Вы находитесь на странице: 1из 6

(Screw Thread, Nut Bolt, Locking Devices, Bearings, Studs & Composite Material)

Q. 1
Q. 2
Q. 3
Q. 4

Q. 5

Q. 6
Q. 7
Q. 8
Q. 9
Q. 10
Q. 11
Q. 12
Q. 13
Q. 14
Q. 15

Steel can be classified as


(a) Straight carbon steel
(b) Alloy steel
(c) Both (a) and (b)*
The steel which doesn't contain enough carbon to cause hardening when heated termed as
(a) Low carbon steel*
(b) Medium carbon steel
(c) High carbon steel
(d) All of the above
The steel which contain chromium, nickel etc in addition to carbon and iron is termed as
(a) Mild steel
(b) Corrosion resistant steel
(c) Alloy steel*
(d) None
During Brinell testing of ferrous metal, a pressure of 3000 Kg is applied on the specimen for
the period of
(a) 10 seconds *
(b) 30 seconds
(c) 30 minutes
(d) 10 minutes
When testing non-ferrous metal by Brinell method a pressure of 500 Kg is applied on a part
for the period of
(a) 10 seconds
(b) 20 seconds
(c) 30 seconds*
(d) 10 minutes
The Brinell tester uses a hardened spherical ball having a diameter of
(a) 5 mm
(b) 10 mm*
(c) 15 mm
(d) 10 inch
Aluminum stands in the scale of maleability
(a) First
(b) Second *
(c) Third
Induclity scale aluminum stands (a) Sixth*
(b) Seventh
(d) First
Composite material is used to make power plant as well as ______ designs
(a) Skin
(b) Airframe*
(c) Structure
(d) None
How many types of fibres are used in composite material
(a) Fiber glass
(b) Aramid
(c) Carbon / Graphite
(d) All are correct *
What is role of matrix in composite material which may
(a) serve as bonding*
(b) contacting
(c) attaching
(d) none
One of the most popular fibres is used in composite material i.e.
(a) Aramid
(b) Carbon
(c) Fiber glass *
(d) All
Sealing compounds is used to(a) To prevent leakage of fuel.
(b) To prevent passages of fumes
(c) To prevent corrosion
(d) All*
One-part sealant is prepared by(a) Manufacturer*
(b) User
(c) Both (a) and (b)
(d) Either (a) or (b)
What is working life of mixed sealants from ............ hours
(a) 1

1
to 4 hours*
2

(b) 2 to 4 hours

(c) 01 to 3 hours
(d) None of the above
Q. 16 Types of damage occur when a foreign object strikes the part
(a) Cosmetic defects
(b) Impact damage*
(c) Delamination
Q. 17 Which will not come under types of defects
(a) cracks
(b) Hole damage
(c) Lamination*
Q. 18 Surface wrinkles or separation between ply & release paper comes under which type of
defects
(a) In service defects
(b) Prepreg defects *
(c) Environmental defects
Q. 19 Repair methods are applied for different materials are given in (a) Maintenance manual
(b) Structural repair manual*

(c) QC manual
Q. 20 Which inspection is used for internal damage
(a) Coin tap test
(b) Visual inspection
(c) Ultrasonic inspection *
Q. 21 What is appearance of the corrosion on aluminum & magnesium
(a) White powered deposit *
(b) Greenish film
(c) Reddish deposit
(d) None of the above
Q. 22 On copper and copper alloy the corrosion form is a _____________
(a) Reddish rust
(b) Greenish film *
(c) Greenish white
(d) None
Q. 23 The form of corrosion on steel is _________
(a) Greenish film
(b) Reddish rust *
(c) White powdered
Q. 24 What are most common agents causing direct chemical attack
(a) Spilled battery acid or fumes of batteries
(b) Residual flux deposited
(c) Entrapped caustic cleaning solution
(d) All of the above *
Q. 25 Fretting corrosion is also known as
(a) False brinelling *
(b) True brinelling
(c) Rubbing
Q. 26 What types of structural sections are more susceptible to corrosion attack
(a) Thin
(b) Fat
(c) Thick *
Q. 27 What are areas where susceptibility to corrosion is more
(a) Exhaust trail
(b) Battery compartment
(c) Wheel well
(d) All *
Q. 28 The bottom surface joining the sides of two adjacent threads is known
(a) Crest
(b) Root *
(c) Helix angle
Q. 29 The lenght of contact between two meting parts measured axially is called
(a) No. of threads
(b) Depth of threads
(c) Length of engagement*
Q. 30 It is the minimum clearance or maximum interferance when intended between mating parts
is said
(a) Tolerance
(b) Clearance
(c) Allowance *
Q. 31 Screw threads are used as
(a) Means of joining metal parts
(b) Assembling & dis-assembling the metal parts without damage
(c) Used to obtain measurements in thin ten thousands of an inch
(d) All above*
Q. 32 Threads used by watch makers and instruments maker for very small screw is(a) ACME thread
(b) Buttress thread
(c) V thread*
Q. 33 A thread which is a modification of square thread is called(a) Buttress thread
(b) acme thread*
(c) V thread
Q. 34 The angle of acme thread is
(a) 300
(a) 280
0
(a) 25
(d) 290*
Q. 35 In single start thread the pitch and lead are __________
(a) Double
(b) Single
(c) Equal *
Q. 36 In multi start thread formula for calculation of lead is _______
(a) Pitch No. of start *
(b) Lead No. of pitch
(c) Lead No. of start
Q. 37 Class II fit is known as (a) loose fit
(b) close fit
(c) medium fit
(d) Free fit*
Q. 38 Class-3 fit called (a) Medium fit*
(b) loose fit
(c) close fit
Q. 39 1-14 NF, N 0.14 indicates
(a) No. 14 of TPI*
(b) No. in lead
(c) None

Q. 40 A 4-28 thread indicates that inch di(a) bolt has ____ thread in a inch
(a) 28*
(b) 28 dia
(c) both (a) & (b) correct
Q. 41 Aircraft screws are manufactured with a ____ thread fit in case of assembly.
(a) Class 1
(b) Class 3
(c) Class 2*
Q. 42 Special bolts are usually identified by the letter ______ stamped on the hea(d)
(a) N
(b) M
(c) S*
Q. 43 AN bolts come in the following head styles (a) Hex head
(b) Clevis
(c) Eyebolt
(d) all the above*
Q. 44 MS bolts come in hex-head and ____ styles.
(a) internal-wrenching*
(b) External wrenching
(c) Nither (a) nor (b) correct
Q. 45 How much permissible clearance for a 5/8" hole is required
(a) 0.002"
(b) 0.004"
(c) 0.006"*
Q. 46 Alloy steel bolts smaller than _____ are not used for primary structure.
(a) No - 10-15
(b) No - 10-32*
(c) No - 15-25
Q. 47 A boltof aluminum which is smaller than _____ dia is not used for primary structure.
(a) 1/8"
(b) 1/4"*
(c) 5/8"
Q. 48 The material recommended for wire locking are
(a) corrosion resisting steel
(b) heat resisting nickel alloy
(c) Both (a) and (b)*
(d) None of the above
Q. 49 While locking the nut with the locking wire, the wire must be applied
(a) So that all pull exerted by the wire tends to tighten the nut.*
(b) So that the locking wire should not break.
(c) Both (a) and (b)
(d) None of the above
Q. 50 The purpose of locking device is
(a) to prevent loosening or disengagement of mating components
(b) Its effective ness may be of utmost Importance to the safety of An A/C
(c) Both (a) and (b)*
(d) None of the above
Q. 51 Tab washers are manufactured from
(a) Thin metallic sheet materials*
(b) Light materials
(c) Both (a) and (b)
(d) None of the above
Q. 52 In Tab washer, The Tab should not be bent
(a) More than once*
(b) More than twice
(c) Until unless it is not broken
(d) All are correct
Q. 53 Spring washer should be renewed
(a) During overhaul
(b) During repair
(c) Renewal is not necessary
(d) Both (a) and (b)*
Q. 54 Locking plates are manufactured from
(a) Steel*
(b) Spring steel
(c) Nickel steel
(d) All above are correct
Q. 55 Locking plates may be used
(a) repeatedly
(b) once
(c) more than one if condition of locking plate is satisfactory
(d) both (a) and (c)*
Q. 56 While locking the component with locking wire, the angle of approach of the wire
(a) should not be less than 450 to the rotational axis of the component to be locked*
(b) should not be more than 450 to the rotational axis of the component to be locked
(c) should not be less than 900 to the rotational axis of the component to be locked
(d) None of the above
Q. 57 For securing cow lings and fairings the fasteners are used
(a) Camloc fasteners*
(b) DZUS fasteners
(c) Air lock fasteners
(d) None of the above
Q. 58 The material of crosspin in Air lock fastener is
(a) chrome vanadium steel
(b) heat treated steel
(c) both (a) and (b)*
(d) high carbon steel heat treated

Q. 59 The purpose of Grommet in DZUS lock fasteners is


(a) acts as a holding device for a stud*
(b) acts as a holding device for the spring
(c) both (a) and (b)
(d) None of the above
Q. 60 Prior to Initial Installation of tubing, All tubing should be pressure tested and withstand
(a) several times the normal operating pressure to which it will be subjected*
(b) with normal operating pressure to which it will be subjected
(c) Three times the normal operating pressure to which it will be subjected
(d) None of the above
Q. 61 External brake lines should always be made of corrosion resistant steel to minimize
(a) damage from rocks thrown by the tires during take off
(b) damage from rocks thrown by the tires during take off and landing*
(c) both (a) and (b)
(d) None of the above
Q. 62 Rubber Hose is suitable for use in
(a) Fuel, oil, coolant
(b) Fuel, oil, coolant and hydraulic systems*
(c) oil and fuel systems
(d) None of the above
Q. 63 Lines conveying fuel may be marked with letter
(a) TOXIC
(b) FLAME*
(c) PHDAN
Q. 64 In proof testing of flexible hose, the proof test pressures should be maintained for
(a) At least 30 seconds*
(b) At least 20 seconds
(c) At least 60 seconds
(d) At least 2 hrs.
Q. 65 In plumbing connectors. All AN Fittings are coloured
(a) Black*
(b) Blue
(c) not coloured
(d) None of the above
Q. 66 In Plumbing system, the AN 819 sleeve is used with the(a) AN 818 coupling nut*
(b) AN 818 nut.
(c) AN 819 coupling nut
(d) None of the above
Q. 67 In tube forming processes, A new piece of tubing should be cut
(a) Approximately 10 percent longer than the tube to be replaced*
(b) Approximately 10 percent shorter than the tube to be replaced
(c) Either (a) or (b)
(d) None of the above
Q. 68 While Tube cutting processes, if tubing of hard material is to be cut with a
(a) Fine tooth hacksaw
(b) Tube Cutter
(c) Fine tooth hacksaw having 32 teeth per inch*
(d) Hand bending
Q. 69 Purpose of Double Flare is
(a) The double Flare is smoother and more concentric than the single flare
(b) Double Flare seals better than single Flare
(c) Double Flare is more resistant to the shearing effect of torque
(d) All above are correct*
Q. 70 Rubber cushioned clamp is used to
(a) secure lines subject to vibration*
(b) secure lines where the deteriorating effect of hydraulic oil is effected
(c) secure lines in areas not subject to vibration
(d) None of the above
Q. 71 In assembly of sleeve type fitting, mark the hose position around the hose at the near of the
socket using a
(a) Grease pencil
(b) Painted line
(c) Both (a) and (b)*
(d) None of the above
Q. 72 The bearings are manufactured to a high degree of accuracy and finish are known as
(a) Instrument precision bearing *
(b) Thrust bearing
(c) Angular contact bearing
(d) All of the above
Q. 73 Cylindrical roller bearings are capable of carrying greater radial loads than ball bearings
because
(a) Of greater contact area of the rolling elements*
(b) Of lesser contact area of the rolling elements
(c) Movement is oscillatory

(d) None of the above


Q. 74 The bearings in which the length of the rollers is several times greater than their diameter
are
(a) Cylindrical roller bearing
(b) Needle roller bearing*
(c) Tapered roller bearing
(d) None of the above
Q. 75 In control rod ends the bearings are used
(a) Cylindrical roller bearing
(b) Needle bearing *
(c) Thrust bearing
(d) Tapered roller bearing
Q. 76 The Needle bearings are subjected to brinelling due to
(a) Lack of rotational movement *
(b) Lack of oscillatory movement
(c) Lack of lubricant
(d) None of the above
Q. 77 Bearings are classified by the
(a) Type of rolling element used *
(b) Loading capacity of the bearing
(c) Construction of bearing
(d) None of the above
Q. 78 Bearings which accept both radial load and axial load are
(a) Ball bearing
(b) Tapered roller bearing
(c) Both (a) and (b)*
(d) Roller bearing
Q. 79 In radial ball bearing the number of ball increases
(a) Increases the radial load capacity *
(b) Increases the axial load capacity
(c) Both (a) and (b)
(d) None of the above
Q. 80 Bearings capable of accepting radial loads and axial loads in one direction are known as
(a) Angular contact bearing *
(b) Radial ball bearing
(c) Thrust bearing
(d) None of the above
Q. 81 The axial loading capacity of an angular contact bearing depends
(a) On the contact angle *
(b) On the number of balls
(c) On the outer ring
(d) None of the above
Q. 82 The bearing are designed for axial loading only and are normally used in conjunction with a
roller bearing is known as
(a) Thrust bearings *
(b) Instrument precision bearings
(c) Angular contact bearings
(d) None of the above
Q. 83 The bearing are designed that the axes of the rollers form an angle with the shaft axis are
known as
(a) Spherical roller bearings
(b) Tapered roller bearing*
(c) Needle bearing
(d) None of the above
Q. 84 The bearing is capable of with standing heavy radial loads and moderate axial loads from
either direction is known as
(a) Tapered roller bearing
(b) Spherical roller bearing *
(c) Cylindrical roller bearing
(d) None of the above
Q. 85 The majority of bearing failures are caused by(a) Faulty Installation
(b) Unsatisfactory lubrication
(c) In adequate protection against the entry of liquids, dirt or grit
(d) All above are correct*
Q. 86 The material of bearings where temperature is above 800oF (427oC) or below where lubricant
is not permitted(a) Cast or wrought cobalt alloys*
(b) Steel
(c) Cast alloys
(d) Wrought cobalt alloys
Q. 87 Bearings which are to be stored should be
(a) Dipped in rust preventive oil
(b) Wrapped in grease proof paper
(c) Suitably boxed and labelled
(d) All of the above *
Q. 88 The bearings which are stored for a period of one year should be
(a) Inspected for corrosion
(b) As In (a) and reprotected *
(c) Inspection is not required
(d) None of the above
Q. 89 Bearings are marked in some wayto indicate the class of fits
(a) System of dots
(b) As (a) and circle
(c) As (b) and letter
(d) All of the above*
Q. 90 The bearings have the smallest radial internal clerance and are normally used in precision
work are
(a) Group 2 bearings *
(b) Group 3 bearings
(c) Normal group of bearings
(d) Group 4 bearings
Q. 91 The group 2 bearing should not be used where
(a) Operating condition could reduce intenal clerances

Q.
Q.

Q.
Q.

Q.

Q.

Q.

Q.

Q.

(b) Not suitable for use as thrust bearings


(c) Not suitable for high speed
(d) All of the above *
92 To remove any remaining grease or dirt, the bearing should be soaked in
(a) White spirit*
(b) Petrol
(c) Avition turbine fuel
(d) None of the above
93 In gear system, the portioin of the tooth that projects above or outside of the pitch circle is
known as
(a) Dedendum
(b) Addendum*
(c) pitch diameter
(d) None of the above
94 The dedendum of a gear tooth is
(a) Addendum + clearance*
(b) Addendum
(c) Addendum Clearance
(d) None of the above
95 When Installing a turn buckle in a control system. It is necessary
(a) To screw both of the terminals to an equal number of turns in to the barrel.*
(b) To screw one of the terminals
(c) All turn buckle terminals be screwed in to the barrel until not more than two threads are
exposed
(d) None of the above
96 Once the doubler plate has been cured and the edges have been sealed the repair area can
be sealed and
(a) Painted to match the surrounding area *
(b) Sanded to match the surrounding area
(c) Both (a) and (b) are correct
97 MTCS: Lightning protection
(a) Al is used to provide conductive path for dissipation of electrical energy through static
wicks
(b) Since composite do not conduct electricity, lightning protection built in component
(c) If no protection means made, resin will evaporate
(d) As in (a), (b), (c) lightning indication is dark, brown or black spots or smudges that
appear to be heated*
98 The type of lightning protection needed may be one of the following
(a) A top layer of material in which fibre glass and Al wires woven together and top layer of
thin Al is bonded or sprayed
(b) A very fine screen or mesh made of Al or copper bonded under top layer
(c) A bonding strap from composite component to an Al structure
(d) Any one method can be used regardless of manufactures A/C *
99 MTCS: Gel coat is
(a) Polyester resin used during manufacturing
(b) On outside the surface provide smooth finish but not structural
(c) It cant be rejuvenated as dope on fabric can
(d) All *
100 If internal de-lamination is sufficiently minor can be repaired by
(a) Injecting resin into the cavity formed by ply separation
(b) Injecting resin fills the area and reattaches the skin
(c) Both (a) and (b) *

Вам также может понравиться