Академический Документы
Профессиональный Документы
Культура Документы
..
.
..
.
..
ADVANCE DATA
SIP9
(Plastic Package)
DESCRIPTION
The TDA8133 is a monolithic dual positive voltage
regulator designed to provide fixed precision output
voltages of 5.1V and 8V at currents up to 0.75A.
An internal reset circuit generates a reset pulse
when the output 1 decrease below the regulated
voltage value.
Output 2 can be disabled by TTL input.
Short circuit and thermal protections are included
in all the versions.
9
8
OUTPUT 1
OUTPUT 2
7
6
N.C.
RESET
GROUND
DISABLE
3
2
DEL. CAP.
INPUT 2
INPUT 1
8133-01.EPS
PIN CONNECTIONS
March 1994
This is advance information on a new product now in development or undergoing evaluation. Details are subject to change without notice.
1/5
TDA8133
BLOCK DIAGRAM
IN 1
IN 2
OUT 1
REFERENCE
PROTECTION
OUT 1
RESET
RESET
3
DELAY
CAPACITOR
DISABLE
OUT 2
OUT 2
TDA8133
8133-02.EPS
DISABLE 4
Symbol
Value
Unit
VIN
Parameter
20
VDIS
20
VRST
20
IO1, 2
Output Currents
Internally Limited
Power Dissipation
Internally Limited
Pt
Tstg
Tj
Storage Temperature
Junction Temperature
-65 to +150
0 to +150
C
C
8133-01.TBL
THERMAL DATA
2/5
Parameter
Value
Unit
Rth (j-c)
Rth (j-a)
60
Tj
130
C/W
C/W
o
8133-02.TBL
Symbol
TDA8133
ELECTRICAL CHRACTERISTICS (VIN1 = 7V, VIN2 = 10V, Tj = 25oC, unless otherwise specified)
Min.
Typ.
Max.
Unit
VO1
Output Voltage
IO1 = 10mA
5.1
5.2
VO2
Output Voltage
IO2 = 10mA
7.84
8.16
VO1
Output Voltage
4.9
5.3
VO2
Output Voltage
7.7
8.3
VIO1,2
Dropout Voltage
IO1,2 = 750mA
1.4
VO1,2LI
Line Regulation
50
80
mV
mV
VO1,2LO
Load Regulation
100
160
mV
mV
Quiescent Current
IO1 = 10mA
Output 2 Disabled
mA
K = VO1
K0.25
K - 0.1
50
75
mV
IQ
VO1RST
Parameter
Test Conditions
K - 0.4
tRD
Ce = 100nF
See circuit description
VRL
I5 = 5mA
0.4
IRH
V5 = 10V
10
KO1,2
Tj = 0 to 125 C
VO 106
KO =
T VO
IO1,2SC
VDISH
VDISL
VRTH
IDIS
Tjsd
20
25
ms
100
ppm/ C
1.6
1
2
A
A
V
-100
145
0.8
8133-03.TBL
Symbol
Note : Safe permanent short-circuit is only guaranteed for input voltages up to 16V.
CIRCUIT DESCRIPTION
The TDA8133 is a dual voltage regulator with Reset
and Disable.
The two regulation parts are supplied from one
voltage reference circuit trimmed by zener zap
during EWS test.
Since the supply voltage of this last is connected at
Pin 1 (VIN1), the regulator 2 will not work if Pin 1 is
not supplied.
The outputs stage have been realized in darlington
configuration with a drop typical 1.2V.
The disable circuit, switch-off the output 2 if a
voltage lower than 0.8V is applied at Pin 4.
The Reset circuit checks the voltage at the output 1. If this one goes below VOUT - 0.25V (4.85V
typ.), the comparator "a" (see Figure 1) discharges
rapidly the capacitor Ce and the reset output goes
at once Low. When the voltage at the out1 rises
above VOUT - 0.2V (4.9V typ.), the voltage VCe
increases linearly to 2.5V corresponding to a delay
Ce 2.5V
(see Figure 2),
td following the law : t1 =
10A
then the reset output goes high again. To avoid
gliches in the reset output, the second comparator
"b" has a large hysteresis (1.9V).
3/5
TDA8133
Figure 1
10A
REF
2.5V
+
-
OUT 1 9
50
RESET
6
REG
Ce
8133-03.EPS
2.5V 0.6V
Figure 2
5.1V
Vout LOW
4.9V
4.85V
TD
TD
8133-04.EPS
RESET
TYPICAL APPLICATION
RESET
0.1F
Ce
6
V IN1
V O1
V O2
TDA8133
C1
C2
C3
DISABLE
C1 to C4 = 10 F
4/5
C4
8133-05.EPS
V IN2
TDA8133
PACKAGE MECHANICAL DATA
9 PINS - PLASTIC SIP
C
L3
L1
c2
d1
a1
L2
PM-SIP9.EPS
b1
b3
e3
c1
A
a1
B
b1
b3
C
c1
c2
D
d1
e
e3
L
L1
L2
L3
M
N
Min.
Millimeters
Typ.
2.7
Max.
7.1
3
24.8
Min.
0.106
0.5
0.85
Inches
Typ.
Max.
0.280
0.118
0.976
0.020
1.6
0.033
3.3
0.43
1.32
0.063
0.130
0.017
0.052
21.2
0.835
14.5
2.54
20.32
0.571
0.100
0.800
3.1
0.122
3
17.6
0.118
0.693
0.25
3.2
1
0.010
SIP9.TBL
Dimensions
0.126
0.039
Information furnished is believed to be accurate and reliable. However, SGS-THOMSON Microelectronics assumes no responsibility
for the consequences of use of such information nor for any infringement of patents or other rights of third parties which may result
from its use. No licence is granted by implication or otherwise under any patent or patent rights of SGS-THOMSON Microelectronics.
Specifications mentioned in this publication are subject to change without notice. This publication supersedes and replaces all
information previously supplied. SGS-THOMSON Microelectronics products are not authorized for use as critical components in life
support devices or systems without express written approval of SGS-THOMSON Microelectronics.
1994 SGS-THOMSON Microelectronics - All Rights Reserved
Purchase of I2C Components of SGS-THOMSON Microelectronics, conveys a license under the Philips
I2C Patent. Rights to use these components in a I2C system, is granted provided that the system conforms to
the I2C Standard Specifications as defined by Philips.
SGS-THOMSON Microelectronics GROUP OF COMPANIES
Australia - Brazil - China - France - Germany - Hong Kong - Italy - Japan - Korea - Malaysia - Malta - Morocco
The Netherlands - Singapore - Spain - Sweden - Switzerland - Taiwan - Thailand - United Kingdom - U.S.A.
5/5