.2#178-1978.
4.1 General
Los ATS de Eaton estn conectados con sus cables y probados en
fbrica. La instalacin requiere el montaje slido de la unidad y la
conexin de los cables de alimentacin y los circuitos sensores
auxiliares. En esta seccin se cubren los procedimientos de montaje fsico y las conexiones de los cables de alimentacin.
Una vez que el interruptor de transferencia est correctamente
instalado y conectado, debe ser verificado mecnica y elctricamente para una instalacin y una operacin correctas. Los procedimientos para estas verificaciones mecnicas y elctricas iniciales
estn delineados en la seccin 5 de este manual.
ADVERTENCIA
ASEGRESE DE QUE EL FRENTE CIEGO EST CORRECTAMENTE
INSTALADO ANTES DE QUE EL EQUIPO INTERRUPTOR DE TRANSFERENCIA SEA PUESTO EN SERVICIO. EL FRENTE CIEGO PROPORCIONA PROTECCIN CONTRA VOLTAJES PELIGROSOS EN LA LNEA
Y EN LOS TERMINALES DE CARGA CUANDO EL EQUIPO EST FUNCIONANDO. NO HACERLO PUEDE OCASIONAR HERIDAS PERSONALES O MUERTE.
5.321
7.154
5.321
2.633
2.496
14.462
5.198
19.005
29.332
3.154
8.000
14.308
14.462
Figura 6. Dimensiones y vista del plano de una caja protectora tipo 3R para un EGS estndar (en pulgadas) (100 A).
IB70-8671
Folleto informativo
Pgina 8
ADVERTENCIA
LOS CONDUCTORES DE ENERGA PUEDEN TENER VOLTAJE PRESENTE QUE PUEDE CAUSAR SEVERAS HERIDAS PERSONALES O
MUERTE. QUITE LA ENERGA DE TODOS LOS CONDUCTORES DE
CIRCUITO DE CONTROL O ALIMENTACIN QUE VAYAN A SER
CONECTADOS AL EQUIPO ATS, ANTES DE COMENZAR A TRABAJAR CON LOS CONDUCTORES Y/O CONECTAR SUS TERMINALES
AL EQUIPO.
PRECAUCIN
PRECAUCIN
AVISO
LA INSTALACIN DEBE CUMPLIR TOTALMENTE CON TODOS LOS
CDIGOS, NORMAS Y REGULACIONES PERTINENTES.
Con el equipo del ATS desembalado y listo para ser montado, proceda con los siguientes pasos.
Para el tipo 3R:
Paso 1: Baje la armella asegurable que se encuentra en la parte
inferior de la puerta y deslice la puerta hacia abajo (vea la
figura 7). Abra la puerta y quite el frente ciego.
100
#14 2/0
PRECAUCIN
LAS CONEXIONES INCORRECTAS DE CABLES DE ALIMENTACIN
PUEDEN CAUSAR EXCESIVO CALOR Y LA CONSECUENTE FALLA
DEL EQUIPO.
Nota: Ajuste las orejetas del cable hasta el par de torsin identificado en la
etiqueta colocada sobre la unidad.
Paso 1: Conecte los cables como sigue (vea las figura 8 y la tabla
2):
AVISO
PARA EL CABLEADO DE CONTROL (CABLEADO PARA ARRANQUE
DEL MOTOR DEL GENERADOR), LOS CABLES DEBEN ESTAR AISLADOS DE AMBOS, LOS CABLES DE ALIMENTACIN DEL SERVICIO Y
DEL GENERADOR.
Paso 3: Monte el interruptor sobre una estructura rgida tan cercano a las cargas elctricas como sea posible.
IB70-8671
Folleto informativo
Efectivo: julio 2008
Pgina 9
OREJETAS
DEL SERVICIO
NEUTRO
OREJETAS
DEL
SERVICIO
OREJETAS
DEL GENERADOR
OREJETAS
DE
CARGA
GENERATOR
START TERMINALS
CONEXIN
A TIERRA
OREJETAS
DEL GENERADOR
OREJETAS DE
CARGA
IB70-8671
Folleto informativo
Pgina 10
4.5 Cableado
ADVERTENCIA
LOS CONDUCTORES DE ENERGA Y EL CABLEADO DE CONTROL
PUEDEN TENER VOLTAJE PRESENTE QUE PUEDE CAUSAR SEVERAS
HERIDAS PERSONALES O MUERTE. QUITE LA ENERGA DE TODOS
LOS CONDUCTORES DE CIRCUITO DE CONTROL O ALIMENTACIN
ANTES DE COMENZAR A REALIZAR CUALQUIER ACTIVIDAD DE
CABLEADO HACIA O ADENTRO DEL EQUIPO ATS.
Cargas no crticas
Servicio
(fuente de
alimentacin 1)
Medidor de
Watt-hora
PRECAUCIN
VERIFIQUE EN LA PLACA CON LAS CARACTERSTICAS DEL EQUIPO
ATS, EL VOLTAJE NOMINAL. DEBE SER EL MISMO QUE LOS
VOLTAJES DE LNEA DEL SERVICIO Y EL GENERADOR. LA OPERACIN DEL EQUIPO EN VOLTAJE INCORRECTO PUEDE OCASIONAR
DAOS AL EQUIPO.
Interruptor de
transferencia
Generador
(fuente de
alimentacin 2)
Cortacircuitos
(tpicamente incluido
en Genset)
4.6 Instalacin
En una instalacin tpica para cargas crticas (vea la figura 10), el
ATS (1) y el generador (2) estn conectados a la alimentacin de
energa. El ATS y el panel de distribucin de emergencia (1)
reciben energa del servicio de un cortacircuito dedicado en el
panel del servicio (3). El ATS y el panel de emergencia reciben
energa generadora desde el generador (2). La energa del servicio
alimenta el panel del servicio.
Cargas crticas
Cableado
de control
IB70-8671
Folleto informativo
Efectivo: julio 2008
PRECAUCIN
SI LA UNIDAD NO ES APLICADA CON EL VOLTAJE CORRECTO, SE
PUEDEN CAUSAR SEVEROS DAOS AL EQUIPO. NO ALIMENTE AL
EQUIPO CON ENERGA SI LOS VOLTAJES DE ALIMENTACIN NO
COINCIDEN CON LOS VALORES NOMINALES MOSTRADOS EN LA
ETIQUETA DEL EQUIPO.
4.9 Proteccin
ADVERTENCIA
ED6
Pgina 11
ED4
HED6
HED4
AVISO
ESTO SIMULAR UNA INTERRUPCIN DE LA FUENTE DE ALIMENTACIN DEL SERVICIO.
CORTACIRCUITOS - CUALQUIERA
TIPO - CUALQUIERA
AMPERIOS MXIMOS - SEGN NEC
IB70-8671
Folleto informativo
Pgina 12
Paso 4: Cierre el cortacircuitos o el interruptor de la fuente de alimentacin del generador de contracorriente, para conectar el ATS a la fuente de alimentacin del generador.
SECCIN 6: AJUSTES
6.1 General
IB70-8671
Folleto informativo
Efectivo: julio 2008
ADVERTENCIA
DENTRO Y ALREDEDOR DEL EQUIPO DEL INTERRUPTOR DE TRANSFERENCIA HAY PRESENTES ALTOS VOLTAJES. ANTES DE INSPECCIONAR O MANTENER ESTE EQUIPO, DESCONECTE LA ENERGA DE
LA LNEA DEL EQUIPO QUE SE EST ATENDIENDO, ABRIENDO Y
TRABANDO, DE SER POSIBLE, EL DISPOSITIVO DE DESCONEXIN
MS ALTO SIGUIENTE. EL NO SEGUIR ESTE PROCEDIMIENTO
PUEDE CAUSAR SEVERAS HERIDAS PERSONALES Y/O MUERTE.
Pgina 13
confiabilidad de la operacin en este tipo de equipo, se deben realizar controles de inspeccin y mantenimiento regularmente planeados. Dado que el mantenimiento del equipo consistir
principalmente en mantener el equipo limpio, la frecuencia de
mantenimiento depender, en gran medida, de la limpieza del
entorno del mismo. Si hay presente una cantidad significativa de
polvo o materias extraas, se deber seguir un programa de mantenimiento ms frecuente.
Se sugiere realizar inspecciones visuales del equipo regularmente,
no solamente durante los perodos programados. Siempre est
alerta a la acumulacin de polvo dentro y alrededor de la estructura, piezas sueltas y/o herrajes, rajaduras y/o decoloracin en el
aislamiento, y piezas componentes daadas o decoloradas.
La figura 12 muestra el diagrama de cableado para el interruptor
ATS EGS de 100 A.
Nota: Solamente personal calificado y experimentado debe realizar cualquier trabajo de diagnstico utilizando este diagrama.
MECANISMO DE TRANSFERENCIA
VOLTAJE DE ALIMENTACIN
DEL GENERADOR
PANEL DE DISTRIBUCIN
PRINCIPAL (CARGA)
ALIMENTACIN DEL
SERVICIO 240 V CA
REAJUSTE DEL
MANTENIMIENTO
INDICADOR DE
MANTENIMIENTO
DETECTANDO
DESCONEXIN
DE LA CARGA
DESCONEXIN
DE LA CARGA
FUENTE DE ALIMENTACIN
1 CERRADA
FUENTE DE ALIMENTACIN
2 CERRADA
Figura 12. Diagrama de cableado para el ATS EGS de 100L24R A (aqu se muestra desactivado).
IB70-8671
Folleto informativo
Pgina 14
7.2 Procedimientos
En la tabla 3 se delinea un procedimiento de mantenimiento que se sugiere seguir.
ACCIN
Desconecte la energa de la lnea del equipo que se est atendiendo, abriendo el dispositivo de
desconexin prximo ms alto. Asegrese de que toda la alimentacin de control de los accesorios
est desconectada.
b. Inspeccione el rea de la estructura para detectar cualquier peligro a la seguridad o problemas Inspeccione el rea, especialmente donde el contactor est instalado, para detectar cualquier pelipotenciales de mantenimiento.
gro a la seguridad, incluyendo la seguridad personal y peligro de incendios. La exposicin a ciertos
vapores qumicos puede causar deterioro a las conexiones elctricas.
Inspeccione la acumulacin de suciedad, piezas sueltas o daos fsicos.
Examine el aislamiento primario para detectar evidencias de quebraduras o sobrecalentamiento. El
sobrecalentamiento se notar como decoloracin, derretimiento o ampollas en el aislamiento del
conductor, o como picaduras o derretimiento de las superficies del conductor debido a arcos elctricos.
Inspeccione las conexiones de control secundarias para detectar daos, y el cableado de control,
para verificar la integridad del aislamiento.
c. Inspeccione el contactor para detectar la presencia de polvo, suciedad, holln, grasa, humedad o Quite polvo, suciedad, holln, grasa, humedad y contaminacin por corrosin de la superficie del
corrosin.
dispositivo interruptor, utilizando un pao suave seco y libre de pelusas, un cepillo de cerdas suaves y seco, y una aspiradora. No sople los residuos dentro del contactor. Si se encuentra contaminacin, busque la fuente de la misma y solucione el problema.
d. Examine la integridad del material, desgaste desparejo, decoloracin o piezas sueltas.
El agrietamiento severo del material requerir su reemplazo y las piezas sueltas requerirn ser ajustadas.
Si se utiliza un dispositivo interruptor para cambios frecuentes durante la operacin normal, este
paso puede ser descartado.
Asegrese de que todas las barreras estn en su lugar y que la puerta est cerrada. Vuelva a aplicar la energa del generador y el servicio.
IB70-8671
Folleto informativo
Manual de operacin y mantenimiento para el interruptor
automtico de transferencia EGS con control RTC-50
y centro de carga incorporado - 100 Amp
ACCIN
Ejemplo: 01/01/04
Inspeccin y limpieza.
IB70-8671
Pgina 15
Folleto informativo
Pgina 16
PIEZA NMERO
MODELO DE ATS
Contactor
99-5638
100 A
Controlador RTC-50
RTC502
100 A
Arns EGS
99-5638-3
100 A
99-5638-4
100 A
99-5638-15
100 A
Orejetas
99-5638-6
100 A
Barra neutra
99-5638-17
100 A
DHW4PT
100 A
DCXCAB2
100 A
TVSS
99-5638-10
100 A
ADVERTENCIA
DENTRO Y ALREDEDOR DEL EQUIPO DEL INTERRUPTOR DE TRANSFERENCIA HAY ALTOS VOLTAJES PRESENTES. ANTES DE INTENTAR REEMPLAZAR CUALQUIER PIEZA COMPONENTE, DESCONECTE
LA ENERGA DE LA LNEA DEL EQUIPO QUE SE EST ATENDIENDO,
ABRIENDO Y TRABANDO, DE SER POSIBLE, EL DISPOSITIVO DE
DESCONEXIN MS ALTO SIGUIENTE. EL NO SEGUIR ESTE PROCEDIMIENTO PUEDE CAUSAR SEVERAS HERIDAS PERSONALES Y/O
MUERTE.
ANTES DE INTENTAR REEMPLAZAR CUALQUIER PIEZA COMPONENTE, SIEMPRE DESCONECTE LA ENERGA DEL SERVICIO (FUENTE
DE ALIMENTACIN 1) Y COLOQUE EL INTERRUPTOR SELECTOR DE
CONTROL DEL GENERADOR (FUENTE DE ALIMENTACIN 2) EN LA
POSICIN "OFF" (DESCONECTADO).
Controlador
RTC-50
AVISO
DESPUS DE HABER REEMPLAZADO LA PIEZA COMPONENTE, APLIQUE LA ENERGA DEL SERVICIO (FUENTE DE ALIMENTACIN 1) Y
COLOQUE EL INTERRUPTOR SELECTOR DE CONTROL DEL GENERADOR EN LA POSICIN "AUTO" (AUTOMTICO). PRUEBE EL
SISTEMA PARA VERIFICAR EL FUNCIONAMIENTO CORRECTO.
IB70-8671
Folleto informativo
Efectivo: julio 2008
Pgina 17
Paso 2: Desconecte los enchufes J1, J2, J3, J4 y J6 del controlador (vea la figura 14).
Paso 3: Desconecte los cables conectados a J7 y J8.
Paso 4: Quite los cuatro (4) tornillos, localizados en las esquinas
del controlador, que lo aseguran al panel de energa.
Quite el controlador (vea la figura 14).
CONECTORES
J1-J4
TORNILLOS
DE
MONTAJE
BARRAS NEUTRAS
Figura 15. Barra neutra de 100 A.
Paso 1: Desconecte la alimentacin del servicio (fuente de alimentacin 1) y coloque el interruptor selector de control del
generador (fuente de alimentacin 2) en la posicin
"OFF" (desconectado) antes de intentar reemplazar la
barra neutra.
Paso 2: Desconecte todos los cables de la barra neutra.
J8
J7
J6
TORNILLOS
IB70-8671
Folleto informativo
Pgina 18
N1
E1
N2
E2
INTERRUPTOR
AUXILIAR DEL
SERVICIO
BOBINA DEL
SERVICIO
INTERRUPTOR
AUXILIAR DEL
GENERADOR
BOBINA DEL
GENERADOR
OREJETA DE CONEXIN
A TIERRA
Nota: Todos los cables conectados al contactor estn rotulados para facilitar su identificacin.
IB70-8671
Folleto informativo
Efectivo: julio 2008
Pgina 19
OREJETAS
DEL SERVICIO
N2
N1
E1
E2
OREJETAS
DE CARGA
AUXILIAR
CONEXIONES
DEL
DE LA BOBINA
DEL
GENERADOR
GENERADORE
N.C.
AUXILIAR
DEL GENERADOR
COM.
Folleto informativo
Pgina 20
CAUSA
CORRECCIN
El generador est todava funcionando despus de que el interruptor de transferencia transfiere al servicio.
IB70-8671
Folleto informativo
Manual de operacin y mantenimiento para el interruptor
automtico de transferencia EGS con control RTC-50
y centro de carga incorporado - 100 Amp
Notas:
IB70-8671
Pgina 21
Folleto informativo
Pgina 22
Notas:
IB70-8671
Folleto informativo
Manual de operacin y mantenimiento para el interruptor
automtico de transferencia EGS con control RTC-50
y centro de carga incorporado - 100 Amp
Notas:
IB70-8671
Pgina 23
Folleto informativo
Pgina 24
Eaton Corporation
Electrical Group
1000 Cherrington Parkway
Moon Township, PA 15108
Estados Unidos
877-ETN CARE (877-386-2273)
Eaton.com
Nouveau document
Sommaire
Page
1. Introduction . . . . . . . . . . . . . . . . . .
2. Rception, manipulation et remisage .
3. Description du matriel . . . . . . . . . .
4. Installation et cblage . . . . . . . . . . .
5. Essais de fonctionnement. . . . . . . . .
6. Rglages . . . . . . . . . . . . . . . . . . . .
7. Entretien et remplacement des pices
IB70-8671
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
2
5
5
7
11
12
13
Livret d'instructions
Page 2
SECTION 1: INTRODUCTION
MISE EN GARDE
VEUILLEZ LIRE ET BIEN COMPRENDRE LES DIRECTIVES DE CE DOCUMENT AVANT D'ESSAYER DE DBALLER, D'ASSEMBLER, D'UTILISER OU DE RPARER CE MATRIEL.
LES TENSIONS DANGEREUSES POUVANT TRE PRSENTES
L'INTRIEUR DES BOTIERS DES COMMUTATEURS DE TRANSFERT
PEUVENT OCCASIONNER DES BLESSURES GRAVES OU MORTELLES. POUR VITER CES TENSIONS, RESPECTEZ LES MODES
D'INSTALLATION, D'EMPLOI ET D'ENTRETIEN.
LE COMMUTATEUR DE TRANSFERT CONCERN PAR CE DOCUMENT
EST CONU ET ESSAY POUR TRE UTILIS SELON LES SPCIFICATIONS DE SA PLAQUE D'IDENTIFICATION. UTILISER CE MATRIEL
EN DEHORS DE CES NORMES PEUT ENTRANER UNE PANNE DU
MATRIEL ET OCCASIONNER DES BLESSURES CORPORELLES OU
MORTELLES ET DES DGTS MATRIELS. LE PERSONNEL RESPONSABLE DOIT REPRER LA PLAQUE D'IDENTIFICATION AU DOS DE LA
PORTE ET SE FAMILIARISER AVEC LES RENSEIGNEMENTS QUI Y
SONT INDIQUS. LA FIGURE 1 MONTRE UNE PLAQUE D'IDENTIFICATION TYPE.
.
L050412234
Cat No: EGS100L24R
Style No:
GO No: ABC0123
Volts: 240
Poles: 2
Amps: 100
Phase: 1
ENCL TYPE: 3R
ITEM: 001
PIECE: 001
OF: 001
Hertz: 60
Wire: 3
30-43465
MISE EN GARDE
LES MISES EN GARDE ET AVIS DE DANGER INCLUS DANS LES
TAPES DE CE DOCUMENT SONT DONNS POUR LA SCURIT DES
PERSONNES ET LA PROTECTION DU MATRIEL CONTRE TOUS
DGTS. UN EXEMPLE DE MISE EN GARDE TYPE EST MONTR CIDESSUS AFIN DE FAMILIARISER LE PERSONNEL AVEC LEUR
PRSENTATION DANS LE DOCUMENT. CECI PERMET DE BIEN
AVERTIR LE PERSONNEL CONCERNANT CES AVIS TOUT AU LONG
DU DOCUMENT. EN OUTRE, LES AVIS DE DANGER SONT EN
MAJUSCULES ET EN GRAS.
ATTENTION
VEUILLEZ LIRE ET BIEN COMPRENDRE LES DIRECTIVES DE CE DOCUMENT AVANT D'ESSAYER D'INSTALLER, DE BRANCHER, D'UTILISER OU DE RPARER CE MATRIEL. DE PLUS, SEUL LE
PERSONNEL QUALIFI DOIT TRE AUTORIS EFFECTUER LES RPARATIONS DE CE MATRIEL. LES DIRECTIVES DE CBLAGE
PRSENTES DANS CE DOCUMENT DOIVENT TRE SUIVIES LA
LETTRE, SOUS PEINE D'OCCASIONNER DES DGTS PERMANENTS
AU MATRIEL.
IB70-8671
Livret d'instructions
En vigueur ds juillet 2008
1.2 Gnralits
Les commutateurs ATS sont utiliss pour protger les appareils
lectriques critiques (charge) contre toute perte de courant. La
charge alimente par la source de courant lectrique des services
publics (courant secteur) est protge par l'alimentation de secours de la gnratrice. Le commutateur ATS est reli aux deux
sources de courant et alimente la charge l'aide du courant de
l'une des deux sources. En cas de panne du courant secteur,
l'ATS transfre la charge sur la gnratrice. Ds la fin de la
panne, la charge est automatiquement relie de nouveau au rseau
de distribution lectrique (figure 2).
Gnratrice
Page 3
ATTENTION
NE TRANSFREZ PAS MANUELLEMENT LE COMMUTATEUR LORSQU'IL EST SOUS TENSION.
Courant secteur
Charge
Figure 2. Schma du commutateur (contacteur) de transfert de
charge type.
Un systme intelligent active le transfert lorsque le courant secteur est coup ou devient infrieur une tension prrgle. Un
dmarrage de moteur est alors activ par la gnratrice et l'ATS
transfre la charge vers le courant de la gnratrice lorsque ce
courant est disponible. Lorsque le courant secteur est rtabli,
l'ATS lui renvoie automatiquement la charge et la gnratrice
s'arrte aprs une temporisation. Au cas o, au moment d'une
panne de courant, le courant de la gnratrice n'apparat pas,
l'ATS reste branch au courant secteur jusqu' apparition du courant de la gnratrice. De mme, en cas de branchement la
gnratrice et si le courant secteur n'est pas disponible, l'ATS
reste branch la source de courant de la gnratrice.
L'ATS effectue automatiquement le transfert et comprend trois
lments de base:
1. les contacts principaux pour brancher et dbrancher la charge
de et vers la source de courant;
2. les solnodes pour effectuer le transfert des contacts principaux d'une source l'autre;
3. les circuits intelligents et de surveillance pour contrler de
faon constante l'tat des sources de courant et fournir
l'intelligence ncessaire pour le fonctionnement du commutateur et du circuit reli.
IB70-8671
Livret d'instructions
Page 4
100
Fabricant
Eaton
L 24
Type
Intensit
Commutateur nominale
de
gnratrice 100 = 100 A
Tableau
Centro
de de
carga
Type de botier
L24 - 24 circuits
R = Type 3R
distribution
Non branche
"Non branche" est utilis lorsque l'entre n'est pas en court-circuit avec un contact ou un branchement extrieur.
1.5 Glossaire
Dans le cadre de leur utilisation dans ce document, pour dcrire
des commutateurs de transfert et des commandes, les termes cidessous ont les dfinitions suivantes.
Disponible
Une source de courant est dfinie comme tant "disponible" lorsque sa tension est l'intrieur des valeurs de rglage pour la tension nominale prvue.
Branche
"Branche" est utilis lorsque l'entre est en court-circuit avec un
contact ou un branchement extrieur.
Panne de courant
Une source est considre comme tant en panne lorsque sa tension est l'extrieur des valeurs de rglage pour la tension nominale prvue et pour une dure dpassant de 0,5 seconde le point
d'expiration de la dure de temporisation d'urgence (TDEF).
Scurit intgre
Particularit qui empche la disjonction de la seule source de courant disponible et force galement une opration de transfert ou
de transfert inverse vers la source de courant disponible.
Transfert inverse
Changement du branchement de la charge de la gnratrice vers le
courant secteur.
Courant secteur
Principale source de courant, courant lectrique normal (des services publics).
Gnratrice
Source de courant secondaire (gnratrice de secours, source de
courant de secours, d'appoint ou de rserve).
IB70-8671
Livret d'instructions
En vigueur ds juillet 2008
Page 5
2.2 Manipulation
Comme indiqu prcdemment, le commutateur ATS est emball
sparment. Protgez le matriel des chocs en tout temps et
n'empilez pas les cartons l'un sur l'autre. Une fois que le matriel
est pied d'uvre et prt installer, le matriel d'emballage peut
tre retir. Voir la section 4 le mode d'installation.
2.3 Remisage
Bien qu'il soit bien emball, ce matriel ne convient pas un
remisage l'extrieur. Sa garantie devient nulle en cas de preuve
de remisage l'extrieur. S'il doit tre remis l'intrieur pendant
un certain temps, il faut le laisser dans son emballage de protection. Protgez en tout temps le matriel contre l'excs d'humidit,
la salet du chantier, les conditions de corrosion et autres corps
trangers. Nous suggrons fortement de remiser le matriel protg par son emballage dans une pice ambiance contrle,
entre -20 et 70 C (-4 et 158 F) et humidit relative de 80 %
ou moins. N'empilez jamais d'autre matriel, emball ou non, sur
l'emballage du botier de l'ATS.
Livret d'instructions
Page 6
Le RTC-50 est un ensemble de commande logique de commutateur de transfert microprocesseurs. Le matriel et le logiciel de
la commande contiennent les circuits intelligents et de surveillance
pour contrler de faon constante l'tat des sources de courant et
fournir l'intelligence ncessaire pour le fonctionnement de l'ATS
(fig. 5).
5J.
12.
Position du commutateur
Des voyants DEL indiquent la position du commutateur.
Disponibilit des sources de courant
Des voyants DEL indiquent si une source de courant est disponible. Ces voyants peuvent tre intgrs la commande
ou en tre spars.
12G. Courant secteur disponible
Si le voyant DEL vert est allum, cela indique que la source
de courant secteur est disponible.
26.
IB70-8671
Livret d'instructions
En vigueur ds juillet 2008
3.5 Normes
Le matriel ATS Eaton est class pour conformit UL. De plus, les
ATS Eaton sont classs au dossier E316586 par Underwriters
Laboratories, Inc. en vertu de la norme 1008 UL et UL 67. Cette
norme couvre les exigences pour les ATS dont on prvoit l'utilisation dans des lieux ordinaires afin de fournir l'clairage et l'lectricit dans les conditions suivantes :
a. Dans les circuits de secours, conformment l'article 702
du Code lectrique national.
Les ATS Eaton conviennent pour la norme 110 NFPA en matire
de circuits lectriques de secours.
Le matriel ATS Eaton est class pour conformit CSA. De plus,
les ATS Eaton sont classs au dossier Legacy LR96245 des contrats principaux 163545 par l'Association canadienne de normalisation, en vertu de la norme 22.2 no 178-1978.
Page 7
ATTENTION
AVANT DE METTRE LE COMMUTATEUR EN SERVICE, ASSUREZVOUS QUE L'CRAN ISOLANT EST BIEN INSTALL. CE DERNIER
PROTGE CONTRE LES TENSIONS DANGEREUSES AUX BORNES DE
COURANT ET DE CHARGE LORSQUE LE MATRIEL FONCTIONNE.
NE PAS VOUS EN ASSURER PEUT OCCASIONNER DES BLESSURES
CORPORELLES OU MORTELLES.
5.321
Choisissez un endroit o la surface est plate, rigide et peut supporter le poids du commutateur ATS dans son botier (voir fig. 6).
Protgez en tout temps le matriel contre l'excs d'humidit, la
poussire, la salet, la peluche et les vapeurs corrosives.
7.154
5.321
2.633
2.496
14.462
5.198
19.005
29.332
3.154
8.000
14.308
14.462
Figure 6. Dimensions et vue en plan d'EGS ordinaire (en po) (100 A) - Botier type 3R.
IB70-8671
Livret d'instructions
Page 8
MISE EN GARDE
LES CONDUCTEURS DE COURANT PEUVENT TRE SOUS TENSION
ET DONC OCCASIONNER DES BLESSURES CORPORELLES OU MORTELLES. DSEXCITEZ TOUS LES CONDUCTEURS DE COURANT OU
DE CIRCUIT DE COMMANDE RELIER AU COMMUTATEUR ATS
AVANT DE COMMENCER TOUT TRAVAIL SUR LES CONDUCTEURS
ET DE LES RELIER AU MATRIEL.
ATTENTION
ATTENTION
FAITES TRS ATTENTION PROTGER L'ATS CONTRE LES
BAVURES DE PERAGE, LA LIMAILLE ET AUTRES IMPURETS EN
CONFECTIONNANT LES OUVERTURES POUR LES CBLES ET EN
MONTANT LE BOTIER, AFIN D'VITER TOUS DGTS AUX PICES
ET TOUT DFAUT ULTRIEUR DE FONCTIONNEMENT.
AVISO
L'INSTALLATION DOIT TRE ENTIREMENT CONFORME AUX
CODES, NORMES ET RGLEMENTS APPLICABLES.
100
#14 2/0
ATTENTION
UN MAUVAIS RACCORDEMENT DU CBLE DE COURANT PEUT
OCCASIONNER UNE CHALEUR INTENSE ET LA PANNE SUBSQUENTE DU MATRIEL.
Remarque: Serrez les bornes des fils au couple indiqu sur l'tiquette fixe
sur le dos de la porte de l'ATS.
AVISO
POUR LE CBLAGE DE COMMANDE (DE DMARRAGE DU MOTEUR
DE LA GNRATRICE), LES CBLES DOIVENT TRE ISOLS DES
CBLES DES SOURCES DE COURANT SECTEUR ET DE LA GNRATRICE.
IB70-8671
Livret d'instructions
En vigueur ds juillet 2008
Page 9
BORNES DE
COURANT
SECTEUR
POINT NEUTRE
BORNES DE
COURANT
SECTEUR
BORNES DE
COURANT DE
GNRATRICE
BORNES DE
CHARGE
GENERATORTERRE
START TERMINALS
BORNES DE
COURANT DE
GNRATRICE
BORNES DE
CHARGE
IB70-8671
Livret d'instructions
Page 10
4.5 Cblage
MISE EN GARDE
LES CONDUCTEURS DE COURANT ET LE CBLAGE DE COMMANDE
PEUVENT TRE SOUS TENSION ET DONC OCCASIONNER DES
BLESSURES CORPORELLES OU MORTELLES. DSEXCITEZ TOUS
LES CONDUCTEURS DE COURANT OU DE CIRCUIT DE COMMANDE
AVANT D'EFFECTUER TOUTE OPRATION DE CBLAGE AUTOUR
OU SUR LE COMMUTATEUR ATS.
Charges
non critiques
Courant secteur
(source 1)
Watt-heuremtre
Panneau du
courant secteur
ATTENTION
VRIFIEZ LA TENSION NOMINALE SUR LA PLAQUE D'IDENTIFICATION DE L'ATS; ELLE DOIT TRE IDENTIQUE CELLES DU COURANT
SECTEUR ET DE LA GNRATRICE. UTILISER LE MATRIEL SUR UNE
TENSION INCORRECTE PEUT L'ENDOMMAGER.
Commutateur
de transfert
Gnratrice
(source 2)
Disjoncteur
(en gnral inclus
avec la gnratrice)
4.6 Installation
Dans une installation type pour charges critiques (voir fig. 10),
l'ATS (1) et la gnratrice (2) sont relis la source de courant.
L'ATS et le panneau de distribution du courant de secours (1)
reoivent le courant secteur partir d'un disjoncteur spcialis
dans le panneau du courant secteur (3). L'ATS et le panneau du
courant de secours reoivent le courant de la gnratrice partir
de la gnratrice (2). Le courant secteur alimente le panneau du
courant secteur.
Charges
critiques
Cblage
de commande
IB70-8671
Livret d'instructions
En vigueur ds juillet 2008
ATTENTION
SI LE MATRIEL N'EST PAS UTILIS LA TENSION VOULUE, VOUS
POURRIEZ L'ENDOMMAGER. N'ACTIONNEZ PAS LE MATRIEL SI
LES TENSIONS D'ALIMENTATION NE CORRESPONDENT PAS
L'TIQUETTE D'IDENTIFICATION.
4.9 Protection
Pour le no EGS100L24R seulement
Lorsque le commutateur de transfert est protg par l'un des disjoncteurs suivants dont l'intensit est infrieure 150 ampres, il
peut tre utilis sur un circuit capable d'alimenter un courant maximal de 240 volts, avec un maximum de 25 000 ampres
symtriques de valeur efficace, mais pas infrieur la capacit
d'interruption du disjoncteur choisi.
Eaton/Cutler-Hammer
BR
CH
FDC
BW
BWH
Siemens
CED6 ED6
ED4
CSR
HED6
CSH
HED4
Page 11
MISE EN GARDE
VOUS TES PRT METTRE LE MATRIEL SOUS TENSION. LES
TENSIONS L'INTRIEUR DU BOTIER PEUVENT OCCASIONNER
DES BLESSURES CORPORELLES OU MORTELLES. FAITES TRS
ATTENTION POUR VITER TOUT CONTACT AVEC LE MATRIEL
SOUS TENSION.
MISE EN GARDE
TOUT CONTACT AVEC DES PICES SOUS TENSION PEUT
ENTRANER UN CHOC LECTRIQUE ET OCCASIONNER DES
BLESSURES CORPORELLES OU MORTELLES. FAITES TRS ATTENTION POUR VITER TOUT CONTACT AVEC LES PICES SOUS TENSION LORSQUE VOUS UTILISEZ UN VOLTMTRE.
AVISO
CECI STIMULE UNE INTERRUPTION DE LA SOURCE DE COURANT
SECTEUR.
tape 2: Aprs une temporisation (selon le rglage de la gnratrice), le moteur de la gnratrice de secours dmarre.
tape 3: l'aide d'un voltmtre, mesurez les tensions de ligne
ligne et de ligne au point neutre aux bornes de la ligne de
courant de gnratrice pour vous assurer que sa tension
est correcte. Au besoin, ajustez le rgulateur de tension
de la gnratrice selon les recommandations du fabricant
afin de corriger toute dviation de tension. L'ATS ne
rpond qu' la tension correcte en provenance de la
gnrarice.
tape 4: Fermez le disjoncteur de courant de la gnratrice en
amont ou le commutateur pour relier l'ATS la tension
de la source de courant de gnratrice.
IB70-8671
Livret d'instructions
Page 12
SECTION 6: RGLAGES
6.1 Gnralits
Pour connatre les rglages et les fonctions de la commande
RTC-50, rfrez-vous au document IB00405004E-70-8664 fourni
avec l'ATS.
tape 7: La temporisation de secours (gnratrice) normal (courant secteur) (TDEN) de l'ATS dbute, le solnode
s'engage et le contacteur commute automatiquement de
la position GENERATOR la position UTILITY. La
gnratrice s'arrte aprs une priode de refroidissement
du moteur.
IB70-8671
Livret d'instructions
En vigueur ds juillet 2008
MISE EN GARDE
DES TENSIONS LEVES SONT PRSENTES DANS ET AUTOUR DU
COMMUTATEUR DE TRANSFERT. AVANT TOUTE INSPECTION OU
TOUT ENTRETIEN DE CE MATRIEL, DBRANCHEZ LE COURANT
SECTEUR DU MATRIEL RPARER EN OUVRANT, ET EN VERROUILLANT SI POSSIBLE, LE DISJONCTEUR SUIVANT LE PLUS EN
AMONT. SINON, VOUS POURRIEZ OCCASIONNER DES BLESSURES
CORPORELLES GRAVES OU MORTELLES.
Page 13
MCANISME DE TRANSFERT
TENSION DALIMENTATION
DE LA GNRATRICE
PANNEAU DE DISTRIBUTION
PRINCIPAL (CHARGE))
COMMANDE DE COMMUTATEUR
DE TRANSFERT RTC-50
REMISE ZRO
ENTRETIEN
INDICATEUR
DENTRETIEN
DTECTION
DBRANCHEMENT
DE CHARGE
DBRANCHEMENT
DE CHARGE
SOURCE 1 - FERM
SOURCE 2 - FERM
Figure 12. Schma de cblage pour l'ATS EGS100L24R (illustr hors tension).
IB70-8671
ALIMENTATION DU COURANT
SECTEUR - C.A. DE 240 V
Livret d'instructions
Page 14
7.2 Procdures
Le tableau 3 prsente des procdures d'entretien suggres.
ACTION
Inspectez la zone, surtout l o le contacteur est install, la recherche de dangers pour la scurit, personnelle ou incendie. L'exposition certaines vapeurs chimiques peut dtriorer les raccords lectriques.
Recherchez les accumulations de salet, les pices desserres ou les dgts physiques.
Examinez l'isolant primaire la recherche de fissures ou de surchauffe. La surchauffe se manifeste sous forme de dcoloration, de matriau fondu, de formation de cloques sur la gaine isolante
ou de piqres ou de fusion des surfaces du conducteur due aux tincelles.
Inspectez les raccords de commande secondaire la recherche de dgts et le cblage de commande pour vrifier le bon tat de l'isolant.
c. Inspectez le contacteur la recherche de poussire, de salet, de suie, de graisse, d'humidit ou liminez la poussire, la salet, la suie, la graisse, l'humidit et la corrosion des surfaces du comde corrosion.
mutateur l'aide d'un chiffon souple, sec et sans peluche, d'une brosse poils doux et secs et d'un
aspirateur. Ne soufflez pas les dbris l'intrieur du contacteur. En cas de prsence de corps
trangers, dcouvrez-en la source et liminez-la.
d. Vrifiez l'intgrit du matriel et recherchez l'usure ingale, la dcoloration ou les pices desserres. En cas de fissuration importante, remplacez les pices; les pices de fixation desserres doivent
tre resserres.
e. Vrifiez les bornes et les raccords la recherche de desserrage ou de traces de surchauffe.
La surchauffe se repre la dcoloration, la fusion ou aux cloques sur l'isolant des conducteurs.
Ne touchez pas aux raccords qui ne prsentent aucun signe de desserrage ou de surchauffe.
f. Actionnez le contacteur s'il ne sert pas souvent; ceci permet de garder en bon tat l'action de
glissement des contacts.
Si un commutateur est souvent utilis pendant le fonctionnement normal du matriel, cette tape
n'est pas indispensable.
Assurez-vous que tous les crans de protection sont en place et que la porte est ferme. Remettez
en service le courant secteur et de la gnratrice.
IB70-8671
Livret d'instructions
Mode d'emploi et d'entretien du commutateur de transfert
automatique EGS commande RTC-50 et tableau de
distribution intgr - 100 Amp
ACTION
Exemple: 01/01/04
Inspection et nettoyage.
IB70-8671
Page 15
Livret d'instructions
Page 16
NUMRO DE PICE
Contacteur
99-5638
MODLE ATSL
100 A
Commande RTC-50
RTC50
100 A
Faisceau EGS
99-5638-3
100 A
99-5638-4
100 A
99-5638-15
100 A
Bornes
99-5638-6
100 A
99-5638-17
100 A
Dispositif SurgeTel
DHW4PT
100 A
DCXCAP2
100 A
TVSS
99-5638-10
100 A
MISE EN GARDE
RTC-50
COMMANDE
AVISO
APRS REMPLACEMENT DE LA PICE, REPLACEZ EN CIRCUIT LE
COURANT SECTEUR (SOURCE 1) ET PLACEZ LE SLECTEUR DE LA
GNRATRICE SUR LA POSITION AUTO. VRIFIEZ LE BON FONCTIONNEMENT DU SYSTME.
IB70-8671
Livret d'instructions
En vigueur ds juillet 2008
Page 17
tape 2: Dbranchez les fiches J1, J2, J3, J4 et J6 de la commande (voir fig. 14).
tape 3: Dbranchez les fils relis aux prises J7 et J8.
tape 4: Dposez les quatre (4) vis situes aux coins de la commande pour la fixer sur le panneau lectrique. Dposez la
commande (fig. 14).
PRISES
J1 J4
BARRES DE
POINT NEUTRE
VIS DE
MONTAGE
tape 3: Dposez les deux vis du socle noir l'aide d'un tournevis
lame plate ou d'une douille ou d'un tourne-crou de
0,375 po. Dposez la bande de prise de terre l'aide
d'un tournevis lame plate puis dposez la barre de
point neutre.
DES VIS
Figure 14. Dpose du panneau de la commande.
tape 5: Alignez la nouvelle commande sur les trous de montage.
Fixez le nouveau panneau de la commande l'aide des
pices de fixation existantes. Serrez les vis.
tape 6: Branchez les fiches J1, J2, J3, J4 et J6 sur leurs prises
respectives.
tape 7: Branchez les fils relis aux prises J7 et J8.
tape 8: Replacez sous tension le commutateur de transfert.
tape 9: Aprs remplacement de la commande, placez le slecteur
de la gnratrice sur la position AUTO. (La gnratrice
peut dmarrer mais s'arrtera dans les 5 minutes.) Vrifiez le bon fonctionnement du systme.
IB70-8671
Livret d'instructions
Page 18
N1
E1
N2
E2
INTERRUPTEUR AUX.
DE COURANT SECTEUR
BOBINE DU
COURANT SECTEUR
INTERRUPTEUR AUX.
DE GNRATRICE
BOBINE DE
GNRATRICE
VIS DE
MONTAGE
Figure 17.
BORNE DE
PRISE DE TERRE
IB70-8671
Livret d'instructions
En vigueur ds juillet 2008
Page 19
BORNES DU
COURANT
SECTEUR
BORNES DE
GNRATRICE
N1
N2
E1
E2
BORNES DE CHARGE
Figure 21. Remplacement des bornes de 100 A.
tape 1: Avant de remplacer les bornes, coupez le courant secteur
(source 1) et placez le slecteur de la gnratrice (source
2) sur la position OFF.
tape 2: Dconnectez tous les cbles du connecteur.
tape 3: Reprez leur emplacement puis dconnectez les douze
(12) fils rouges du contacteur (voir fig. 18).
CONTACT
RACCORDS DE
AUX. N. F. DE
RACCORDS DE
LA BOBINE DU
COURANT
BOBINE DE
COURANT
CONTACT
SECTEUR
GNRATRICE
AUX. N.F. DE
SECTEUR
GNRATRICE
COM. AUX.
COM. AUX. DE
DE COURANT
GNRATRICE
SECTEUR
IB70-8671
Livret d'instructions
Page 20
Rptez l'opration pour la deuxime borne de gnratrice. Assurez-vous de ne laisser aucun jeu entre les
bornes et la barre.
tape 9: Fixez les bornes de charge la barre omnibus de charge
l'aide des pices de fixation fournies.
Remarque: Les bornes de charge ne ncessitent pas de cosses
de fil de commande.
tape 10: Fixez le contacteur la plaque de base l'aide des quatre (4) vis fournies.
Pour les SE ATSs
tape 11: Reliez les fils rouges au contacteur. Examinez chaque
fil pour en reprer le nom et voyez sur la fig. 21 les
points de connexion corrects.
tape 12: Reliez tous les cbles au contacteur leurs points de
connexion d'origine.
tape 13: Aprs remplacement des bornes, replacez en circuit le
courant secteur (source 1) et placez le slecteur de la
gnratrice sur la position AUTO. Vrifiez le bon fonctionnement du systme.
7.5 Troubleshooting
Le tableau 5 prsente le mode de dpannage de l'ATS EGS. Si un
problme persiste aprs avoir effectu le dpannage ci-dessous,
contactez un reprsentant des ventes Eaton agr.
CAUSE
CORRECTION
Le commutateur de transfert automatique ne met pas la gnratrice en service. 1. Le disjoncteur de la gnratrice est ouvert.
2. La tension de la gnratrice n'est pas acceptable.
Le commutateur de transfert automatique ne met pas le courant secteur en ser- 1. Le disjoncteur du courant secteur ouvert.
vice.
2. La tension du courant secteur n'est pas acceptable.
La gnratrice reste en circuit alors que le commutateur a mis le courant secteur en service.
IB70-8671
Livret d'instructions
Mode d'emploi et d'entretien du commutateur de transfert
automatique EGS commande RTC-50 et tableau de
distribution intgr - 100 Amp
Remarques:
IB70-8671
Page 21
Livret d'instructions
Page 22
Remarques:
IB70-8671
Livret d'instructions
Mode d'emploi et d'entretien du commutateur de transfert
automatique EGS commande RTC-50 et tableau de
distribution intgr - 100 Amp
Remarques:
IB70-8671
Page 23
Livret d'instructionst
Page 24
Eaton Corporation
Electrical Group
1000 Cherrington Parkway
Moon Township, PA 15108
tats-Unis
877-ETN CARE (877-386-2273)
www.Eaton.com