Академический Документы
Профессиональный Документы
Культура Документы
LAYOUT
The Grain Pump Conveyor can be used in many different ways and operation can vary from
installation to installation. Thought given to proper grain system layout prior to conveyor installation
can prevent later problems in the grain flow plan and avoid possible bottle-necks.
A layout should be made to determine the exact location of conveyor, inlets, outlets, power source,
support and mounting locations. Grain pumps are an EXCELLENT LONG LIFE SYSTEM. They generally
do not require significant repair parts or other maintenance.
Usage
Classification*
Standard Farm
Standard Farm with
upgrades
Commercial
Commercial with
upgrades
Annual
Operating
Hours
0 - 250
250 - 500
500 - 750
750 and greater
* Classification is dependent on
operating conditions and practices
ii
PLANNING A SYSTEM
1. Is there room for a row of bins (silos) plus the possibility for expansion? These systems tend to
last a long time. Consider your operating plan, location of controls, power distribution,
driveway, and turn around areas.
2. If planning a flat storage building, assure the building is capable of supporting the Full load of
the loop, grain, and catwalk (this load is in addition to your regional roof load requirements).
3. Can spouts be run to an adjoining storage area if desired?
4. If there is a dryer involved, consider separate conveyors from the wet holding to the dryer and
from the dryer to storage. This enables the grain pump to always be free for grain from the
field and keeps the low capacity, long continuous hours of use on less expensive conveyors.
5. Consider two drive-over dump receiving hoppers for grain pump systems that will have many
trucks or wagons dumping grain. This will result in more continuous operation which can
almost double capacity.
6. If larger/wider drive-over pits are desired consider the following:
a. The wider the inlet is for the drive-over pits, the deeper or taller it will need to be to
maintain angle of flow in the hopper. The options are to lower the tube or raise the
driveway.
b. To lower the tubes, spouts will have to be added to the inlets for the intermediate wells,
and the loop will have either a deeper trench or higher elevated bins.
c. If the drive is raised, carefully consider the ramp grade, load design, side personnel
access, safety rails, and overhead clearance.
7. A grain pump loop must have a climbable tower at each end and access to every overhead
drop. Catwalk can be considered for the full length, but it is generally not necessary if every bin
(silo) has a ladder extending to the overhead drop area. When catwalk is not used full length,
some catwalk may be needed to reach the drop over the driveway.
8. Every component of a grain pump loop system should end up located above grade to avoid
water issues that can rust the conveyors housing and chain. If located below ground level in a
trench or pit, adequate drainage to daylight or sump pump is required. Assure landscaping
diverts drainage away from pit; covers should be used over any open areas to shed water.
iii
9. When choosing a system size, consider capacity required now as well as into the future. These
units will handle a lot of grain before major parts replacement is necessary. The loop is
modular, as length can be added in the future up to the maximum designed length for the
particular system.
10. Plan for enough space between bin (silo) foundations to allow space for bin well controls (this is
outside space between bins). Concrete foundations, trenches and floors need to have
maintenance access and clearances considered in the design layout. Refer to the
equipment/component specifications to plan adequate space and clearances.
11. If concrete is placed before the system arrives, the corner support pads should be lower than
the bottom of the horizontal tubular housing; there are support feet on the bottom corners
(refer to the equipment specifications). Again, if concrete trenches or pits are utilized, assure
maintenance access is adequate.
12. Make sure there is suitable electrical power available. Single phase power may be used if HP
requirements allow.
13. Make sure amp meters are used so motor loads can be observed by the operator. Soft start
electrical motor starters are recommended.
14. Chain inspection ports are recommended. Utilize one inspection port between the drive-over
pit and the first loop corner to monitor physical tube fill. Utilize ports after each bin if possible.
Ports are for horizontal tubes only.
15. Chain access section kits are available for use on the horizontal tubes only.
13. Have an inspection port between the drive-over pit and the first bottom corner. If possible,
place one inspection port after each bin. Consider where to utilize chain access sections.
Hutchinson/Mayrath
NOTE:
10" (25.4 cm)
Model shown
SPECIFICATIONS
6'' (15.2 cm)
Maximum Capacity *
124
109
94
83
81X
81XHH
81X HH
81X HH
12 Tooth
14 Tooth
16 Tooth
22 Tooth
10.5 lbs./ft.
18 lbs./ft.
20 lbs./ft.
26.5 lbs./ft.
(14.9 kg/m)
(17.9 kg/m)
(22 kg/m)
(35.7 kg/m)
19.5 lbs./ft.
34 lbs./ft.
45 lbs./ft.
63 lbs./ft.
(28.3 kg/m)
(41.7 kg/m)
(59.5 kg/m)
(89.3 kg/m)
For Spout Components and Accessories not listed, refer to Custom Auger Section Spouting & Accessories Section or consult the factory.
0402046
01236A2
2014
Hutchinson/Mayrath
2014
Hutchinson/Mayrath
100'
(30.48 m)
Drive
Corner
40'
(12.19 m)
BIN A
BIN B
Inspection
Corner
90
Corner
LOWER HORIZONTAL LENGTH (Grain Movement)
20'
(6.10 m)
In this example, there is 40 ft. (12.19 m) of vertical conveyor and 120 ft. (36.58 m) of horizontal conveyor that will contain grain.
6'' (15.2 cm)
8 HP (5.9 kw)
6 HP (4.4 kw)
14 HP (10.4 kw)
20 HP (14.9 kw)
30 HP (22.3 kw)
14 HP (10.4 kw)
15 HP (11 kw)
25 HP (18.5 kw)
40 HP (30 kw)
60 HP (45 kw)
If there were plans to transfer grain from Bin A to Bin B, an additional 35 ft. (10.67 m) of horizontal length must be added to the calculation.
- 35' (10.67 m) x HP (kw) FACTOR =
01766A1
2014
Hutchinson/Mayrath
Description
5 HP (4 kw)
7 1/2 HP (5.5 kw)
10 HP (7.5 kw)
15 HP (11 kw)
20 HP (15 kw)
25 HP (18.5 kw)
30 HP (22 w)
Two 15 HP (11 kw) - One motor at each corner
List Price
$ 9,662.00
9,662.00
9,715.00
12,083.00
12,486.00
12,514.00
14,090.00
15,675.00
Description
5 HP (4 kw)
7 1/2 HP (5.5 kw)
10 HP (7.5 kw)
15 HP (11 kw)
20 HP (15 kw)
25 HP (18.5 kw)
30 HP (22 kw)
Two 15 HP (11 kw) - One motor at each corner
List Price
$ 10,814.00
10,814.00
10,814.00
13,237.00
13,639.00
13,706.00
15,242.00
16,828.00
Description
List Price
P061120
$ 1,094.00
P061130
1,424.00
P061139
1,917.00
P061140
1,894.00
2014
Hutchinson/Mayrath
Description
90 Discharge with Gate and Control Wheel
Ground Control Kit
Chain Style Ground Control Kit
Electric Control Kit for Drop - 115-208/230V, 60 Hz, 1 PH
Electric Control Kit for Drop - 220V, 50 Hz, 1PH
Electric Control Kit for Drop - 575V, 60 Hz, 3 PH
Electric Control Kit for Drop - 208-230/460V, 60 Hz, 3 PH
Electric Control Kit for Drop - 115-208/230V, 60 Hz, 1 PH, Explosion proof motor
Electric Control Kit for Drop - 208-230/460V, 60 Hz, 3 PH, Explosion proof motor
List Price
$ 1,684.00
300.00
577.00
2,460.00
2,616.00
2,460.00
2,460.00
3,158.00
3,158.00
Description
List Price
PA061501
$261.00
PA061502
*Intermediate Well
226.00
PA061503
240.00
PA061601
156.00
PA061602
109.00
PA061604
1,170.00
PA061605
1,020.00
Description
List Price
P061210
Hopper 42 1/2'' (1.08 m) long with 6'-0" (1.83 m) of tubular housing and two
sections of drive-over grating
Hopper 42 1/2'' (1.08 m) long with 6'-0" (1.83 m) of tubular housing and
safety screen
Hopper 62 1/2'' (1.59 m) long with 7'-8'' (2.34 m) of tubular housing and three
sections of drive-over grating
Hopper 62 1/2'' (1.59 m) long with 7'-8" (2.34 m) of tubular housing and
safety screen
Hopper 102 1/2'' (2.60 m) long with 11'-0" (3.35 m) of tubular housing and five
sections of drive-over grating
Hopper 102 1/2'' (2.60 m) long with 11'-0" (3.35 m) of tubular housing and
safety screen
$ 1,562.00
P061211
P061220
P061221
P061230
P061231
1,122.00
2,029.00
1,440.00
2,945.00
1,761.00
2014-3
Hutchinson/Mayrath
Description
15 HP (11 kw)
20 HP (15 kw)
30 HP (22 kw)
40 HP (30 kw)
Two 15 HP (11 kw) - One motor at each corner
Two 20 HP (15 kw) - One motor at each corner
Two 30 HP (22 kw) - One motor at each corner
List Price
$12,950.00
13,377.00
14,711.00
17,455.00
18,695.00
19,549.00
22,282.00
List Price
$13,978.00
14,407.00
15,740.00
18,484.00
19,723.00
20,578.00
23,309.00
Description
15 HP (11 kw)
20 HP (15 kw)
30 HP (22 kw)
40 HP (30 kw)
Two 15 HP (11 kw) - One motor at each corner
Two 20 HP (15 kw) - One motor at each corner
Two 30 HP (22 kw) - One motor at each corner
Description
20' (6.10 m) long section
30' (9.14 m) long section
39 (11.89 m) long section
40 (12.19 m) long section
List Price
$1,382.00
2,027.00
2,700.00
2,677.00
2014
Hutchinson/Mayrath
Description
90 Discharge with 29" Gate opening, Control Wheel, 8' of tube
90 Discharge with 54" Gate opening, Control Wheel, 12'-6" of tube
Ground Control Kit for 29" Gate opening
Ground Control Kit for extended length drops
Chain Style Ground Control Kit
Electric Control Kit for Drop - 115-208/230V, 60 Hz, 1PH
Electric Control Kit for Drop - 220V, 50 Hz, 1PH
Electric Control Kit for Drop - 575V, 60 Hz, 3PH
Electric Control Kit for Drop - 208-230/460V, 60 Hz, 3PH
Electric Control Kit for Drop - 115-208/230V, 60 Hz, 1PH, Explosion proof motor
Electric Control Kit for Drop - 208-230/460V, 60 Hz, 3PH, Explosion proof motor
List Price
$2,101.00
2,967.00
300.00
300.00
577.00
2,460.00
2,616.00
2,460.00
2,460.00
3,158.00
3,158.00
Description
* Center Well 18'' (45.7 cm) lg. w/Rollers, removable flange
* Intermediate Well w/Rollers - 13 (33.0 cm) wide
* Rack and Pinion for 18 (45.7 cm) lg. Wells
Flat Storage Well w/Grating, 115-208/230V, 60 Hz, 1PH
Flat Storage Well w/Grating, 115-208/230V, 60 Hz, 1PH, Explosion Proof Motor
Flat Storage Well w/Grating, 208-230/460V, 60 Hz, 3PH
Flat Storage Well w/Grating, 208-230/460V, 60 Hz, 3PH, Explosion Proot Motor
8 (20.3 cm) Half-Band w/Inspection Port
8 (20.3 cm) Inlet Hopper
Chain Access Section x 5 (1.5 m)
Chain Access Section x 3 (.91m)
List Price
$ 364.00
280.00
275.00
4,335.00
5,034.00
4,335.00
5,034.00
173.00
141.00
1,350.00
1,195.00
Description
Hopper 42-1/2'' (1.08 m) long with 6'-0" (1.83 m) of tubular housing and two sections of drive-over grating
Hopper 42-1/2'' (1.08 m) long with 6'-0" (1.83 m) of tubular housing and safety screen
Hopper 62-1/2'' (1.59 m) long with 7'-8'' (2.34 m) of tubular housing and three sections of drive-over grating
Hopper 62-1/2'' (1.59 m) long with 7'-8'' (2.34 m) of tubular housing and safety screen
Hopper 102-1/2'' (2.60 m) long with 11'-0" (3.35 m) of tubular housing and five sections of drive-over grating
Hopper 102-1/2'' (2.60 m) long with 11'-0" (3.35 m) of tubular housing and safety screen
Hopper 102-1/2'' (2.60 m) long with 11'-0" (3.35 m) of tubular housing and five sections of drive-over grating
with electric rack and pinion 115-208/230V, 60 Hz, 1 PH
Hopper 102-1/2'' (2.60 m) long with 11'-0" (3.35 m) of tubular housing and five sections of drive-over grating
with electric rack and pinion 110-220V, 50 Hz, 1 PH
Hopper 102-1/2'' (2.60 m) long with 11'-0" (3.35 m) of tubular housing and five sections of drive-over grating
with electric rack and pinion 115-208/230V, 60 Hz, 1 PH, Explosion Proof Motor
Hopper 125'' (3.18 m) long with 12'-11" (3.94 m) of tubular housing and six sections of drive-over grating.
Hopper 125'' (3.18 m) long with 12'-11" (3.94 m) of tubular housing and safety screen
Hopper 145'' (3.68 m) long with 14'-0" (4.27 m) of tubular housing and seven sections of drive-over grating.
Band-on Hopper x 30 (76.2 cm) long with a bolt-on cover.
List Price
$1,768.00
1,346.00
2,308.00
1,637.00
3,159.00
2,115.00
7,922.00
7,991.00
7,756.00
4,107.00
2,668.00
4,354.00
386.00
2014-2
Hutchinson/Mayrath
Catalog No.
Description
P1014120
20 HP (15 kw)
$ 15,099.00
P1014130
30 HP (22 kw)
16,485.00
P1014140
40 HP (30 kw)
19,057.00
P1014150
50 HP (37 kw)
19,780.00
P1014220
20,777.00
P1014230
23,158.00
P1014240
28,125.00
P1014250
29,273.00
Description
List Price
P1014120-TU
$16,047.00
P1014130-TU
17,328.00
P1014140-TU
20,007.00
P1014150-TU
20,727.00
P1014220-TU
21,727.00
P1014230-TU
24,106.00
P1014240-TU
29,062.00
P1014250-TU
30,210.00
Description
List Price
P101120
$1,690.00
P101130
2,473.00
P101139
3,382.00
P101140
3,358.00
2014-3
Hutchinson/Mayrath
Description
90 Discharge with 29" Gate option and Control Wheel, 8' of tube
90 Discharge with 54 Gate option, Control Wheel, 12'-6" of tube
Ground Control Kit for 29" Gate option
Ground Control Kit for extended length drops
Chain Style Ground Control Kit
Electric Control Kit for Drop - 115-208/230V, 60 Hz, 1 PH
Electric Control Kit for Drop - 220V, 50 Hz, 1 PH
Electric Control Kit for Drop - 575V, 60 Hz, 3 PH
Electric Control Kit for Drop - 208-230/460V, 60 Hz, 3 PH
Electric Control Kit for Drop - 115-208/230V, 60 Hz, 3 PH, Explosion proof motor
Electric Control Kit for Drop - 208-230/460V, 60 Hz, 3 PH, Explosion proof motor
List Price
$ 2,322.00
3,516.00
300.00
300.00
577.00
2,460.00
2,616.00
2,460.00
2,460.00
3,158.00
3,158.00
Description
*Center Well 18" (45.7 cm) long with Rollers (for 13 floors)
*Intermediate Well with Rollers (for 13 floors)
*Rack and Pinion Controls for Wells w/18 (45.7 cm) Travel (for 13 floors)
10 (25.4 cm) Half-Band w/Inspection Port
10 (25.4 cm) Inlet Hopper
Inspection Port w/Back Band 12 x 12 (30.5 cm x 30.5 cm)
Chain Access Section x 5 (1.52 m)
Chain Access Section x 3 (.91 m)
Flat Storage Well w/grating, 115-208/230V, 60 Hz, 1 PH
Flat Storage Well w/grating, 110-220V, 50 Hz, 1 PH
Flat Storage Well w/grating, 208-230/460V, 60 Hz, 3 PH,
Flat Storage Well w/grating, 115-208/230V, 60 Hz, 1 PH, Explosion proof motor
Flat Storage Well w/grating, 208-230/460V, 60 Hz, 3 PH, Explosion proof motor
Inlet Hopper w/Back Band, 18 lg. (45.7 cm) - 10 Ga. (3.43 mm)
Inlet Hopper w/Back Band, 36 lg. (91.4 cm) - 10 Ga. (3.43 mm)
List Price
$433.00
352.00
489.00
198.00
227.00
213.00
1,445.00
1,305.00
4,822.00
5,047.00
4,822.00
5,497.00
5,497.00
347.00
694.00
*NOTE: The center well, intermediate wells and rack & pinion are meant to be used only with the control pipe kits below.
Bin Dia.
PA101510
PA101511
PA101512
PA101513
PA101514
PA101515
PA101516
PA101517
PA101518
PA101519
PA101520
PA101521
24' (7.32 m)
27' (8.23 m)
30' (9.14 m)
33'-34' (10.06-10.36 m)
36' (10.97 m)
37'-39' (11.28-11.89 m)
40' (12.19 m)
42' (12.80 m)
48'-49' (14.63-14.94 m)
54'-55' (16.46-16.76 m)
60' (18.29 m)
63' (19.20 m)
Weight
21.5 lbs. (10 kg)
33.5 lbs. (15 kg)
38 lbs. (17 kg)
43.5 lbs. (20 kg)
50.5 lbs. (23 kg)
55.5 lbs. (25 kg)
58 lbs. (26 kg)
60 lbs. (27 kg)
70 lbs. (32 kg)
79.5 lbs. (36 kg)
87 lbs (39 kg)
91.5 lbs. (42 kg)
List Price
Catalog No.
$176.00
$187.00
$198.00
$203.00
$211.00
$224.00
$242.00
$258.00
$365.00
$459.00
$480.00
$494.00
PA101522
PA101523
PA101524
PA101525
PA101526
PA101527
PA101528
PA101529
PA101530
PA101531
PA101532
Bin Dia.
68'-69' (20.73-21.03 m)
72' (21.95 m)
75' (22.86 m)
78' (23.77 m)
80' (24.38 m)
82' (24.99 m)
90' (27.43 m)
92' (28.04 m)
105' (32.00 m)
113' (34.44 m)
120' (36.58 m)
Weight
96.5 lbs. (44 kg)
101 lbs. (46 kg)
104.5 lbs. (47 kg)
113 lbs. (51 kg)
113.5 lbs. (51 kg)
119 lbs. (54 kg)
131.5 lbs. (60 kg)
139.5 lbs. (63 kg)
157.5 lbs. (71 kg)
169 lbs. (77 kg)
187.5 lbs. (85 kg)
List Price
$ 521.00
$ 525.00
$ 531.00
$ 559.00
$ 571.00
$ 589.00
$ 721.00
$ 782.00
$ 874.00
$ 903.00
$ 933.00
2014-2
Hutchinson/Mayrath
List Price
$410.00
340.00
325.00
Description
*Center Well 18" (45.7 cm) long with Rollers (for 15 floors)
*Intermediate Well with Rollers (for 15 floors)
*Rack and Pinion Controls for Wells w/18 (45.7 cm) Travel (for 15 floors)
*NOTE: The center well, intermediate wells and rack & pinion are meant to be used only with the control pipe
kits below.
Catalog No.
B1124A
B1127A
B1130A
B1133A
B1136A
Bin Dia.
23-25
26'-28
29-31
33'
36'
Weight
(7 m - 7.62 m)
(7.92 m - 8.53 m)
(8.84 m - 9.45 m)
(10.06 m)
(10.97 m)
List Price
Catalog No
$146.00
$161.00
$170.00
$186.00
$212.00
B1142A
B1148A
B1154AC
B1160A
Bin Dia.
42'
48'
54'
60'
(12.80 m)
(14.63 m)
(16.46 m)
(18.29 m)
Weight
List Price
$ 246.00
$ 270.00
$ 331.00
$ 369.00
9A
List Price
$1,904.00
1,604.00
2,385.00
1,848.00
3,483.00
2,515.00
4,578.00
2,716.00
10,247.00
2014
Hutchinson/Mayrath
Description
One 30 HP (22 kw)
One 40 HP or 50 HP (30 kw or 37 kw)
One 60 HP (45 kw)
Two 40 HP or 50 HP (30 kw or 37 kw)
Two 60 HP (45 kw)
List Price
$27,194.00
30,858.00
33,482.00
39,878.00
45,677.00
Description
One 30 HP (22 kw)
One 40 HP or 50 HP (30 kw or 37 kw)
One 60 HP (45 kw)
Two 40 HP or 50 HP (30 kw or 37 kw)
Two 60 HP (45 kw)
List Price
$28,004.00
31,631.00
34,235.00
40,867.00
46,666.00
Description
20' (6.10 m) long section
30' (9.14 m) long section
39' (11.89 m) long section
40' (12.19 m) long section
List Price
$ 2,488.00
3,634.00
4,810.00
4,787.00
Description
List Price
P121310
$ 4,333.00
P121320
6,378.00
PA001602
300.00
PA001609
577.00
PA001603
2,460.00
PA001604
2,616.00
PA001605
2,460.00
PA001606
2,460.00
PA001607
Electric Control Kit for Drop - 115-208/230V, 60 Hz, 3 PH, Explosion proof motor
3,158.00
PA001608
Electric Control Kit for Drop - 208-230/460V, 60 Hz, 3 PH, Explosion proof motor
3,158.00
10
2014
Hutchinson/Mayrath
List Price
PA121502
PA121503
458.00
PA121505
433.00
PA121506
2,074.00
PA121507
110.00
PA121601
224.00
PA121602
295.00
PA121605
839.00
PA121509
1,783.00
PA121603
12 (30.5 cm) Inspection Port w/Back Band (14 x 14) (366 cm x 36-6 cm)
PA121604
1,745.00
PA121606
1,560.00
PA121511
4,681.00
PA121512
4,681.00
PA121513
Flat Storage Well w/grating, 115-208/230V, 60 Hz, 1 PH, Explosion proof motor
5,379.00
PA121514
Flat Storage Well w/grating, 208-230/460V, 60 Hz, 3 PH, Explosion proof motor
5,379.00
$ 523.00
241.00
NOTE: For control pipes, use kits from commercial grain pump section.
Description
P121210
$2,828.00
P121212
2,197.00
P121213
5,655.00
P121214
2,067.00
P121230
4,634.00
P121240
5,595.00
P121253
11,134.00
P121255
11,134.00
P121256
11,842.00
P121257
11,842.00
List Price
11
2014-3
Hutchinson/Mayrath
42-1/16" (1.07 m)
42-1/2" (1.08 m)
54" (1.37 m)
42 7/8" (1.09 m)
50 7/8" (1.29 m)
52 3/8" (1.33 m)
66" (1.68 m)
16-1/2''(41.9 cm)
40 13/16" (1.04 m)
48 7/8" (1.24 m)
50 1/8" (1.27 m)
63" (1.60 m)
40 13/16" (1.04 m)
48-3/4" (1.24 m)
50-1/4" (1.28 m)
63" (1.60 m)
42 1/2" (1.08 m)
42 1/2" (1.08 m)
54" (1.37 m)
57-1/4'' (1.45 m)
68-1/2" (1.74 m)
68-1/2" (1.74 m)
86" (2.18 m)
42 1/2" (1.08 m)
42 1/2" (1.08 m)
54" (1.37 m)
INSPECTION CORNER
90 DISCHARGE
with GATE
8-0 (2.44 m)
8-0 (2.44 m)
8-0 (2.44 m)
12-0 (3.66 m)
*12-6 (3.81 m)
*12-6 (3.81 m)
*15-0 (4.57 m)
*11-5 (3.48 m)
44-1/4" (1.12 m)
53-5/8" (1.36 m)
61-1/8" (1.55 m)
68" (1.73 m)
48" (1.22 m)
66-1/8" (1.68 m)
69-13/16" (1.77 m)
71-1/8" (1.81 m)
72" (1.83 m)
Discharge
74" (1.88 m)
78-11/16" (2.00 m)
81" (2.06 m)
84-1/4" (2.14 m)
48-1/2" (1.23 m)
60-1/4" (1.53 m)
61-1/8" (1.55 m)
75" (1.91 m)
Opening
02795A2
02784A2
02921A1-B
02827A2
12
2014
Hutchinson/Mayrath
17-5/8''
(44.8 cm)
35-3/4
(90.8 cm)
14-3/4
(37.5 cm)
72 (1.83 m)
92 (2.34 m)
132 (3.35 m)
155 (3.94 m)
172 (4.37 m)
168 (4.27 m)
END VIEW
SIDE VIEW
Height of Hopper
With Grating Installed A
With Screen Installed B
C
To Flange
Note: For concrete dimensions, see Page 9 in Mass-Ter Mover Conveyor section.
* INTERMEDIATE WELL
*CENTER WELL
TOP VIEW
TOP VIEW
02828A3
02845A1
02799A2
02800A2
13
2014
Hutchinson/Mayrath
DOUBLE RUN
SPECIFICATIONS
DOUBLE RUN SYSTEM
6" round
Dimensions of
(15.2
cm)
Conveying chamber
1500 BPH (41 TPH)
Maximum Capacity *
338 FPM (103.02 MPM)
Chain Travel
126
Head Shaft RPM
14 (1.9 mm)
Housing Gauge Galv. **
3/8" (10 mm)
Paddles UHMW
1 1/2" (38 mm)
Head Shaft Dia.
1 1/2" (38 mm)
Boot Shaft Dia.
81X
Conveyor Chain
12 Tooth
Conveyor Sprocket
10" round
8" round
(25.4 cm)
(20.3 cm)
6000 BPH (162 TPH)
4000 BPH (108 TPH)
329 FPM (100.28 MPM) 348 FPM (106.07 MPM)
114
126
12 (2.66 mm)
14 (1.9 mm)
1/2" (13 mm)
3/8" (10 mm)
2" (51 mm)
2" (51 mm)
2" (51 mm)
2" (51 mm)
81XHH
81X
14 Tooth
12 Tooth
12" round
(30.5 cm)
10,000 BPH (270 TPH)
400 FPM (122 MPM)
102
10 (3.43 mm)
1/2" (13 mm)
3-7/16" (87 mm)
3-7/16" (87 mm)
81XHH
18 Tooth
CROSS SECTION
OF HOUSING
02860A1
14
2014
Hutchinson/Mayrath
DOUBLE RUN
8
4
1
REF. NO.
Motor Pulley Not Included with Standard Boot with Drive Use 4" (10.2 cm) O.D. Sheave.
Motor Pulley Is Included with Head Section with Reducer Drive.
DESCRIPTION
CATALOG NO.
WEIGHT
LIST PRICE
P2642C4
$ 3,230.00
P2641C4
$ 1,446.00
HEAD SECTION w/Reducer Drive* (Drive preassembled at factory) Motor Pulley Included
2
2
2
P2653C4R
P2654C4R
P2655C4R
$ 4,245.00
5,150.00
6,128.00
BOOT SECTION * (Less Drive) For use with Head Section w/Reducer Drive
1
P2646C4
$ 2,364.00
P2605C4
P2610C4
P2620C4
P2632C4
769.00
1,120.00
2,127.00
3,196.00
4
--
Incline Hopper
Cover
P2650A
P2651A
257.00
136.00
5
6
7
8
9
OUTLET COMPONENTS
Head Discharge Spout 90
Head Discharge Spout 45
Intermediate Drop w/Gate
Rack & Pinion
Intermediate Loop Style Drop (for Horizontal use only)
P2667A
P2668A
P1648A
P1650A
P2657A
17 lbs. (8 kg)
16 lbs. (7 kg)
56 lbs. (25 kg)
17 lbs. (8 kg)
135 lbs. (61 kg)
176.00
240.00
454.00
300.00
1,371.00
---
MISC. COMPONENTS
Chain Access Section x 3 (.91 m) long, band-on
Chain Access Section x 5 (1.52 m) long, band-on
P2686A
P2687A
585.00
710.00
* Indicates items that include chain, paddles and two connecting bands. Paddles are shipped assembled.
02253A1
0402325
15
2014-2
Hutchinson/Mayrath
DOUBLE RUN
Motor Pulley not Included with Standard Boot with Drive Use 4.2" (10.7 cm) P.D. Sheave for 8 (20.3 cm) Pump.
Motor Pulley is included with Head Section with Reducer Drive.
REF. NO.
DESCRIPTION
CATALOG NO.
WEIGHT
LIST PRICE
STANDARD BOOT SECTION * (Less Drive) For use with Head Section w/Reducer Drive
Standard Boot (Less Drive)
$
P2846C4
360 lbs. (163 kg)
Standard Boot w/Drop Through
P2846C4DT 386 lbs. (175 kg)
Non-Inlet Boot (Less Drive)
165 lbs. (75 kg)
P2847C4
4
4A
5
5A
*6
7
P2870A
P0805A
P2871A
P0806A
P2882C4
P2881A
31 lbs.
31 lbs.
32 lbs.
42 lbs.
220 lbs.
100 lbs.
(14 kg)
(14 kg)
(15 kg)
(19 kg)
(100 kg)
(45 kg)
2,708.00
2,980.00
1,817.00
$ 152.00
149.00
100.00
134.00
1,174.00
476.00
1
1
1
1
1
1
1
P2890C4
P2891C4
P2892C4
P2893C4
P2894C4
P2895C4
P2896C4
900 lbs.
905 lbs.
925 lbs.
840 lbs.
840 lbs.
880 lbs.
910 lbs.
(408 kg)
(411 kg)
(420 kg)
(381 kg)
(381 kg)
(399 kg)
(413 kg)
$6,293.00
6,293.00
6,469.00
6,257.00
6,257.00
6,904.00
7,556.00
Wide boot with drop-through outlet and drive: Add DT to Catalog No., i.e. P2892C4DT. Add $275.00 to List Price.
Wide boot with drop-though outlet does not include spout; select head discharge spout from Page 16A to bolt on to outlet.
If rack & pinion control with gate is desired, use P2851A.
1
1
WIDE BOOT SECTION * (Less Drive) For use with Head Section w/Reducer Drive
8 Wide Boot (less drive)
P2897C4
595 lbs. (270 kg) $3,644.00
8 Wide Boot w/Drop Through
P2897C4DT
575 lbs. (261 kg) 3,928.00
Wide boot with drop-though outlet does not include spout; select head discharge spout from Page 16A to bolt on to outlet.
If rack & pinion control with gate is desired, use P2851A.
4
4A
5
5A
P2872A
P2873A
P2874A
P2875A
56 lbs.
40 lbs.
35 lbs.
36 lbs.
(25 kg)
(18 kg)
(16 kg)
(16 kg)
$ 153.00
153.00
101.00
101.00
Multiple tall hoppers can be stacked or tapered hopper added to full hopper(s).
* Indicates items that include chain, paddles and two connecting bands. Paddles are shipped assembled.
0400487-6
16
2014-3
Hutchinson/Mayrath
DOUBLE RUN
DESCRIPTION
CATALOG NO.
P2841C4
WEIGHT
160 lbs.
(73 kg)
LIST PRICE
$ 1,466.00
HEAD SECTION w/Reducer Drive* (Drive preassembled at factory) Motor Pulley Included
2
2
2
2
P2853C4R
P2854C4R
P2855C4R
P2856C4R
305 lbs.
325 lbs.
370 lbs.
432 lbs.
(138 kg)
(147 kg)
(168 kg)
(196 kg)
P2805C4
P2810C4
P2820C4
P2832C4
140 lbs.
240 lbs.
430 lbs.
670 lbs.
(64 kg)
(109 kg)
(195 kg)
(304 kg)
$ 4,274.00
5,160.00
6,120.00
7,667.00
847.00
1,357.00
2,333.00
3,609.00
OUTLET COMPONENTS
8
9
10
11
11A
11B
12
13
P2867A
P2866A
P2868A
P2837A
P2857A
P2858A
P1850A
P2851A
36 lbs.
34 lbs.
34 lbs.
67 lbs.
160 lbs.
156 lbs.
20 lbs.
70 lbs.
(16 kg)
(15 kg)
(15 kg)
(30 kg)
(73 kg)
(71 kg)
(9 kg)
(32 kg)
$ 191.00
215.00
273.00
442.00
1,693.00
1,693.00
261.00
1,143.00
P2886A
P2887A
102 lbs.
154 lbs.
(46 kg)
(70 kg)
$ 585.00
710.00
MISC. COMPONENTS
---
16A
2014-3
Hutchinson/Mayrath
DOUBLE RUN
DESCRIPTION
CATALOG NO.
WEIGHT
LIST PRICE
1
1
1
P3043C4
P3044C4
P3045C4
736 lbs.
746 lbs.
875 lbs.
(334 kg)
(338 kg)
(397 kg)
$ 4,132.00
4,258.00
6,820.00
**Standard Boot with drop-through gated outlet and drive: Add DT to Catalog Number, i.e. P3043C4DT.
Add $334.00 to List Price. DT add 30 lbs. (14 kg) on 10.
STANDARD BOOT SECTION * (Less Drive) For use with Head Section w/Reducer Drive
Standard Boot (Less Drive)
P3046C4
490 lbs. (222 kg)
P3046C4DT
Standard Boot w/Drop Through
520 lbs. (236 kg)
P3047C4
Non-Inlet Boot (Less Drive)
277 lbs. (126 kg)
1
1
1A
4
4A
5
5A
6
7
P3070A
P3072A
P3071A
P3073A
P3082C4
P3081A
37 lbs.
35 lbs.
28 lbs.
48 lbs.
350 lbs.
142 lbs.
(17 kg)
(16 kg)
(13 kg)
(22 kg)
(159 kg)
(64 kg)
$ 2,898.00
3,228.00
2,055.00
168.00
197.00
140.00
159.00
1,398.00
515.00
1
1
1
1
1
1
1
P3090C4
P3091C4
P3092C4
P3093C4
P3094C4
P3095C4
P3096C4
$6,510.00
6,610.00
7,041.00
7,419.00
8,185.00
9,076.00
10,464.00
Wide boot with drop-through outlet and drive: Add DT to Catalog No., i.e. P3092C4DT. Add $334.00 to List Price.
Select Head discharge spout from next page to bolt on to outlet. If rack & pinion control with gate is desired, use P3051A.
1
1
WIDE BOOT SECTION * (Less Drive) For use with Head Section w/Reducer Drive
10 Wide Boot (less drive)
P3097C4
830 lbs. (376 kg)
10 Wide Boot w/Drop Through
P3097C4DT
830 lbs. (376 kg)
4
4A
5
5A
P3077A
P3079A
P3078A
P3080A
61 lbs.
43 lbs.
41 lbs.
42 lbs.
(28 kg)
(20 kg)
(19 kg)
(19 kg)
$3,830.00
4,176.00
$ 167.00
190.00
135.00
153.00
Multiple tall hoppers can be stacked or tapered hopper added to full hopper(s)
* Indicates items that include chain, paddles and two connecting bands.
0400487-4
17
Hutchinson/Mayrath
DOUBLE RUN
REF. NO.
DESCRIPTION
CATALOG NO.
2
2
P3041C4
P3042C4
WEIGHT
262 lbs.
277 lbs.
(119 kg)
(126 kg)
LIST PRICE
$ 1,661.00
2,352.00
HEAD SECTION with Reducer Drive* (Drive preassembled at factory) Motor Pulley Included
Motor Pulley is included with Head Section with Reducer Drive.
2
2
2
2
2
2
3
3
3
3
P3054C4R
P3055C4R
P3056C4R
P3057C4R
P3058C4R
P3061C4R
430 lbs.
480 lbs.
536 lbs.
546 lbs.
626 lbs.
637 lbs.
(195 kg)
(218 kg)
(243 kg)
(248 kg)
(284 kg)
(289 kg)
$ 5,354.00
6,314.00
7,505.00
7,857.00
9,719.00
10,030.00
P3005C4
P3010C4
P3020C4
P3030C4
250 lbs.
425 lbs.
755 lbs.
1100 lbs.
(113 kg)
(193 kg)
(342 kg)
(499 kg)
$ 1,329.00
2,151.00
3,670.00
5,212.00
P3067A
P3066A
P3068A
P3057A
P3058A
P2050A
P3051A
45 lbs.
47 lbs.
48 lbs.
176 lbs.
172 lbs.
24 lbs.
84 lbs.
(20 kg)
(21 kg)
(22 kg)
(80 kg)
(78 kg)
(11 kg)
(38 kg)
$ 197.00
211.00
211.00
1,693.00
1,693.00
285.00
1,201.00
P3086A
P3087A
112 lbs.
170 lbs.
(51 kg)
(77 kg)
$ 585.00
710.00
OUTLET COMPONENTS
8
9
10
11
11A
12
13
---
* Indicates items that include chain, paddles and two connecting bands.
0400487-4
18
2014-2
Hutchinson/Mayrath
DOUBLE RUN
Motor Pulley is included with Standard Boot with Drive Motor Pulley is included with Head Section with Reducer Drive.
REF. NO.
DESCRIPTION
CATALOG NO.
WEIGHT
LIST PRICE
2
2
2
2
HEAD SECTION w/Reducer Drive* (Drive preassembled at factory) Motor Pulley Included
$ 8,607.00
P3255C4R
770 lbs. (349 kg)
Electric Drive, 20 HP (15 kw)
9,621.00
P3256C4R
865 lbs. (392 kg)
Electric Drive, 30 HP (22 kw)
11,499.00
P3257C4R
990 lbs. (449 kg)
Electric Drive, 50 HP (37 kw)
Contact Factory
P3258C4R
Electric Drive, 60 HP (45 kw)
P3241C4
$ 3,588.00
1
1
1A
BOOT SECTION * (Less Drive) For use with Head Section w/Reducer Drive
Standard Boot (Less Drive)
P3247C4
750 lbs. (340 kg)
Standard Boot w/Drop Through
P3247C4DT 790 lbs. (358 kg)
Non-Inlet Boot (Less Drive)
505 lbs. (229 kg)
P3248C4
$ 5,098.00
5,564.00
3,711.00
3
3
3
3
P3205C4
P3210C4
P3220C4
P3230C4
$ 1,796.00
3,114.00
5,008.00
7,170.00
4
5
6
7
*8
9
INLET COMPONENTS
Tapered Hopper Extension
Cover for Tapered Hopper
Tall Hopper Extension
Cover for Tall Extension (will fit boot w/o hopper also)
By-Pass Inlet
Intermediate Inlet (for use on bottom tubes only)
P3270A
P3271A
P3272A
P3273A
P3282C4
P3281A
181.00
165.00
295.00
112.00
2,064.00
625.00
P3266A
P3266A-SF
P3267A
P3268A
P3257A
P3258A
H2242A
P3251A
235.00
312.00
269.00
285.00
2,966.00
2,966.00
360.00
1,123.00
P3286A
P3287A
OUTLET COMPONENTS
10
-11
12
13
13A
14
15
---
$ 585.00
710.00
* Indicates items that include chain, paddles and two connecting bands. Paddles are shipped assembled.
0401604-3
19
2014-3
Hutchinson/Mayrath
DOUBLE RUN
Angle of Operation
Horsepower per foot
(kw per meter)
Horizontal
.042
(.102)
15
.062
(.151)
30
.085
(.207)
45
.120
(.292)
60
.140
(.341)
Angle of Operation
Horsepower per foot
(kw per meter)
Horizontal
.076
(.185)
15
.113
(.275)
30
.167
(.407)
45
.222
(.541)
60
.270
(.658)
Angle of Operation
Horsepower Per Foot
(kw per meter)
Horizontal
.114
(.278)
15
.170
(.414)
30
.250
(.610)
45
.333
(.812)
60
.405
(.988)
Angle of Operation
Horsepower Per Foot
(kw per meter)
Horizontal
.18
(.439)
20
15
.268
(.654)
30
.397
(.968)
45
.524
(1.278)
60
.629
(1.534)
2014
Hutchinson/Mayrath
DOUBLE RUN
HEAD SECTION
TUBE HOUSING
Includes Two Connecting Bands
SIDE VIEW OF
STANDARD BOOT
WITH DRIVE
SPOUTS
6 Model
8, 10 & 12
Model
G
A
B
E
F
3'-3"
(99.1 cm)
19"
(48.3 cm)
3'
(91.4 cm)
02254A1-B
01300A4
02255A1
02254A1-A
0400490-1
01765A2
21
2014