Академический Документы
Профессиональный Документы
Культура Документы
www.hilti.co.uk
Company:
Specifier:
Address:
Phone I Fax:
E-Mail:
Page:
Project:
Sub-Project I Pos. No.:
Date:
1
Damac Twin Towers
5/4/2014
Specifier's comments:
1. Input data
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor ( c ) 2003-2009 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.co.uk
Company:
Specifier:
Address:
Phone I Fax:
E-Mail:
Page:
Project:
Sub-Project I Pos. No.:
Date:
2
Damac Twin Towers
5/4/2014
Tension force
Shear force
Shear force x
Shear force y
7.999
7.800
7.800
0.000
7.999
7.800
7.800
0.000
Tension
Compression
x
Load [kN]
Capacity [kN]
Utilization bN [%]
Status
7.999
62.643
13
OK
N/A
N/A
N/A
N/A
15.997
44.871
36
OK
N/A
N/A
N/A
N/A
Steel Strength
NRk,s [kN]
g M,s
NRd,s [kN]
NSd [kN]
87.700
1.400
62.643
7.999
Ac,N [mm ]
Ac,N [mm ]
y A,N
c cr,N [mm]
s cr,N [mm]
70200
38025
1.846
98
195
e c1,N [mm]
y ec1,N
e c2,N [mm]
y ec2,N
y s,N
y re,N
k1
1.000
1.000
1.000
1.000
11.000
NRk,c [kN]
g M,c
NRd,c [kN]
NSd [kN]
36.458
1.500
44.871
15.997
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor ( c ) 2003-2009 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.co.uk
Company:
Specifier:
Address:
Phone I Fax:
E-Mail:
Page:
Project:
Sub-Project I Pos. No.:
Date:
3
Damac Twin Towers
5/4/2014
Utilization bV [%]
Load [kN]
Capacity [kN]
7.800
45.200
17
OK
N/A
N/A
N/A
N/A
Pryout Strength**
15.600
130.127
12
OK
15.600
39.819
39
OK
Status
x+**
* anchor having the highest loading
g M,s
V Rd,s [kN]
VSd [kN]
56.500
1.250
45.200
7.800
Pryout Strength
0
Ac,N [mm ]
Ac,N [mm ]
y A,N
c cr,N [mm]
s cr,N [mm]
k4
70200
38025
1.846
98
195
2.900
e c1,V [mm]
y ec1,N
e c2,V [mm]
y ec2,N
y s,N
y re,N
1.000
1.000
1.000
1.000
NRk,c [kN]
g M,c,p
VRd,c1 [kN]
VSd [kN]
36.458
1.500
130.127
15.600
d nom [mm]
kv
65
16
2.400
0.066
0.064
c 1 [mm]
Ac,V [mm ]
A c,V [mm ]
y A,V
150
138375
101250
1.367
y s,V
y h,V
y a,V
e c,V [mm]
y ec,V
y re,V
y 90,V
1.000
1.000
1.000
1.000
1.000
VRk,c [kN]
g M,c
V Rd,c [kN]
VSd [kN]
43.703
1.500
39.819
15.600
5. Combined tension and shear loads SOFA (fib (07/2011), section 10.3)
steel
concrete
a
bN
bV
Status
0.128
0.173
2.0
OK
0.357
0.392
1.5
46
OK
bN + bV <= 1
6. Displacements
The displacement of the highest loaded anchor should be calculated according to the relevant approval. The displacement due to hole
tolerances can be neglected, because this method assumes that no hole clearance between anchors and fixture is present. The characteristic
loads of the highest loaded anchor are
NSk
5.920 [kN]
VSk
5.780 [kN]
The acceptable anchor displacements depend on the fastened construction and must be defined by the designer!
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor ( c ) 2003-2009 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.co.uk
Company:
Specifier:
Address:
Phone I Fax:
E-Mail:
Page:
Project:
Sub-Project I Pos. No.:
Date:
4
Damac Twin Towers
5/4/2014
7. Warnings
The design method fib (07/2011) assumes that no hole clearance between the anchors and the fixture is present. This can be achieved by
filling the gap with mortar of sufficient sompressive strength (e.g. by using the Hilti Dynamic Set) or by other suitable means.
The compliance with current standards (e.g. EC3) is the responsibility of the user
Checking the transfer of loads into the base material is required in accordance with fib (07/2011)!
To avoid failure of the anchor plate the required thickness can be calculated in PROFIS Anchor. Load re-distributions on the anchors due to
elastic deformations of the anchor plate are not considered. The anchor plate is assumed to be sufficiently stiff, in order not to be deformed
when subjected to the loading!
The accessory list in this report is for the information of the user only. In any case, the instructions for use provided with the product have to be
followed to ensure a proper installation.
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor ( c ) 2003-2009 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.co.uk
Company:
Specifier:
Address:
Phone I Fax:
E-Mail:
Page:
Project:
Sub-Project I Pos. No.:
Date:
5
Damac Twin Towers
5/4/2014
8. Installation data
Anchor plate, steel: Anchor type and diameter: HSA-R, M16 hnom1
Profile: no profile
Installation torque: 0.080 kNm
Hole diameter in the fixture: df = 18 mm
Hole diameter in the base material: 16 mm
Plate thickness (input): 16 mm
Hole depth in the base material: 85 mm
Recommended plate thickness: not calculated
Minimum thickness of the base material: 140 mm
Cleaning: Manual cleaning of the drilled hole according to instructions for use is required.
Annular gap must be removed by e.g. filling the holes with mortar of sufficient compressive strength.
8.1. Required accessories
Cleaning
Manual blow-out pump
Drilling
Suitable Rotary Hammer
Properly sized drill bit
Setting
Dynamic set
Installation torque control bar with suitable
screw driver or torque wrench
Hammer
30.0
112.5
30.0
112.5
1
52.0
148.0
100.0
c -x
-
c +x
150
150
c -y
-
100.0
c +y
-
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor ( c ) 2003-2009 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.co.uk
Company:
Specifier:
Address:
Phone I Fax:
E-Mail:
Page:
Project:
Sub-Project I Pos. No.:
Date:
6
Damac Twin Towers
5/4/2014
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor ( c ) 2003-2009 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan