Академический Документы
Профессиональный Документы
Культура Документы
221
PXC64-U
DESIGO PX
Automation stations
modular model
CA1N9221en_09
2013-02-07
PXC...-U
Building Technologies
Functions
These freely programmable automation stations provide the infrastructure for the
provision and processing of system-specific and application-specific functions.
Apart from the freely programmable control functions these units comprise integrated
convenient management functions such as:
Alarm management with alarm routing throughout the whole network. Three level
alarm management (simple, basic and enhanced) with safety control transmission
and automatic transmission monitoring
Time schedulers
Trend functions
Remote management functions
Access protection for the whole network with individually defined user profiles and
categories
Programming language
These automation stations are freely programmable with the D-MAP programming
language (follows closely CEN Standard 1131). All function blocks available in libraries
are graphically linked with the plant operating programs.
Communication
BACnet / IP
BACnet / LonTalk
The devices communicate via an open LonTalk system in accordance with the international standard BACnet protocol. Both peer-to-peer communications with other
automation stations and connections to the PXM20 operator units are supported.
BACnet / PTP
The devices communicate via the public telephone network in accordance with the
international standard BACnet protocol.
Types
Automation stations
Automation station for up to 200 TX-I/O data points
Automation station for over 200 TX-I/O data points
Connecting cable (to connect an operator unit PXM10 or PXM20
and for Firmware download)
Type
PXC64-U
PXC128-U
PXA-C1
System controllers
System controller for the integration of DESIGO RXB room
controllers and KNX 3rd party devices
System controller for the Integration of M-Bus, Modbus and SCL
(up to 100 data points)
(up to 400 data points)
(SCL: up to 1000 data points, M- Bus and Modbus: up to 2000)
Type
PXC00-U
+ PXA30-K11
PXC00-U
+ PXA30-RS
+ PXA30-RS1
+ PXA30-RS2
Type
PXC00-U
+ PXA30-W1 / W2
Automation station (up to 200 TX-I/O data points) with Web
PXC64-U
function for BACnet/LonTalk segment
+ PXA30-W1 / W2
Automation station (over 200 TX-I/O data points) with Web function PXC1280-U
for BACnet/LonTalk segment
+ PXA30-W1 / W2
2/12
Siemens
Building Technologies
CA1N9221en_09
2013-02-07
Compatibility
NT
W1
W2
W0
N9261
N9262
N9263
N9264
N9265
N9266
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X 2)
X 2)
X
X
Function
Data sheet
Interfaces
Ethernet RJ45
Serial RS232
Network functions
Configuration network RJ45
BACnet / IP operation RJ45
BACnet / LonTalk operation
PTP Dial-in XWORKS plus RS232 1)
PPP Remote configuration RS232 1)
Remote management
PTP Dial-in Desigo Insight RS232 1)
PPP via Ethernet RJ45 1)
Web-Functions
Generic web functions
Graphic web functions
Send alarms via SMS (RS232)
Send alarms via E-Mail (RJ45)
1)
2)
X
X
PXA30-K11
PXA30-RS
PXA30-RS1
PXA30-RS2
N9281
N9281
N9281
X
X
X
X
X
X
100 DP
100 DP
100 DP
400 DP
400 DP
400 DP
2000 DP
2000 DP
1000 DP
Function
Data sheet
N9280
Interfaces
X
KNX interface
Serial RS232
Seral RS485
Network functions
Integration of RXB / RXL
Integration of KNX 3rd party devices
Integration of M-Bus counters
Integration of Modbus
Integration of SCL
X
X
3/12
Siemens
Building Technologies
CA1N9221en_09
2013-02-07
TX-I/O-Modules
Device
Digital input modules,
8 or 16 I/O points
Universal module
without / with local override facility and LCD
Super universal module without / with local override facility and LCD
Relay module
with without / local override facility
Resistance measuring module
Power supply module 1.2 A,
fuse 10A
Bus connection module,
fuse 10A
Island bus expansion module
P-Bus Interface module with power supply 1.2A, fuse 10A
Type
TXM1.8D, TXM1.16D
TXM1.8U TXM1.8U-ML
TXM1.8X TXM1.8U-ML
TXM1.6R, TXM1.6R-M
TXM1.8P
TXS1.12F10
TXS1.EF10
TXA1.IBE
TXB1.PBUS
Data sheet
CM2N8172
CM2N8173
CM2N8174
CM2N8175
CM2N8176
CM2N8183
CM2N8183
CM2N8184
CM2N8180
Device
Type
Data sheet
I/O modules with basic functions measuring, signaling, switching and controlling
I/O OPEN modules for pumps
I/O OPEN modules
PTM1...
PTM5...
PTM1...,PTE
8111 8171
866x
978x
PTM-I/O-Modules
Operation
There are various options for operation of the PXCU automation stations:
QAX... room unit connected to the PPS2 interface. A maximum of five room units
QAX (not QAX5) can be connected. Details on the PPS2 communication are
described in the DESIGO Technical principles manual (chapter "I/O blocks", section
"PPS2 addressing").
Local PXM10 operator unit, either plugged into the automation station or connected
via PXA-C1 cable
Network-compatible PXM20 operator unit (BACnet / LonTalk)
for operation of the local automation station or an automation station in a network,
either plugged into the automation station, or connected via PXA-C1 cable
Network-compatible PXM20-E operator unit (BACnet / IP)
for operation of the local automation station or an automation station in a network,
either plugged into the automation station, or connected to the Ethernet network or
an Ethernet switch.
PX-WEB: The PXA30-W extension module is used to activate the Web server,
allowing operation with a Web browser, a touch panel or a PDA.
The transfer of alarms via SMS or e-mail can be configured in the automation
station.
4/12
Siemens
Building Technologies
CA1N9221en_09
2013-02-07
Design
6
00255a
1
2
3
4/5
6
7
8
9
Plug-in unit
Front cover
(a PXM... operator unit can be fitted instead of the front cover)
Battery
Extension modules
Device socket
Plug-in connection for automation station for device supply and bus
electronics
Housing with pcb for device supply
Plug-in terminal blocks with reversible support bar (here used for wall
mounting)
00256 A
LED indicators
and service pins
TX
SERVICE TX
COM2
SERVICE
Service-Pin LONWORKS
5/12
Siemens
Building Technologies
CA1N9221en_09
2013-02-07
Concerned
LED
Color
Status
Function
Automation station
RUN
Green
Continuously off
Continuously on
Continuously on
No supply
Supply OK, firmware OK
RESET key pressed
Continuously off
Continuously on
Normal operation
Hardware fault detected during self-test or
automation station in "coma" operating state
No validly licensed firmware
Red
STATUS
Red
Quick flashes
INFO
Red
Yellow
TX COM2
Yellow
SERVICE
COM1
Red
Freely programmable
Flashing
Continuously off
Flashing **)
Flashing acc. to wink
command pattern *)
Continuously on
SERVICE
COM2
Data traffic Ethernet / IP
(PXA30-N..., PXA30-W...)
Inactive
TX COM1
TX COM2
Inactive
Yellow
Flashing
SERVICE
COM1
SERVICE
COM2
Inactive
Red
Continuously off
Flashing **)
Flashing acc. to wink
command pattern *)
Continuously on
Ethernet OK
IP address not configured
Physical identification of the automation station
after receiving the wink command
No link pulse
2s
1s
00408
5 Hz
2s
1s
For PXM20-E mounting (ethernet cable) see the mounting instructions delivered with
the operator unit!
6/12
Siemens
Building Technologies
CA1N9221en_09
2013-02-07
.
.
.
.
.
STOP
Insert the PXA30 extension module fully into its socket (to a depth of 1.5 mm),
using slight force. Then check that the plug is safely snapped on to ensure safe
and smooth functioning.
Do not touch the connector pins (electrostatic discharge)
Note!
Commissioning
In order to prevent equipment damage and/or personal injuries always follow local
safety regulations and the required safety standards.
STOP
Caution!
Download the plant operating program to the automation station with XWORKS plus,
locally via the RJ45 connector of the AS or via the LONWORKS bus.
Use the CFC in the XWORKS plus for setting the control parameters and the
configuration data. Data visible in the network can also be changed with the PXM
operator unit.
Wiring test
It is possible to test field devices and the wiring as soon as the power supply is
connected, without first downloading the plant operating program.
The test is carried out with a PXM20 or PXM20-E operator unit.
Network connection
Service functions
00257
RESET
A
Connected to
LONWORKS Force
Firmware Bus
Download
Connected to
Ethernet / IP
B
Force
Cold Start
RESET
If this key is pressed during a restart (Powerfail) the current D-MAP program is deleted
from the FLASH.
The automation station waits a short while for
the signal to activate the FWLoader and then
starts the automation station..
If this key is pressed for >5 s, the automation
station waits for a firmware download via
Ethernet.
Pressing this button during a restart forces a
cold start.
Forces a restart
Erase: refer to the CFC online help.
7/12
Siemens
Building Technologies
CA1N9221en_09
2013-02-07
Maintenance
Battery life
Lithium batteries usually have a life span of at least four years. The automation station
automatically sends a system event in order to indicate a low charge.
After the "Battery low" event there are several months of remaining life span.
Battery change
To change the battery, remove the front cover. As long as the supply voltage is
connected, the battery may be removed for unlimited time.
STOP
Caution!
To prevent hardware damage by electrostatic discharge (ESD), a wrist strap with earth
cable must be used during the battery change.
Disposal
The device is classified as waste electronic equipment in terms of the European Directive 2002/96/EC (WEEE) and should not be disposed of as unsorted municipal waste.
The relevant national legal rules are to be adhered to.
Regarding disposal, use the systems setup for collecting electronic waste.
Observe all local and applicable laws.
Technical data
General device data
Operating voltage
Safety extra-low voltage SELV
Protective extra-low voltage PELV
Frequency
Current consumption
Power consumption
Internal fuse
Operating data
Ethernet interface
(extension modules
PXA30.N, PXA30.W)
Processor
Memory space FLASH
SDRAM
SRAM
Data backup in case of power failure
Applications, parameter (FLASH)
Run-time data (buffered by Li battery)
Realtime clock (buffered by Li battery)
Interface type
Bit rate
Protocol
Connection
Wiring Cable type
Cable length
Network
Baud rate
Protocol
Interface chip
Wiring Cable type
Cable length
AC 24 V 20 %
HD 384
50/60 Hz
4A
PXC00-U
45 VA
PXC64-U
45 VA
PXC128-U
95 VA
Thermic, automatic reset
.
.
.
.
.
8/12
Siemens
Building Technologies
CA1N9221en_09
2013-02-07
Serial interface
Interface type
Baud rate / Data bits / Stop bit
Parity / Flow control
Wiring Cable type
Cable length
Polling cycle at I/O modules
Transmission speed
Signal level
Wiring Cross-section
Cable length
Cable length (special requirements)
Interface type
Supply class
PPS2 baud rate
Wiring Cable type
Capacitance per unit length
Single cable length
RS232
57 600 bps / 8 / 1
None / None
9-core standard screened cable
Max. 3m
0.3 s
62.5 kBaud
DC +23 V and 0/5 V
Min. 3 x 0.75 mm2
Max. 50 m
Max. 200 m
PPS2
4
4.8 kBit/s
4-core, twisted pair, unscreened
Max. 56 nF/km
Max. 125 m where A = 1.0 mm2
Connecting cable
Max. 3 m
P-bus interface
(PXC64-U, PXC128-U)
LONWORKS bus
.
.
IP 30
III
Class 3K5 to IEC 721
0 ... 50 C
< 85 % rh
Class 2K3 to IEC 721
25 ... 65 C
< 95 % rh
Industry standards
Dimensions
Weight
2004/108 EC
UL 916: PAZX, PAZX7
See Dimensions
Without / with packaging
0.96 / 1016 kg
EN 60730-1
EN 60730-2-11
EN 61000-6-2 (industry)
EN 61000-6-3 (residential)
9/12
Siemens
Building Technologies
CA1N9221en_09
2013-02-07
Connection terminals
00341
PXC64-U
C1
C2
1
8
G
G0
C3
PD
C4
2 PU
S
S
CLA
CLB
PC
9
4
CP+
CP
10
MMI/TOOL
G/G0
PD
PU
PC
CP+/CP
CLA/CLB
HMI/TOOL
PXC128-U
PXC00-U
The system controller PXC00-U does not have an active P-Bus interface.
The PPS2 interface is not supported for PX OPEN applications.
Tool socket
3206Z01
12 345 678
1
2
3
4
5
6
7
8
Unoccupied
Unoccupied
COM1/TxD
COM1/RxD
Connection diagrams
Connection of field devices: see mounting and installation manual for I/O modules and
P-bus (CM2M8102).
10/12
Siemens
Building Technologies
CA1N9221en_09
2013-02-07
Dimensions
All dimensions in mm
17
Front mounting
55
min. 40 mm
24
22.5
109
136
138
25
+1
0
max R2
150
min. 80 mm
137
PXM...
15 27
00232 K
+1
0
138
min. 100 mm
210
17
Wall mounting
14,5
81
00233 K
15 27
109
136
min. 80 mm
22,7
18 40,7
150
137
PXM...
min. 40 mm
55
5,2
124,5
min. 100 mm
210
11/12
Siemens
Building Technologies
CA1N9221en_09
2013-02-07
12/12
Siemens
Building Technologies
Subject to change
CA1N9221en_09
2013-02-07