Вы находитесь на странице: 1из 2

1

In Design

Safety Information and Precautions

DANGER

When a power fault or HMI fault occurs, the design of the HMI control system must ensure safety of the
user system. Otherwise, wrong output signal or HMI fault may cause accidents.
1) Protective interlock circuits for stopping or restricting conflicting operations (such as forward/reverse
rotation, upper/lower limit positioning and reciprocating movement), emergency stop circuits, and
protection circuits must be configured on the exterior of the HMI to prevent equipment damage.
2) When a fault occurs in input/output control areas that cannot be detected by the HMI, mechanical
movement may be caused in these areas. To avoid unsafe mechanical movement, a fault protection
circuit must be configured on the exterior of the HMI.
3) When a fault occurs on the relay or transistor of external modules, making related outputs (coils)
remain ON or OFF, a serious accident may occur. To avoid such accidents, set an external watchdog
circuit to monitor important output signals.
A user program must be designed to ensure the system safety when an HMI display or control fault, a
data transmission fault between the HMI and the connected device, or a power fault occurs. Such faults
may cause wrong outputs (signals) or failure and further lead to accidents.
When designing the system, ensure that a communication fault between the HMI and its controller will
not lead to device function abnormality. This is to avoid personal injury or equipment damage.

During Running and Maintenance


DANGER

Ensure that all power supplies are cut off before installation or wiring.
WARNING

Treat scrapped HMI as ordinary industrial waste.


Components such as lithium cell and capacitor may contain elements that harm health and pollute the
environment.

Designation Rules

During Installation

IT: Inovance InoTouch HMI (abbreviation of InoTouch)

2. Series code:

5: 5000 series

3. Display screen size:

070: 7-inch

4. Auxiliary features:

T: standard configuration; E: built-in Ethernet port

IT5070T

IT5070E

IT5100T

IT5104E

Resolution (mm)
Brightness (cd/m2)

4.3

7.0

7.0

10.0

10.4

480 x 272

800 x 480

800 x 480

800 x 480

800 x 600

400

300

300

300

300

Display color
Backlight source

Allowed

CPU

32-bit RISC 400800 MHz

Flash

128 MB

DRAM

64 MB DDRII

Recipe storage

256 KB

The HMI must be fixed on a panel. Pay attention to the following precautions during installation:

USB host

The HMI can be used only indoors due to the built-in LCD display screen. Ensure that the HMI
is installed correctly and the use environment complies with the requirements in the hardware
specifications (See Hardware Specifications below).
Install the HMI free from explosion hazards due to combustible gas, vapor and dusts.
Install the HMI free from high magnetic field.
Install the HMI free from direct sunlight and high temperature.
Install the HMI free from fast temperature variation and high humidity; otherwise, condensation may
occur inside the equipment and result in equipment damage.
Ensure that all cables are connected to the HMI securely . If the connection becomes loose, wrong
input or output signals may be caused.

USB client

At Wiring
DANGER

Ensure that all power supplies are cut off before installation or wiring.
During screw hole processing and wiring, ensure that no metal filings or cable end drops into the HMI.
Failure to comply may result in a fire, a fault or electronic component damage.
Perform wiring and plug or remove the cable connector only after power-off. Failure to comply may
result in electric shock or damage to the circuit.
Check cable connections of the HMI carefully and ensure that the working voltage and terminal
positions are correct. If the working voltage or terminal positions are incorrect, a fire or an accident may
be caused.

Serial port

/
COM1 (RS422/RS485)
COM2 (RS232)
COM3 (RS485)

Front view

Side view
Unit: mm

COM1 (RS232/RS422/RS485)
COM2 (RS232)
COM3 (RS232/RS485)

75
37.5

Cutting size

M4

Audio output

Video input

Optional

350 mA

350 mA

RTC

Clamp
holes

Width

30000 hours

Brightness adjustment

Ethernet port

Thickness

LED

Backlight service life

If the HMI is installed in an environment outside the storage temperature range recommended in the
manual, an LCD display fault may be caused.

Unit: mm

Length

65536 color

WARNING

NEMA-4 mounting: In this mode, cut through the metal panel according to the recommended size, and
then fix the HMI into the panel tightly with the four delivered clamp screws.
VESA mounting: In this mode, fix the HMI with four M4 screws on the user mounting bracket.
Note that the model IT5043T does not support VESA mounting.

Hardware Specifications
Display screen size

SD card interface

DANGER

The HMI adopts the following two mounting modes:

Mounting Dimensions of the IT5000

Basic Parameters
IT5043T

Mounting Mode

1. Put the HMI into the area of the panel that has been cut out..
2. Put the clamp screws into the four clamp holes around the HMI from the back of the panel.
3. Tighten the clamp screws one by one until the HMI is fixed on the panel securely. Do not over tighten
the screws.
4. To satisfy the NEMA-4 seal regulation, all delivered clamp screws must be used and the panel cannot
flex more than 0.010''.

1. Product information:

HMI Model

1. The HMI works stably in the ambient temperature of -5C to 55C (23F131F). If it needs to be used
in specific occasions outdoors, contact your supplier.
2. Install the HMI free from strong mechanical vibration.
3. Install the HMI in the panel of over 105 mm deep. Ensure at least 25 mm clearances surrounding the
HMI.
4. When connecting other devices to the HMI, make sure to locate the PLC output module, contactor,
starter, relay, frequency converter, switching-mode power supply and electrical devices of other types
away from the back of the HMI. Use shielded cables as input and output cables of the frequency
converter and switching-mode power supply, and connect the shield to the system Y grounding point.

The NEMA-4 mounting procedure is as follows:

IT 5 070 T

WARNING

Do not create switches that may result in personal injury of the operator or equipment damage on the
touch screen of the HMI. To avoid serious accidents caused by such switches remaining ON or OFF,
set circuits such as limiter that are used for monitoring important output signals and design independent
switches for performing important operations. Otherwise, wrong outputs or fault may result in an
accident.
Do not create switches, such as emergency stop switch, that are used to control device safety
operations on the touch screen of the HMI. Set independent hardware switches for performing the
safety operations; otherwise, it may result in severe personal injury or equipment damage.
Do not use the HMI as the alarm device to report important alarms that may cause severe personal
injury, equipment damage or system stop. Use an independent hardware and/or mechanical interlock
for designing the important alarm prompts and the related control/triggering devices.

Product Information

Installation Environment

VESA
mounting holes

H+1

Thank you for purchasing InoTouch series HMI (hereinafter referred to as the HMI) independently
developed and produced by Shenzhen Inovance Technology Co., Ltd. Before using Inovance HMI product,
read this manual carefully to understand the product features better and use the product more safely. This
manual mainly describes the specifications, features and usage of the HMI. For the developing environment
and design method of user programs of the product, refer to the InoTouch Editor Programming Software
Manual issued by Inovance.

Mechanical Design

WARNING

The input power of the HMI is 24 VDC. If the power input is not within 24 VDC20%, the HMI may be
damaged severely. Thus, check regularly whether the voltage provided by the switching-mode power
supply is stable.
Cut off the power supply before connecting the power cable to the HMI. Failure to comply may result in
electric shock.

(W+1) x (H+1)

75

InoTouch Series HMI User Manual

Electrical Specifications
Input voltage
Rated current

24 VDC 20%
200 mA

250 mA

250 mA

W+1
Rear view

Structure Specifications
Housing color

Metal grey

Housing material
Mounting hole dimensions (mm)

HMI Model

ABS+PC engineering plastics


119 x 93

192x 138

192 x 138

259 x 201

259 x 201

General Specifications
Working temperature
Working humidity
Storage temperature
Cooling mode
Electromagnetic compatibility
Panel IP level
Mounting mode

-5C to 55C
10%90% RH (without condensation)
-20C to 70C
Natural air cooling
CE standard
IP65
NEMA 4-mounting or VESA-mounting

Display
Screen
Size

Product Specifications

Recommended
Screw Hole Size

Physical Dimensions
Length x Width x Thickness
(mm)

NEMA 4
Mounting
W x H (mm)

Position D in VESA
Mounting Mode
(mm)

W+1
(mm)

H+1
(mm)

IT5070T

7.0

200 x 146 x 42

191 x 137

49

192

138

IT5070E

7.0

200 x 146 x 42

191 x 137

49

192

138

IT5100T

10.0

271 x 213 x 40

258 x 200

37.5

259

201

IT5104E

10.4

271 x 213 x 40

258 x 200

37.5

259

201

IT5043T

4.3

128 x 108 x 35

118 x 92

Not supported

119

93

4
Terminal Description
i

Electrical Design

i
h

i
a

h
j

d e f

i
k
m

k
Side view

Back view

Terminal No.
a
c
e
g

1
2
3
4
5
6
7
8
9

l mn

Terminal Name
Power port
Communication serial port (DB9 male)
USB host (type A)
Audio output port
VESA mounting hole (PLC board/card
fixing hole)
clamp hole
CPU indicator

Front view

Terminal No.
b
d
f
h

Signal

Pin No.

Terminal Name
Communication serial port (DB9 female)
USB client (type B)
Ethernet 53E3 (RJ45)
Battery cover

SD card slot

l
n

Power indicator
Communication indicator

+24V GND

Earthing requirements
1. The metal housing of the HMI must be earthed. The DC power ground is not connected to the real
ground internally. It is preferable not to connect both the DC power ground and the housing to the
ground because virtual point grounding introduces external noise into the system. If it is necessary to
connect the DC power ground to the ground point of Y connection, ensure that the ground conductor is
as short in length and as large in size as possible. In addition, the conductor must carry a maximum of
the short-circuit current of 10 A.
2. The ground conductor must be directly connected to the ground point of Y connection, which ensures
that the conductor does not carry current from any other branch.
CE requirements
To make the HMI comply with the EMC directives and reduce electrical noise, connect a separate #14 AWG
ground cable to the ground terminal of the power connector. This ground cable must be directly connected
to the ground point of Y connection.
Safety recommendations
1. In the position where the operator directly contacts the machinery part, for example, positions for
loading or unloading a machinery tool, or where the machine runs automatically, make the onsite
manual device or other alternative means be separated from the programmable controller and can start
or interrupt the automatic running of the system.
2. If programs need to be modified when the system is running, use a lock or other measures to ensure
that only the authorized personnel can perform such modification.

Communication Connection
The communication ports can be used for connecting a printer, a PLC or other external devices (such as
the connector of the controller), etc.
Precautions on communication connection
1. Cable requirements: Use different cables for connection of different external devices. Do not lay the
communication cables together with the AC power cables or near sources of electrical noise. Do not
plug/remove the communication cables during communication.
2. To avoid communication problems, ensure that the communication cable do not exceed 150 m when
connecting RS485/422 devices and not exceed 15 m when connecting RS232 devices.
3. If a communication problem exists, PLC no response is displayed on the screen and will not disappear
until the communication becomes normal. The communication indicator
on the panel becomes ON
at every communication.
4. Use a shielded cable as the communication cable if the cable is too long or needs to run through the
electrically noise environment.
Connection to external devices (DB9 male)
The COM1 [RS-232] and COM2 [RS-232] ports on the rear of the HMI are used for connection to the
controller with the RS232 port. The pin arrange of DB9 male is described in the following table.

COM2 [RS-232]

Pin Arrangement of DB9 Male

RXD (receiving data)


TXD (sending data)
TXD (sending data)
GND (signal ground)
RXD (receiving data)
RTS (ready to send)
CTS (clear sending input)

Connection to External Devices (DB9 Female)


The COM1 [RS485 2/4W], COM3 [RS485] and COM3 [RS232] ports on the rear of the HMI are used for
connection to the controller with RS485, RS422 or RS232 communication port. The COM1 [RS485] 4wire is
COM1 [RS422]. The pin arrangement of DB9 female is described in the following table.
Pin
No. COM1 [RS485] 2/4-wire
1
2
3
4
5
6
7
8
9

Wiring
Power supply connection
1. Power requirement: The HMI is powered by DC power only with the allowable DC voltage range of
24 VDC20%. The HMI must not share the same power with the inductive load or controller. The DC
power must be isolated from the AC main power supply correctly.
2. Emergency stop switch: To comply with the ICS safety regulations, an emergency stop switch must be
installed in any control system where the HMI is used.
3. Wiring mode: Before connecting the power cable, strip about 3/8 insulation cover off the end of the
cable. Loosen the power screw counterclockwise on the rear of the HMI, insert the power cable and
tighten the screw clockwise. Connecting mode Connect the power positive to the +24V terminal and DC
ground to the GND terminal.

COM1 [RS-232]

RS485RS485+

Signal
COM1 [RS422]

COM3 [RS485]

Pin Arrangement of
DB9 Female

COM3 [RS232]/
COM2 [RS232]

RX- (receiving negative)


RX+ (receiving positive)
TX- (sending negative)
TX+ (sending positive)

GND (signal ground)


RS485TSD (sending)
RXD (receiving)

6
PC Configuration requirements (recommended Wiring Reference
configuration)
Perform cable connection well according to the wiring
1. CPU: Intel or AMD product with main frequency mode, as shown in the following figure.
of 1 G above
VESA 4-mounting
holes x 4
2. Memory: 512 MB and above
3. Hard disk: at least 500 MB
4. Display: supporting color display with resolution
Battery
of 1024 x 768 above
cover
5. Ethernet port or USB port: uploading/
Power
port
downloading programs
Power
6. Operating system: Windows XP/Windows
connector
2008/Windows Vista/Windows 7
DB9 DB9
Ethernet port
female male

Connection of the HMI to Inovance PLC


The port of the HMI is DB9 female and the port of the communication cable is DB9 male.
Product Series
Inovance PLC H1U/H2U
Port Name
COM1 [RS485] 4w 9-pin DIN-port RS422 8-pin DIN round port
Pin No.
Signal
1
RX4
TX2
RX+
7
TX+
3
TX1
RX4
TX+
2
RX+
5
GND
3
GND
Inovance HMI

RS485+

Note that the model IT5043T supports COM2 [RS232] and other models supports COM3 [RS232].
USB ports
The USB client (type B) port supports connection to a PC for you to upload/download user programs and
set HMI system parameters. The USB host (type A) supports connection to plug and play (PnP) devices
such as USB disk, USB mouse, USB keyboard and USB printer.
Connection to Ethernet
The Ethernet port on the rear of the HMI is 10M/100M adaptive Ethernet port. The port makes the following
functions available:
1.
2.
3.
4.
5.

Uploading and downloading the HMI configuration


Setting system parameters and sumulating the HMI configuration online
Connecting multiple HMIs together by means of the Ethernet
Communicating with a PLC by means of the Ethernet
Enabling the HMI to access a LAN by connecting the HMI to a HUB or an Ethernet switch by using a
RJ45 straight-through cable
6. Connecting the HMI directly to the Ethernet port of a PC by using a RJ45 crossover cable
DIP switch
1. Normal working mode: It is set when the HMI works
in normal state.
2. System upgrade mode: It is set when the firmware
and system files are upgraded. The firmware and
system files are upgraded only in special conditions.
3. Touch screen calibrate mode: In this mode, when
you power on the HMI, a + sign is display on the
upper-left corner of the screen. Touch the center of
+ with your finger or by using a stylus. Then the
+ sign moves to upper-left, upper-right, lower-left,
lower-right and screen center successively. When
calibration of the + sign at the five points are done,
the sign disappears. The touch screen calibrate
parameters are stored in the HMI system.

Mode
Normal
working
mode
System
upgrade
mode
Touch
screen
calibrate
mode

DIP Switch State


DIP Switch ON/
OFF Indication S1 S2 S3 S4 S5
ON
1

ON
1

Warranty Agreement
1. The warranty period of the product is 2 years (refer to the barcode on the equipment). During the
warranty period, if the product fails or is damaged under the condition of normal use by following the
instructions, Inovance will be responsible for free maintenance.
2. Within the warranty period, maintenance will be charged for the damages caused by the following
reasons:
a. Improper use or repair/modification without prior permission
b. Fire, flood, abnormal voltage, other disasters and secondary disaster
c. Hardware damage caused by dropping or transportation after procurement
d. Improper operation
e. Trouble out of the equipment (for example, external device)
3. If there is any failure or damage to the product, please correctly fill out the Product Warranty Card in
detail.
4. The maintenance fee is charged according to the latest Maintenance Price List of Inovance.
5. The Product Warranty Card is not re-issued. Please keep the card and present it to the maintenance
personnel when asking for maintenance.
6. If there is any problem during the service, contact Inovances agent or Inovance directly.
7. This agreement shall be interpreted by Shenzhen Inovance Technology Co., Ltd.

Product Warranty Card


Add. of unit:

ON
1

Customer
information

After the DIP switch setting is complete, the mode will take effective after power-on again.
Do not set the DIP switch casually. This may cause damage to the system.

Programming Reference

A PC with the InoTouch Editor software developed by Inovance

A programming cable

An InoTouch HMI

Software Source
The InoTouch Editor software is independently developed by Inovance. You can contact your HMI supplier
or log on to http://www.inovance.cn and http://www.gkyp.net to obtain the latest version of the software.
Programming cable
The common programming cable of the HMI is USB programming cable with one end of Type A male and
the other end of Type B male. The cable is optional and provided by Inovance. Its model is IT5-USB-CAB.

Contact person:
Tel.:

Body barcode (Attach here):


Product
information

The HMI is user programmable. To perform programming on the HMI, you need to prepare:

Name of unit:
P.C.:
Product model:

when you use the DIP switch, take the following two aspects into consideration:

USB host
USB client

Name of agent:
(Maintenance time and content):

Failure
information

Maintenance personnel:

Service Department, Shenzhen Inovance Technology Co., Ltd.


Address: Block E, Hongwei Industry Park, Liuxian Road, Baocheng No. 70 Zone, Baoan
District, Shenzhen P.C.: 518101
Website: www.inovance.cn

Вам также может понравиться