Академический Документы
Профессиональный Документы
Культура Документы
Package:
28-contact QFN
Description
The A4988 is a complete microstepping motor driver with
built-in translator for easy operation. It is designed to operate
bipolar stepper motors in full-, half-, quarter-, eighth-, and
sixteenth-step modes, with an output drive capacity of up to
35 V and 2 A. The A4988 includes a fixed off-time current
regulator which has the ability to operate in slow or mixed
decay modes.
The translator is the key to the easy implementation of the
A4988. Simply inputting one pulse on the STEP input drives
the motor one microstep. There are no phase sequence tables,
high-frequency control lines, or complex interfaces to program.
The A4988 interface is an ideal fit for applications where a
complex microprocessor is unavailable or is overburdened.
During stepping operation, the chopping control in the A4988
automatically selects the current decay mode: slow or mixed. In
mixed decay mode, the device is set initially to a fast decay for
a proportion of the fixed off-time, then to a slow decay for the
remainder of the off-time. Mixed decay current control results
in reduced audible motor noise, increased step accuracy, and
reduced power dissipation.
Not to scale
Continued on the next page
0.1 F
VREG ROSC
0.22 F
0.1 F
0.22 F
CP1
CP2
VCP
VDD
VBB2
5 k
Microcontroller or
Controller Logic
SLEEP
STEP
VBB1
OUT1A
A4988
OUT1B
SENSE1
MS1
MS2
MS3
OUT2A
DIR
OUT2B
ENABLE
SENSE2
RESET
VREF
4988-DS, Rev. 6
GND
GND
100 F
A4988
Description (continued)
Internal synchronous rectification control circuitry is provided
to improve power dissipation during PWM operation. Internal
circuit protection includes: thermal shutdown with hysteresis,
undervoltage lockout (UVLO), and crossover-current protection.
Special power-on sequencing is not required.
Selection Guide
Part Number
A4988SETTR-T
Package
Packing
Symbol
VBB
Notes
Rating
Units
35
Output Current
IOUT
VIN
0.3 to 5.5
VDD
0.3 to 5.5
2.0 to 37
VSENSE
0.5 to 0.5
VREF
5.5
20 to 85
TJ(max)
150
Tstg
55 to 150
TA
Range S
A4988
0.1 F
0.22 F
VREG
VDD
Current
Regulator
ROSC
CP1
CP2
Charge
Pump
OSC
VCP
0.1 F
DMOS Full Bridge
REF
DAC
VBB1
OUT1A
OUT1B
PWM Latch
Blanking
Mixed Decay
STEP
OCP
Gate
Drive
DIR
RESET
MS1
Translator
Control
Logic
MS2
PWM Latch
Blanking
Mixed Decay
ENABLE
SLEEP
DAC
VBB2
RS1
OUT2A
OCP
MS3
SENSE1
OUT2B
SENSE2
RS2
VREF
A4988
Symbol
VBB
VDD
Output On-Resistance
Rds(on)
VF
IBB
IDD
Test Conditions
Operating
During Sleep Mode
Operating
Source driver, IOUT = 1.5 A
Sink driver, IOUT = 1.5 A
Source diode, IF = 1.5 A
Sink diode, IF = 1.5 A
fPWM < 50 kHz
Operating, outputs disabled
Sleep Mode
fPWM < 50 kHz
Outputs off
Sleep Mode
Min.
Typ.2
Max.
Units
8
0
3
320
320
35
35
5.5
430
430
1.2
1.2
4
2
10
8
5
10
V
V
V
m
m
V
V
mA
mA
A
mA
mA
A
VDD 0.7
20
20
5
0.7
20
23
0
3
100
<1.0
<1.0
100
50
100
11
1
30
30
475
VDD 0.3
20
20
19
1.3
40
37
4
3
15
5
5
800
V
V
A
A
k
k
k
%
s
s
s
V
A
%
%
%
ns
2.1
2.7
165
15
2.8
90
2.9
A
C
C
V
mV
Control Logic
Logic Input Voltage
Logic Input Current
Microstep Select
Logic Input Hysteresis
Blank Time
VIN(1)
VIN(0)
IIN(1)
IIN(0)
RMS1
RMS2
RMS3
VHYS(IN)
tBLANK
Fixed Off-Time
tOFF
VREF
IREF
errI
tDT
IOCPST
TTSD
TTSDHYS
VDDUVLO
VDDUVLOHYS
VDD rising
1 For
input and output current specifications, negative current is defined as coming out of (sourcing) the specified device pin.
data are for initial design estimations only, and assume optimum manufacturing and application conditions. Performance may vary for individual
units, within the specified maximum and minimum limits.
3V
ERR = [(VREF/8) VSENSE] / (VREF/8).
4 Overcurrent protection (OCP) is tested at T = 25C in a restricted range and guaranteed by characterization.
A
2 Typical
A4988
THERMAL CHARACTERISTICS
Characteristic
Symbol
RJA
Test Conditions*
Value Units
32
C/W
4.00
3.50
3.00
2.50
2.00
32
/W
1.50
1.00
0.50
0
20
40
60
80
100
120
Temperature, TA (C)
140
160
A4988
tA
tB
STEP
tC
tD
Time Duration
Symbol
Typ.
Unit
tA
tB
tC
200
ns
tD
200
ns
MS2
MS3
Microstep Resolution
Excitation Mode
Full Step
2 Phase
Half Step
1-2 Phase
Quarter Step
W1-2 Phase
Eighth Step
2W1-2 Phase
Sixteenth Step
4W1-2 Phase
A4988
A4988
Slow
Decay
Mixed
Decay
Slow
Decay
Mixed
Decay
Slow
Decay
Mixed
Decay
Slow
Decay
Mixed
Decay
Missed
Step
t , 1 s/div.
Figure 2: Missed Steps in Low-Speed Microstepping
Mixed Decay
No Missed
Steps
t , 1 s/div.
Figure 3: Continuous Stepping Using Automatically-Selected Mixed Stepping (ROSC pin grounded)
A4988
Direction Input (DIR). This determines the direction of rotation of the motor. Changes to this input do not take effect until the
next STEP rising edge.
Internal PWM Current Control. Each full-bridge is con-
RS)
ITripMAX
A4988
5 A / div.
Fault
latched
FET outputs. When set to a logic high, the outputs are disabled.
When set to a logic low, the internal control enables the outputs
as required. The translator inputs STEP, DIR, and MSx, as well as
the internal sequencing logic, all remain active, independent of the
E N A B
L
E input state.
t
Figure 4: Short-to-Ground Event
5 A / div.
Fixed off-time
when the motor is not in use, this input disables much of the
internal circuitry including the output FETs, current regulator,
and charge pump. A logic low on the S L
E E P pin puts the A4988
into Sleep mode. A logic high allows normal operation, as well
as startup (at which time the A4988 drives the motor to the Home
microstep position). When emerging from Sleep mode, in order
to allow the charge pump to stabilize, provide a delay of 1 ms
before issuing a Step command.
t
Figure 5. Shorted Load (OUTxA OUTxB) in Slow Decay Mode
5 A / div.
Fixed off-time
triggered by an internal fixed-off time cycle, load current recirculates according to the decay mode selected by the control logic.
This synchronous rectification feature turns on the appropriate
FETs during current decay, and effectively shorts out the body
diodes with the low FET Rds(on). This reduces power dissipation
significantly, and can eliminate the need for external Schottky
diodes in many applications. Synchronous rectification turns off
when the load current approaches zero (0 A), preventing reversal
of the load current.
10
A4988
VSTEP
100.00
70.71
See Enlargement A
IOUT
70.71
100.00
Enlargement A
toff
IPEAK
tFD
tSD
Slow Decay
Mixed Decay
IOUT
Fa
st
De
ca
t
Symbol
toff
IPEAK
Characteristic
Device fixed off-time
Maximum output current
tSD
tFD
IOUT
11
A4988
Layout. The printed circuit board should use a heavy groundplane. For optimum electrical and thermal performance, the
A4988 must be soldered directly onto the board. Pins 3 and 18
are internally fused, which provides a path for enhanced thermal
dissipation. Theses pins should be soldered directly to an exposed
surface on the PCB that connects to thermal vias are used to
transfer heat to other layers of the PCB.
In order to minimize the effects of ground bounce and offset
issues, it is important to have a low-impedance single-point
ground, known as a star ground, located very close to the device.
By making the connection between the pad and the ground plane
directly under the A4988, that area becomes an ideal location for
a star ground point. A low-impedance ground will prevent ground
bounce during high-current operation and ensure that the supply
voltage remains stable at the input terminal.
Solder
A4988
Trace (2 oz.)
Signal (1 oz.)
Ground (1 oz.)
PCB
Thermal (2 oz.)
Thermal Vias
RS1
RS2
ENABLE
VBB1
SENSE1
NC
OUT1A
NC
PAD
DIR
VDD
C6
SLEEP
STEP
NC
ROSC
VCP
RESET
GND
REF
MS3
CP2
VREG
C4
A4988
GND
CP1
MS1
C3
VBB
C2
OUT1B
OUT2B
MS2
OUT2A
VBB2
C9
SENSE2
C7
R3
R2
VDD
C1
C8
R6
R1
12
A4988
VDD
VBB
VBB
8V
GND
GND
SENSE
GND
CP2
GND
GND
GND
GND
GND
VBB
10 V
CP1
40 V
PGND
VREG
VCP
VREG
DMOS
Parasitic
GND
8V
MS1
MS2
MS3
DIR
VREF
ROSC
SLEEP
VBB
OUT
DMOS
Parasitic
8V
GND
GND
DMOS
Parasitic
GND
13
A4988
RESET
STEP
STEP
100.00
Slow
70.71
70.71
100.00
100.00
0.00
Phase 2
IOUT2A
Direction = H
(%)
100.00
100.00
70.71
Phase 2
IOUT2B
Direction = H
(%)
0.00
70.71
Slow
Mixed
Mixed
0.00
70.71
70.71
Slow
Mixed
Home Microstep Position
Phase 1
IOUT1A
Direction = H
(%)
Slow
Phase 1
IOUT1A
Direction = H
(%)
Mixed*
70.71
Mixed*
Mixed*
Slow Slow
Mixed
100.00
Slow
Mixed
Slow
Mixed
0.00
70.71
100.00
100.00
DIR= H
DIR= H
STEP
100.00
92.39
70.71
Slow
Mixed
Slow
38.27
70.71
92.39
100.00
100.00
92.39
Slow
Mixed*
70.71
Phase 2
IOUT2B
Direction = H
(%)
Mixed
0.00
Home Microstep Position
Phase 1
IOUT1A
Direction = H
(%)
Mixed*
38.27
38.27
Slow
Mixed
Slow
Mixed
Slow
Mixed
0.00
38.27
70.71
92.39
100.00
DIR= H
Figure 11: Decay Modes for Quarter-Step Increments
14
A4988
STEP
100.00
92.39
83.15
70.71
55.56
Mixed*
38.27
19.51
0.00
Slow
19.51
38.27
55.56
70.71
83.15
92.39
100.00
100.00
92.39
83.15
70.71
55.56
Phase 2
IOUT2B
Direction = H
(%)
Mixed
0.00
Mixed
Mixed
Slow
Mixed*
38.27
19.51
Slow
Phase 1
IOUT1A
Direction = H
(%)
Mixed
Slow
19.51
38.27
55.56
70.71
83.15
92.39
100.00
DIR= H
15
A4988
STEP
100.00
95.69
88.19
83.15
77.30
70.71
63.44
55.56
47.14
Mixed*
38.27
29.03
19.51
Phase 1
IOUT1A
Direction = H
(%)
9.8
Slow
0.00
Mixed
Slow
Mixed
9.8
19.51
29.03
38.27
47.14
55.56
63.44
70.71
77.30
83.15
88.19
95.69
100.00
100.00
95.69
88.19
83.15
77.30
70.71
63.44
55.56
47.14
Mixed*
38.27
29.03
19.51
Phase 2
IOUT2B
Direction = H
(%)
9.8
0.00
Slow
Mixed
Slow
Mixed
Slow
9.8
19.51
29.03
38.27
47.14
55.56
63.44
70.71
77.30
83.15
88.19
95.69
100.00
DIR= H
Figure 13: Decay Modes for Sixteenth-Step Increments
16
A4988
Half
Step
#
1
1/4
Step
#
1
1/8
Step
#
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
1/16
Step
#
1
Phase 1
Current
[% ItripMax]
(%)
100.00
Phase 2
Current
[% ItripMax]
(%)
0.00
Step
Angle
()
0.0
99.52
9.80
5.6
98.08
19.51
11.3
95.69
29.03
16.9
92.39
38.27
22.5
88.19
47.14
28.1
83.15
55.56
33.8
77.30
63.44
39.4
70.71
70.71
45.0
10
63.44
77.30
50.6
11
55.56
83.15
56.3
12
47.14
88.19
61.9
13
38.27
92.39
67.5
14
29.03
95.69
73.1
15
19.51
98.08
78.8
16
9.80
99.52
84.4
17
0.00
100.00
90.0
18
9.80
99.52
95.6
19
19.51
98.08
101.3
20
29.03
95.69
106.9
21
38.27
92.39
112.5
22
47.14
88.19
118.1
23
55.56
83.15
123.8
24
63.44
77.30
129.4
25
70.71
70.71
135.0
26
77.30
63.44
140.6
27
83.15
55.56
146.3
28
88.19
47.14
151.9
29
92.39
38.27
157.5
30
95.69
29.03
163.1
31
98.08
19.51
168.8
32
99.52
9.80
174.4
Full
Step
#
Half
Step
#
5
1/4
Step
#
9
1/8
Step
#
17
18
10
19
20
11
21
22
12
23
24
13
25
26
14
27
28
15
29
30
16
31
32
Phase 1
Current
Phase 2
Current
1/16
Step
#
33
[% ItripMax]
34
99.52
9.80
185.6
35
98.08
19.51
191.3
36
95.69
29.03
196.9
37
92.39
38.27
202.5
38
88.19
47.14
208.1
39
83.15
55.56
213.8
40
77.30
63.44
219.4
41
70.71
70.71
225.0
42
63.44
77.30
230.6
43
55.56
83.15
236.3
44
47.14
88.19
241.9
45
38.27
92.39
247.5
46
29.03
95.69
253.1
47
19.51
98.08
258.8
48
9.80
99.52
264.4
49
0.00
100.00
270.0
50
9.80
99.52
275.6
51
19.51
98.08
281.3
52
29.03
95.69
286.9
53
38.27
92.39
292.5
54
47.14
88.19
298.1
55
55.56
83.15
303.8
56
63.44
77.30
309.4
57
70.71
70.71
315.0
58
77.30
63.44
320.6
59
83.15
55.56
326.3
60
88.19
47.14
331.9
61
92.39
38.27
337.5
62
95.69
29.03
343.1
63
98.08
19.51
348.8
64
99.52
9.80
354.4
(%)
100.00
[% ItripMax]
(%)
0.00
Step
Angle
()
180.0
17
A4988
22 VBB1
23 SENSE1
24 OUT1A
25 NC
26 OUT2A
27 SENSE2
28 VBB2
Pinout Diagram
OUT2B
21 OUT1B
ENABLE
20 NC
GND
CP1
CP2
17 REF
VCP
16 STEP
NC
15 VDD
SLEEP 14
ROSC 13
18 GND
RESET 12
MS3 11
9
MS1
MS2 10
8
VREG
19 DIR
PAD
Name
Number
Description
CP1
CP2
VCP
VREG
MS1
Logic input
MS2
10
Logic input
MS3
11
Logic input
RESET
12
Logic input
ROSC
13
Timing set
SLEEP
14
Logic input
VDD
15
Logic supply
STEP
16
Logic input
REF
17
GND
3, 18
Ground*
DIR
19
Logic input
OUT1B
21
VBB1
22
Load supply
SENSE1
23
OUT1A
24
OUT2A
26
SENSE2
27
VBB2
28
Load supply
OUT2B
ENABLE
Logic input
NC
7, 20, 25
PAD
No connection
Exposed pad for enhanced thermal dissipation*
*The GND pins must be tied together externally by connecting to the PAD ground plane
under the device.
18
A4988
1.15
28
1
2
0.50
28
A
5.00 0.15
3.15
4.80
3.15
29X
SEATING
PLANE
0.08 C
+0.05
0.25 0.07
0.90 0.10
4.80
C
0.50
0.73 MAX
B
2
1
28
3.15
3.15
19
A4988
Revision History
Revision
Revision Date
May 7, 2014
Description of Revision
Updated IOCPST
Revised text on page 9; revised Figure 8 and Table 2
Updated VBB, IBB, and IDD in Electrical Characteristics table
20