Академический Документы
Профессиональный Документы
Культура Документы
Manual Rev.:
2.04
Revision Date:
Part No:
50-13060-1030
Revision History
Revision
Release Date
Description of Change(s)
2.00
2008/08/29
Initial release
2.01
2008/10/29
2.02
2009/05/13
2.03
2010/07/03
2.04
2011/04/26
NuPRO-935A
Preface
Copyright 2008-2011 ADLINK Technology Inc.
This document contains proprietary information protected by copyright. All rights are reserved. No part of this manual may be reproduced by any mechanical, electronic, or other means in any form
without prior written permission of the manufacturer.
Disclaimer
The information in this document is subject to change without prior
notice in order to improve reliability, design, and function and does
not represent a commitment on the part of the manufacturer.
In no event will the manufacturer be liable for direct, indirect, special, incidental, or consequential damages arising out of the use or
inability to use the product or documentation, even if advised of
the possibility of such damages.
Environmental Responsibility
ADLINK is committed to fulfill its social responsibility to global
environmental preservation through compliance with the European Union's Restriction of Hazardous Substances (RoHS) directive and Waste Electrical and Electronic Equipment (WEEE)
directive. Environmental protection is a top priority for ADLINK.
We have enforced measures to ensure that our products, manufacturing processes, components, and raw materials have as little
impact on the environment as possible. When products are at their
end of life, our customers are encouraged to dispose of them in
accordance with the product disposal and/or recovery programs
prescribed by their nation or company.
Trademarks
Product names mentioned herein are used for identification purposes only and may be trademarks and/or registered trademarks
of their respective companies.
Preface
iii
iv
Preface
NuPRO-935A
Conventions
Take note of the following conventions used throughout this
manual to make sure that users perform certain tasks and
instructions properly.
CAUTION:
WARNING:
Preface
Information to prevent minor physical injury, component damage, data loss, and/or program corruption when trying to complete a task.
vi
Preface
NuPRO-935A
Table of Contents
Revision History...................................................................... ii
Preface .................................................................................... iii
List of Figures ........................................................................ xi
List of Tables........................................................................ xiii
1 Introduction ........................................................................ 1
1.1
Overview.............................................................................. 1
1.2
Features............................................................................... 1
1.3
Specifications....................................................................... 2
1.4
1.5
1.6
1.7
1.8
1.9
2.2
2.3
2.4
Jumpers ............................................................................. 25
3.2
3.3
3.4
Table of Contents
vii
4 Driver Installation.............................................................. 37
4.1
4.2
Display Driver..................................................................... 38
4.3
4.4
ISA Driver........................................................................... 39
4.5
TPM Driver......................................................................... 39
4.6
5.2
Main Setup......................................................................... 45
5.3
5.4
5.5
5.6
5.7
Security Setup.................................................................... 64
Chipset Setup .................................................................... 67
5.7.1 South Bridge Configuration............................................ 68
5.7.2 Advanced Chipset Settings............................................ 69
5.8
viii
Table of Contents
NuPRO-935A
B.2
B.3
IO Map ............................................................................... 79
B.4
Table of Contents
ix
Table of Contents
NuPRO-935A
List of Figures
Figure 1-1:
Figure 1-2:
Figure 2-1:
Figure 2-2:
Figure 2-3:
List of Figures
xi
xii
List of Figures
NuPRO-935A
List of Tables
Table
Table
Table
Table
Table
Table
Table
Table
1-1:
B-1:
B-2:
B-3:
B-4:
B-5:
B-6:
B-7:
List of Tables
xiii
xiv
List of Tables
NuPRO-935A
Introduction
1.1 Overview
The ADLINK NuPRO-935A is a PICMG 1.0 industrial SBC
supporting the next-generation Intel Core 2 Quad/Duo and Intel
Celeron processors in the LGA775 package to deliver a high
performance platform for a wide array of industrial automation
applications. The NuPRO-935A supports processing speeds up to
3.0 GHz and high-bandwidth network connectivity with PCI
Express-based gigabit LAN.
These advanced features, coupled with a dual-channel DDR2 system memory architecture and diverse I/O storage make the
NuPRO-935A suitable for industrial automation and automation
control applications requiring a standardize, easy-to-deploy, and
cost-effective SBC.
1.2 Features
X
RoHS compliant
Introduction
1.3 Specifications
System
CPU/Cache
FSB
800/1066/1333 MHz
Chipset
Memory
BIOS
Audio
Hardware
Monitor
TPM
IDE
Serial ATA
I/O Ports
ISA
NOTE:
Introduction
NuPRO-935A
VGA
Display
GMA 3100 integrated in Q35 GMCH
VRAM
CRT
Controller
Ports
Form Factor
Dimensions
338 x 122 mm (L x W)
Operating Temp.
0C to 60C
Storage Temp.
-20C to 80C
Relative Humidity
Safety
Introduction
Memory
Graphics
SATA Channel
Power Supply
DOS (idle)
Power Req.
+5V
+12V
CPU +12V
Total
Current (A)
3.37A
367.9mA
3.24A
Watts (W)
16.87W
4.42W
38.88
60.17W
+5V
+12V
CPU +12V
Total
Current (A)
3.203A
233,6mA
1.578A
Watts (W)
16.02W
2.80W
18.94W
37.76W
Power Req.
+5V
+12V
Current (A)
3.276A
533.0mA
7.616A
Watts (W)
16.38W
6.4W
91.39W
114.17W
Total
Power Req.
+5V
+12V
CPU +12V
Total
Current (A)
3.708A
555.1mA
5.728A
Watts (W)
18.54W
6.66W
68.74W
93.94W
Introduction
NuPRO-935A
CPU
Core2 Quad/Duo
Celeron
LGA775 package
800/1066/1333 MHz FSB
Dual-Core
Hyper-Threading
800/1066/1333 MHz
FSB
Northbridge
DDR Channel A
CRT
DIMM x2
DB-15
DDR Channel B
DMI
Interface
2 GB/s
Southbridge
PCIe
Controller
SATA
SATA ports x2
USB 2.0
(Bracket x1, Internal x4)
USB 2.0
LPC
TPM
(DV only)
RS-232
Intel 82566DM
RJ-45
PCIe x1
Intel 82573L
RJ-45 (DV only)
SPI
HD
Codec
PCI Bus
PCI 32-bit/
33MHz bus
IT8888G
ISA Bridge
ISA bus
PCI
Controller
Header for
DB-Audio2
KB/Mouse
LPT/FDD
PCIe x1
Intel ICH9
JMicron JMB20330
SATA to IDE Controller
SPI BIOS
ITE8718
LPC Super I/O
Hardware
Monitor
RS-232/
422/485/
485+
Introduction
Introduction
NuPRO-935A
Gigabit Ethernet
The NuPRO-935A uses two Gigabit Ethernet controllers (Intel
82566DM, 82573L) connected to the PCI-E x1 bus of the ICH9.
82566DM is a single port Gigabit Ethernet Physical Layer Transceiver (PHY) that connects to its MAC through a dedicated interconnects. Both 82566DM and 82573L support operation at data
rates of 10/100/1000 Mbps. Utilizing its wide bandwidth, the Gigabit LAN controller allows up to 1 Gbps of data transfer rate for
superior network communications.
Hardware monitoring
A built-in, proactive hardware monitoring system in the ASIC monitors the CPU temperature, system fan rotations, and voltage levels to prevent overheating and/or component damage, effect
timely failure detection, and ensure stable supply of current for
critical components.
Watchdog Timer
The watchdog timer (WDT) monitors system operations based on
user-defined configurations. The WDT can be programmed for different time-out periods, such as from 1 to 255 seconds or from 1 to
255 minutes. The WDT generates a reset signal, then a reset
request, after failure to strobe it within the programmed time
period. A register bit may be enabled to indicate if the watchdog
Introduction
timer caused the reset event. The WDT register is cleared during
the power-on sequence to enable the operating system to take
appropriate action when the watchdog generates a reboot.
Introduction
NuPRO-935A
Bracket
Onboard
Golden
Finger
USB1
VGA
GbE1 (RJ-45)
Y (with LED
indication)
GbE2 (RJ-45)
Y (with LED
indication)
PS/2 KB/MS1*
KB/MS
2.54 pitch
USB2/3
2.54 pitch
Remarks
DB-15
Act/Link/Speed
Act/Link/Speed
USB4/5
2.54 pitch
COM1/2
2.54 pitch
Printer port
IDE
Floppy
SATA-300 1/2
ISA
4 slots
NOTE:
10
Introduction
NuPRO-935A
NuPRO-935A
SATA cable x2
Users manual
NOTE:
WARNING:
Introduction
11
12
Introduction
NuPRO-935A
Hardware Information
This chapter provides information on the NuPRO-935A board layout, connector pin assignments, and jumper settings.
Description
VGA port
1A
NOTE:
Hardware Information
13
Signal
Function
KBDAT
Keyboard Data
MSDAT
Mouse Data
GND
Ground
KBMS5V
Power
KBCLK
Keyboard Clock
MSCLK
Mouse Clock
For boards without a Mini-DIN PS/2 KB/MS connector, customers wishing to use a PS/2 type
keyboard and mouse may purchase a PS/2
cable with bracket (P/N: 30-01019-2000) which
connects to the External Keyboard/Mouse Connector (CN19).
Signal
Function
MSDATA
Mouse Data
NC
not connected
GND
Ground
+5V
Power
CLK
Clock
NC
not connected
14
Pin #
Signal
Function
KBDATA
Keyboard Data
NC
not connected
GND
Ground
+5V
Power
CLK
Clock
NC
not connected
Hardware Information
NuPRO-935A
10BASET/100BASE-TX
1000BASE-T
TX+
BI_DA+
TX-
BI_DA-
RX+
BI_DB+
--
BI_DC+
--
BI_DC-
RX-
BI_DB-
--
BI_DD+
--
BI_DD-
Refer to the table below for the LAN port LED indications.
ACT/LINK LED
SPEED LED
Status
Description
Status
Description
Off
No Link
Off
10 Mb connection
Green
Linked
Amber
100 Mb connection
Blinking
Data Activity
Green
1 Gb connection
USB Connector
Pin # Signal Name
Hardware Information
Vcc
Data-
Data+
GND
15
VGA Port
Pin #
16
Signal
Red
Green
Blue
NC
Ground
Ground
Ground
Ground
+5 V
10
Ground
11
NC
12
DDC DAT
13
HSYNC
14
VSYNC
15
DDC CLK
Hardware Information
NuPRO-935A
3
4
Description
DIMM1
DIMM2
CN1
CN7
FAN1
FAN2
JP5
CN17
CN19
Hardware Information
Clear CMOS
17
10
11
12
13 14
17
18
15
16
20
19
21
22
23
18
Description
10
CN4
11
CN5
COM2 connector
12
CN6
COM1 connector
13
CN2
14
CN3
15
CN8
16
CN10
IDE connector
17
CN11
18
CN12
19
CN13
LPT connector
20
JP1
21
JP2
22
JP3
23
JP4
Hardware Information
NuPRO-935A
NOTE:
Signal
GND
GND
+12V DC
+12V DC
Signal
GND
Fan Tachometer
Hardware Information
Signal
GND
Fan Tachometer
19
20
Pin #
Signal
Pin #
Signal
1
3
5
7
9
11
13
15
17
19
21
23
25
27
29
31
33
35
37
39
Reset IDE
Host data 7
Host data 6
Host data 5
Host data 4
Host data 3
Host data 2
Host data 1
Host data 0
Ground
DRQ0 / DRQ1
Host IOW
Host IOR
IOCHRDY
DACK0 / DACK1
IRQ14 / IRQ 15
Address 1
Address 0
Chip select 0
Activity
2
4
6
8
10
12
14
16
18
20
22
24
26
28
30
32
34
36
38
40
Ground
Host data 8
Host data 9
Host data 10
Host data 11
Host data 12
Host data 13
Host data 14
Host data 15
NC
Ground
Ground
Ground
Host ALE
Ground
No connect
No connect
Address 2
Chip select 1
Ground
Hardware Information
NuPRO-935A
Signal
Pin #
Signal
GND
Extended Density
GND
NC
NC
NC
GND
Index
GND
10
Motor A Select
Hardware Information
11
GND
12
NC
13
GND
14
Drive A Select
15
GND
16
NC
17
GND
18
Step Direction
19
GND
20
Step Pulse
21
GND
22
Write Data
23
GND
24
Write Gate
25
GND
26
Track 0
27
GND
28
Write Protect
29
GND
30
Read Data
31
GND
32
Side 1
33
GND
34
Disk Change
21
Signal
Pin #
Signal
14
Auto-Feed
Parallel Data 0
15
Error
Parallel Data 1
16
Initialize
Parallel Data 2
17
Select
Parallel Data 3
18
Ground
Parallel Data 4
19
Ground
Parallel Data 5
20
Ground
Parallel Data 6
21
Ground
Parallel Data 7
22
Ground
10
Acknowledge
23
Ground
11
Busy
24
Ground
12
Paper Empty
25
Ground
13
Select
26
NC
Signal
GND
AUD_BCLK
GND
ICH_AUD_SDIN0
P5V
ICH_AUD_SDOUT
Function
Ground
Audio Clock
Ground
Audio Data Input
+ 5V
Audio Data Output
P5V_AUD
+ 5V
P3V3_DVDD
3.3V
AUD_SYNC
Audio Synchronous
10
AUD_RST-L
Audio Reset
22
Hardware Information
NuPRO-935A
Signal
Functions
TX-
Transmit (-)
NC
Not Connected
TX+
Transmit (+)
NC
Not Connected
RX+
Receive (+)
NC
Not Connected
RX-
Receive (-)
NC
Not Connected
GND
10
NC
Ground
Not Connected
Hardware Information
Pin #
Signal
Functions
DCD
DSR
RXD
Receive Data
RTS
Request to Send
TXD
Transmit Data
CTS
Clear to Send
DTR
RI
GND
10
NC
23
Signal
Pin #
Signal
+5V
+5V
USB0-
USB1-
USB0+
USB01+
GND
GND
Key
10
NC
Signal
Function
KDAT
Keyboard data
KCLK
Keyboard clock
MDAT
Mouse data
MCLK
Mouse data
P5V_KM
GND
+5 V
Ground
24
Pin #
Signal
1
2
3
4
5
6
7
GND
TXP
TXN
GND
RXN
RXP
GND
Hardware Information
NuPRO-935A
10
11
20
Pin #
Signal
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
P5V
NC
HC_PLEDNC
GND
GND
NC
ATX_PSO
P5V_SB_A
PMEJ
HC_SPKR
NC
NC
P5V
HC_RSTB
GND
HDLED_P
P5V
HC_PBTNJ
GND
Hardware Information
Function
Pin Group
ATX Power
Connector
Chassis Speaker
Power for +5v
RESET signal
Ground
Hard Disk LED signal
Power for +5v
Power-on signal
Ground
Reset Button
Hard Disk LED
Power-on Button
25
2.4 Jumpers
COM1 mode Jumper Settings (JP1-4)
Short the jumper pins according to the following settings to set
COM1 to RS-232/422/485/485+ mode
#
RS-232
RS-422
RS-485
RS-485+
JP1
JP2
JP3
JP4
1-3, 2-4
1-3, 2-4
1-2
-
3-5, 4-6
3-5, 4-6
3-4
1-3, 2-4
3-5, 4-6
3-5, 4-6
5-6
1-3, 2-4
3-5, 4-6
3-5, 4-6
5-6
3-5, 4-6
26
RTC status
Connection
Normal
12
Clear CMOS
23
JP5
Hardware Information
NuPRO-935A
Getting Started
This chapter provides information on how to install components on
the NuPRO-935A SBC.
WARNING:
Getting Started
27
3. Lift the load plate to a 100 angle using your thumb and
forefinger
28
Getting Started
NuPRO-935A
Notch
Golden triangle
Alignment
key
Socket tab
Getting Started
29
7. Close the load plate (A), then fasten the load lever on
the retention tab (B) .
A
30
Getting Started
NuPRO-935A
CAUTION:
The following CPU fan and heatsink assemblies are recommended for use with the NuPRO-935A:
1U LGA 775 CPU Cooler
Dimensions:
Heatsink: 92 x 87.6 x 28 mm
Fan: 75 x 75 x 15 mm
Heatsink: Copper base + copper skived fin
Fan speed: 5500 RPM
Fan airflow: 10.48 CFM
Noise level: 51 dBA
Part number: 32-20065-0000
2U LGA 775 CPU Cooler
Dimensions:
Heatsink: 89 x 83 x 68 mm
Fan: 60 x 60 x 25 mm
Heatsink: Copper base + copper skived fin
Fan speed: 6800 RPM
Fan airflow: 35.3 CFM
Noise level: 46 dBA
Part number: 32-20066-0000
3U LGA 775 CPU Cooler
Dimensions:
Heatsink: 100 x 100 x 70 mm
Fan: 90 x 90 x 25 mm
Heatsink: Aluminum extrusion
Fan speed: 4500 RPM
Fan airflow: 57.7 CFM
Noise level: 47.5 dBA
Part number: 32-20058-0000 + 34-30381-0000
Getting Started
31
CAUTION:
32
Getting Started
NuPRO-935A
CAUTION:
Getting Started
33
34
Getting Started
NuPRO-935A
WARNING:
Channel A: DIMM1
Channel B: DIMM2
Getting Started
35
Notch
Break
4. Insert the module firmly into the slot until the retaining
clips snap back inwards and the module is securely
seated.
36
Getting Started
NuPRO-935A
Driver Installation
This chapter provides information on how to install the
NuPRO-935A device drivers under Windows XP/Vista. The device
drivers are located in the following ADLINK All-in-One DVD
directories:
Chipset Driver
\NuPRO\NuPRO-935A\Chipset\
Display Driver
\NuPRO\NuPRO-935A\VGA\
LAN Driver
\NuPRO\NuPRO-935A\Ethernet\
ISA Driver
\NuPRO\NuPRO-935A\ISA\
TPM Driver
\NuPRO\NuPRO-935A\TPM\
Audio Driver
Driver Installation
37
38
Driver Installation
NuPRO-935A
Driver Installation
39
NOTE:
Before installing the audio driver, check the BIOS settings to make sure that audio is enabled: Chipset >
South Bridge Configurations > HDA Controller (see
Section 5.7.1).
40
Driver Installation
NuPRO-935A
BIOS Setup
The following chapter describes basic navigation for the
AMIBIOS8 BIOS setup utility.
Note:
BIOS Setup
In most cases, the < Delete > key is used to invoke the setup
screen. There are several cases that use other keys, such as < F1
>, < F2 >, and so on.
41
Setup Menu
The main BIOS setup menu is the first screen that you can navigate. Each main BIOS setup menu option is described in this
users guide.
The Main BIOS setup menu screen has two main frames. The left
frame displays all the options that can be configured. Grayed
options cannot be configured, Blue options can be.
The right frame displays the key legend. Above the key legend is
an area reserved for a text message. When an option is selected
in the left frame, it is highlighted in white. Often a text message will
accompany it.
Navigation
The BIOS setup/utility uses a key-based navigation system called
hot keys. Most of the BIOS setup utility hot keys can be used at
any time during the setup navigation process.
These keys include < F1 >, < F10 >, < Enter >, < ESC >, < Arrow >
keys, and so on. .
42
BIOS Setup
NuPRO-935A
Note:
There is a hot key legend located in the right frame on most setup
screens.
The < F8 > key on your keyboard is the Fail-Safe key. It is not displayed on the key legend by default. To set the Fail-Safe settings
of the BIOS, press the < F8 > key on your keyboard. It is located
on the upper row of a standard 101 keyboard. The Fail-Safe settings allow the system to boot up with the least amount of options
set. This can lessen the probability of conflicting settings.
Hotkey Descriptions
F1
The < F1 > key allows you to display the General Help screen.
Press the < F1 > key to open the General Help screen.
BIOS Setup
43
F10
ESC
Enter
44
The < F10 > key allows you to save any changes you have made
and exit Setup. Press the < F10 > key to save your changes. The
following screen will appear:
Press the < Enter > key to save the configuration and exit. You can
also use the < Arrow > key to select Cancel and then press the <
Enter > key to abort this function and return to the previous screen.
The < Esc > key allows you to discard any changes you have made
and exit the Setup. Press the < Esc > key to exit the setup without
saving your changes. The following screen will appear:
Press the < Enter > key to discard changes and exit. You can also
use the < Arrow > key to select Cancel and then press the < Enter
> key to abort this function and return to the previous screen.
The < Enter > key allows you to display or change the setup option
listed for a particular setup item. The < Enter > key can also allow
you to display the setup sub-screens.
BIOS Setup
NuPRO-935A
BIOS Setup
45
46
BIOS Setup
NuPRO-935A
5.3.1
CPU Configuration
You can use this screen to select options for the CPU Configuration Settings. Use the up and down < Arrow > keys to select an
item. Use the < + > and < - > keys to change the value of the
selected option. A description of the selected item appears on the
right side of the screen. The settings are described on the following pages. An example of the CPU Configuration screen is shown
below.
BIOS Setup
47
5.3.2
IDE Configuration
You can use this screen to select options for the IDE Configuration
Settings. Use the up and down < Arrow > keys to select an item.
Use the < + > and < - > keys to change the value of the selected
option. A description of the selected item appears on the right side
of the screen. The settings are described on the following pages.
An example of the IDE Configuration screen is shown below.
SATA Configuration
This item specifies which mode the SATA channels should be
initialized in. The settings are Disabled, Compatible and
Enhanced. When running in Compatible mode, SATA channel
can be configured as a legacy IDE channel.
IDE Master/Slave
Select one of the hard disk drives to configure it. Press
< Enter > to access its sub menu.
48
BIOS Setup
NuPRO-935A
5.3.3
Floppy Configuration
You can use this screen to specify options for the Floppy Configuration Settings. Use the up and down < Arrow > keys to select an
item. Use the < + > and < - > keys to change the value of the
selected option. The settings are described on the following
pages. The screen is shown below.
BIOS Setup
49
5.3.4
Super IO Configuration
You can use this screen to select options for the Super IO settings.
Use the up and down < Arrow > keys to select an item. Use the <
+ > and < - > keys to change the value of the selected option. The
settings are described on the following pages. The screen is
shown below.
50
BIOS Setup
NuPRO-935A
if Serial Port1 uses 3F8/IRQ4, the option, the 3F8/IRQ4 will not
appear in the options of Serial Port2.
Parallel Port Mode
This option specifies the parallel port mode.
X
EPP: The parallel port can be used with devices that adhere
to the Enhanced Parallel Port (EPP) specification. EPP
uses the existing parallel port signals to provide asymmetric
bi-directional data transfer driven by the host device.
ECP: The parallel port can be used with devices that adhere
to the Extended Capabilities Port (ECP) specification. ECP
uses the DMA protocol to achieve data transfer rates up to
2.5 Megabits per second. ECP provides symmetric Bi-directional communication.
IRQ5: Set this value to allow the serial port to use Interrupt
5.
IRQ7: Set this value to allow the serial port to use Interrupt
7. The majority of parallel ports on computer systems use
IRQ7 and I/O Port 378H as the standard setting.
BIOS Setup
51
5.3.5
This option displays the current status of all of the monitored hardware devices / components such as voltages and temperatures.
52
BIOS Setup
NuPRO-935A
5.3.6
Remote Access
Select this option to Enable or Disable the BIOS remote access
feature.
Note:
Enabling Remote Access requires a dedicated serial port connection. Once both serial ports are configured to disabled, you should
set this value to Disabled or it may cause abnormal boot.
BIOS Setup
53
Terminal Type
This option is used to select either VT100/VT-UTF8 or ANSI
terminal type. The settings for this value are ANSI, VT100, or
VT-UTF8.
VT-UTF8 Combo Key Support
This option enables VT-UTF8 Combination Key Support for
ANSI/VT100 terminals. The settings for this value are Enabled
or Disabled.
Sredir Memory Display Delay
This option gives the delay in seconds to display memory information. The options for this value are No Delay, Delay 1 Sec,
Delay 2 Sec, or Delay 4 Sec.
54
BIOS Setup
NuPRO-935A
5.3.7
Trusted Computing
Trusted computing is an industry standard to make personal computers more secure through a dedicated hardware chip, called a
Trusted Platform Module (TPM). This option enables or disables
the TPM support.
BIOS Setup
55
5.3.8
USB Configuration
You can use this screen to select options for the USB Configuration. Use the up and down < Arrow > keys to select an item. Use
the < + > and < - > keys to change the value of the selected
option. The settings are described on the following pages. The
screen is shown below.
56
BIOS Setup
NuPRO-935A
there are no USB drivers loaded on the system. Set this value
to enable or disable the Legacy USB Support.
X
BIOS Setup
57
58
BIOS Setup
NuPRO-935A
5.4.1
IRQ/DMA
BIOS Setup
59
5.4.2
60
BIOS Setup
NuPRO-935A
5.5.1
Use this screen to select options for the Boot Settings Configuration. Use the up and down <Arrow> keys to select an item. Use the
<Plus> and <Minus> keys to change the value of the selected
option. The settings are described on the following pages. The
screen is shown below.
BIOS Setup
61
Quick Boot
Enabling this setting will cause the BIOS power-on self test
routine to skip some of its tests during bootup for faster system
boot.
Quiet Boot
When this feature is enabled, the BIOS will display the fullscreen logo during the boot-up sequence, hiding normal POST
messages.
When it is disabled, the BIOS will display the normal POST
messages, instead of the full-screen logo.
Bootup Num-Lock
This setting is to set the Num Lock status when the system is
powered on. Setting to [On] will turn on the Num Lock key
when the system is powered on. Setting to [Off] will allow users
to use the arrow keys on the numeric keypad.
62
BIOS Setup
NuPRO-935A
5.5.2
The items allow you to set the sequence of boot devices where
BIOS attempts to load the disk operating system. First press
<Enter> to enter the sub-menu. Then you may use the arrow
keys to select the desired device, then press <+>, <-> or
<PageUp>, <PageDown> key to move it up/down in the priority
list.
5.5.3
BIOS Setup
63
Password Support
Two Levels of Password Protection
Provides both a Supervisor and a User password. If you use
both passwords, the Supervisor password must be set first.
The system can be configured so that all users must enter a
password every time the system boots or when Setup is executed, using either or either the Supervisor password or User
password.
The Supervisor and User passwords activate two different levels of password security. If you select password support, you
are prompted for a one to six character password. Type the
password on the keyboard. The password does not appear on
the screen when typed. Make sure you write it down. If you forget it, you must drain NVRAM and re-configure.
64
BIOS Setup
NuPRO-935A
Supervisor Password
Indicates whether a supervisor password has been set.
User Password
Indicates whether a user password has been set.
BIOS Setup
65
66
BIOS Setup
NuPRO-935A
BIOS Setup
67
5.7.1
You can use this screen to select options for the South Bridge
Configuration. Use the up and down <Arrow> keys to select an
item. Use the <Plus> and <Minus> keys to change the value of the
selected option.
68
BIOS Setup
NuPRO-935A
5.7.2
Power Off: Set this value to always power off the system
while AC power is restored.
BIOS Setup
69
70
BIOS Setup
NuPRO-935A
Discard Changes
Select Discard Changes from the Exit menu and press < Enter >.
Select Ok to discard changes.
BIOS Setup
71
72
BIOS Setup
NuPRO-935A
Watchdog Timer
73
//Detect ITE8718F.
Enter_IT8718_Config(ioport);
//Get Chip ID Byte 1 = 0x87, Gip ID Byte
2 = 0x18
outportb(ioport, 0x20);
DevID1 = inportb(ioport+1);
outportb(ioport, 0x21);
DevID2 = inportb(ioport+1);
if((DevID1 == 0x87) && (DevID2 ==
0x18))
chipflag = 1;
if(chipflag == 0)
{
printf("ADLINK Watchdog Timer
Utility of NuPRO-935A\n\n");
printf("Can't find any ITE IT8718F on
system!\n");
Exit_IT8718_Config(ioport);
exit(1);
}
else
{
printf("ADLINK Watchdog Timer
Utility of NuPRO-935A\n\n");
number=atoi(argv[1]);
WDTRUN(ioport,number);
Exit_IT8718_Config(ioport);
}
}
}
void Enter_IT8718_Config(int config_port)
{
switch(config_port)
{
case 0x2E:
//Address port = 0x2E, enter keys
= 0x87, 0x01, 0x55, 0x55
74
Watchdog Timer
NuPRO-935A
outportb(0x2E,
outportb(0x2E,
outportb(0x2E,
outportb(0x2E,
break;
case 0x4E:
//Address port
= 0x87, 0x01, 0x55, 0xAA
outportb(0x2E,
outportb(0x2E,
outportb(0x2E,
outportb(0x2E,
break;
default:
break;
}
0x87);
0x01);
0x55);
0x55);
}
void Exit_IT8718_Config(int config_port)
{
outportb(config_port, 0x02);
outportb(config_port+1, 0x02);
}
void WDTRUN(int config_port,int count_value)
{
int temp;
int counter;
//Select WDT device
outportb(config_port, 0x07);
outportb(config_port+1, 0x07);//device 7
//Set second/minute mode
outportb(config_port, 0x72);
temp = inportb(config_port+1);
if(count_value == 0)
{
counter = count_value;
printf("WDT is Disabled.");
outportb(config_port+1, temp);//WDT
output through PWROK2 default is Disabled.
}// end of (count_value == 0)
Watchdog Timer
75
//
//
//
//
//
//
} // end of WDTRUN
76
Watchdog Timer
NuPRO-935A
Size
Description
(4GB-2MB)
FFE00000
FFFFFFFF
2 MB
(4GB-18MB)
(4GB-17MB-1)
FEE00000
FEEFFFFF
1 MB
(4GB-20MB)
(4GB-19MB-1)
FEC00000
FECFFFFF
1 MB
15MB 16MB
F00000
FFFFFF
1 MB
ISA Hole
960 K 1024 K
F0000 FFFFF
64 KB
896 K 960 K
E0000 EFFFF
64 KB
768 K 896 K
C0000 DFFFF
640 K 768 K
A0000 BFFFF
0 K 640 K
00000 9FFFF
System Resources
77
Data Width
System Resource
8-bits
Parallel port(1)
8-bits
Parallel port(1)
8-bits
Diskette drive(1)
8-bits
Parallel port(1)
16-bits
Open
16-bits
Open
16-bits
Open
78
System Resources
NuPRO-935A
B.3 IO Map
Hex Range
Device
000-01F
02E-02F
040-05F
0C0-0DF
0E0-0EF
Available
0F0
0F1
N/A
0F2-0F3
N/A
0F4
0F5-0F7
0F8
0F9-0FB
0FC
IDE ID port
N/A
IDE Index port
N/A
IDE Data port
0FD-0FF
N/A
100-179
Available
180-181
182-1EF
Available
1F0-1F7
1FB-22F
Available
230 -277
Available
System Resources
79
Hex Range
Device
278-27F
Parallel Port 2
280-2F7
Available
2F8-2FF
Serial Port 2
300-36F
Available
370-377
378-37F
Parallel Port 1
380-3AF
Available
3BC-3BE
3C0-3DF
VGA registers
3E0-3EF
Available
3F0-3F7
3F8-3FF
Serial port 1
4D0
4D1
CF8-CFB
CF9
CFC-CFF
400
480
800
860
0A00~0AFF
200-23Fh
240-25Fh
280-28Fh
2A0-2DFh
300-33Fh
380-39Fh
80
System Resources
NuPRO-935A
Typical Interrupt
Resource
Connected to Pin
Available
Counter 0
N/A
No
Keyboard controller
N/A
No
N/A
No
Note (1)
Note (1)
Note (1)
No
Note (1)
Real-time clock
N/A
No
SCI / PCI
10
PCI / ISA
Note (1)
11
PCI / ISA
Note (1)
12
Note (1)
13
Math Processor
N/A
No
14
Note (1)
15
Secondary IDE
controller / PCI / ISA
Note (1)
81
Connected to Pin
Available
Counter 0
N/A
No
Keyboard controller
N/A
No
N/A
No
Note (1)
Note (1)
Note (1)
No
Note (1)
Real-time clock
N/A
No
SCI / PCI
10
PCI / ISA
Note (1)
11
PCI / ISA
Note (1)
12
Note (1)
IRQ#
82
13
Math Processor
N/A
No
14
Note (1)
15
Secondary IDE
controller / PCI / ISA
Note (1)
16
N/A
Yes
17
N/A
Yes
System Resources
NuPRO-935A
Typical Interrupt
Resource
Connected to Pin
Available
N/A
Yes
19
N/A
Yes
20
N/A
No
21
N/A
UHCI Controller 5
No
22
N/A
ICH9 HDA
No
23
N/A
No
IRQ#
18
System Resources
83
Device #
Function #
Routing
Description
00h
00h
00h
N/A
00
01H
00H
Internal
02
00H
0FFH
N/A
00h
02h
00h
Internal
00h
02h
01h
Internal
00h
19h
00h
Internal
GbE Controller
00h
1Ah
00h
Internal
00h
1Ah
01h
Internal
00h
1Ah
02h
Internal
00h
1Ah
07h
Internal
00h
1Bh
00h
Internal
00h
1Ch
00h
Internal
00h
1Ch
01h
Internal
00h
1Ch
02h
Internal
00h
1Ch
03h
Internal
00h
1Ch
04h
Internal
00h
1Ch
05h
Internal
00h
1Dh
00h
Internal
00h
1Dh
01h
Internal
00h
1Dh
02h
Internal
00h
1Dh
03h
Internal
00h
1Dh
07h
Internal
00h
1Eh
00h
N/A
00h
1Fh
00h
N/A
00h
1Fh
02h
Internal
00h
1Fh
03h
Internal
00h
1Fh
05h
Internal
00h
1Fh
06h
Internal
Thermal Controller
01h
07h
0FFh
external
01h
0Ch
0FFh
external
PCI slot 4
84
System Resources
NuPRO-935A
Bus #
Device #
Function #
Routing
Description
01h
0Dh
0FFh
external
PCI slot 3
01h
0Eh
0FFh
external
PCI slot 2
01h
0Fh
0FFh
external
PCI slot 1
04h
00h
0FFh
Internal
PCIE Port #0
05h
00h
0FFh
Internal
PCIE Port #1
06h
00h
0FFh
Internal
PCIE Port #2
07h
00h
0FFh
Internal
PCIE Port #3
08h
00h
0FFh
Internal
PCIE Port #4
09h
00h
0FFh
Internal
PCIE Port #5
System Resources
85
INT Line
INTA
INTB
INTC
INTD
INTA
INTB
INTC
INTD
VGA
X
X
SATA Controller
SATA Controller1
SMBUS Controller
Thermal Controller
UHCI 1
UHCI 2
UHCI 3
UHCI 4
X
X
UHCI 5
UHCI 6
X
X
UHCI 7
EHCI 1
EHCI 2
HDA
Intel GBE
PCIE port 0
INTA
INTB
INTC
INTD
PCIE port 1
INTB
INTC
INTD
INTA
PCIE port 2
INTC
INTD
INTA
INTB
PCIE port 3
INTD
INTA
INTB
INTC
PCIE port 4
INTA
INTB
INTC
INTD
PCIE port 5
INTB
INTC
INTD
INTA
PCI Slot1
INTB
INTC
INTD
INTA
PCI Slot2
INTC
INTD
INTA
INTB
PCI Slot3
INTD
INTA
INTB
INTC
PCI Slot4
INTA
INTB
INTC
INTD
86
System Resources
NuPRO-935A
Secure the power cord (do not place any object on/over
the power cord);
87
WARNING:
88
NuPRO-935A
Getting Service
Contact us should you require any service or assistance.
ADLINK Technology, Inc.
Address: 9F, No.166 Jian Yi Road, Zhonghe District
New Taipei City 235, Taiwan
166 9
Tel:
+886-2-8226-5877
Fax:
+886-2-8226-5717
Email:
service@adlinktech.com
Ampro ADLINK Technology, Inc.
Address: 5215 Hellyer Avenue, #110, San Jose, CA 95138, USA
Tel:
+1-408-360-0200
Toll Free: +1-800-966-5200 (USA only)
Fax:
+1-408-360-0222
Email:
info@adlinktech.com
ADLINK Technology (China) Co., Ltd.
Address: 300 (201203)
300 Fang Chun Rd., Zhangjiang Hi-Tech Park,
Pudong New Area, Shanghai, 201203 China
Tel:
+86-21-5132-8988
Fax:
+86-21-5132-3588
Email:
market@adlinktech.com
ADLINK Technology Beijing
Address: 1 E 801 (100085)
Rm. 801, Power Creative E, No. 1, B/D
Shang Di East Rd., Beijing, 100085 China
Tel:
+86-10-5885-8666
Fax:
+86-10-5885-8625
Email:
market@adlinktech.com
ADLINK Technology Shenzhen
Address:
A1 2 C (518057)
2F, C Block, Bldg. A1, Cyber-Tech Zone, Gao Xin Ave. Sec. 7,
High-Tech Industrial Park S., Shenzhen, 518054 China
Tel:
+86-755-2643-4858
Fax:
+86-755-2664-6353
Email:
market@adlinktech.com
Getting Service
89
90
Getting Service