Академический Документы
Профессиональный Документы
Культура Документы
Categories:
Material
Notes:
This alloy has good workability, very good corrosion resistance, high fatigue strength, weldability, and moderate strength. This leads to its use in aircraft
fuel/oil lines, fuel tanks, other transportation areas, sheet metal work, appliances and lighting, wire, and rivets.
Data points with the AA note have been provided by the Aluminum Association, Inc. and are NOT FOR DESIGN.
Composition Notes:
Composition information provided by the Aluminum Association and is not for design.
Key Words:
Vendors:
No vendors are listed for this material. Please click here if you are a supplier and would like information on how to add your listing to this material.
Physical Properties
Density
Mechanical Properties
Hardness,Brinell
TensileStrength,Ultimate
TensileStrength,Yield
Elongation at Break
Metric
2.68 g/cc
English
0.0968 lb/in
Comments
AA; Typical
Metric
47
193 MPa
34.0 MPa
English
47
28000 psi
4930 psi
Comments
AA; Typical; 500 g load; 10 mm ball
AA; Typical
@Temperature371C
@Temperature700F
52.0 MPa
7540 psi
@Temperature316C
@Temperature601F
83.0 MPa
12000 psi
@Temperature260C
@Temperature500F
117 MPa
17000 psi
@Temperature204C
@Temperature399F
159 MPa
23100 psi
@Temperature149C
@Temperature300F
193 MPa
28000 psi
@Temperature -28.0C
@Temperature -18.4F
193 MPa
28000 psi
@Temperature24.0C
@Temperature75.2F
193 MPa
28000 psi
@Temperature100C
@Temperature212F
200 MPa
29000 psi
@Temperature -80.0C
@Temperature -112F
303 MPa
43900 psi
@Temperature -196C
@Temperature -321F
89.6 MPa
21.0 MPa
13000 psi
3050 psi
@Strain 0.200 %,
Temperature371C
@Strain 0.200 %,
Temperature700F
38.0 MPa
5510 psi
@Strain 0.200 %,
Temperature316C
@Strain 0.200 %,
Temperature601F
52.0 MPa
7540 psi
@Strain 0.200 %,
Temperature260C
@Strain 0.200 %,
Temperature500F
76.0 MPa
11000 psi
@Strain 0.200 %,
Temperature204C
@Strain 0.200 %,
Temperature399F
90.0 MPa
13100 psi
@Strain 0.200 %,
Temperature -80.0C
@Strain 0.200 %,
Temperature -112F
90.0 MPa
13100 psi
@Strain 0.200 %,
Temperature -28.0C
@Strain 0.200 %,
Temperature -18.4F
90.0 MPa
13100 psi
@Strain 0.200 %,
Temperature24.0C
@Strain 0.200 %,
Temperature75.2F
90.0 MPa
13100 psi
@Strain 0.200 %,
Temperature100C
@Strain 0.200 %,
Temperature212F
90.0 MPa
13100 psi
@Strain 0.200 %,
Temperature149C
@Strain 0.200 %,
Temperature300F
110 MPa
16000 psi
@Strain 0.200 %,
Temperature -196C
@Strain 0.200 %,
Temperature -321F
30.0 %
30.0 %
AA; Typical
Page 1 / 3
@Temperature24.0C
@Temperature75.2F
32.0 %
32.0 %
@Temperature -28.0C
@Temperature -18.4F
35.0 %
35.0 %
@Temperature -80.0C
@Temperature -112F
36.0 %
36.0 %
@Temperature100C
@Temperature212F
46.0 %
46.0 %
@Temperature -196C
@Temperature -321F
50.0 %
50.0 %
@Temperature149C
@Temperature300F
60.0 %
60.0 %
@Temperature204C
@Temperature399F
80.0 %
80.0 %
@Temperature260C
@Temperature500F
110 %
110 %
@Temperature316C
@Temperature601F
130 %
130 %
@Temperature371C
@Temperature700F
25.0 %
25.0 %
@Thickness 1.59 mm
@Thickness 0.0625 in
AA; Typical
30.0 %
30.0 %
@Diameter 12.7 mm
@Diameter 0.500 in
ModulusofElasticity
70.3 GPa
10200 ksi
UltimateBearingStrength
BearingYieldStrength
PoissonsRatio
FatigueStrength
345 MPa
131 MPa
0.330
110 MPa
50000 psi
19000 psi
0.330
16000 psi
@# of Cycles 5.00e+8
@# of Cycles 5.00e+8
30 %
25.9 GPa
124 MPa
30 %
3760 ksi
18000 psi
Metric
0.00000499 ohm-cm
English
0.00000499 ohm-cm
Comments
AA; Typical
@Temperature20.0C
@Temperature68.0F
Metric
22.1 m/m-C
English
12.3 in/in-F
Machinability
ShearModulus
ShearStrength
Electrical Properties
ElectricalResistivity
Thermal Properties
CTE, linear
SpecificHeatCapacity
ThermalConductivity
MeltingPoint
Solidus
Liquidus
Processing Properties
AnnealingTemperature
Hot-WorkingTemperature
23.8 m/m-C
13.2 in/in-F
23.8 m/m-C
13.2 in/in-F
24.8 m/m-C
13.8 in/in-F
25.7 m/m-C
14.3 in/in-F
25.7 m/m-C
14.3 in/in-F
0.880 J/g-C
138 W/m-K
607.2 - 649C
607.2C
649C
AA; Typical
AA; Typical; Average of tension and compression. Compression
modulus is about 2% greater than tensile modulus.
Edge distance/pin diameter = 2.0
Edge distance/pin diameter = 2.0
completely reversed stress; RR Moore machine/specimen
AA; Typical
Comments
average
0.210 BTU/lb-F
Estimated from trends in similar Al alloys.
960 BTU-in/hr-ft-F
AATypicalat77F
1125 - 1200F AA; Typical range based on typical composition for wrought products
1/4 inch thickness or greater
1125F
AA; Typical
1200F
AA; Typical
Metric
343C
260 - 510C
English
650F
500 - 950F
Comments
holding at temperature not required
Metric
95.7 - 97.7 %
0.15 - 0.35 %
<= 0.10 %
<= 0.40 %
2.20 - 2.80 %
<= 0.10 %
<= 0.050 %
<= 0.15 %
English
95.7 - 97.7 %
0.15 - 0.35 %
<= 0.10 %
<= 0.40 %
2.20 - 2.80 %
<= 0.10 %
<= 0.050 %
<= 0.15 %
Comments
As remainder
Page 2 / 3
Silicon,Si
Zinc,Zn
<= 0.25 %
<= 0.10 %
<= 0.25 %
<= 0.10 %
Page 3 / 3